Patchmix routing through Cubase sx3

Hey all,
I am having some trouble (obviously lol) and I am gonna start to cry pretty quick. I am not normally prone to fits of rage but I am sorely being tested here.
I am running Cubase SX3 with the Patchmix DSP version 2. I previously tried it on 1.81/1.82 with the same outcome.
1st: I can only get mic sound into Cubase if I change the Cubase inputs to wave, going direct from the mic b port on the front breakout panal does not allow sound. This is horrible, really. My patchmix strip for mic b shows input but the asio 15/16 channel Cubase uses shows nothing, not until I put cubase on wave input.
2nd: Perhaps more annoying, I can listen to my MIDI keyboard just fine through VST in Cubase as well and it sounds great. I can arm recording and woot!!! sounds great! Then I hit record, and I loose ALL sound, nothing is heard even if monitoring is on, no MIDI data is recorded, and the data track itself deletes once I press stop (sometimes) likely because nothing is there. Once I hit stop, WOW!!! it sounds great! One note, when recording and no data or sounds show, I can still see the MIDI data peak meter activating.
I figured since I am failing to get anything recorded at all, maybe I have simply screwed my settings in Patchmix. I have reset it, loaded the cubase 2 template, and still no midi. If there is ANYTHING that anyone can suggest, I would be so grateful. I have been doing this for almost a week and have merely succeeded in freaking out.
Thanks
Chris

This is quite old thread and the OP has not posted more here so I suppose you don't necessarily reach him herefrom anymore.
Your system specs could be helpful.
Could it be a settings issue (driver is set something other than your project)?
Have you installed the latest drivers (IIRC, there were some issues w/ those bundled w/ card).
Also, does other ASIO software crash too? You could try some of these:
- Native Instruments BeatPort Player - http://www.native-instruments.com/in...tportplayer_us
- Kreatives.org Kristal - http://www.kreatives.org/kristal/index.php
- Cockos Reaper - http://reaper.fm/
- Mutools Luna Free - http://mutools.com/products.html
- energyXT Standalone - http://www.xt-hq.com/
Have you already checked those two other forums mentioned in my prev. reply?
jutapa

Similar Messages

Latency and Cubase sx3

Lads please help me.
I got Cubase SX3, being the most used professional program at this current time. I can't get rid of latency. I'm using windows2k and a soundblaster Augiy2 Platinum card. I really have to get this problem solved, çause i can't work at this time.
Who will make me the happiest arranger of today?
Cookwowz

Make sure you're using the creative or audigy asio drivers and not the multimedia drivers. Yes, use asio4all it is free and good. I would not advise the use of Sblaster/Audigy cards with high and DAWS like cubase SX3. However, they are generally built for gaming and are excellent for that but it would be best to use a simpler, more dedicated card like the cheap Emus or Maudio Deltas which can be obtained for well under £100 and, using the latest drivers, are pretty rock solid at the moment. If you can afford it the Hercules is rock and easy to set up and has loads of in/outputs.
Look on the cubase forum for recommendations for other soundcards.
There is a folder which should be installed in your SX3 folder called "ignoreportfilter" which has a file of the same name and instructions for use and description. You should put this file into your SX3 folder. If it has not been installed look for it on your installation cd or at the Steinberg ftp site which can be found via:
http://www.steinberguk.com/ look at the top line, goto downloads/pc updates and look for the link to the ftp site under the header near the top of the page then just browse through the folders. You may also find you can update to SX3.01.623 if you haven't already.
ps: Have you set Win XP Processor Scheduling for "Background Tasks" ? It's vital.
Message Edited by TexS on 07-07-2005 11:06 PM

