Pavillion G7-2233cl clone HDD to SSD?

Have a HP G7-2233cl laptop, running Win8x64. Came with a 640Gb HDD, I have a 360Gb SSD I wish to replace the HDD with.
Macrium Reflect Free show there are 5 partitions on the HDD:
1- WINRE (no drive letter) NTFS Primary 235mb out of 400mb used
2- NO NAME (no drive letter) FAT32 (LBA) Primary 88.5mb of 260mb used
3-(no drive letter) unformatted primary 128mb
4- C: NTFS Primary 52Gb of 570Gb used
5-RECOVERY D: NTFS Primary 21.5mb of 24mb used.
If I just clone the C: & D: to the SSD will the laptop boot? Any ideas what the 1 thru 3 partitions are
for?
Also can I use the recovery disks I created to restore to the SSD if I just swap the drives? Will the recovery disck work with the SSD being smaller (360Gb vrs 640Gb) the the HDD was?
Sam

I understand that you are curious about partitions 1-3 and if the system will boot with just C and D.
Unless the used space is larger than what is available on the SSD, most cloning software are capable of taking partitions from a larger disk and placing them on a smaller SSD.  Partition looks like it is the boot partition for the HP recovery based on the size.  If you plan to use the recovery in the future, I would leave it intact.  The recovery drive, D, looks like it is too small as it is usually around 20 GB.  Partition number 2 looks like it would be the Windows 8 boot partition.  Partition number 3 doesn't appear to be used at all since it is unformatted.  
As long as you keep the original drive in its original state, you should be able to recopy the partitions should you need them.  From the description of the partitions, it sounds like all partitions but partition 3 are needed.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Similar Messages

  • Clone hdd with windows 8 to ssd

    HI, I've purchased a hp envy phoenix h8-1580d with windows 8 pre-installed on 25 july. Since then I've tried many ways to clone the system disk to an INTEL 330 120gb SSD but failed. At last, I decided to clean install the windows 7 Pro to the SSD, but the computer could not boot from the DVD, FAILED AGAIN. I would be very grateful if any expert here could provide any solution to solve this issue. My sincere thank in advance.
    Anyway, I did contact the hp technical support and they took 2 days to work out a solution and they failed too.

    Finally suceeded in cloning the HDD to SSD with EaseUS Todo Backup Free 6.0.

  • Changing HDD to SSD, what are the options?

    hi, guys, new to the forum, I just bought a thinkpad x130e during an on sale event at one of the local retailer, pretty excited, since i like the rugged design.
    I am looking at an upgrade from 320G HDD to a 128G SSD... but i don't have any windows 7 installation disc handy, so what are the options for me to install the operating system (windows 7).
    I don't know if there is a way to transfer the whole system from HDD to SSD? will there be any trick to perform? or simply i just have to purchase new copy of windows?
    cos i noticed i do have a windows7 pro product key at the bottom of my thinkpad, i kinda don't want to waste the money.
    please help..
    Solved!
    Go to Solution.

    You don't need to purchase another copy of Win7. You will need
    1. SSD. This must be 7mm thick, not the more common 9.5mm thick.
    2. USB enclosure for your HDD,
    3. Software to "clone" the contents of your HDD to your SSD. Acronis True Image is a well-regarded package that does this. There are also some free utilities that can do this, however, I'm not familiar with them.
    Procedure:
    1. Move the HDD to the external enclosure.
    2. Put the SSD in the X130e.
    3. Reboot from the HDD. (You'll need to interrupt boot with Blue ThinkVantage button to specify.)
    4. Install Acronis (or equivalent.)
    5. Perform disk clone operation. You will need to tell the software how you want to resize partitions since you're going to a smaller disk.
    6. Reboot from SSD.
    Cheers... Dorian Hausman
    X1C2, TPT2, T430s, SL500, X61s, T60p, A21p, 770, 760ED... 5160, 5150... S360/30

  • Going from hdd to ssd

    I would like to change a hdd to ssd on macbook pro (mid 2010). If I use time machine backup from old system on new ssd will it be copied with the old disk faults ? I would like to install fresh OS X on ssd, but at the same time I wish to keep aperture librery with all my pictures and iweb where I created my website.
    This are my priorities and the rest of data I can move to external hard drive and bring them one by one to new system on new ssd.
    Could you please, tell me how to do it and what is best solution ?

