Pavilion slimline light come on but no signal on monitor

the monitor is fine for sure but it says no signal when I turn on my pc. The hard drive don't run I think either as the orange light don't flash nor do I hear it running. Only the fan runs. The keyboard light only flashes at the point when I push the power button. I use the monitor on other pc and it work fine. I can eject the DVD drive tho while the light power light is on. What's wrong, please help!!
This question was solved.
View Solution.

A lot of hp slimline main board were manufactured with a defect. Hp have extended watenty on these models that they have listed. I spoke to several online techs that eventrually deemed my pc as having such problem due to the problems that I described and the results of all the routine trouble shoot procedures that they asked me to carry out. There is a particular link that describes the situation, and that they have extended the waranty period for such models till dec 09. I got them send me a return box for me to get the part replaced. Pretty neet afterall. I can't post the link because I'm using my iPhone therefore can't copy the link.

Similar Messages

  • My Mac Mini was not sending a signal to the monitor. I powered down using the power button and now it will not start. When i power up I get a strange 2 tone sound, like a warning alarm. The fan starts, and the light comes on, but no screen

    My Mac Mini was not sending a signal to the monitor. I powered down using the power button and now it will not start. When i power up I get a strange 2 tone sound, like a warning alarm. The fan starts, and the light comes on, but no screen.
    I have tried with a wired USB keyboard and mouse using a single screen. Powered up with option pressed. No change.
    Reset SMC  no change

    Run the Apple hardware test to see what it tells you. Run the extended test when prompted, which can take awhile.

  • Pavilion G2-b27SA Laptop Won't Boot - Fan Whirs and Hard Disk Light Comes On but Nothing Else

    Hi
    My Pavilion G2-b27SA laptop won't boot. The fan whirs, the hard disk and wirless lights come on but nothing happens on-screen and the fan goes quiet after a couple of seconds (to a low whir).
    I've gone through and tried the solutions in this thread - http://h30434.www3.hp.com/t5/Notebook-Hardware-e-g​-Windows-8/Laptop-will-not-turn-on/td-p/102825 - with no luck. Specifically, I've tried a hard reset and hitting F10 when the laptop tries to boot. Neither has had any effect.
    Is there anything else I can try to get the computer working again? If I take it to a laptop repair shop (I'm out of warranty) will they be able to do anything, or is it effectively dead now? 
    Thanks in advance for your help.

    The laptop can always be fixed if you have a bottomless wallet. On a no-start with flashing lights it is likely the motherboard and a motherboard replacement if you have the shop buy the board and bill you for labor will be about $300 give or take 25%. Before we give up, it could be bad memory or a few other less expensive things. Assuming they do not charge too much just to diagnose it; take it to the shop.

  • HT3964 my built-in isight camera will still not work on my macbook pro after completing smc reset.  The green light comes on but no video.

    my built-in isight camera will still not work on my macbook pro after completing smc reset.  The green light comes on but no video. 
    Any Suggestions?

    Restart the computer.

  • Power surge mac mini power light comes on but no video

    after a power surge my mac mini 2010 2.63 ghz intel duel core processor 8mb ram 320GB onboard hard drive 2 2T external hard drives powering 2 21inch monitors.
    power light comes on but no video

    "Failure to chime" is not one problem.
    ¿ Is the power light flashing? This indicates not enough working RAM to Chime and Start up.
    Without the Chime, you get nowhere. The conventional way to debug this situation is to remove everything that could be drawing too much power and build back up from there.
    Remove AC power.
    Press the power-on button and hold for a quarter minute. (This does an SMC Reset.)
    remove all drives,
    remove all but one unit (a pair on older Mac Pros) of RAM
    Remove the graphics card, and all PCIe cards.
    Restore AC power, wait a quarter minute, then power on.
    ¿Chime?
    --Yes, add the graphics card only and proceed to debug.
    --No. if the fans are spinning, check the Voltages at a power connector such as a DVD drive connection.

  • My p6320y will not come on. The power light comes on but thats all

    my p6320y will not come on. The power light comes on but thats all. Is it the CPU or motherboard? Whichever it is what do you recommend to replace it with

    Can you get into the BIOS?  Do the HD and DVD drive show up in the main menu?
    I am a volunteer. I am not an HP employee.
    To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
    The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
    (2) HP DV7t i7 3160QM 2.3Ghz 8GB
    HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
    Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Both Customs use Rosewill Blackhawk case.
    Printer -- HP OfficeJet Pro 8600 Plus

  • My iPod classic wont connect to the computer. The light comes on but it doesn't even come up with 'connected' screen. Have tried everything on apple troubleshoot but hasn't helped. Still works in Logitech iPod player. Any suggestions please???