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

Problem in dynamic routing through ESB

Hi All,
I am trying dynamic routing through ESB, So I created routing service in my esb with WSDL of BPEL Process1 and a soap service with same wsdl. Then created a xsl transformation. In this xsl transformation I added below code to route to BPEL process 2.
<xsl:variable name="LocationIn"
select="http://PC-HP249:8888/orabpel/default/SyncBPELProcess2/1.0/SyncBPELProcess2"/>
<xsl:variable name="LocationOut"
select="ehdr:setOutboundHeader('/shdr:ESBHeader/shdr:location',
$LocationIn, 'shdr=http://xmlns.oracle.com/esb;')"/>
But when I am invoking this ESB through another BPEL process, Got below error message:, Is there any solution for that , I am using 10.1..3.4.0, (JDEV, and BPEL).
receiveInput
[2010/02/25 17:50:39] Received "inputVariable" call from partner "client" More...
View xml document
Invoke_1 (faulted)
[2010/02/25 17:50:39] Faulted while invoking operation "initiate" on provider "PartnerLink_1".less
-<messages>
-<input>
-<Invoke_1_initiate_InputVariable>
-<part xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" name="payload">
<SyncBPELProcess1ProcessRequest xmlns="http://xmlns.oracle.com/SyncBPELProcess1"/>
</part>
</Invoke_1_initiate_InputVariable>
</input>
<fault>
ORABPEL-08034
JTA Rollback requested.
The current JTA transaction has been aborted due to rollback request received from partner invocation.
</fault>
</messages>
</sequence>
[2010/02/25 17:50:39] There is a system exception while performing the BPEL instance, the reason is "Namespace prefix 'http' used but not declared.". Please check the error log file for more infromation. Please try to use bpel fault handlers to catch the faults in your bpel process. If this is a system exception, please report this to your system administrator. Administrator could perform manual recovery of the instance from last non-idempotent activity or dehydration point. More...
oracle.xml.xpath.XPathException: Namespace prefix 'http' used but not declared.
     at oracle.xml.xslt.XSLBuilder.startElement(XSLBuilder.java:468)
     at oracle.xml.parser.v2.XMLElement.reportStartElement(XMLElement.java:3703)
     at oracle.xml.parser.v2.XMLElement.reportSAXEvents(XMLElement.java:3564)
     at oracle.xml.parser.v2.XMLElement.reportChildSAXEvents(XMLElement.java:3576)
     at oracle.xml.parser.v2.XMLElement.reportSAXEvents(XMLElement.java:3566)
     at oracle.xml.parser.v2.XMLElement.reportChildSAXEvents(XMLElement.java:3576)
     at oracle.xml.parser.v2.XMLElement.reportSAXEvents(XMLElement.java:3566)
     at oracle.xml.parser.v2.XMLElement.reportChildSAXEvents(XMLElement.java:3576)
     at oracle.xml.parser.v2.XMLDocument.reportSAXEvents(XMLDocument.java:1537)
     at oracle.xml.jaxp.JXSAXTransformerFactory.newTemplates(JXSAXTransformerFactory.java:379)
     at oracle.tip.esb.server.service.EsbTransformer.getXSLTTransformer(EsbTransformer.java:147)
     at oracle.tip.esb.server.common.cache.TransformCachePolicy.loadEntry(TransformCachePolicy.java:50)
     at oracle.tip.esb.server.common.cache.Cache.setEntry(Cache.java:306)
     at oracle.tip.esb.server.common.cache.Cache.setEntry(Cache.java:270)
     at oracle.tip.esb.server.common.cache.Cache.getEntry(Cache.java:208)
     at oracle.tip.esb.server.common.cache.Cache.getEntry(Cache.java:181)
     at oracle.tip.esb.server.common.cache.RuntimeCache.getXSLTransformer(RuntimeCache.java:324)
     at oracle.tip.esb.server.service.EsbTransformer.doTransform(EsbTransformer.java:101)
     at oracle.tip.esb.server.service.EsbTransformer.transform(EsbTransformer.java:90)
     at oracle.tip.esb.server.service.EsbTransformer.transform(EsbTransformer.java:83)
     at oracle.tip.esb.server.service.EsbRouterSubscription.transform(EsbRouterSubscription.java:388)
     at oracle.tip.esb.server.service.EsbRouterSubscription.onBusinessEvent(EsbRouterSubscription.java:208)
