Pavilion sleekbook 15 b002tx ram friquency

i am using hp pavillion sleekbook 15. b002tx.
it has 2 gb ddr3 RAM pre installed.
i want to increase my RAM.
I dont know what is friquency of RAM.
please suggest me what specification of RAM is required for my laptop.

Hi:
Below is the link to the service manual for your notebook.
http://h10032.www1.hp.com/ctg/Manual/c03733729.pdf
Memory upgrade info can be found in chapter 1 on pages 3 & 4.
Make sure you get the memory that matches what is listed for the chipset and processor your model has.
Check the existing 2 GB module you have to see if it indicates if it is DDR3L or just DDR3.
DDR3L is Low Voltage memory that = 1.35V.
You will need to get a memory chip that matches whatever voltage that one is.

Similar Messages

  • Pavilion sleekbook 14 Help

    I want to upgrade the ram on my pavilion sleekbook 14 and can't figure out how to remove the back panel. Model: 14-b015dx

    Hi:
    Wasn't the service manual of any help to you?
    Basically you have to remove the motherboard to get to the memory. It does not look like a simple job.
    http://h10032.www1.hp.com/ctg/Manual/c03560607.pdf
    Paul

  • Pavilion Sleekbook x64 has grainy and distorted images, color is mostly red, anyway to fix this

    Intel(R) HD Graphics 400
    HP Pavilion Sleekbook 14: images are grainy, distorted and mostly red.  Can anyone help.

    Hi @ramses66 ,
    Thank you for visiting the HP Support Forums and Welcome. I have read about your HP Pavilion 14 Sleekbook and images being distorted or red. Try connecting the notebook to an external monitor with VGA or HDMI. Here is a document to show you how to do that if needed.
    If it is you are having issues with a graphics card.  If it doesn't happen on an external monitor we dealing with a hardware issue with the display.
    Here is a document on Resolving Video and Graphics Issue.
    Hope this helps.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • No audio output device is installed on my laptop (HP PAVILION SLEEKBOOK 15 PC WINDOWS 8)

    I BOUGHT MY LAPTOP LAST 4 MONTHS. AUDIO IS WORKING PROPERLY.. BUT WHAT HAPPEN IS MY LAPTOP UPDATE THEN WHEN I OPEN NEXT DAYS IT SAYS NO AUDIO OUTPUT INSTALLED ON MY LAPTOP.. MY LAPTOP IS HP PAVILION SLEEKBOOK 15 PC WINDOWS 8.

    Hi,
    Try using Recovery Manager to reinstall your original Audio Driver ( probably IDT ) - the procedure for using recovery manager to reinstall Software and Drivers is detailed in the document on the link below.
    Recovery Manager - Windows 8.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • HP Pavilion Sleekbook 15 not booting up from USB (to clean install windows)

    Hello there, 
    I have been trying to install windows 7 ultimate using from USB on my HP Pavilion Sleekbook 15 (Model: b153cl) but unfortunately even after changing the boot order on bios to the USB device it's still not picking up the USB to clean install windwos 7. 
    Machine came with pre-installed windows 8, and I hate that.
    Can someone help me figure out the issue here... cause i have used the same bootable USB (windows 7) on another machine and it worked without any issues. 
    Thanks 
    Mike

    well.. i was just reading this thread, http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/HELP-download/m-p/4240018
    and my problem has been solved... 
    thanks anyway for the prompt response.. 
    Mike
    Huffer wrote:
    Have you turned off secure boot in the BIOS and enabled legacy boot? If the machine originally came with Windows 8 secure boot is enabled by default and it will block booting from Windows 7 media. 

