PB won't network with G5 & emac

My wireless network consists of a G5, PB G4 and emac all connected via Airport Express.
All worked fine until I changed my Airport Express settings from WPA to WEP. Now the G5 and emac can see the PB, but the PB can't see the other two. Something weird is going on as I haven't changed the PB's network or sharing settings.
The G5 is running 10.3.6, PB 10.3.5 and emac 10.3.8.
Would upgrading to Tiger help?

Upgrading the MacOS is not a solution to a problem that "just popped up". You are just as likely to cause yourself even more headaches with an OS upgrade.
Did you try just powering down everything (all three Macs and the Airport Express), then plug in the Express (wait a minute), then restart all Macs?

Similar Messages

10.5 won't network with Palm PDA device

Despite enabling SMB file sharing and doing everything else I could think of to continue using my Palm PDA to access and copy files on and from my Imac desktop, I found that my file sharing utility on the Palm (WiFile Pro 2.12) which had worked fine under OS 10.4 simply can' seem to access any more my MAc hard drive. I had been using wi-fi to connect the Palm device into my router for the Mac.
Now when I try to connect I keep getting indications from the Palm device that the MAC file system was closed to my attempts to connect.
QUESTION: Has anyone any advice on a new shareware r other software that will enable current Palm handheld devices to network for file sharing with a desktop Mac using one's existing wi-fi setup in the home environment.

Hi,
I haven't managed to get smb to work, but I have got an ftp connection through my Airport Express. See my reply to Michael K Murray Re: wifile pro - smb problem.
For transferring files between the two, plain Bluetooth send works.

G5 Quad 10.4.10 won't network with G3 OS 10.2.8

I'm attempting to transfer a huge file from a G3 laptaop running OS 10.2.8 over to a G5 Quad running OS 10.4.10. I've tried Target Disk and file sharing, to no avail. Any suggestions?

I copied the video onto a dvd and transferred it to the G5 (deadlines).

I just installed Airport Extreme. It works as a wireless network on my Macbook. It won't connect with my Windows Visa PC. Message reads: "settings saved on this computer for the network don't match requirements of the network.

I just installed Airport Extreme. It works as a wireless network on my Macbook. It won't connect with my Windows Visa PC. Message reads: "settings saved on this computer for the network don't match requirements of the network." I seem to need to enter a security key/passphrase to connect to the PC. Where do I find them?
Thanks for your help.

I assume that you have Wireless Security enabled on your AirPort's wireless network. The issue maybe that the PC is unable to use the WPA password itself and will require using the Equivalent Network Password instead.
To get this password, you will use the AirPort Utility from the MacBook:
Start the AirPort Utility > Select the AirPort base station > Manual Setup
Now, before doing anything else, go up to the utility's menu bar at the top of the screen, and then, choose "Base Station," and then, Equivalent Network Password from the drop-down menu. You will see two items: 1) WPA Password, which should look familiar to you, and 2) WPA Pre-Shared Key. It should be a long hexidecimal set of numbers and letters. Jot down this second item.
You will want to use the value you just jotted down when entering the password from the Windows Visa PC.

How can I extend the range of an Extreme network with Express when my mac won't find the Express???

Cable modem. Properly working Apt Extreme router (g), but inadequate range to upstairs home office. I want to entend with an Apt Express and have a networked USB printer working off the Express unit placed in my office. Mac mini running Lion can't/won't find the Express.
Can you help me? Thanks in advance.
SULLOQUY

If you were able to access the AX using the AirPort Utility but your PC is still not able to connect. I would try performing a "factory default" reset on the AX to see if that helps before going to the store. This type of reset will put the AX back to its "out-of-the-box" configuration which would broadcast an unsecured wireless network with a network name of something like: Apple Network NNNNNN. If your PC still cannot "see" or connect to this network, then a visit to the store would be in order.

IPad2 won't sync with iMac...only my iphone4 shows in the device window on my iMac. For some reason it will not detect my iPad via my wireless network!

iPad2 won't sync with iMac and only my iphone4 shows in the devices window on my iMac. For some reason it will not detect my iPad via my wireless network! The iPad will sync when plugged into the Mac however looses connection and disappears from the device window when unplugged.