     at oracle.tip.esb.server.dispatch.EventDispatcher.executeSubscription(EventDispatcher.java:138)
     at oracle.tip.esb.server.dispatch.InitialEventDispatcher.processSubscription(InitialEventDispatcher.java:545)
     at oracle.tip.esb.server.dispatch.InitialEventDispatcher.processSubscriptions(InitialEventDispatcher.java:527)
     at oracle.tip.esb.server.dispatch.EventDispatcher.dispatchRoutingService(EventDispatcher.java:94)
     at oracle.tip.esb.server.dispatch.InitialEventDispatcher.dispatch(InitialEventDispatcher.java:160)
     at oracle.tip.esb.server.dispatch.BusinessEvent.raise(BusinessEvent.java:1988)
     at oracle.tip.esb.server.dispatch.BusinessEvent.raise(BusinessEvent.java:1467)
     at oracle.tip.esb.wsif.WSIFOperation_ESB.executeRequestResponseOperation(WSIFOperation_ESB.java:288)
     at oracle.tip.esb.wsif.WSIFOperation_ESB.executeInputOnlyOperation(WSIFOperation_ESB.java:357)
     at com.collaxa.cube.ws.WSIFInvocationHandler.invoke(WSIFInvocationHandler.java:472)
     at com.collaxa.cube.ws.WSInvocationManager.invoke2(WSInvocationManager.java:437)
     at com.collaxa.cube.ws.WSInvocationManager.invoke(WSInvocationManager.java:251)
     at com.collaxa.cube.engine.ext.wmp.BPELInvokeWMP.__invoke(BPELInvokeWMP.java:826)
     at com.collaxa.cube.engine.ext.wmp.BPELInvokeWMP.__executeStatements(BPELInvokeWMP.java:402)
     at com.collaxa.cube.engine.ext.wmp.BPELActivityWMP.perform(BPELActivityWMP.java:199)
     at com.collaxa.cube.engine.CubeEngine.performActivity(CubeEngine.java:3698)
     at com.collaxa.cube.engine.CubeEngine.handleWorkItem(CubeEngine.java:1655)
     at com.collaxa.cube.engine.dispatch.message.instance.PerformMessageHandler.handleLocal(PerformMessageHandler.java:75)
     at com.collaxa.cube.engine.dispatch.DispatchHelper.handleLocalMessage(DispatchHelper.java:217)
     at com.collaxa.cube.engine.dispatch.DispatchHelper.sendMemory(DispatchHelper.java:314)
     at com.collaxa.cube.engine.CubeEngine.endRequest(CubeEngine.java:5765)
     at com.collaxa.cube.engine.CubeEngine.createAndInvoke(CubeEngine.java:1087)
     at com.collaxa.cube.engine.delivery.DeliveryService.handleInvoke(DeliveryService.java:546)
     at com.collaxa.cube.engine.ejb.impl.CubeDeliveryBean.handleInvoke(CubeDeliveryBean.java:342)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at com.evermind.server.ejb.interceptor.joinpoint.EJBJoinPointImpl.invoke(EJBJoinPointImpl.java:35)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.interceptor.system.JAASInterceptor$1.run(JAASInterceptor.java:31)
     at com.evermind.server.ThreadState.runAs(ThreadState.java:693)
     at com.evermind.server.ejb.interceptor.system.JAASInterceptor.invoke(JAASInterceptor.java:34)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.interceptor.system.TxRequiredInterceptor.invoke(TxRequiredInterceptor.java:50)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.interceptor.system.DMSInterceptor.invoke(DMSInterceptor.java:52)
     at com.evermind.server.ejb.interceptor.InvocationContextImpl.proceed(InvocationContextImpl.java:119)
     at com.evermind.server.ejb.InvocationContextPool.invoke(InvocationContextPool.java:55)
     at com.evermind.server.ejb.StatelessSessionEJBObject.OC4J_invokeMethod(StatelessSessionEJBObject.java:87)
     at CubeDeliveryBean_LocalProxy_4bin6i8.handleInvoke(Unknown Source)
     at com.collaxa.cube.engine.dispatch.message.invoke.InvokeInstanceMessageHandler.handle(InvokeInstanceMessageHandler.java:37)
     at com.collaxa.cube.engine.dispatch.DispatchHelper.handleMessage(DispatchHelper.java:140)
     at com.collaxa.cube.engine.dispatch.BaseDispatchTask.run(BaseDispatchTask.java:58)
     at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:650)
     at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:675)
     at java.lang.Thread.run(Thread.java:595)
[2010/02/25 17:50:39] BPEL process instance "260032" cancelled
Regards

