Pavilion dv-6 3216 does not boot

I am attempting to upgrade my Pavilion dv-6 3216 with a 240G PNY SSD. First thing I did was to create a system restore disc set. Then I swapped the original 320G mechanical drive with the SSD.
I then booted the system using the recovery disc and used recovery manager to restore the system to the SSD. The process went through all 7 DVD's without error. At the end a message came up asking to remove any recovery media while the system completes the recovery process.
After I hit 'continue' the computer restarted, but it got no further than a black screen with a flashing underscore cursor at the upper left corner. I waited for at least 30 minutes, nothing else happened. I powered off the computer and restarted but the same thing happened. I went into boot manager to make sure the system was booting from the internal drive and got the same black screen.
I put back the original mechanical hard drive and the system booted to Windows 7 as before. I put the SSD into the computer again and went through the recovery process a second time. Same result - just a black screen with the flashing cursor.
I ran diagnostics on the memory and hard disc and they both passed.
I took the SSD and put it into an external USB drive enclosure and connected it to my desktop. My desktop can see all the files/folders the recovery process had copied to the SSD. Device manager identifies the partition as primary and active.
Ran a disc scan on the SSD from my desktop and it shows the drive to be healthy.
So what gives? Is there a compatibility problem with the SSD? I went into the BIOS but did not find any setup/settings for hard drives. Is there a requirement for the recovery destination drive to be the same make/capacity as the original?
Is it possible that the recovery discs are corrupt? It doesn't seem so as there were no problems/errors during the creation process or the restoration process. I would try creating another set or a bootable USB drive but the recovery manager limits the create process to 1.
Has anyone else encountered this problem after replacing their hard drive, either with another mechanical drive or SSD?
This question was solved.
View Solution.

Hello Calgary_BMW,
Welcome to the HP Forums!
I see that you have replaced your 360GB (5400RPM) drive with a 240GB SSD, and after running the system recovery, are unable to boot into Windows. This has most likely occurred because the recovery media is installing the boot loader on the SSD the same way it was on the HDD; pointing the boot loader to an alternate source, which would explain the blank screen and blinking cursor. If this is the case the recovery media will not work, so we are quite limited with options.
Option 1: Acquire a copy of Windows and run a full Windows installation, which should recreate the boot loader on the SSD and get you booting from the correct drive. After installing Windows you should be able to run your recovery media and restore your software.
Option 2: Cloning the mechanical drive to the SSD. This option requires you to connect both the 5400RPM HDD and the SSD at the same time. Your laptop only has support for one SATA connection, so this will require use of another PC with multi-SATA input (any desktop PC). There are a large number of vendors that provide software to clone drives, all of these can be found easily with a simply Google search.
Let me know how this works out for you.
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

Similar Messages

HP G60-230US does not boot (disk indicator does not come on)

My HP G60-230US does not boot up. Here's the behavior:
- Power button is pressed and comes on, wi-fi button lit orange
- Power LED near the power cord stays lit solid
- On the front-left side, the power indicator LED stays lit solid, battery LED off, disk LED never comes on and is not blinking (indicating disk is not spinning);
- During the process the caps lock indicator on the left side neither comes on nor blinks
Tried following and problem remains:
- Power off by press and hold power button for few seconds, then power back on as above
- Reset. Battery and power cord out, press & hold power button over 20 secs, then power back on.
- Tried removing battery and power the laptop with power cord alone, still no luck.
It seems that this happened after I opened memory compartment on the back panel, and removed battery once to check its model information. One thing: I did that when the laptop was in sleep mode.
Another fact: battery has become non-rechargeable in past few months and I have been using the laptop with power cord plugged in.
Please help!
Richard

Having same problems with my Pavilion Slimline s3340.uk. Bad motherboard! Mine is a Foxconn. Looking for a suggested replacement part for mine as i cant find a direct replacement unit anywhere.

