Pavilion m7 1015dx, win7 will not complete installation on a new Samsung ssd
Trying to do a clean install of win7 on a new ssd. Seems to be going well until time for reboot. then things go downhill from there, until nothing responds. Nothing I try helps. I tried from both a iso win7 disc, and from a disk I have from my desktop. Same results. Is it possible to do a recover onto a new ssd? If so, how?
Thanks
This question was solved.
View Solution.
You're very welcome.
Unfortunately, there is no way to change the drive controller setting to AHCI but that really should not have mattered since your notebook has an Intel Series 7 chipset which when you install the latest Intel RST software for your model allows for TRIM support for SSD's.
So, make sure you have installed this driver and software, and then see this related post below that.
There should have been no degradation in the performance of your SSD.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-102490-1&cc=us&dlc=en&lc=en...
http://h30434.www3.hp.com/t5/Notebook-Hardware/How-to-enable-AHCI-for-HP-ENVY-TouchSmart-m6-k015dx/m...
Similar Messages
-
3rd gen iPod will not complete the RESTORE process with new Hard Drive
I have an 3rd gen iPod and I have replaced the hard drive with a newer MK2006GAL. The drive formats fine with a USB cable, formating Mac OS Extended Journaled. It will not complete a "restore" when connected via FireWire in iTunes or with any ipod updater utility. this happens on any mac (we have several). It will not even see the iPod updater when connected via USB and it says MUST CONNECT WITH A FIREWIRE CABLE. It will not format with Disk Utility when connected with the Apple FireWire cable only USB. This is the second new hard drive I have tried. I thought the first "replacement drive" was bad. Turns out it must be something else. Does this sound like a bad battery or motherboard or bad FireWire cable to you? The connectors look fine (under magnification). other problems, while this iPod will not Restore properly, it also will not turn off.
Would like to know if anyone else has seen this trouble.
thanks.
Powermac G4 1.25 MDD, OS9/OSX, 3rd gen iPod Mac OS X (10.3.9)
Powermac G4 1.25 MDD, OS9/OSX, 3rd gen iPod Mac OS X (10.3.9)
Powermac G4 1.25 MDD, OS9/OSX, 3rd gen iPod Mac OS X (10.3.9)Hmm now getting this message.
"The ipod "ipod" could not be restored.An Unknown Error occured (1429)".
It still will not format. Does anyone know what a 1429 error is?
Powermac G4 1.25 MDD, OS9/OSX Mac OS X (10.3.9) -
My ipod touch is not listed as a device when connected to my computer. As suggested I attempted to download the latest of itunes. I got an
ox8007054f error code and the down load will not complete. I have also tried to restore my computer to an earlier setting, but it will
not accept the change.Have you looked at this completed previos discussion. It discusses 0x8007054F.
Re: Error message when trying to install iTunes -
Pages '08 will not complete save function. I must force quit to save.
Pages '08 will not complete save function. I must force quit to save.
When saving, try "Save As" but make sure "Include preview in document" is NOT selected.
-
I have rented two movies on my laptop and they will not completely download..it shows that they are theere but when i try to watch them on my laptop or my ipad it wont open up???? help
Welcome to the Apple community.
A number of people have reported similar issues recently, many appear to have found a discrepancy of some kind in their account settings and making changes to these settings or simply resetting them has resolved the matter.
Check your account details are correct, check that you are using the correct details for Location, Region and Time Zone. You may want to change these settings and then change them back to see if that helps.
You might also try logging out of and then back into your iTunes account (Settings > iTunes Store > Apple ID’s > Sign Out) and restarting your router. (Some have reported that after doing this, they need to check for rentals even though it may report that there aren’t any, after which rentals once again appear in the ‘movies’ feature)
Rentals should appear under their own heading in the ‘Movies’ feature, you might also check at Settings > iTunes Store > Check For Rentals. -
My iPod 5th gen will not completely turn on it shows the apple symbol then shuts off I have restarted it and tried to plug it into my computer but cannot find it to restart it
Its been like this for awhile and I can not fix itTry:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Epson Perfection 1200 scanner continues to function as a flatbed scanner but when I try to scan transparencies/film negs the control panels change in Image Capture but the scanner bar will not complete the overview scan & cannot travel beyond the first 2/3 centimeters. All the communications seem to recognise the scanner and the mode for the intended scan but the necessary overview scan is not completed, nothing comes up on the Image Capture scan window. If I unplug the film adaptor I can get a document scan. When I plug in the adaptor again the Image Capture details change which allows me to select the type of scan required but when the scanner attempts an overview scan it is unable to complete it.