Jayplus wrote:
I have a D-Link WBR-2310 and already bought an external antenna which cost me additional. Besides moving my iMac, what options do I have?
You already have a wireless router or have just bought one, or do you have an ad hoc connection from iMac to AppleTV?
If things worked in the other location this all point to poor network performance/connectivity. It may be the connection is intermittently lost - small files transfer ok, but interruptions during longer transfers scupper the process.
Interference from cordless phone bases or microwaves (and neighbours devices) might also cause connectivity issues.
Signal strength bars are often not that useful, but will indicate connection to the main wireless device they connect to - so AppleTv may have a good connection to the router but a poor iMac connection to router is not displayed by AppleTV which only shows the connection to the first device in the chain.
You could consider some home mains newtorking plugs such as those made by Devolo but they usually have to be on the same mains ring.

Airport express won't work with Extend Network, only Create Network

My Airport Express when it is setup to extend my network while plugged into Ethernet will Create a network under settings. If I change this to Extend A Network it doesn't work properly. It keeps kicking me on and off WiFi, but the former way works with no foreseen issues. What is going on? I can't extend my guest network with the first option, I don't believe.
I have a 5th Generation AirPort Extreme and a 1st Gen AirPort Express.

My Airport Express when it is setup to extend my network while plugged into Ethernet will Create a network under settings
This is the correct setting to "extend" the network using an Ethernet connection. Technically, this is called a "roaming" network.
If I change this to Extend A Network it doesn't work properly.
This is because "Extend a wireless network" is used only when AirPort devices communicate with each other using wireless only......not Ethernet.
It would help if Apple used settings like "Extend a network using Ethernet" and "Extend a network using wireless only".....but they don't.
The AirPort Extreme will need to be configured as the main router if you want it to provide a Guest Network. It cannot do this if it is configured in Bridge Mode.

Can't read or write some files, internet is failing, youtube won't load, software I tried to install was in Slovenian, not dutch or english like in my systempreferences settings, pictures and files won't preview with spacebar, etc. Malware?

Specs:
iMac 10.8.5
3,4 GHz Intel Core i7
32 GB 1600 MHz DDR3
Can't read or write some files, internet is failing, youtube won't load, security software I tried to install was in Slovenian, not dutch or english like in my systempreferences settings, pictures and files won't preview with spacebar and are randomly corrupted, when I entered something in the Youtube searchbar (when it was still working) it send me to a site with sexadds.
I tried restart my iMac and when I was logged back in, my dock preferences were reset.
Also tried to download some security software to check my Mac for malware, but when I did, I tried several, I got a notification that said something like 'dumpfiles (don't know if this is the right translation...) damaged'.
I'm taking screenshots from all the weird notifications I get and even three quarters off the screenshots I took in the last three hours are already unreadable.
It started this morning when I tried opening a Premiere Pro file on which I worked the night before.
When I tried opening it, it said the file was damaged and could not be openend.
I tried opening it with AE or importing the file in a new project but nothing helped.
When I tried looking for autosaves, this is the really weird part, there were none.
Even though there are autosaves from my other projects, this one was completely gone.
It looked like the day before never happened on my computer.
Also when I openend Premiere all the recent projects had been wiped.
So at first I thought it was a Premiere Pro failure.
But than, later on the day, I tried loading some RAW files from my compact flash card.
This is where I would get an error (error -36) which said some data cannot be read or written.
I tried importing the files with a view different technics, from dragging to importing via Lightroom and I succeeded with Image Browser.
But when I tried moving the files to an other folder the same error occurred.
While dealing with this issue I wanted to put on some soothing music on youtube.
This is when the next weird thing occurred: youtube wasn't completely loading in Chrome. I refreshed a view times, checked the internet connection and still no difference.
When I tried in Safari it did work but when I clicked enter on the searchbar in Youtube, a page with sexadds appeared (I didn't install AdBlock in Safari...).
I read about this 'phishing' where you are redirected to a site were a possible malware installment can take place...
I don't know if it's connected to any of the problems I've been having but I just never experienced this on a mac, I have been a Mac user for 10 years now.
On top of it all, internet started working worse and worse and now it's not even working at all. I had to fill in the password over and over, normally it remembers.
Just like my system preferences, all the preferences I had with Chrome where also reset.
Also somewhere in between I got this notification: Mac OS X must restore library to run programs. Type your password to allow.
To me this is all very weird and suspicious. I have clearly no idea what's going on. Could this be another sort of trojan horse or malware?
Some background info which could be helpful for solving this mystery:
two months ago the one year old Fusion Drive in my iMac just broke out of nowhere.
I got it replaced by a qualified apple repair store.
When I got my computer back, all the files where gone.
I got on the internet without AdBlock installed yet.
A game or whatever it was, can't clearly remember, got installed by accident.
I deleted it immediately.
Only two weeks later, I couldn't log in to my account. It didn't recognize my password and username.
So I brought my mac back to the store.
Here the repair guy said it was a minor thing and he just needed to reconnect my account. He also mentioned he found a downloaded game name Sparta and it probably had something to do with the error.
I asked him; could it be a virus? He replied no way.
I don't know why I couldn't be a virus, just because it's a mac doesn't mean it cannot be done.
So today I tried installing anti virus software (such as avast- was in a weird language looked like slovenian, clamxav - was in slovenian) but I couldn't install them.
PLEASE help me! I don't know what to do anymore, I work fulltime and I need my computer, I have no time to bring it in for repair, are there other perhaps easier ways?
Could this be the work of a virus or a malware? Or is it a disk permissions issue?