    A clone of a HDD will have loads of empty blocks, all those blocks would be written to the SSD...
    Incorrect.  Most backup programs don't do a block-for-block copy (though some have such an option on very restricted conditions).  They copy the files (like cp -rp).  So blank space on the source won't be the same blank space on the destination. 
    But serious question for a moment, do these Carbon Copy Clone drive 3rd party softwares have some kind of special function? Some people have crazy devotion to them and its peaked my interest as to why.
    If you want to go through the "exercise" of creating lauchagents or cron tasks for constructing and easily changing scheduling backups, more power to you.  I for one just want to schedule the stuff, possibly change the schedule if need be, and move on to more important things like doing the work that actually needs to be backed up!   If you don't believe in scheduling periodic backups, well, that's another story.
    Though, to be honest, I still question its usefulness when Disk utility does the same thing; select a hard disk ( "TOSHIBA MK2561GSYN Media" on my MacBook Pro), click "new image" and then click go. Then use restore in Disk Ulitity to restore the disk from the image - carbon copy goodness!
    So do most other people that do backups, i.e., creating a .dmg (what you get from DU's New Image) is not the way to do backups.  DU's Restore, maybe, but I've never used DU for backups.

  • Cloning Hdd to SSD boot drive and what happens with Music/Logic Plugins

    Hi, my computer is a mid-2012 Mac Pro 12 Core
    It's a great computer but I'm considering upgrading my main boot drive (WD Caviar Black 1TB HDD) to a 1tB Samsung EVO 840 SSD drive (I'm using a sonnet tempo PCI card to mount an SSD that holds audio at the moment and will add another SSD for the boot drive I'm referring to) so I just had a question - if I clone the HDD to the new SSD, what happens with things like licenses for my audio plugins, such as Native Instruments Komplete, programs by IKMultemedia. programs that use an ILOK such as Steven Slate Plugins and also, WAVES plugins?  Will this info all carry across to the new SSD drive or do you think I'll need to reauthorise some things?  I have all the serials etc so this shouldn't be an issue, but just wondered.
    Any help would be appreciated as it feels like quite a big step in that it's my main system drive!
    Thanks in advance
    Sam

    CCC is excellent. If it doesn't work then sure, just always have a safety net of your system that is untouched.
    Also, after a clean install, CLONE it!
    And then use Setup Assistant. Migration Assistant.
    Clone of the system can go on sparse disk images too so you don't have to partition (should have at least one though) and you can have clone from different stages and versions: 10.9.4, without Setup Assistant, migrated, full loaded with all your apps. Multiple versions.
    CCC is designed to make a working bootable copy of a system so you can move the system to another boot device like hdd and SSDs without the worry.
    But I think we were talking about a system that did not see a clean install of Mountain Lion or Mavericks so it is over due for one!

  • Upgrade HDD to SSD (Do i need to re-install?)

    I just bought an SSD (Samsung 470 series is the one thats best with MBP right?) and i want to replace it with the stock HDD that came with my 2011 MBP 13".
    What if i upgrade RAM from 4GB to 8GB and transfer from HDD to SSD by carbon copy cloner. Do i need to re-install Lion then?
    Is TRIM automatically enabled if i transfer from HDD to SSD?