    My iPod classic wont connect to the computer. The light comes on but it doesn't even come up with 'connected' screen on the ipod. Have tried different computers, usb cables and ports, as well as restarting computer, updating itunes, and rebooting ipod. Still works in Logitech iPod player, however it has just wiped itself of all songs so at the moment I'm stuck with a useless iPod. Any suggestions please???

    If you happen to have a USB docking cable that is new (or close to being new), try using that one.  If the cause is the dock connector on the iPod becoming worn, if you try it with a cable that is not worn, it's possible that it may connect for data.
    I believe the dock connector is internally part of the logic board, so it may not be economical to have a repair shop (including Apple Store Genius Bar) do the repair.  You'll need to ask for pricing. 
    If you are good at such things, this web site has DIY repair guides
    http://www.ifixit.com/Device/iPod_Original
    If it's the most recent iPod classic, it appears to be quite difficult to pry open.  I have an older 4th gen (and 3rd gen) "classic" iPod, and those are fairly eash to pry open, using the plastic tools.

  • Pavilion Slimline s7700e Display brightens but is blank when waking from sleep.

    When the computer wakes from sleep it seems to come up normally but the screen doesn't work. It brightens and there is a line across the top of the screen but it doesn't show anything. If I shut the computer down by holding the power button in and start it up again everything comes up normally.
    I have recently assumed care of this computer. In investigating this problem I found that the computer had never been updated. Have since installed all Vista updates. Went to HP site and installed updates (including BIOS), changed power options and am still having the problem.
    Do not know what else to do.
    Would appreciate any ideas.
    Thank you

    Hello BrotherLouis,
    Welcome to the Forums!  
    I saw your post about the monitor on your HP Pavilion Slimline s7700e CTO Desktop PC showing a line across the top of the screen when it wakes up from sleep mode. I am going to recommend looking at the troubleshooting guides I have located for you below. The first link is specific to your exact issue and the second is covering all Display Quality Issues for the monitor.
    Solid horizontal or vertical red, green, or blue line
    Display Quality Issues
    I hope this helps you!
    Regards, 
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • I have a mac book pro.  It is 3 years old.  when I push the button to turn on the computer, it does not start.  The little light comes on, but the computer does not start up

    I have a macbook pro.  It is three years old.  It has been working perfectly fine.  However, as of yesterday, whenever I push the "on" button, the computer does not turn on.  The little light comes on indicating that the computer has started, but there is nothing on the computer screen, and it does not make the usually noise that it makes when it cycles on. 
    Any suggestions?

    Check the battery status to make sure it has a full charge (and that the charger is working). Then make sure the screen backlight is turned up.
    If the backlight is up then, try forcing the machine to shutdown (hold the power button for 5 - 10 seconds).  Then restart the computer(listen for the start up chime).
    If the computer does start up and you still cannot see anything reset the PRAM by forcing the machine to shut down (hold power button as before), then press the power button and start holding the key combo
    <Command>+<Option>+p+r
    until you hear the start up chime two or three times, then release the keys and allow to boot

  • Lights come on but not booting up.

    I have a HP Probook 6455b. When I press the power button all lights come on the caps lock and number lock blinks 5 times then stops. The screen is black and I don't hear anything unless I leave it on for a few minutes I will hear the fan then laptop will cut off after a short period of time. I have tried using an external monitor, nothing. I have tried the hard reset by unplugging the AC adapter, taking out the battery, and holding down the power button for up to 2 minutes and still nothing. Lastly I put in a brand new battery to no avail. Is there anything left for me to do before calling it quits?

    Doesn't sound good:
    http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c01732674&DocLang=en&docLocale=en_US&jumpid=...
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • Pavilion Slimline 400-034 Windows 8 not detecting 2nd Monitor

    Hello, I have a Windows HP computer, and I recently bought a 2nd monitor for my birthday, link click here. I have the same monitor for my first, and that works perfectly fine, when I bought the 2nd monitor, I realized I have a different port, and it's not a DVI-I, it's a DVI-D. So I bought a VGA to DVI-D connector, so I plugged my VGA into the connector and then plug the DVI-D into the tower. I turned on my computer, and the 2nd monitor wasn't detected, the DVI-D connected one, but the first one was. The monitor was set into mode auto, so it detected any working inputs, DVI, VGA, HDMI, and another. The 2nd monitor works thought while into the DVI-I port, but neither work in the DVI-D port. Any help (: ??