New MBP i5 does not boot after hard disk swap

Hi there,
I received my new i5 MBP today. After booting it once with the installed HDD to check if it's ok, I exchanged the hard disk for the one in my Late 2008 Macbook Pro. After doing this, my Late 2008 Macbook Pro boots fine with the (new) hard disk from the new i5 MBP, but the i5 MBP does not boot with my old hard disk.
To give you some details:
- I have installed 10.6.3 on the (old) hard disk that's not booting.
- The i5 MBP boots fine from the installation DVD
- Disk utility finds and can read my hard disk, no errors
- PRAM NVRAM reset did not help
- when booting in safe mode, I can see the system stop booting after or while loading Extensions.mkext
My guess is, it tries to boot and load the wrong Extensions for the new system (CPU? GPU?). I have no idea how to fix this.
Any help would be greatly appreciated!

Focx,
Welcome to Apple Discussions.
Inserting the drive from an earlier model MBP will probably not work. The version of the system you have on that HD is designed for earlier hardware so when you put in in your new machine it's going to be recognized. What I'd recommend is re-installing the disk that came with the new machine and of course putting the 2008's disk back in the old machine. Then use Migration Assistant on the new machine and migrate your data from the old machine into the new machine.
This will provide a much more stable system and should work just fine.
Regards,
Roger

Satellite L745D-S4214 Does not boot; HDD recovery partition not working

I tried to apply the recent windows 7 updates and my laptop no longer boots. I tried to press F12 and select the HDD Recovery partition, but it does not boot regardless. There is a message that it does not communicate to a specific device. I believe the address called out was 0xc0000e9, but I am going by memory. I never created a recovery CD because I thought I was covered by the HDD partitions. This was purchased on 10/26/2012, so it should still be under warranty.
PLEASE HELP!

Hi I'm going to assume that your recovery works like mine and that the recovery partition is still good and not corrupted.
Shut down your PC. Press F12 and select HDD recovery. Click enter. This should start the recovery from the hidden recovery partition.
PS I would advise you to make the recovery discs or USB recovery Try this first.
Perform a power cycle
Even when your laptop is off and unplugged, residual power can still be held in some components. While this is normal, clearing it can help with boot problems. Perform these steps to complete what’s called a power cycle.
Ensure the laptop is turned off.
Unplug the laptop's AC power cable.
Remove the battery (if the model has a removable battery).
Unplug all wires or peripherals. This includes CDs, DVDs, USB sticks, mice, printers, and any other accessories.
Hold down the power button for thirty seconds.
Reattach the battery.
Connect the AC adaptor to the power socket that was confirmed to be working in the first step.
Connect the other end of the AC adaptor to your computer.
Try starting the computer.
If your laptop starts normally now, you're done!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

Satellite M30-107 does not boot correctly after Recovery disk usage

Hi
I've recently got hold of a second hand toshiba Satellite M30-107 laptop, and decided to freshen it up.
I used the toshiba recovery disk, but after doing so the laptop no longer loads windows.
When turned on it shows the Toshiba start up disk for about a second then goes to a blank screen and freezes.
When turned off and on again a screen comes up reporting an error in shutting down and gives the options to start in safe mode etc. but choosing any of the options causes the machine to freeze.
Any help or advice would be much appreciated.
Thanks
jt

Hi
Sounds a little bit like the notebook does not boot due to the Windows software issue
Did you recover the M30 with the original Toshiba recovery CD which was supplied with this M30 unit?
Maybe Im wrong but for me it looks like a wrong recovery CD was used and an image with non compatible drivers was installed
You could try to install the OS from original Microsoft Win XP CD and could check if it would be possible to get the notebook ruining using clean OS.
In such case we ( you and me ;) ) could find out if this issue could be related to the software or hardware.
Bye