In below I changed http://PC-HP249:8888/orabpel/default/SyncBPELProcess2/1.0/SyncBPELProcess2 to http://PC-HP249:8888/orabpel/default/SyncBPELProcess2/1.0 . this is working.
<xsl:variable name="LocationIn"
select="http://PC-HP249:8888/orabpel/default/SyncBPELProcess2/1.0/SyncBPELProcess2"/>

Can't get internal vSwitch to route through external vSwitch to connect to Internet using one NIC on 2012 R2 Datacenter with Hyper-V

I'm running into a bit of a problem here.
I have the following two virtual switches setup on one 2012 R2 Datacenter Physical Host w/ one (1) physical NIC:
Physical Host is running 192.168.50.120, GW: 192.168.50.1, SM: 255.255.255.0 (Cisco Router has the IP of 192.168.50.1). The Internal vSwitch Network (will contain 8 VM Servers) is 192.168.1.1. I want the VM Servers on 192.168.1.1 to be able to get Windows
Updates by being able to route through the 192.168.50.1 vSwitch but yet, still want the Networks segregated.
Both of these virtual switches/networks will be running through one NIC.
I initially setup RRAS to use NAT but I'm not sure if this is the correct configuration. It seemed to work but when I went to Activate my Product Key (via MSDN Subscription) it wouldn't recognize the key and therefore I couldn't run windows updates.
However, when I set up two of the VMs on 192.168.1.1 to use DHCP through the 192.168.50.1 Network it would work fine (i.e. DHCP, DNS and GW were all set to 192.168.50.1).
Any ideas on what I might be doing wrong or how I could setup an effective route between the two networks?
Any and all ideas are most welcome and appreciated.
Sincerely,
Wallace
Wallace Davis

Hi nbk5533,
The external virtual switch and internal virtual are isolated, you must set RRAS to connect both network zone, you can refer the following article to connect the internal
switch and external virtual switch.
Configuring Hyper-V for multiple subnets with only one NIC (Server 2008 R2 Edition)
http://blogs.technet.com/b/letsdothis/archive/2012/01/08/configuring-hyper-v-for-multiple-subnets-with-only-one-nic.aspx
The similar thread:
RRAS in VM
http://social.technet.microsoft.com/forums/windowsserver/en-US/486bcbb4-bf01-4946-b103-cd896e9dafb9/rras-in-vm
More information:
http://msdn.microsoft.com/en-us/library/windows/hardware/gg605194(v=vs.85).aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Internet speed drops 85% when routed through WRT160NL

I have a WRT160NL, and it decreases my internet speed from 3700kbps down to 550kbps when I route through it.
My ADSL modem is connected via ethernet cable to the WRT160NL, then I have an ethernet cable from port#1 of the WRT160NL to my desktop computer. With this connection, I get a download of about 550kbps.
When I route directly from my ADSL modem to my desktop (bypassing the WRT160NL) my download speed is 3700kbps. I've checked all cables and connections. What is causing the speed to drop by 85%?
thanks,
groff5
Solved!
Go to Solution.

As you are facing the problem on your Hardwired computer, then you change the settings on your Router... Once you login to the Router setup page.. Below the Setup you will find MTU size which will be set to AUTO so you need to change it to Manual and change the Size from 1500 to 1365 and click on Save Settings..... Then click on the Security tab and Disable "SPI Firewall" and Uncheck "Filter Anonymous Internet Requests" and click on Save Settings...
Now you need to power cycle your Network... Unplug the Power from the Router and Modem, Wait for 30seconds and then plug the Power to the Modem, Once all the Lights are lid on the Modem then Plug the Power to the Linksys Router...
Now you can check the Speed, what the speed you are getting it on your Computer....
If you still face the same problem then i think you need to upgrade the firmware of your Router.. Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop....
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

I can't Install cubase sx3 on my Mac pro, keep getting installation has failed

I can't Install cubase sx3 on my Mac pro, keep getting installation has failed
Does anyone out their have any answers to this please ?
Thank you.

Have you contacted Cubase support, they may have an answer.

Router won't connect comps to the net, can't acess router through comps either!!