    Here are the specs for you HP Pavilion Slimline 400-034 Desktop Computer and here is the user guide for your Insignia™ - 24" LED HD "NS-24EM51A14" Monitors. Based on the specs of your computer, it has one DVI-D (digital only) output and one DVI-I (digital and analog) output as shown below;
    #3 - DVI-D (digital only)                     #4 - DVI-I (digital and analog)
    According the user guide for your Insignia monitors... VGA, DVI-D, and HMDI inputs are available. Using a passive DVI-to-VGA adapter will work on the DVI-I port because it supplies both digital and analog signals. Using a passive DVI-to-VGA adapter will NOT work on the DVI-D port because it only supplies digital signals. Please remove both DVI-to-VGA adapters and VGA cables and replace them both with DVI-D cables. You can purchase these cables online and at most local retail store such as Fry's, Best Buy, Walmart, Target, Radio Shack, Staples, Newegg, Office Depot, etc. Once you have purchased two DVI-D cables, please connect your hardware as follows;
    Computer ---> DVI-D cable ---> Monitor #1
    Computer ---> DVI-D cable ---> Monitor #2
    If you have any further questions, please don't hesitate to ask.
    Please click the White KUDOS "Thumbs Up" to show your appreciation
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

  • PC turns on but no signal on monitor? 970 Gaming Motherboard

    So i just upgraded my pc
    Corsair Force LX Series 128GB SSD (new)
    XFX R9 280x
    Seagate 1TB HDD (new)
    MSI 970 Gaming MOBO (new)
    16GB Ram
    Windows 8.1 OS (new)
    Rosewill ARC M550 550W PSU (new)
    So basically when i turn on my pc, all fans are on and the mobo lights up. But the monitor just stays black! So what i do is just hold the power button to turn it off and try to turn it on again. Now this is the weird part... sometimes it turns on and sometimes it doesnt. Sometimes i need to turn off/on for 3 or 4 times for it to turn on. Sometimes i need to do it just once. Its so inconsistence and strange.
    Example:
    One day i was just playing a game and suddenly my monitor turns off. The thing is the fans and all is still working. I thought it was the GPU but the fans on the gpu is still on!
    My hunch is on the SSD, which holds the OS. But im not sure, could it be the motherboard? My GPU maybe?

    So before all this happen, i have a similar setup with different brand of motherboard and PSU. All i bought is a new brand of psu and mobo and i add an SSD. the thing is, i use to have an antec 550w before and my pc just ran fine, no crashes what so over and no problem on boot. But i dont have an ssd back then.
    my ram is set to clock speed 1333
    i dont think my pc crash, if it did shouldnt my whole pc turns off including all the fans and all? When i was playing the game, my monitor turns black saying no signal but my pc fans, including GPU's fan is running. I have this problem too on boot. When i try to turn on my pc, the pc it self is running (including GPU's fan) but monitor doesnt recieve signals. I have to turn on/off 3-4 times for it to turn on properly. Sometimes it turns on the first time, and sometimes not, its so insistence and strange
    If it is my psu, what wattage should it be? Any suggestion that wouldn't break the bank?
    I dont think my PC overheats. I have an aftermarket air cooler on my cpu and i have 4 120mm corsair fans running on my carbide air 540. and if it did crash, shouldnt my whole pc turns off? only the display is not getting signals, all my pc components's fan/light is on.

  • My Apple TV light is on but no signal from TV

    Hi There,
    Everything is plugged in properly but and the I put on my TV is correct but there is no signal.   How do I setup my Apple TV?  My router is across the room.

    Which TV are you using? Are you connecting via HDMI? Is it secure? Have you tried a different cable? Different port? Made sure that you've navigated to the correct input on your TV?

  • HP 5440 deskjet resume light comes on, but printer won't print

    I have a hp deskjet 5440 photo printer, but as of a day or so ago, it won't print. I've re-downloaded the driver, bought a new usb cable, checked all the things on the troubleshooting page that comes up when the print job finally gives me an error.  When I turn the printer off and back on, the resume button comes on and flashes until I push it, but other than that I get no response from the printer. My computer is running Windows XP, but I also hooked it up to my laptop which is running Windows 7, and it won't work there either.
    Any ideas on something else to try?

    Hi there,
    This article should cover the issue you are experiencing. Give the steps outlined a shot and let us know if it helps.
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Satalite Pro Power lights come on but nothing else ??

    Hello All,
    A quick question. Have been given a Satalite Pro. The Power lights up but nothing else.
    I've tried the HDD in my Portege m200 and its running XP Pro. The Satalite Pro has 1 > 512 ram stick inside.
    The overall condition is good and i'm tempted to spend a few shillings to try and bring it back to life or are we talking major surgery.
    My knowledge is basic so would have to pass on to get fixed.
    Would welcome your thoughts / suggestions.
    Thanks
    Neil

    Hi
    I dont know which Satellite Pro you have exactly but if your Portege M200 uses the same RAM modules, you should try this to exchange them. Sometimes the notebook doesnt start due faulty RAM modules. They are exchanged in few minutes and not expensive.
    I doubt that the HDD would be the problem. If the HDD doesnt work, you able to access the BIOS at least.
    In worst case its related to other expensive parts like CPU or mainboard. :(

Maybe you are looking for