X102e - Hard drive does not boot into Windows

Hi, I was trying to reinstall Windows on my X120e.
I tried clean install with Windows 7 Professional, but the hard drive does not boot into the Windows once it has done the first phase of the install(you know, the copying part)
After the restart done by Windows, it goes as far as "Starting Windows" but does not actually boot into the Windows.
When I try to install Windows with another HDD, the device works well, but I can't swap the HDD because it is not 7.5mm think HDD.
Is there any possibility the HDD will work trough any software-level process? The HDD works fine as external HDD when tested with external HDD adapter, and installs well. only problem is that it fails to boot
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Thank you for reply.
This is not exactly the issue. I was talking about the HDD originally installed in the PC.
The PC successfully recognizes the external disk I used to install the Windows, but the problem was that I did not boot into the "First boot" screen, which basically works on the already installed data.
As of now I have installed an SSD and is working fine. strange part is that HDD works just fine when I use it as an external HDD via adapter. Strange huh?
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Toshiba Satellite P870 upgraded to Win 8.1 does not boot

I have a Toshiba Satellite P870 with Win 8 preinstalled. Soon after upgrade to Win 8.1 and basically successful removal of “watermark error” (secure boot activated) the machine stopped booting completely: after pressing the power button ventilator sound
is heard with periodically changing loudness as well as clicking sound from the speakers. The screen stays black. Attempts to start the PC through pressing F2 or zero buttons did not produce any result. Neither did I succeed with recovery discs I created before:
the system simply does not boot from the disk. It looks like I tried all options offered by Microsoft and Toshiba. I would be happy to roll back to factory settings.
Could someone give me hint what to do next?

Hi,
For the issue, let us know how to remove the “watermark error".
Meanwhile, I would like to confirm if you could access the BIOS.
I suggest you update the BIOS version to test it.
If you want to repair the startup issue, you should use windows 8.1 recovery discs or installation discs.
Meanwhile, if you cannot access the BIOS, it may be caused by hardware, I suggest you contact the Toshiba manufacturer for further help.
http://support.toshiba.com/
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact
information.
Regards,
Kelvin hsu
TechNet Community Support

Satellite A105 WIN XP does not boot or load...

Ok, so my wife's laptop has a boot issue. Model is A105-S4284
The Toshiba/Phoenix screen loads, but does not boot/load XP. It gives a black screen, then sits for a few secs and restarts. it will continue this loop indefinetely as far as I can tell. When this happened, she complained that it has been taking longer for it to boot into XP recently. (Wish she had told me before)
I can get to BIOS system utilites, Boot menu, and can access F8/Win Advanced options boot choices. I have tried the following:
Safe Mode
Safe Mode w/command prompt
Last known GCFG
Disable Auto restart on failure
I have also done a battery pull and unseated the memory, even swapping left/right, and attempted boot from just one mempry module, all with no change.
Apparently her DVD/optical drive is toast (apparently has been) so I can't do a recovery disc, but I did make a recovery USB drive. No dice there either.
What have I not done? Since I can access the adv. opt. menu it seems winXP is still there. most likely she shut it down while XP was installing something, and now there is some type of error in the registry or somewhere, but I can't seem to recall or remember what my next steps would be to gain access to I can try to clean it up and recover.
I would do a complete wipe and start from scratch, but her entire work portfolio is on the HDD and she (foolishly) has not backed it up, at least not recently. Is my best bet to get an outboard drive enclosure and set the jumpers to slave, so I can attempt to recover the data that way?
I'm a bit stubborn, and know my way around a computer, and I refuse to give up and drop it off at the geek squad.
Please help!