It sounds like you may have multiple problems, but none of them are likely to be caused by malware.
First, the internet-related issues may be related to adware or a network compromise. I tend to lean more towards the latter, based on your description of the problem. See:
http://www.adwaremedic.com/kb/baddns.php
http://www.adwaremedic.com/kb/hackedrouter.php
If investigation shows that this is not a network-specific issue, then it's probably adware. See my Adware Removal Guide for help finding and removing it. Note that you mention AdBlock as if it should have prevented this, but it's important to understand that ad blockers do not protect you against adware in any way. Neither would any kind of anti-virus software, which often doesn't detect adware.
As for the other issues, it sounds like you've got some serious corruption. I would be inclined to say it sounds like a failing drive, except it sounds like you just got it replaced. How did you get all your files back after the new drive was installed?
(Fair disclosure: I may receive compensation from links to my sites, TheSafeMac.com and AdwareMedic.com, in the form of buttons allowing for donations. Donations are not required to use my site or software.)

I have an iphone 4 that i use as an iPod. it is not connected to a telephone company. I updated to ios7 and now it won't sync with my computer

I have an iphone 4 that I use as an iPod. It is not connected to a wireless network. I have updated to the IOS 7 and now it won't sync with my computer. Does anyone know what could possibly be the problem?

Contacts are designed to be synced to a supported application on the computer or a cloud service.
Pictures taken with the device are designed to regularly be copied off the device to a computer as would be done with any digital camera.
If you have failed to use the device as designed it may be too late to recovery anything.
Is the device regularly backed up to a computer via iTunes? If so, the most recent backup (when restored to a replacement iOS device) should contain all contacts and pictures as of when the backup was created.

HT4259 I have been trying for hours to extend my Extreme Gen 5 network with an Express Gen 2. But no matter what I do or try, it doesn't work. What does happen is my internet gets block somehow when the Express looks like it's set up and 'green' - no in

I have been trying for hours to extend my Extreme Gen 5 network with an Express Gen 2. But no matter what I do or try, it doesn't work. What does happen is my internet gets blocked somehow when the Express is online and looks like it's set up perfect and 'green' - but no internet connection for anything even though the Extreme is green and the modem is good. Once I disconnect the Express, everything is good again.
I've tried LAN, WAN, though a switch, direct connect, Extreme set to Extend the network, the Express set to be an extension. Most of the time I get an error trying to update the Express. But when it seems to be set up perfect, the entire house can't get to the internet. Just when it looks right, it is so wrong.
If anyone can give me exact steps (e.g., "...from the Base Station menu, select the Restore Default Setting option" vice "...just restore the defaults..."), I would greatly appreciate it. I'm left to the conclusion that the Express is faulty. I've been using Airport Utility 6.2 from Mountain Lion on one computer and Airport Utility 5.6.1 from Snow Leopard on another computer (the latter give more control while the former just want you to 'forget' the Express).