Hey, umm... I was playin a game for a bit, and suddenly I got booted off the net. I thought it was the game just spiting me (WoW does that sometimes. It hates everyone), but it turned out to be the internet.
I called comcast, confirmed that my internet was ok, and decided to call linksys.
I went to the tech support via phone, dialed the number, and the number is telling me it can't connect the call.
So, I came here.
Now, normally I can always get into the router via my comp to see what the deal is with it. This time though, I can't even acess it!
It tells me it couldn't connect every time I try to get into it, from all the computers.
I figured it could just be a bum wire messin with me. So I went into the closet and pulled out a new one that I had just got. That one didn't work either.
Then I took one of the wires I knew worked (because it connected the computer to the modem and got online fine), and plugged it in. It didn't work either.
So frusterating...
Anyways, I upgraded the routers firmware the other day after hearing that it would give me more port fowarding slots (It DESPERATLY needs more), and all was well up until now.
It's been about 5 days since I did that, so I don't know what woulda caused this to happen all of a sudden.
Espically not being able to get to the router through a computer. That's just weird...
Well, if anyone knows anything, lemme know.
Also, let me know if the phone support comes back up some time soon.

On a side note, im not using the wireless function, and I have it turned off in the settings.

How to access to configuration page of the router through the windows phone 7 ?

Hi all
I'd like to know if there's a way to access to configuration page of the router through my windows phone 7.
I usually access the router by laptop as following: "192.168.1.1". but sometimes when I'm on my phone I need to reboot the router through my phone other then the laptop which is not near me...
I looked up for applications that should do the work, but unfortunately I got no positive result, so I'm reaching out to this very forum in order to find help and tricks so that I can figure it out
thank you in advance

Hi Happydz,
For help using Windows Phone please post in the Windows Phone forums on
http://answers.microsoft.com .
The MSDN Windows Phone Development forums are for developers to discuss writing their own Windows Phone apps.
That said, I'd expect you could connect to 192.168.1.1 from the phone's browser the same way you would from the laptop's browser.

Why is my traffic being routed through china

While connecting to a voice server located in Europe, I realised that I have a ping of 300 where I previously got around 20ms or less
So I did a traceroute, turns out my traffic is being routed through china, to cyprus and then to Europe, for what purpose?
traceroute to ts109.light-speed.com (216.127.64.68), 30 hops max, 60 byte packets
1 192.168.1.254 (192.168.1.254) 0.573 ms 0.760 ms 0.957 ms
2 213.120.155.226 (213.120.155.226) 8.748 ms 8.480 ms 9.688 ms
3 213.120.155.158 (213.120.155.158) 10.892 ms 11.330 ms 12.163 ms
4 host109-159-245-114.range109-159.btcentralplus.com (109.159.245.114) 14.495 ms 14.859 ms 15.933 ms
5 31.55.164.221 (31.55.164.221) 16.301 ms 17.112 ms 17.982 ms
6 31.55.164.109 (31.55.164.109) 18.316 ms 9.854 ms 10.631 ms
7 acc2-10GigE-0-2-0-6.bm.21cn-ipp.bt.net (109.159.248.236) 14.412 ms acc2-10GigE-0-3-0-7.bm.21cn-ipp.bt.net (109.159.248.246) 9.506 ms acc2-10GigE-0-2-0-6.bm.21cn-ipp.bt.net (109.159.248.236) 13.672 ms
8 109.159.248.48 (109.159.248.48) 20.637 ms 109.159.252.206 (109.159.252.206) 21.238 ms 109.159.248.132 (109.159.248.132) 20.103 ms
9 peer2-xe-4-3-0.telehouse.ukcore.bt.net (109.159.252.53) 21.590 ms peer2-xe10-1-0.telehouse.ukcore.bt.net (109.159.254.116) 18.727 ms peer2-xe0-0-0.telehouse.ukcore.bt.net (109.159.254.102) 22.750 ms
10 t2c3-xe-0-1-2-0.uk-lon1.eu.bt.net (166.49.211.166) 20.753 ms 21.500 ms t2c3-xe-0-2-2-0.uk-lon1.eu.bt.net (166.49.211.174) 25.339 ms
11 i-0-4-0-7-peer.ulco-core02.pr.telstraglobal.net (134.159.95.25) 23.243 ms 27.041 ms 18.730 ms
12 i-0-5-1-3.istt-core02.bx.telstraglobal.net (202.84.249.234) 202.289 ms 198.248 ms i-0-0-4-3.istt-core02.bx.telstraglobal.net (202.84.249.2) 230.943 ms
13 i-0-4-0-3.skdi-core01.bi.telstraglobal.net (202.84.219.185) 213.259 ms 225.674 ms 225.800 ms
14 i-0-2-0-8.hkth-core01.bx.telstraglobal.net (202.84.141.137) 261.573 ms i-0-2-0-5.hkth-core01.bx.telstraglobal.net (202.84.141.141) 249.423 ms i-0-2-0-8.hkth-core01.bx.telstraglobal.net (202.84.141.137) 261.567 ms
15 i-0-0-0-3.hkth12.bi.telstraglobal.net (202.84.153.182) 247.201 ms i-0-0-0-2.hkth12.bi.telstraglobal.net (202.84.153.178) 260.094 ms 247.396 ms
16 unknown.telstraglobal.net (134.159.100.98) 280.081 ms 278.679 ms 279.570 ms
17 ae6.dar01.hkg02.networklayer.com (50.97.19.33) 280.926 ms 268.843 ms 282.005 ms
18 119.81.138.139-static.reverse.softlayer.com (119.81.138.139) 277.294 ms 119.81.138.131-static.reverse.softlayer.com (119.81.138.131) 279.524 ms 119.81.138.139-static.reverse.softlayer.com (119.81.138.139) 267.113 ms
19 xe1.cr1.hkg01.light-speed.com (119.81.152.250) 290.360 ms 291.142 ms 277.008 ms
20 * * *
21 * * *
22 * * *
23 * * *
24 * * *
25 * * *
26 * * *
27 * * *
28 * * *
29 * * *
30 * * *
Here's a screenshot of a traceroute done only a few months ago
Same origin, same destination, only 270MS less latency.
I have been forced through this dumb route for a couple weeks now, why?
EDIT: Should point out, it's only when connecting to this server, all other routes are fine