Satellite A105-S4284
her entire work portfolio is on the HDD
First things first. You should rescue the files.
Remove the hard drive and place it in an enclosure accessible from a desktop via USB.
-Jerry

Reset Password - System does not boot from DVD

My System: Macbook Pro - 2Ghz Intel Core Duo - OS X - 10.6.8
Hi everyone,
i forgot my password. So i want to boot from install DVD to reset the password. Unfortunately my macbook pro does not boot from DVD (10.6.3).
I press c all the time...but sometimes the macbook pro throws the DVD out...and sometimes nothing happens.
The DVD drive is working fine...
Any other idea?
Thanks in advance.
Fabian

So when you boot holding option it shows a padlock with a password field? Is that correct?
In that case we're talking about the firmware password, which you can't reset via the install disk. There is only one way to do this, I'm not certain if one is allowed to divulge that information publicly - might want to try googling "reset firmware password"

HP Pavilion Slimline s3707c PC will not boot up all the way

HP Pavilion Slimline s3707c PC will not boot up all the way; gives the following message:
Entering Setup
<F10=setup> <F11=System Recovery
<Esc=Boot Menu> <F9=Diagnostics>
Tried to install recovery disc; did not respond.
[Personal Information Removed]

Hi wjackson95,
When you get to the screen mentioned below, can you press the F11 key to enter the Recovery system that is on the hard drive? Alternatively, if you can press F10, you can go into the BIOS and change your boot order to put your disc drive before the hard drive so that the PC boots to your Recovery discs. NOTE: You may have to press F10 or F11 multiple times to get it at the right time.
You might consider opening your PC to see if it has dust buildup. If your PC has overheated, it can cause it to not boot. It can also cause heat damage to the interal parts.
For more detailed boot troubleshooting, see this HP Support document:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00899280&cc=us&lc=en&dlc=en&product=3882331
Let us know how it goes.
...an HP employee just trying to help where I can, but not speaking on behalf of HP.

Macbook pro does not boot after upgrading ram

I have a macbook pro late 2011 which runs with mavericks operating system . I have tried to upgrade my macbook to 8Gb. Macbook does not boot when the two ram slots are filled with 4GB ram but runs well when the slots are filled with 2GB ram. When i try them individually with one slot of 2GB ram and another slot with 4GB they run perfectly which shows status ok in the RAM info. What could be the problem .

Around here, most of us recommend only Crucial and OWC for RAM because it's guaranteed to work with Macs and it's what most of us have. If I were you, I would return the RAM and look at purchasing RAM from either Crucial or OWC. If you can't get their RAM to work then you'll know that there's some trouble with your actual slots.
Good luck,
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

KT6V + sempron 2800 does not boot when BIOS saved

Hi,
I have just bought a new sempron 2800 to be use on a KT6V LSR. I plugget in my KT6V but was not recognised well (but all was working ok with windows). To be recognised, I have flashed with the last bios of MSI my motherboard... and now I have the following problem:
- I clear CMOS, then boot. It comes ok (processor detected and set a 1200Mhz)
- Then CMOS has a bad checksum: I enter setup, then load default, save.
- I reboot: the computer does not boot up.
If I re-clear CMOS I can re-enter setup and modify frequencies or other options. But when I save my modifications, then the computer does not reboot anymore (I have to re-clear cmos again)...
I tried to apply the configuation I found in this thread:
http://forums.amd.com/lofiversion/index.php/t69536.html
It says that SDRAM must be at 333, FSB at 166 and multiplicator at 12. When applying this settings, it does not boot (the leds indicate that the chipset initialisation (the first step) does not pass).
If I just load biios default, the leds indicates that it fails when checking the memory (second step of boot). I suspect that it's a problem of memory (but my memory was working well before !): it's 2x512 of DDR 400.
Any suggestion is appreciated :D . I spent several hours trying to configure the bios but it does not boot..
(I'll also try to find help on AMD forums...)
(Some extra info: my PSU is 26A for 12V, so it seems that it's not due to the PSU (as I read in the FAQ of this forum).
Thanks,
Ptitmain.