I finally got it working. I was trying to set it up ethernet. My biggest mistake was when the new Express came on, I did not select 'Continue' - I went straight to manual thinking that I would get the most setup options in manual mode. So everything I initially tried always resulted in 'wireless'. Even when I would update or restore default settings, the Express would not completely restart. Or sometimes I would get an error. So most of the time I had to unplug it. So when it came back up, none of my changes were retained. But there were a lot of times when everything was green and appeared to be fine. But anytime the ethernet cable was plugged in, no more internet.
So here's the weird part. When I finally tried 'continue' (vice manual), I would get 4 options. One would be 'ethernet' extended. So I would select it, it gave me green lights, all looked good, and still the same problem. This is when I got frustrated. I thought I had exhausted all possible combinations.
But somehow when trying continue again after another restore, I only got 3 options. One was the same ethernet extended option (can't remember what the missing 4th one was). And this time it worked - it gave me the big green circle with the checkmark saying it was successful. I don't know what I did different, but I know now that it won't work if 4 options come up to choose from. It will work if only 3 options come up. And success if only verified by the big checkmark. Had anyone anywhere said the checkmark declaring success is validation, then maybe I wouldn't have gone down so many rabbit holes thinking it should have been successful.
As for which Airport Utility I prefer, 6.2 looks nice, but it would just ignore the Express and would want me to 'forget' it and would not let me edit it. Airport Utility 5.6.1 was the one that I ended up using the most and finally had success with. It still strikes me as odd that there is no manually way to pick ethernet, it can only be choosen following a 'restore defaults', and only from the 3-option list (the 4-option list had the same ethernet choice, but it no worky).
Thanks for the response. I really do appreciate it.
Aiport Extreme Gen5 - internet access and router
Airport Express Gen2 - connected via ethernet, extending my wireless
- configured while connect directly to the Extreme, but now on a switch (16-port hub)
Using Airport 5.6.1
1) Restore Defaults from Base Station menu
2) Following restart, Select Continue
3) Of the 3 option presented, select 'ethernet.... extend network...'
- if 4 options are present, may not work
4) Wait for the green circle with the big white checkmark.
5) Connected Express to the switch where a cable went to other end of house - works.
Dead-zone went from 2mbps to 24mbps.
I probably spent 4 hours chasing my tail in anger. The correct way took about 5 minutes total.
Thanks again.

How do I extend a network with an AirPort Extreme from an Arris TG862?

I'm using Comcast as my ISP, and after some issues with a previous Motorola modem, they supplied me with an Arris TG862 Router/Modem combo tower. I have two AirPort Extremes, one of which was previously connected to the old Motorola modem to send wireless into the house, but it only reached halfway, so I had the other AirPort Extreme in the middle of the house to "catch" the signal and then broadcast it out to the rest of the house. This worked fine for a while.
But with the new TG862, it doesn't seem to be an option. From what I've read, if I have the TG862 in one room (connected to the cable), AirPort Extreme #1 in the middle of the house, trying to join the existing network (or extend it?), and AirPort Extreme #2 in the far end of the house (to extend from AirPort #1), it won't work. Apple's "extension" technology isn't compatible with all other modems or routers, and even if it was, I'd have to somehow configure the TG862 to "allow to be extended."
So my question is, IF there is a desktop utilizing the TG862 as a direct connection (because it has no built-in Wi-Fi), is it possible to put the TG862 into bridge mode, connect one of the AirPort Extremes and have it act as the router so I can use AirPort Extreme #2 to extend that network out to the rest of the house? I want to ensure the desktop still has a connection, but there's Wi-Fi that actually goes out through the whole house.
The connected-to-the-cable-desktop is a PC; we have multiple iPhones, iPads, and anywhere from 1 Mac laptop to 1 iMac in the house at any given time.

pcbjr wrote:
Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?
Hiya.
You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

Why can I connect to my home network with my iPhone 5 in one room, but when I move to another it is 'unable to connect to the network'

At home, I can connect my iPhone 5 to my home wifi network with no problems, as long as I stay downstairs.
As soon as I go upstairs my phone disconnects from the network. I can still see the home network it in the available network lists (with full signal strength), but when I try to reconnect I get an 'unable to connect to the network message'
If I move back downstairs it reconnects
This has only started happening in the past week or so
I've tried to forget and rejoin the network, but this doesn't work
I reset my network settings on the phone. This worked for a couple of hours and I could connect to the wifi upstairs, but now it won't connect again.
Does anyone have any ideas what is causing this?

Sounds like your wi-fi signal strength has degraded. Try rebooting your wi-fi router, or get it serviced.
Do you have similar issues with any other wi-fi routers?