light-speed/teamspeak clearly have a complex infrastructure, which probably does some form of dynamic server allocation.
Maybe they have moved their server addresses around and you still have a fixed reference to a server that was appropriate but is not any longer, and if you reset your application it would reassign you to a different one.
This demonstrates they have a complex infrastructure with nodes in various places: doesn't show exactly what it is or how to deal with it.
When I do tracert ts109.light-speed.com it comes back with Tracing route to ts109.teamspeak3.com [216.127.64.68]
ping light-speed.com gives 23 ms
ping teamspeak3.com gives 304 ms
ping ts115.light-speed.com
Pinging ts115.teamspeak3.com [94.101.84.61] with 32 bytes of data&colon;
Reply from 94.101.84.61: bytes=32 time=112ms TTL=41 <<< not as helpful as 23, but better than nearly 300

Unable to login to Switch & Router through secondary Acs ,when primary ACS is down.

Dear All,
i have configured primary ACS in DC data center and secondary ACS in DR data center, i have configured replication , and it is working well, but when we put down primary ACS , we are unable to login in switch and router through secondary ACS , i ahve dedicated link between core dc sw to core dr sw through which all traffic is getting replicated . All user , mgmt vlan are created in FWSM firewall.Kindly help.
Regards
Amit Kulshrestha

Hi Bro
I'm assuming you've configured your ACS correctly and the Cisco network devices correctly. Perhaps, this could be a bug. The reason I say this is because last week, I was implementing 2 units of Cisco ACS 1121 v5.3 (in HA mode) for a client, and i had similar issues myself. When I down the primary ACS, I'm unable to login to my network devices, eventhough my secondary ACS is UP and PINGable from all network devices.
Hence, I downloaded and applied the latest cummulative patch from the CCO website 5-3-0-40-4.tar.gpg (Release Date: 27/May/2012) and my problem solved.
Perhaps, your ACS version isn't 5.3, but the morale of the story here is, maybe patching is required for your case!!
Please do let me know the outcome. May the force be with you, bro!

