Pavilion dv6-1304el Additional Hard Disk and Boot

Hi to all,
I've replaced primary HD with an SSD, and at the same time I've added a second HD in the CD bay.
The problem is that the bios try to start-up system from the second hard drive (in cd bay) but this one don't has installed the OS and the notebook don't start.
If I remove the second HD, PC start-up automatically.
I've tryed to reconfigure Bios boot order, but I don't have result.
I can start-up PC typing F9 and choosing "Internal Hard Disk" from the list; at this time the system start without any problem.
How can configure Notebook to start-up automatically?
Thank you!
Simone

No the disk number is hard wired based on which SATA port the drive is connected to. I am a bit surprised that the BIOS seems to prefer the drive attached to the CD drive SATA port. Have you tried reinstalling the optical drive and then disabling CD boot, then put the hdd in the adapter back in? I do not mean just put the CD lower in the order, there is usually a keystoke you can do which disables booting from a specific device or class of devices in the BIOS. 

Similar Messages

  • T43 still can't clone hard disk and boot

    I have a T43, 1871-WKL, with a 60G HD.  I purchased a 160G Samsung HM160HC as an upgrade.  I cannot get the system to clone and boot the new drive.
    I hook up the new Samsung drive with a Sabrent USB to IDE cable and the drive works fine.  I can use it for storage with no problem.  Doing a full format with verify works like a champ.
    First I tried Acronis TrueImage 10.0.  It tells me the target media has write errors about 4% into the clone.
    So I tried Clonezilla.  It works fine, either as the same size or expanding.  I and see the drive and copy stuff on and off the drive no problem.  
    However, when I insert the drive into the carrier for the internal drive and try to boot from it, it hangs with a blank screen and blinking cursor. 
    I was TOLD that it MAY be due to the fact I have no R&R on my drive.  So I download the R&R software and installed in on the original drive and cloned it.  Again, it won't boot.  I even tried booting the R&R rescue CD.  It will boot the CD with the ORIGINAL drive in the laptop, but the CD Boot hangs if I have the new drive in the laptop.  
    I tried it with the Acronis rescue disk as well, even though I didn't have an Acronis clone of the drive.
    I must have swapped out the drive over a dozen times, and I getting tired of wearing out the mounting screws.  Any ideas?
    Mike

    Mike, welcome to the forum,
    you need to firstly create an Acronis rescue disc and then reverse clone. Install the new drive as primary in your T43 and your original drive in the USB caddy / USB -> IDE cable and then simply clone the drive.
    Please see the following article in the forum Knowledgebase; Cloning Hard Drive Including The Predesktop Area With Acronis
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

  • Should I boot from external hard disk and how do I achieve this?

    I'm in a downward spiral and need advice about if booting off of an external hard disc is the right thing to do and how to go about it. How I got into this mess I'll write below. My immediate problem is that I want to be able to install a copy of osx 10.5 from the original disks that came with my computer onto a usb hard drive. Then I want to boot from that drive and install software such as disk warrior on the same external hard drive in order to repair and recover the files on my internal hard disk. Not sure if this is easy to do with the install disk that came boxed with my macbook. So is what I want to do feasible and how do I do it? Thanks.
    How did I get into this mess?
    For those with time to read more. A downward spiral (and my macbook was working fine)::
    I have been backing up my work documents onto a 20 GB pendrive waiting to get the money to buy an nas to work with time machine for the two macbooks we have at home as a place to backup photos and video. I bought a network drive but it wouldn't work with my macbook; my time machine backup freezing at 3 gb, but works fine with wife's macbook pro.
    I tried to do TM backup on a usb hard disk and got the same problem. Support forums indicated that hard disk problems could confuse TM, so although I was experiencing problem free computing I ran disk utility from internal  osx. This indicated an <invalid node structure - file system verify or repair failed> at the checking catalog file stage. So I followed instructions to run disk utility and repair from the installation disk. When I ran disk utility from installation disk I get exactly the same <invalid node structure - file system verify or repair failed>. It gets worse.
    After failing with install disk utility, I could not then boot from my hard disk (I had had trouble free computing up to my attempts to use TM) or eject the disk. At first attempt I had no option but to boot from dvd again as hd not offered as an option. Second attempt hd option available but fails. By reading advice given to others I managed to eject the dvd and have tried:
    safe boot - it won't
    boot in verbose mode and single user (indicates I have disk0s2:I/O error) and won't boot
    try to use disk utility from install disk to create disk image on external hd, it won't (cites i/o error)
    If I can boot from an external I will try to repair with Disk Warrior as forums indicate that this software has been able to solve <invalid node structure> issues (but am open to recommendations of other products). I also hope that I may be able to try again to burn a disk image sucessfully if this repair works. I'm still trying to save my photos and videos that aren't backed up.
    I  plan to try an archive and install installation but first I want to  try a repair with disk warrior as I fear that archive and install won't work and I'll end up having to erase and repair my hard disk.
    I feel like some perverse god is punishing me for trying to do the right thing and back up my hard disk.
    Macbook 5.1 late 2008
    Intel Core 2 Duo
    OSX Leopard 10.5.8
    85 GB of a 150GB hard disk needs backing up (saving)