  • HP Pavilion SleekBook 15-119wb USB, SM BUS Controller Driver

    Hello everyone,
    I have recently downgraded from Windows 8 to Windows 7 and I have having trouble in regards to finding the USB controller driver, and SM Bus Controller driver for my HP Pavilion SleekBook 15-119wb. I have tried everything so if anybody could please help me with this issue I would be very grateful.
    Specs: HP Pavilion 15-119wm Specs

    Hi:
    Normally, the usb 3.0 drivers do not install on your model after installing the above chipset driver.  Only the smbus controller installs.
    Use these two drivers to install the usb 3.0 controllers, and between all of the above, you should be all set.
    http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5359417&sp...
    http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5359417&sp...

  • Hp pavilion sleekbook 15-b002ee not being supported by the support wizard

    Product name: hp pavilion sleekbook 15-b002ee
    operating system : windows 8
    product key: C6K58EA 
    The above mentioed sleekbook was purchased in the month of february of this year. I had aoriginal windows 8 o.s which came along with the sleekbook.
    within 3 months of purchase ,due to some booting problem i got my hard disk replaced by an authorized hp service centre.
    before replacing the hard disk ,neither i was told to keep a backup copy of the recovery drive nor the staffs at the service centre did it.
    After replacing the hard disk they suggested me to order a recovery media through the customer care,and for the temporary usage they installed a trial version of windows 8.
    I have been calling the customer care and following up for seven months. it seems they dont have the recovery media for this particular model and as they have denied to deliver me the recovery media , i tried connecting through the HP support wizard online.
    In the product identification segment it says that your product is not being supported by the hp support wizard anymore.
    I am completely helpless. I have been facing this problem (recovery drive) from past 7 months and now my warranty is going to expire in two months .Its been only 10 months buying this product.even i'am not getting any appropriate solution for this problem from the technical support of Hp.
    This is my last hope to get my issues solved.
    Thanks and Regards...
    sahal_hash

    Depending on what country the keyboard is from, there can be a set of secondary symbols on the keys (most of the time in blue) the preferred language is then chosen to match a given keyboard in the "Control Panel" under "Region and Language"
     I dug around a bit and found this Arabic keyboard as an example _ it has the normal letters on it, but also some very different symbols.
     If you went for a simple US keyboard then that will work fine in your machine, but you may have to change the region in the control panel as mentioned.
     What ever the one you get, just make sure that the screw down posts and any tabs are in the same position. They will be very close to your original or not match at all so in most cases you can make a pretty good comparison.
     Have you removed the keyboard yet, if you really want to be sure, remove it and take some digital photos of the underside and top side and post them here ?
     Then I can tell you for sure if a given keyboard will fit.
     Here is a link to the HP Media Library.
     http://h20574.www2.hp.com/default.htm?lang=en&cc=us&hpappid=psml
     There is no 15 series list for the Sleekbook, just for the 14 series, but the procedure to remove the keyboard looks the same.

  • I want to know how to remove the back cover of my HP Pavilion Sleekbook 15 to install new memory?

    I want to know how to remove the back cover of my HP Product name: HP Pavilion Sleekbook 15 to install new memory?  All the HP website shows is how to remove memory covers.  Unfortunately, with newer models like mine, the whole back cover needs to be removed.  I have tried unsuccessfully to remove it but so far all that I have succeeded in doing is to scratch my cover.  So can anyone help???
    This question was solved.
    View Solution.

    Hi,
    The procedure is detailed starting on Page 67 of your Maintenance & Service Guide.
    Note:  I don't work for HP, but looking at the degree of disassembly required, I would say the procedure may well void the conditions of warranty.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Pavilion Sleekbook 15-b142dx Will Not Power On/ No L.E.D. Lights

    Hey all, had my laptop for some time now with next to no issues until now. Put laptop in a bag and put it in a back seat to just drive down the street. Arrived at destination to find it would not power on nor indicate it was charging.
    Battery was at 80% before leaving so it is not dead. Power block receives power which is indicated by green L.E.D. light on power block and pin connectors look fine on both ends. Removed battery to boot from AC power, but nothing. Attempted a hard reset to no avail. I am somewhat knowledgable on internals so I had a look inside, but apart from some dust accumulation everything was connected as should be and I did not see any foreseeable damage to any hardware. Checked voltage levels on AC adapter and it does receive power.
    I just checked my warranty status and I'm all green, but before jumping to that and having to be stuck with a Aspire One Netbook I would like some Q&A. Might have missed something, who knows. I have gone through support page and attempted everything relevant thrice.
    TL;DR:
    -Laptop (Pavilion Sleekbook 15-b142dx) does not power on nor indicate it recieves (L.E.D. lights)
    -Nothing damaged physically
    -Already went through entire support page
    Thank you!