Copying routing through workbench

SAP Gurus,
When I copy a routing through workbench, system is automatically recreating a BOM for that material. Now I have two BOMs for that material, which I don't want. I cant use CA03 because I am using parameter effectivity for BOMs and routings. Is there any way that system copies the routing with out recreating the BOM.
Thanks
Bobby

resolved

Video iChat problem using AIM (Routing through 2nd NIC)

routing iChat for AIM
I have a Mac Pro with both ethernet cards connected. ethernet zero is connected to my office network and ethernet one is connected to a back channel DMZ. I do not have Access to the office router and it's been configure to prevent chat. I have added routes to the table for ethernet 1and am able to chat through AIM with my wife on the iMac at the house with no issues. However when I establish a video connection it errors out. I've made sure that I have both the initial and establish connection IP's routing through my back channel. But it doesn't seem to work. If I turned off the office LAN, I have no problem connecting using video chat.
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 172.24.187.251 UGSc 22 288 en0
64 192.168.0.1 UGSc 0 0 en1
74.124/16 192.168.0.1 UGSc 0 0 en1
74.124.211.219/32 192.168.0.1 UGSc 1 0 en1
127 localhost UCS 0 0 lo0
localhost localhost UH 1 608 lo0
169.254 link#4 UCS 0 0 en0
172.24.187/24 link#4 UCS 10 0 en0
gx280image 0:19:b9:12:64:93 UHLW 0 0 en0 1166
minint-fcnjr5if 0:18:8b:1b:26:7e UHLW 0 11 en0 1077
minint-a07t9r69 0:15:c5:7:d9:18 UHLW 0 0 en0 1194
172.24.187.21 localhost UHS 0 194 lo0
172
172.24.187.251 0:0:c:7:ac:82 UHLW 18 427 en0 119
192.168.0 link#5 UCS 8 0 en1
192.168.0.1 0:9:5b:f6:96:ac UHLW 4 9 en1 1151
192.168.0.2 0:6:5b:90:c2:4b UHLW 0 44 en1 1155
192.168.0.17 0:21:e9:93:3:1d UHLW 0 0 en1 1057
192.168.0.23 0:1b:77:12:f0:6a UHLW 0 8 en1 997
192.168.0.25 0:21:e9:65:c6:33 UHLW 0 0 en1 513
192.168.0.44 0:21:e9:8f:23:7c UHLW 0 0 en1 1056
192.168.0.48 localhost UHS 0 7 lo0
192.168.0.255 link#5 UHLWb 1 100 en1
192.168.73 link#8 UC 1 0 vmnet1
192.168.73.255 link#8 UHLWb 1 89 vmnet1
192.168.222 link#7 UC 1 0 vmnet8
192.168.222.255 link#7 UHLWb 1 89 vmnet8
205.188.0/16 192.168.0.1 UGSc 2 0 en1
209.85.201.125/32 192.168.0.1 UGSc 1 0
Show the following established connections when trying to use video chat.
Proto Recv-Q Send-Q Local Address Foreign Address (state)
tcp4 0 0 192.168.0.48.50922 64.12.30.68.5190 ESTABLISHED
tcp4 0 0 192.168.0.48.50918 205.188.8.179.5190 ESTABLISHED
tcp4 0 0 192.168.0.48.50917 209.85.201.125.5223 ESTABLISHED
tcp4 0 0 172.24.187.21.50915 172.24.195.103.80 ESTABLISHED
tcp4 0 0 172.24.187.21.50914 172.24.195.102.80 ESTABLISHED
tcp4 0 0 192.168.0.48.50227 74.124.211.219.993 ESTABLISHED
tcp4 0 0 192.168.0.48.50225 74.124.211.219.993 ESTABLISHED
tcp4 0 0 192.168.0.48.50223 74.124.211.219.993 ESTABLISHED
tcp4 0 0 192.168.0.48.50221 74.124.211.219.993 ESTABLISHED
udp46 0 0 *.16402 .
udp4 0 0 *.55928 .
udp4 0 0 *.5351 .
udp4 0 0 *.5350 .
udp4 0 0 127.0.0.1.49728 127.0.0.1.49728
udp4 0 0 172.24.187.21.123 .
udp6 0 0 fe80::225:ff:fee.123 .
udp4 0 0 172.24.187.21.138 .
udp4 0 0 172.24.187.21.137 .
udp4 0 0 192.168.0.48.138 .
udp4 0 0 192.168.0.48.137 .
udp4 0 0 192.168.73.1.138 .
udp4 0 0 192.168.73.1.137 .
udp4 0 0 192.168.222.1.138 .
udp4 0 0 192.168.222.1.137 .
udp4 0 0 *.138 .
udp4 0 0 *.137 .
udp4 0 0 *.52460 .
udp4 0 0 *.53118 .
udp4 0 0 *.62551 .
udp4 0 0 *.64698 .
udp4 0 0 *.57696 .
udp4 0 0 *.58110 .
udp4 0 0 *.62845 .
udp4 0 0 *.50647 .
udp4 0 0 *.59899 .
udp4 0 0 *.57346 .
udp4 0 0 *.56231 .
udp4 0 0 *.631 .
udp4 0 0 192.168.0.48.123 .
udp4 0 0 *.60623 .
udp4 0 0 *.60450 .
udp4 0 0 *.64265 .
udp4 0 0 *.49597 .
udp4 0 0 *.54901 .
udp4 0 0 172.24.187.21.49410 .
udp4 0 0 172.24.187.21.49373 .
udp4 0 0 *.2223 .
udp4 0 0 *.53391 .
udp4 0 0 *.64030 .
udp4 0 0 *.57804 .
udp4 0 0 *.56795 .
udp4 0 0 *.54587 .
udp4 0 0 *.62597 .
udp4 0 0 *.61433 .
udp4 0 0 *.49535 .
udp4 0 0 *.50679 .
udp4 0 0 *.49810 .
udp4 0 0 192.168.73.1.123 .
udp4 0 0 192.168.222.1.123 .
udp6 0 0 fe80::223:dfff:f.123 .
udp6 0 0 ::1.123 .
udp4 0 0 127.0.0.1.123 .
udp6 0 0 fe80::1%lo0.123 .
udp6 0 0 *.123 .
udp4 0 0 *.123 .
udp6 0 0 *.5353 .
udp4 0 0 *.5353 .
udp4 0 0 . .
icm4 0 0 . .
icm6 0 0 . .
icm6 0 0 . .
as I said I can still chat, I just cannot use video chat unless I disconnect the office network. I need to leave the office network as the default route. Suggestions would be appreciated, not sure if iChat problem or routing problem.