    I am not sure about this, but my memory is that if you try to partition the drive (in OS 10.5.8) it will erase the data.
    But you can try. Go through the Add a partition steps, but watch for any warnings. If my memory is correct there will be a message to the effect that everything will be erased. If you see that, do not proceed. This page has info about how to do it, if it can be done: http://www.macworld.com/article/1164643/live_partition.html
    With respect to DW on an external, I do that. I have a 80 GB external - I call it Emergency - with an OS, DW and TechTool Pro on it. (Since I have is a recovery partition built in with all new OS, Emergency would be of use only if I need to run DW or TTP.)  I have never yet had to use it, but it's there. It is not usually connected - I just did that for this screen shot.

  • Can I possible to use dual boot(windows 7 in internal hard disk and windows 8 in external hard disk)?

    i want to create dual boot(2 OS in 1 laptop) in my laptop but my internal hard disk reach maximum(3) logical partition so my genuine windows 7 os is not allow me to create new logical partition and install win8 pro. i planed to purchase
    one external hard disk and connect with my laptop and install win8 in external hard disk and use both win8 and 7. This is possible? If possible how to i create? please give me step by step instruction.

    This is a developers forum for the presentation manager windows forms classes and api's
    Try what has now a new name again user community forums, formerly answer forums.
    http://answers.microsoft.com
    Success
    Cor

  • I use only two channels, have plenty of memory in my hard disk, and external hard drive, no effects, and still having problems with Garage band. Giving messages as you have too many live channels

    I'm frustrated, I am doing everything you recommend, I use only two channels, have plenty of memory in my hard disk, and external hard drive, no effects, and still having problems with Garage band. Giving messages as you ave too many live channels, the disk is slow prepare...can you help?

    Quote from: Richard on 15-November-07, 20:33:05
    tornado2003,
    What you need to do is boot into Safe Mode. Then delete the VGA Drivers.
    After that boot normally and install the latest nVidia ForceWare Drivers
    Take Care,
    Richard
    i guess you missed that:
    Quote from: tornado2003 on 15-November-07, 17:26:52
    ive tryed booting xp in safe mode but it just freezes after it loads up a couple of needed files .
    ive even formatted my hard drive and tryed installing a fresh xp on it but it just keeps locking up when it gets to the "starting windows setup" .(this is just after it loads all the drivers from the xp cd)

  • I lost my Hard disk and had to replace it, how can I get another copy of lion OS, P.S. I bought my macbook pro with preinstalled Lion OS

    I lost my Hard disk and had to replace it with a new one, how can I get another copy of lion OS, as the guy at the serive center installed 10.6 for me.
    P.S. I bought my macbook pro with preinstalled Lion OS

    If you have a way to wipe 10.6.8 off, you can then reboot your machine (with no OS) and since your system came preinstalled with Lion, Internet Recovery should occur which will boot to Apple's servers into a Recovery HD for you to redownload and install Lion.
    To be safe I would first make a clone of the current installation using Carbon Copy Cloner or SuperDuper!. This way you have a way to recover.

  • HT1175 How do you back up additional hard disks to time capsule? Which disks etc. to you choose?

    How do you back up additional hard disks to time capsule? Which disks etc. to you choose?

    I can read your question a number of ways.
    If you mean a disk plugged into your computer you wish to include in Time Machine backup.. just make sure it is HFS+ formatted and remove it from the exclusion list in the TM preferences.
    If you mean a disk plugged into your TC for backup,
    You can plug a USB disk into a Time Capsule as long as it is compatible.. and the disk is formatted HFS+, ie Mac OS extended Journaled.
    You need a USB powered hub if you want to use multiple hard disks and even one might still need a hub.
    Not all external drives are recogised but for example the Touro Deskpro works fine.
    You can buy them up to 4TB.. how much added space do you want.
    Also notice that USB 2 on a TC or AE is slow.. I mean half the speed of the same disk plugged into your computer so consider if speed is relevant to you.
    You cannot use TM to backup network disks.. again I am not 100% sure what the question means.