I have had the scanner from new (12 Years) and have previously scanned slides and film with the adaptor but maybe this was before I upgraded my computer (imac 27").
Do I have to buy a new scanner? It seems so close to working correctly.
I have downloaded the Epson recommended driver (5.4) and have Epson Perfection 1200 6.6 Universal showing in the Applications List.
Any thoughts or observations would be much appreciated before I go out and spend money an new hardware.
ThanksI have same issue - have you solved this yet?
-
My iTunes library will not completely sync to neither my iPad nor my iPhone -- both are completely updated with the latest software. What do I have to do?? When I try to do the "autofill" option when connected to iTunes it says "no songs can be copied"...I literally bought some of these songs yesterday on my iPhone and now I can't sync them to my iPad. What is this issue? Usually I would just have to plug either device into iTunes and everything would sync, now nothing new syncs.
On your iPad tap Settings > Store
Switch Books off then back on then reset your iPad.
Hold the On/Off Sleep/Wake button and the Home button down at the same time for at least ten seconds, until the Apple logo appears. -
I tried to download the app "Google Translate" from the App Store onto my iPhone 5s. However, the download will not complete. As well, when I try to delete the icon from my home screen, it will not go away. I am very frustrated as this has never happened before and I have gotten many paid and free apps from the App Store. I hope someone can solve my dilemma. Thank you kindly.
What have you tried to get the app to finish downloading e.g. have you tried logging out and back into your account on your phone, disconnecting and reconnecting to your network, soft-reset of your phone (press and hold both the sleep and home buttons for about 10 to 15 seconds, ignore the red slider, after which the Apple logo should appear and it should reboot) ?
You could also try downloading the update on your computer's iTunes and see if you can sync it over to your phone (or delete the app its Apps tab when connected to your computer's iTunes and sync the new version - deleting the app will delete its contents). -
My MacBookPro (mid 2012) will not complete the boot process. Yosemite's progress widget gets about 1/3 to 1/2 way across when the logo disappears and the screen goes all white for 10-15 secs, then the machine shuts down and restarts. This sequence will repeat seemingly forever unless I shut it down manually.
I upgraded to Yosemite from Mountain Lion a couple months ago, skipping Maverick completely, and I've done any associated updates that Apple told me about. I don't recall which version of Yosemite I have, but I'm sure it is the "latest and greatest".
I've tried re-starting in Safe Mode / Safe Boot and that does the same thing as described above except without the endless restarts. Instead of restarting at some point, SafeBoot proceeds to the white screen and then it hangs until I restart it manually. (I've waited as long os 20-30 minutes with no response).
When I tried the option-command-p-r key combo I never get any chimes or other noises besides the original 1 time boot sound that you would expect to get when starting up a macbook pro.
I was using the mac quite normally (meaning I was doing work I normally do on it and there was no indication of anything wrong) immediately prior to this happening.
The machine is BootCamp(ed) with Windows 8.1 which I use from a VMWare virtual machine instead of natively so that I can have both OSes running at the same time. I also think this is unrelated to my problem. I have been using this setup for more than 2 years.
My upgrade to Yosemite was uneventful and I thought it went well and was very smooth. I don't want to lead attention away from Yosemite, but at this point my problem does not seem related to the upgrade.
Any help is appreciated.Install or Reinstall OS X from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
the Security button and set the Zero Data option to one-pass. Click on
the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless. -
My iPhone 4 will not complete a back up. Error - 5000 comes up
Error 5000 appears after "preaparing phone for back up" completes. "Continuing will result in the loss of all contents of this phone" is the message. Phone will not complete a synch and iTunes often goes into "Not responding". I have repaired iTunes by downloading the software from Apple's website. No improvement.