P1006 - networked with XP and VIsta-64 not printing more than 2 pages

Hello - I have a dilemma with my HP P1006. I have the printer directly plugged in (USB) with my XP (32bit) PC. I have a Vista-64 PC networked with it. Both (XP-32 and Vista-64) are plugged in directly to the router (not wireless). My question is why can I not print more than two pages at a time with items opened on the Vista-64 PC? I CAN print more than two pages with items opened in the XP-32.
Things I've done:
1 - uninstalled everything & reinstalled the latest drivers for the XP-32.
2 - marked the printer as "sharing" on the XP-32.
3 - confirmed the printer is marked "enable bidirectional sharing" under the printer properties on the XP-32 PC.
Things I perplexed about:
1 - why won't items (docs, webpages, etc.) print more than two pages at a time from the Vista-64 PC?
2 - is there any reason that I should download a driver for the Vista-64 OS? If so, which PC do I download it to?
3 - I have another printer (Lexmark inkjet) connected in the same way (except it is a serial port not USB) and it can print more than two pages of a document at one time with no problem from either the XP-32 or Vista-64 PC? Why?
Any thoughts on this situation? Any suggestions are greatly appreciate.
Thank you - Jane.

Hi!
I just get a system message at teh bottom of teh screen saying "output cannot be issued " and it remains on teh same screen . I goto t-code va23 and enter my quotation number and on the top I select sales document ...issue output and select my output type and print preview or prnit , it comes out of that screen into the first screen and at the bottom gives msg "Output cannot be issued". I beleiev its not allowing the smartform to display when there are more than 2 pages , because I tried it with a contact which has 2 pages and it shows output but when I try with the one having more items i.e more than 2 pages it comes out of it . Its a smartform issue and something in the smartform is causing problem I beleive.
Thanks

IPhone6 won't pair with BlueTooth on MBPro

IPhone6, iOS 8.1.1 won't pair with BlueTooth on MBPro nor can I use it as Blue Tooth "hands free" device in my car. Blue Tooth is enabled on the phone and on the MBPro. I try to "connect to network" on the iPhone, using BT preferences on the MBPro, but get the message "can't connect" . On the MBPro, have gone to Sys. Pref., Network, can see the phone but again get the same message when I try to connect.
On the phone under the green button (which enables) the BlueTooth, I see the word "other devices" and a spinning beach ball as the phone tries to find additional devices but no joy.
Have Googled the problem, am reading similar issues - people seem to think it was the new iOS 8.0 and 8.1.1 was supposed to be a fix but it isn't. Any thoughts out there would be much appreciated.

Great - finally got our iPhones6 "discoverable" on our car. Whew!!! Thank you so much.
But, still can't pair our iPHone with my MBPro. Follwed directions on your link but no joy....<sigh>
The MBPro does NOT find the iPhone device. Don't know why......
However, the biggest problem is solved, hopefully.....that being the car/phone connection.
Appreciate the assistance.
thx

Bluetooth for iPhone 6 still won't pair with my car after iOS 8.1 update

So frustrated. I assumed that Apple knew about the problem and that iOS 8.1 would fix what is clearly a very common/widespread issue. Bluetooth is not exactly a new technology... how is it that Apple creates a highly advanced phone, but it can't make a 10-15 years-old technology work?
I never had any issues with my 5S, but my iPhone 6 has not been able to pair with the Bluetooth in my 2011 Mini Cooper since the day I got it (no phone or BT audio). The 8.1 update has had zero effect on the sequence of events that occur when I try to pair my phone. The car has no problem recognizing the phone, and I can see the car listed under Bluetooth devices, and when I select the car from the list of devices on the phone, the screen to enter the pairing code comes up on my car display. The problem is that the phone never gives me the code to enter into the car display.
I have tried all the "tricks" people have used to get their BT to work (deleting all phones from car, resetting all phone settings, renaming the phone, etc). Nothing works for me. I really don't want to have to get rid of my 6, but since Apple has never publicly acknowledged the problem, I have no way of knowing if this is ever going to be fixed.
Really disappointed in you Apple. This is my 3rd iPhone, and you're about to lose a loyal customer if you don't get this sorted out very soon.

The same problem here. iPhone 6 with iOS 8.1.2 and bmw 328i 2013 with latest Bluetooth update doesn't pair. The phone will see the car in bluetooh settings but fails to connect. Based on apple tech support I did the following:
1. powered thr phone down and back on- no help
2. Removed all other phones from iDrive- no help
3. Tried with wi if off - no help
4. Reset network settings- no help
5. Restored my phone entirely to factory settings- no help
The phone can pair to other Bluetooth devices and the car can pair with iphone 4 running iOS 7 no problem. my wife's iphone 6 won't pair with my car either.
I sure hope apple is still working to correct this!

PB won't network with G5 & emac

Similar Messages

Maybe you are looking for