AMD Geode™ NX Processor Family & DB1500 Development Board
Powerful Software Development Capability for AMD Geode™ NX Processors
The AMD Geode™ NX processor family consists of three versatile and powerful products - the AMD Geode™ NX 1250@6W* processor, the AMD Geode™ NX 1500@6W processor** and the AMD Geode™ NX 1750@14W processor.***
The AMD Geode™ NX processor family leverages advanced architecture to provide powerful solutions for a variety of Internet edge, peripheral applications, and more. The AMD Geode™ NX processor family provides the highest x86 performance for fanless operations.
The NX processor family leverages Mobile AMD Athlon™ processor technology to deliver superior computing power for a variety of thin-client and other applications including point-of-sale terminals, kiosks, high-end printers and home media systems.
Key features include:
* Low-power consumption
* Advanced 7th generation core
* Long-term manufacturing and support
* 128KB level 1 cache
The AMD Geode™ NX processor family is supported by existing low-cost infrastructure, proven architecture and a long-term supply commitment.
The Geode NX 1250@6W processor is based on an AMD Athlon™ core and demonstrates the company’s commitment to making enhancements to its x86 product offerings and delivering a full line of x86 products to market. The AMD Geode family of embedded solutions is part of AMD’s strategy to offer assets, resources and vision for extending x86 solutions from low-power embedded solutions up through the highest-performing server platforms. The Geode NX 1250@6W processor is a cost-effective solution for customers requiring sub-one gigahertz performance without a fan. Operating without a fan not only reduces design costs and allows for better power management, but also allows the processor to co-exist in virtually any environment because it can operate silently.
The AMD Geode NX 1250@6W processor broadens the selection AMD’s customers have for x86 solutions that range from sub-one watt to 14 watts, allowing them to choose a processor that best meets their individual design needs.
.13um fabrication process
128/256KB L1/L2 cache
266MHz Front-Side Bus
Floating Point logic
AMD PowerNow!™ technology
Less than 6 watt maybe i should replace my PSU with battery (typical) to 9 watt (maximum) Total System Power Dissipation
Socket A compatibility
3DNow!™, MMX™ and SSE Instruction Set

HP Z620 does not boot when external Seagate hard drive is connected

I'm troubleshooting an HP Z620 workstation with 32GB RAM, one 500GB HDD + one 1TB HDD running Win 7 Enterprise 64 bits, this user has 2 external USB 3.0 HDDs, one Buffalo 2TB + one Seagate Desktop Backup Plus 4TB; the problem comes when the external Seagate HDD is connected and the PC is turned one, for some reason the PC does not boots, it shows a message that states "Non-disk or no boot disk error" and sometimes it tries to boot, but then goes thru the "Windows repair option" or "Start Windows normally" routine, none of these results on starting the PC.
The only way this PC starts and works properly is when PC is started with the external Seagate HDD disconnected and then connected once the Win 7 is up and running; the problem described above does not happens with the external Buffalo 2TB HDD and the Seagate HDD have been tested throughly and no errors or problems have been detected on it.
I'll really appreciate your attention to this, as well as your prompt response.
Regards,
Gaspar Campos

Hi:
You may also want to post your question on the HP Business Support Forum -- z Workstations section where there may be more folks familiar with that issue.
http://h30499.www3.hp.com/t5/Workstations-z-series-xw-series/bd-p/bsc-272#.U1k4uv1OXGg