    Upgrading the RAM is fine by itself. Just know you only have two slots, and thus need matching pairs of 4GB modules to increase the RAM from 4GB to 8GB. If you have $900, OtherWorld Computing has 16GB of RAM (two 8GB modules) for sale. (no compensation)
    Use the online Crucial checker and MacTracker to make sure your getting the correct specs of the RAM (and the amount of modules) before purchasing.
    What you need to do is use the free to use (donations accepted) Carbon Copy Cloner on the HDD while it's still in the machine, clone to a external powered drive and hold option to boot from it, test it out that it works.
    Then make the HDD to SSD switch and option boot from the clone again, format the SSD HFS+ Journaled and use CCC to clone it onto the SSD.
    OtherWorld Computing and iFixit has videos, pictures, instructions and tools needed.
    When you clone, it clones the OS X partition only, not both your OS X partition and the Lion Recovery Partition, which in your case is unnecessary to have if you have a "hold option" bootable clone. (should keep two at times)
    If you need to download Lion installer again, simply use MacAppStore and hold option and click on Purchases, either in Lion or Snow Leopard and then make a couple of " hold c" bootable DVD's from these instructions.
    http://www.eggfreckles.net/notes/burning-a-lion-boot-disc/
    These DVD's made from these instructions contain the full OS X Lion, not a Recovery Lion disk or the Lion Recovery Partition which Apple provides a download for and requires a lengthily Internet connection to download Lion before it's installed.
    Far as setting the TRIM, I don't know about that. Hopefully someone else will answer.
    If not ask Dave (Bmer) over here:
    http://macosg.com/
    He replaced his hard drive with a OCZ Vertex, the fastest SSD's on the planet and also his Superdrive with a 7,200 RPM 750GB drive for storage (note: you can't boot from a Lion/Snow/Windows DVD from a external optical drive) so he would know best what to do.
    Also OCZ just came out with a 480 gb or so very fast SSD, the Vertex 3 series, just as fast as the smaller SSD's but with more storage capacity, so that would be worth checking into. (smaller SSD's are faster, larger older ones are just a bit faster than a regular hard drive)
    Also check out your Mac model's SATA number using the fre MacTracker and System Profiler, this way you can by the right SSD for the price and know your bus speed limitation accessing the SSD.
    Good luck.

  • HP ENVY 17T - J100 I NED TO REPLACE THE MAIN HDD TO SSD

    I was just wanting to confirm that with the HP ENVY 17T J100 model can upgrade it's HDD to SSD? This model has the 1TB HDD. If I simply clone the HDD to an SSD of the same size.  will it work? Or is there more complex setup to get the raid working between SSD/SSD rather than SSD/HDD?
     also i try with 120 ssd and it didnt work. if i change the main 1 TB HDD to 1 tb SSd can i use the recovery disks to return all the windows as factory with the SSD or not and why if not
    Thanks for your time!

    Hi @sherifmadkour
    I understand you are looking at replacing your HDDs in your notebook with SSDs. I can help you with your question.
    Please see the following for your notebook family which shows the supported components.
    HP ENVY 17 Notebook PC HP ENVY TouchSmart m7 Notebook PC HP ENVY TouchSmart 17 Notebook PC Maintenan...
    You can find the drive list in the product description section,  and also under the Hard Drive list, in Component replacement procedures.
    Anything outside of that list would not have been tested with the other hardware, and so is unexplored territory. It is one of those things where if a device has different current requirements, it can put strain on the other hardware or an issue of driver compatibility.
    Malygris1
    I work on behalf of HP
    Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
    Click Kudos Thumbs Up on the right to say “Thanks” for helping!

  • Going from HDD to SSD+HDD

    I have a 2010 First Gen i7 desktop iMac computer and am looking rather fondly at SSD drives to run alongside my 1TB Internal HDD. Boot and Apps on SSD, everything else on Internal, the usual set-up.
    I know I can change the location of my home folder via System Prefs > Users & Groups > Ctrl+Click User > Advanced Options
    What would be the best way to deal with the migration from HDD to SSD+HDD?
    Do I do a fresh install onto the SSD and then point to the home folder left over on the HDD and delete the old system files around it?
    Does restoring from Time Machine via the Lion install process give me the option of choosing a different disk to send my personal files to? (this would be proffered).
    Do I wipe everything clean, restore the OS from time machine, then use Time Machine from the temperary user account to restore my personal files to the HDD?
    I do have two external HDDs (time machine and "junk" drive) - do I use the terminal to copy my files to the junk drive (preserving structure and timestamps using the -pR flag), then copy them back onto the HDD once everything is wiped and continue from there?
    The last options seems like the most realistic, but the second would be the most proffered (if possible).
    What is the best way to do this? Anyone done it before? Anything I should be careful of?
    Thanks!