  • HT5628 Is it possible to format entire hard disk and install windows 8 only in mac mini?

    Is it possible to format entire hard disk and install windows 8 only in mac mini?

    You can, but it's not recommended. If you are going to use Windows all the time, at least give some GBs to OS X, because you will need it to install firmware updates.
    Use Boot Camp Assistant to create a Windows partition. You can find it in /Applications/Utilities. Then, follow Apple's steps to install Windows 8 > http://manuals.info.apple.com/en_US/boot_camp_install-setup_10.8.pdf You must use a 64-bit version, and note that not all Mac minis support Windows 8. Check if yours is supported > http://support.apple.com/kb/HT5634?viewlocale=en_US&locale=en_US
    Boot Camp Assistant will ask you to download the Windows support software onto a USB drive. You will need to install it in Windows, so it's very important to download it. If not, you will have problems in Windows.
    If your Mac doesn't support Windows 8, install the Windows version the site gives you

  • Creating a Master virtual hard disk and using the same for all other VM's

    Hi,
    We would like to create a master virtual hard disk and use the same for all other VM's. Can we do that ?
    my requirements :
    1) create 10 VM's
    2) first create a master virtual hard disk with win OS and use the same to create the 10 VM's.
    3) After creating the VM's change the HDD size.
                  -- if i have created master virtual disk with 500GB , and use the same for creating a virtual machine. can we change the HDD size to 1TB ?
    After creating the VM's ,i will change the system names and activate the windows accordingly.
    Will there be any implications ,if we can/will do like this.
    Thanks.

    Hi Suren424,
    I think Using Differencing Disks may cover your needs .
    Please refer to following setps:
       "Create the Parent Virtual Machine Configuration and Virtual Hard Disk
        Install the Operating System, updates, and common software
        Generalize the installation
        Prepare the parent virtual hard disk
        Create the differencing disks
        Create virtual machines that use the differencing disks
    For details please refer to follwing link:
    http://social.technet.microsoft.com/wiki/contents/articles/1393.hyper-v-virtual-machine-vm-parent-child-configuration-using-differencing-disks.aspx
    Hope this helps
    Best Regards
    Elton Ji
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Hi to everybody, I'm new of the community and I'd like to know if anybody could help me with this issue. I have differente itunes libraries stored in differente hard disks, and I' d like to merge them all in one unique library

    Hi, I' m new of the community and I hope I'm not asking something that has been already discussed. I have different iTunes libraries on different hard disks and I would like to merge them in an unique library - mantaining all the metadata - so that I can use this new one with iTunes Match. Could anybody help me?

    PowerTunes - http://www.fatcatsoftware.com/powertunes/ (commercial software)
    syncOtunes - http://homepage.mac.com/oligrob/syncOtunes/syncOtunes.html
    Alison 1231, your question is not identical to the original poster's so perhaps you could start a new topic with the question since the answers will be different and not apply to the OP's post.

  • How can i access the hard disk and know the no of partitions

    sir
    i want to access the hard disk and know how many parttions the hard disk have means c,d,e,f,g or may be c,d,e? also volum no or serial no.
    but i do not know how?
    plz help me and send me a code
    thanks in advance
    if this quesstion is not related to this forum plz guide me that where i put this quesstion?

    You figure out how to do it on your OS using C/C++ code.
    Then you write a wrapper in JNI to call your C/C++ code.

  • I'm not able to copy and paste files from my mac to hard disk and usb. I have tried dragging the items to those devices but it won't work. I also have tried copying and pasting those files onto those devices but that doesn't work too. Can any one help?

    I'm not able to copy and paste files from my mac to hard disk and usb. I have tried dragging the items I want to copy to those devices but it won't work. I also have tried copying and pasting those files onto those devices too but that doesn't work too. Can any one help?

    Hi BobRz
    Thanks for you suggestion but it didn't work - are there other ways for solving this problem? Or is it because my files that I want to copy and paste onto my hard disk etc are too big? (However there is space on my hard disk and it works on a PC)

  • I have transfered all my library on an external hard disk and lost the itunes library files.

    I transfered all my library on an external hard disk and lost the itunes library files. Itunes created new ones but I lost all the playlists.
    How can I copy the playlists presents on the Iphone directly on Itunes ?
    If I want to syncronise now, I lost all playlists datas.