Umm,
Not so much as a Bug but a feature.
iChat has been designed with a level of security in-built.
When you send a Visible Invite it is just that, away to trigger the other end to pop up a window.
iChat then engages in the SIP part which includes a text based connection method called SIP (Session Initiation Protocol).
This involves a behind the scenes invite and a check to see that the IP the Visible invite went to is the same one the SIP bit ios going to. (remember you can log in as many times as you wanton different apps and computers to the AIM servers), but is essentially to make sure you are connecting to who you invited.
This SIP Process is very much like an old fashioned operator call in that you call the operator they call the operator at the other end who calls the Buddy, he answers his operator who confirms he is willing to chat... etc.
As with a telephone call you want to make sure you are talking to the right person.
Like a telephone iChat has to be in "one place" in relation to the internet.
Unlike a corner plot house it can not have one "number" in one street and another in the side road (even local authorities and postal service ignore this).
The process in other IM apps is mixed.
Skype spreads it's connection over as many hosts as will accept them meaning your call could be using 30 or 40 other end users to spread that load.
Of course this also increases the ports in use giving you less security overall.
Some do seem "better" at ignoring secondary connections the way Web Browsers do.
10:33 PM Tuesday; June 30, 2009

Routing through master channel

Hi Guys,
I want to use the master channel to add some final compression to my mix but it appears not to be working e.g. sliding the volume fader on master has no effect on the songs volume.. what's the best way to check that everything's being routed through master properly?
cheers.

You can't add compression on the master fader. It is for volume only, no plugs.
To compress your mix: Be sure everything is routed to the same pair of outputs (1/2) and add compression there.

HT201342 we only have one apple id for our household. i would like to use icloud to manage all our email accounts within our household. i currently use gmail. is there a way to continue to use gmail and have messages routed through icloud so no change i

i am new to icloud. i would like to manage all our household email accounts through icloud. i currently use gmail. is there a way to route all gmail messages through an icloud email so i do not have to change my email address? also how do i create multiple email accounts using the same apple id?
thanks all.
Mike

No, iCloud does not handle 3rd party mail, and Google can already sync to all your devices without any help.
iCloud accounts are individual, there is no 'Family' account. Open an account for each user, each will have an iCloud address.

Patchmix routing through Cubase sx3

Similar Messages

Maybe you are looking for