    A clone of a HDD will have loads of empty blocks, all those blocks would be written to the SSD...
    Incorrect.  Most backup programs don't do a block-for-block copy (though some have such an option on very restricted conditions).  They copy the files (like cp -rp).  So blank space on the source won't be the same blank space on the destination. 
    But serious question for a moment, do these Carbon Copy Clone drive 3rd party softwares have some kind of special function? Some people have crazy devotion to them and its peaked my interest as to why.
    If you want to go through the "exercise" of creating lauchagents or cron tasks for constructing and easily changing scheduling backups, more power to you.  I for one just want to schedule the stuff, possibly change the schedule if need be, and move on to more important things like doing the work that actually needs to be backed up!   If you don't believe in scheduling periodic backups, well, that's another story.
    Though, to be honest, I still question its usefulness when Disk utility does the same thing; select a hard disk ( "TOSHIBA MK2561GSYN Media" on my MacBook Pro), click "new image" and then click go. Then use restore in Disk Ulitity to restore the disk from the image - carbon copy goodness!
    So do most other people that do backups, i.e., creating a .dmg (what you get from DU's New Image) is not the way to do backups.  DU's Restore, maybe, but I've never used DU for backups.

  • Plz upload a video on how to upgrade a traditional HDD to SSD on lenovo t61

    can someone plz upload a video showing how to upgrade a traditional HDD to SSD on lenovo t61, help appreciated thanks
    Solved!
    Go to Solution.

    Hi ghattiya,
    Removing and replacing the HDD, assuming the same form factor, is shown in the Lenovo Training Videos.
    For tips on how to clone the drive or do a clean install, I suggest starting by searching the forum.
    I don't work for Lenovo. I'm a crazy volunteer!

  • Moving Windows 8.1 from HDD to SSD

    Hi! I want to know the best way to move Windows 8.1 from current HDD to SSD. Thanks!
    System Information
    Model:  MSI GT72 2QE DOMINATOR PRO GT722QE-638NL
    Product Name:                 GT72 2QE
    OS:                           Microsoft Windows 8.1 64-bit
    Windows Product Key:         
    HDI Build:                    ZS7-1781BM4-DS0   3.3.A15.8.0.1 
    BIOS Version:                 E1781IMS.10H
    BIOS Release Date:            2014/11/21
    EC Version:                   1781EMS1 Ver5.08, 11/04/2014
    CPU:                          Intel(R) Core(TM) i7-4720HQ CPU @ 2.60GHz
    Memory:                       16 GB @ 666 MHz
                                   - 8192 MB, DDR3-1600, Kingston MSI16D3LS1MNG/8G 
                                   - 4096 MB, DDR3-1333, Samsung M471B5273DH0-CH9 
                                   - 4096 MB, DDR3-1333, Samsung M471B5273DH0-CH9 
    Graphics:                     NVIDIA GeForce GTX 980M, 4095 MB
    VBIOS Version:                84.04.22.00.0c
    Drive:                        HDD, HGST HTS721010A9E630, 931,51 GB
    Drive:                        SSD, ADATA SP900NS38, 238,47 GB
    Network:                      Killer Wireless-n/a/ac 1525 Wireless Network Adapter
    Network:                      Killer e2200 Gigabit Ethernet Controller (NDIS 6.30)
    OS Activation
    Name: Windows(R), Core edition
    Description: Windows(R) Operating System, OEM_DM channel
    Partial Product Key:
    License Status: Licensed

    Thank you all for answers. I found a solution:
    Tools: 1) Aomei Partition Assistant Pro Edition
             2) Paragon Migrate OS to SSD 4.0 ™
    First i convert my new SSD MBR to GPT with AOMEI Partition Assistant. After this used Paragon Migrate OS to SSD™ 4.0. Very easy. Time ellapsed ca 30 minutes.
    w w w.paragon-software.com/technologies/components/migrate-OS-to-SSD/
    w w w.download.paragon-software.com/doc/MigrateOStoSSD_4_manual_eng.pdf
    w w w.tomshardware.co.uk/forum/id-1670056/successful-clone-windows-hard-drive-ssd-gpt-uefi.html

  • I want to change my HDD to SSD for macbook pro 15 2010 need some help

    i want to change my HDD to SSD what will work with my macbook pro 2.66GHz (15-inch Unibody w/Intel Core i7) - April 2010 and do it will make my macbook pro low timp and do my macbook pro will be more faster ?