    Hi,
    I did the same XP to Windows 7 upgrade about 18 months ago.   I decided to keep iTunes permanently on the external drive than the c drive to save c: drive space. 
    ITunes database has pointers to MP3 files located in Artist's directories.  If you want to use a different location than the default C:\ drive for iTunes, then you need to recreate the Itunes database by deleting all songs in iTunes, then change the default location for iTunes files to your external drive.  Then import the MP3 files from the external drive into the empty iTunes database through the iTunes import facility.  
    If you screw up the timing of the import and find you have multiple iTunes directories (instead of just the default location), then iTunes has a new feature to consolidate all iTunes MP3 files back into the central default location.  In iTunes, FILE, LIBRARY, ORGANIZE LIBRARY, then CONSOLIDATE FILES.
    To change the default directory for MP3 files, in Tunes go to EDIT, PREFERENCES, ADVANCED and then CHANGE the location to where you want the Itunes MP3 files to be located (including the iTunes subdirectory under which all the artist directories are held.  Mine are on the F: drive or whatever your computer states is your drive assignment for the external drive.
    Note iTunes 10.5 has many problems that Apple hopefully are working on....we seem to have gone backwards on working components in this iCloud based release.  So maybe keep on using old computer until 10.6 is released.
    Enjoy
    Steve Mc (Sydney AUSTRALIA)

  • How can i format my MacBook Pro hard disk and recover my data from time capsule?

    Hello,
    My MacBook Pro is running slow, more and more. Everything started with the "upgrade" to Lion.
    Can I re-format my hard disk and recover from Time Capsule only the data and applications I really need (including Snow Leopard as OS, maybe)?
    Thanks

    The problem is that it is a Western Digital 3.5 inch internal hard drive housed inside a hard drive caddy. So the only way to connect it to my computer is through a dock.

  • I have the latest Mac Air 13" and I have a Seagate 500MB external hard disk I cant copy or Cut any files on the hard disk and I cant even delete any files. I have the settings as Read and Write in the get info tab. Please help

    I have the latest Mac Air 13" and I have a Seagate 500MB external hard disk I cant copy or Cut any files on the hard disk and I cant even delete any files. I have the settings as Read and Write in the get info tab. Please helpand also note that my hard drive was formatted on a Windows 7 Laptop.

    thats the problem, its in MSDos (Fat) or NTFS for Windows.
    Options.....
    1. offload all that data on the HD onto your PC, THEN format the HD in EXFAT for use on BOTH PC and Mac for read/write.....then reload all (or as you need) that data back onto the HD
    2. get another HD, and format it for Mac OSX extended journaled.
    FAT32 (File Allocation Table)
    Read/Write FAT32 from both native Windows and native Mac OS X.
    Maximum file size: 4GB.
    Maximum volume size: 2TB
    You can use this format if you share the drive between Mac OS X and Windows computers and have no files larger than 4GB.
    NTFS (Windows NT File System)
    Read/Write NTFS from native Windows.
    Read only NTFS from native Mac OS X
    To Read/Write/Format NTFS from Mac OS X, here are some alternatives:
    For Mac OS X 10.4 or later (32 or 64-bit), install Paragon (approx $20) (Best Choice for Lion)
    Native NTFS support can be enabled in Snow Leopard and Lion, but is not advisable, due to instability.
    AirPort Extreme (802.11n) and Time Capsule do not support NTFS
    Maximum file size: 16 TB
    Maximum volume size: 256TB
    You can use this format if you routinely share a drive with multiple Windows systems.
    HFS+     ((((MAC FORMAT)))  (Hierarchical File System, a.k.a. Mac OS Extended (Journaled) Don't use case-sensitive)
    Read/Write HFS+ from native Mac OS X
    Required for Time Machine or Carbon Copy Cloner or SuperDuper! backups of Mac internal hard drive.
    To Read HFS+ (but not Write) from Windows, Install HFSExplorer
    Maximum file size: 8EiB
    Maximum volume size: 8EiB
    You can use this format if you only use the drive with Mac OS X, or use it for backups of your Mac OS X internal drive, or if you only share it with one Windows PC (with MacDrive installed on the PC)
    EXFAT (FAT64)    ------Can read/write from both PC and Mac
    Supported in Mac OS X only in 10.6.5 or later.
    Not all Windows versions support exFAT. 
    exFAT (Extended File Allocation Table)
    AirPort Extreme (802.11n) and Time Capsule do not support exFAT
    Maximum file size: 16 EiB
    Maximum volume size: 64 ZiB
    You can use this format if it is supported by all computers with which you intend to share the drive.  See "disadvantages" for details.

Maybe you are looking for