    Hi finitedgk,
    Welcome to the HP Support Forums! 
    I am sorry to hear about the power issue, you are having with your HP Pavilion 15-b142dx Sleekbook. When you have the power connected can you get into the BIOS at all. If so, then you can try Restoring the BIOS, the steps are found in this document.
    If not then please call our technical support at 800-474-6836. If you live outside the US/Canada Region please click the link to get the support number for your region. Contact HP Worldwide
    I hope this helps, please let me know how it goes.
    Good luck and have nice day!
    I worked on behalf of HP.

  • HP Pavilion dv7t-7000 CTO RAM DDR3 or DDR3L

    HP Pavilion dv7t-7000 CTO RAM DDR3 or DDR3L?
    The manual does not specifically which of the two.
    Any idea?
    This question was solved.
    View Solution.

    David_kata wrote:
    HP Pavilion dv7t-7000 CTO RAM DDR3 or DDR3L?
    The manual does not specifically which of the two.
    Any idea?
    Hi,
    Both modules can be used. DDR3L means that the memory uses low voltage. Means the modules produce less heat and last longer than pure DDR3 ones. I still use pure DDR3 Corsair 1600MHz CL9 modules. 
    Dv6-7000 /Full HD/Core i5-3360M/GF 650M/Corsair 8GB/Intel 7260AC/Samsung Pro 256GB
    Testing - HP 15-p000
    HP Touchpad provided by HP
    Currently on Debian Wheeze
    *Please, help other users with the same issue by marking your solved topics as "Accept as Solution"*

  • Hp Pavilion dv7 4100 cto Ram upgrade

    Hi. I have a Hp pavilion dv7 4100 cto running on windows 7 64 bit. It has 2 slots of 2 GB memory each. i currently have 2 gb of ram left since another 2 gb were broken. I would like to upgrade to 8 gb ( 4gb each slot ). This is my Ram specification found on Hp memory selector :
     Part #: VM444AA
    DDR3 PC3-8500 • CL=7 • Unbuffered • NON-ECC • DDR3-1066 • 1.5V • 256Meg x 64 •
    I would like to put 2 of 4 Gb identical memory. Quesiton is this. Can I replace with 2 kingston 4 GB wich specification is:
    Mfr Part Number: KVR1066D3S7/4G
    Type: DDR3 SODIMM
    Capacity: 4 GB
    Speed: PC8500 1066MHz
    Size & Bit: 512M x 64
    Pins: 204pin
    ECC: No
    Registered: No
    CL 7, 1.5V
    Or if its not possible can u recommend another brand with the same memory that would work ?
    Thanks, nottp.

    Hi,
    This one should work:
       http://www.crucial.com/store/listparts.aspx?model=Pavilion%20dv7-4104ca&Cat=RAM
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • HP Pavilion TouchSmart 14-n013sa - RAM

    I'm thinking of buying the HP Pavilion TouchSmart 14-n013sa  but i'm reading conflicting info regarding whether the standard 4GB RAM is up-gradeable.
    Could anyone advise please?
    Cheers,
    Steve

    im not 100% on this but i think it can take up to 6gig. best ringing hp support or make a new post saying "TouchSmart 14-n013sa maximum ram??" something like that. good luck
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ "Have you tried turning it off and on again?" "and is it definitely plug in"

  • HP Pavilion 15-p077tx 16GB RAM Supported?