Can anybody offer a solution?This is a bad situation. Your iPhone is in a state which cannot be backed up, and the Restore will return iPhone to factory specs erasing it. You need to Restore your iPhone to get it working again. If you were experiencing problems before, maybe your iPhone is damaged. If still faulty, and you have Warranty or AppleCare take iPhone to Apple for evaluation. If no coverage and still faulty it may be time for new phone.
-
HP Pavilion Slimline s3707c PC will not boot up all the way
HP Pavilion Slimline s3707c PC will not boot up all the way; gives the following message:
Entering Setup
<F10=setup> <F11=System Recovery
<Esc=Boot Menu> <F9=Diagnostics>
Tried to install recovery disc; did not respond.
[Personal Information Removed]Hi wjackson95,
When you get to the screen mentioned below, can you press the F11 key to enter the Recovery system that is on the hard drive? Alternatively, if you can press F10, you can go into the BIOS and change your boot order to put your disc drive before the hard drive so that the PC boots to your Recovery discs. NOTE: You may have to press F10 or F11 multiple times to get it at the right time.
You might consider opening your PC to see if it has dust buildup. If your PC has overheated, it can cause it to not boot. It can also cause heat damage to the interal parts.
For more detailed boot troubleshooting, see this HP Support document:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00899280&cc=us&lc=en&dlc=en&product=3882331
Let us know how it goes.
...an HP employee just trying to help where I can, but not speaking on behalf of HP. -
Mavericks 10.9.1 keeps erring during the download and will not complete. What do I do?
Mavircks 10.9.1 keeps erring during the download and will not complete. What do I do?
Get the official version of Firefox here: http://www.mozilla.com/en-US/firefox/
As long as you '''''don't''''' select the option to '''Remove Firefox personal data and customizations''' when you un-install that "Yahoo version", you won't lose anything. -
Lightroom 5 will not complete download on Mac OS X 10.6.8
I have purchaces Creative Cloud package 5 of the segments have downloaded ok but Lightroom 5 Gaming SDK 1.3 and Scout CC will not complete download any advice.
Lightroom 5 will not run on Mac OS X 10.6.8
http://www.adobe.com/products/photoshop-lightroom/tech-specs.html
Lightroom 5 requires OS X 10.7 or higher. -
I just tried updating ITunes to the new version and it will not completely download and now I get an error message of MSVCR80. Is there a problem with the new iTunes version?
Now ITunes won't open.Help!!!Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features(Later)
Remove all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support
Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
See also HT1925: Removing and Reinstalling iTunes for Windows XP or HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
Should you get the error iTunes.exe - Entry Point Not Found after the above reinstall then copy QTMovieWin.dll from:
C:\Program Files (x86)\Common Files\Apple\Apple Application Support
and paste into:
C:\Program Files (x86)\iTunes
The above paths would be for a 64-bit machine. Hopefully the same fix with the " (x86)" omitted would work on 32-bit systems with the same error.
tt2
Maybe you are looking for
-
CPU Fan Header died .. Options ?
My CPU voltage header died , after of the instalation of one low RPM fan Papst 8312L . ( In 5 minutes time it died... I had never use the this voltage header , as i have one external voltage regulator circuit) . But i tried for first time to operate
-
STO Accounting entries for indirect costs
Hi experts, I have following scenario: Plant A Quantity Update Plant B Value/Quantity Updatae Then I create STO from plant A to Plant B. Include Indirect costs. No accounting entries is getting generated at goods issues nor goods receipt. System allo
-
How to install acrobat professional 7 on windows 8
I just purchased a new computer that runs windows 8. I have acrobat professional 7 installed on my old computer, unfortunately I downloaded it directly from Adobe and didn't get a CD, I only have my product registration receipt with a serial number.
-
Periodic values for INC/EXP accounts in YTD application (first period only)
Greetings, I have a YTD application. INC/EXP account balances are imported as YTD. When I choose the Periodic measure for the FIRST period of the year, BPC calculates the difference between the YTD value for the first period (which is really the pri
-
Unable to access URL for a webservice in weblogic integration server
Hi I have an application in which i deployed a webservice , however when i am trying to access it , it throws the exception weblogic.webservice.tools.wsdlp.WSDLParseException . "failed to retrieve WSDL from URL"