    Personally I am not a fan of SSDs because they are not cost effective for my personal requirements.  However I do recognize that the days of the disk are numbered, but I suspect that day is still a few years off.
    Crucial is a fine company and is one of the two I personally recommend for RAM (OWC being the other) so I suspect that would be a good choice to make.  They are a consumer responsive company.  Indeed the Amazon price is attractive but before you commit yourself, see if you can find test information and reviews on this product.
    I personally cannot give you first hand information on SSDs because I have none of my own.  But perhaps some one will read this post and chime in.
    Ciao.

  • How to upgrade from HDD to SSD in Mid 2010 13inch MacbookPro?

    I am upgrading from HDD to SSD and would like the step by step direction of how to do it on my 13inch MacBookPro mid 2010. Also, I would like to do a clean install of the OS onto the new SSD, and simply transfer my data(i.e. documents, pictures) from the old HDD to the new SSD(Samsung 500GB)
    Any detailed directions would be appreciated. You may send responses directly to my address: ******* Thanks in advance
    <Edited by Host>

    Tolefe1 wrote:
    Thanks. How do I booth to IR? Won't  I need to connect to the internet to be able to booth to Internet Recovery... Please give steps as I am pretty new to this.
    Turn the Mac on (or reboot it) and press command-option-R as soon as you hear the startup chime. Hold the keys down until you see a globe, then release. When the Recovery Menu appears you choose Disk Utility and format the SSD for use in a Mac (Erase>Set Format to MacOS Extended (Journaled), then exit Disk Utility and choose Install OSX
    You will need to be connected to the Internet and your Mac should detect your network and ask for a password automatically when Recovery Starts.

  • Q190 from HDD to SSD?

    Hi,
    Can I upgrade my Q190 (57312246) from HDD to SSD? 
    I am looking to purchase the following SSD: http://www.amazon.com/Samsung-MZ-7TD250BW-Series-Solid-2-5-Inch/dp/B009NHAEXE/
    Thanks
    Solved!
    Go to Solution.

    hi filippo,
    Yes you can use that SSD Samsung MZ-7TD250BW 840 Series Solid State Drive (SSD) 250 GB Sata 2.5-Inch as the Q190 uses a standard SATA 3.0Gb/s, 2.5" wide HDD as per this pdf data sheet.
    You may also want to check Crucial's SSD Upgrade for the Ideacentre Q190.
    Best regards,
    neokenchi
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Will the new 2012 iMac support 2 hard drives (HDD and SSD) like the 2011 iMac?

    Will the new 2012 iMac support 2 hard drives (HDD and SSD) like the 2011 iMac?

    Well, I'm not sure how anything can fit into a 5 mm depth, so I can see why they've removed the CD drive -  there probably wouldn't be enough room for the laser, LOL. Can't imagine speakers, hard drive (of any flavor), logic board and so on and so forth. Fortunately, my iMac has Applecare through early 2015 so I'm set for a while; I may check out a Mini at that point - saw that it is configurable with a fusion drive, which would make it interesting for me.

  • HP Pavilion dv3-4150st hdd and ssd together?

    hello,
    i have HP Pavilion dv3-4150st . can i put hdd and ssd harddisk together in my notebook?

    Hi True-Paladin,
    Thank you for your query, I will do my best to address your concerns.
    HP can only recommended tested configurations, as they know the expected result.  It is a personal choice to deviate from their recommendations in  the maintenance and service guide.  That is not to say they will not work, only that they have not been tested and therefore  results are unknown and therefore unsupported.
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Maybe you are looking for