    Hi,
    I am HP employee and planning to buy below model.
    HP Pavilion 15-p077tx 
    As per the spec we can upgrade upto 12 GB RAM. But i would like to upgrade to 16 GB RAM. Due to buget constrain i cannot go beyond this price.
    As per the Intel spec, this process supports 16 GB RAM.
    Can you please guide me whether i can upgrade the RAM upto 16 GB?
    Thanks,
    Meera Hussain

    The model posted in this thread - http://h10025.www1.hp.com/ewfrf/wc/document?docname=c04345345&tmp_task=prodinfoCategory&cc=us&dlc=en...
    Support only 12GB as per manual. It has already 8gb in it, so adding another 4gb is the way.
    But, I have heard people getting all 16gb available for us,e even though their specs say max 12gb as yours. But I cannot confirm it.
    The other thread you referred to is also replied by me, the manual for that model is not available to me - but it has 2 slots with one slot already with 4gb, so I assume another 4gb RAM with identical config can surely be put.
    Regards,
    ++Please click KUDOS / White thumb to say thanks
    ++Please click ACCEPT AS SOLUTION to help others, find this solution faster
    **I'm a Volunteer, I do not work for HP**

  • HP Pavilion 15-AB045ND max ram?

    Hey I am planning to buy a HP Pavilion 15-ab045nd for my study but I would like to know what the max ram capacity is before ordering the laptop. I hope you guys can help me!

    It comes with 8 gigs and would likely take 16 but these days laptops are built so it is not easy to access the memory. In your case the whole motherboard would have to be removed to get at the memory slots, best case and it would jeopardize the warranty. If 8 gigs is not enough for you, then you need to configure another system for your use. I will say that it is a very rare computer user who needs more than 8 gigs. I just gave up a laptop with 16 gigs to get a smaller machine that has 8 gigs and I do not miss the extra RAM at all and I am a pretty heavy user. That model you ask about otherwise has very strong specs for a good price. 

  • HP ENVY TS m6 Sleekbook dedicated video ram

    Hello, I have an HP Envy TS m6 Sleekbook (Product number E0K41UA#ABA) with 16gb memory that I installed.  I would like to change my settings to dedicate some memory (either 512 or 1024mb) strictly to video in order to play a high quality game.  So far I have been unable to find a way to do this, either through my regular settings or Bios.  Is this possible on my computer, and if so, how would I go about it?  thank you!

    Your GPU has its own ram , and thus it cannot be changed by any means.

Maybe you are looking for

  • Suddenly can't connect to certain websites

    This week I discovered that I am unable to connect to several websites I am accustomed to visiting frequently. These are not 404 errors. Safari and Firefox both give me the message that they "can't connect to the server," and Netscape says the "conne

  • Clone stamp & eraser have a mind of their own!

    I have recently moved from CS2 up to CS5, and am loving all the changes, however the last few days I have been in all sorts of trouble with the following issue. When using the clone stamp, or eraser, or even a brush , the cursor keeps jumping half a

  • 1300 wireless bridge secured data traffic encryption --high

       Hi All, I am looking secured encrypt configuration for the 1300 bridge wireless network . i have below configuration please suggest any change or modification on the configuration . network topology R1--------------SW1<-----------------> root brid

  • Entire itunes library is duplicated on my hard drive.  how do i fix it????

    after my hard drive crashed, i had to copy my entire library over to a new drive. in doing so, i ended up with duplicate files of most of my music. so, for example, on my hard drive (not in itunes)i have "don't funk with my heart" next to "don't funk

  • Userexit/BADI change Overdelivery Tolerance Limit in Purchase Order / MIGO

    Hi, i woould like to implement a own logic to set the Overdelivery Tolerance Limit in the order or MIGO. IIs there any badi/exit where I can do this? I tried with the exit EXIT_SAPLEINR_001 but it doesn't work. Thx Cheers Hannes