New system does not boot properly

I just set up a new system with:
a MS-6728 Neo2 FIS2R Mobo,
1gb Geil PC-3500 RAM (2x512),
2.6C proc.
2 Maxtor 120gb IDE drives RAID 0 with the onboard promise controller.
Lite-On DVD burner
ATI radeon 9800 video card
Enermax 300 watt power supply with:
3.3v - 28amp
5v - 30amp
12v 22amp
170watt total 3.3/5 combined
My problem is that my system NEVER boots up normally. It always freezes in the bios startup. The D-bracket stops at almost every possible combination of led's, which according to the manual the problems were: Testing RTC, Initialize Video interface, Testing memory, Initializing floppy controller, Memory detection, Decompressing bios to ram, possibly more. Sometimes I also just get beeping, either a continuous beep or 8 beeps. A few times it would display the bios startup screen, but halfway down would be gibberish characters and would be locked up. When I then turn the computer off then on again, the bios is reset at least somewhat(i know because I usually disable the full screen image on startup) and says memory timings are too tight, and I have the choice to enter bios or hit any key to automatically fix things. If I hit any key it will boot up ok. However when I restart/turn off the computer, the next time it again does not boot. I tried upping the ram voltages from 2.5-2.9v, and that seems to stay that way in the bios, even when it resets itself. Everything else is set to auto/slow. If I try to manually adjust the memory timings, even to the slowest possible settings, it does not boot, and I must turn it on/off a few times till the bios resets again, with the boot process stopping at one of the possiblilitys mentioned above. Using the info tab on speedfan, I got the memory info, and it displayed the voltage at 2.5v, not sure what that means but it is strange.
What I have already attempted:
I sent back the ram and got a new set, which hasn't changed anything. The first time the other ram failed memtest, this time it passed(for about 2 hrs). So I don't think its the ram.
I borrowed an antec truepower 430w powersupply, which had no effect.
I went back to bios version 1.3 from 1.9, which also seems to have no effect.
I was hoping to overclock the system a bit and enable performance mode etc etc, but now I'll be happy to just not have to go through a song and dance everytime I restart the computer. This is only the second computer I have built from scratch, and the first with raid, but that seemed to all go ok. Please help me diagnose the problem!

I too am having problems with my system.
865PE Neo2-FIS2R
2 Maxtor 120GB S-ATA drives, RAID 0, Promise
2 512MB Geil Ultra CL2-3-3-6
HP CD-RW
What IDE settings are you using?
E.g...Native? P-ATA Only...all of those settings
For me...sometimes XP will install and boot...but eventually system is unstable and XP crashes and corrupts itself...Event Manager errors different each time
Someone mentioned problems with Maxtor and AMI BIOS...anything I should keep in mind?
Sorry about all the different questions. I'm sure exactly where my problem lies. MSI thinks it may be my memory AND/OR on-board IDE controller since I can't get the on-board Intel RAID setup to consistently "see" and setup my RAID drives...even when it has worked...XP doesn't like the Intel configured RAID drives. Also tried just one S-ATA drive through on-board Intel and Promise. Next I will try a plain old IDE Hard Drive...no S-ATA...and make sure my memory passes memtest86+ testing.
Any other gems you can offer for this config??? Thanks.

HT4790 My Mac OS Lion 10.7 FileVaulted HD does not boot, prohibitory sign, stop sign appears some minutes after boot starts. Disk Utility repair shows four error messages: Unable to bootstrap transaction group 2517: inconsistent crosscheck (the same with

My Mac OS Lion 10.7 FileVaulted HD does not boot, prohibitory sign, stop sign appears some minutes after boot starts. Disk Utility repair shows four error messages:
Unable to bootstrap transaction group 2517: inconsistent crosscheck
No valid commit checkpoint found
The volume xxxxxxxxxxxxxx(here it shows physical volume number) was found corrupt and can not be repaired.
Problems were encountered during repair of the partition map
Error: Storage system verify or repair failed.
(the same with 2518, 2519 and 2520 transaction group)
I suppose it is serious bug in Mac OS Lion managing FileVault and wonder what the help could be?

Most likely culprit is your Lacie drives which are notorious for flaky power supplies which cause just the sort of erratic behaviour that you describe. Have had similar issues myself. Lacie has been good about replacing my power converter-- twice. If you have seven of them, good luck finding the bad one or more. Like I said, the behaviour is erratic. Sometimes it'll work sometimes not. I can't comment on Samsung drives because I've never used them and have never heard anything about them. Same with Softraid. Why not just use Disk Utility. Sounds like you're ready for an external hardware raid. This will be much faster, much more reliable, and may even be cheaper than seven firewire drives. Check out G Tech, and Maxx Digital for starters.
Best of luck
Terry

Pavilion dv-6 3216 does not boot

Similar Messages

Maybe you are looking for