PBR feature in cisco 3548 nexus switch

Hi All ,
Could you please tell me whether cisco 3548 switch will support PBR ? we do have license of Lan1k9 enterprise license switch. But we are not ableto use the PBR featutre. Any help on this..
Regards,
Vijay.

See table-5 in this link:
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/licensing/guide/b_Cisco_NX-OS_Licensing_Guide/b_Cisco_NX-OS_Licensing_Guide_chapter_01.html#fntarg_13
Note 19:
The LAN_BASE_SERVICES_PKG license needs to be installed in order to use the LAN_ENTERPRISE_SERVICES_PKG license.
HTH

Similar Messages

  • Nexus 2K to Cisco 2960 IOS Switch

    Hi,
    I am trying to connect Nexus 2K FEX to Cisco 2960 IOS Switch (Trunk config) and causing spanning tree loop having issues. I am aware that I should't be connecting non host port to 2K FEX but it's corner case. I have done similar setup with Access Port configuration and didn't faced any issues.
    Nexus 5K config Config 
    interface Ethernet107/1/47
      switchport mode trunk
      switchport trunk allowed vlan 500-501
      spanning-tree guard root
      spanning-tree bpdufilter enable 
    interface Ethernet108/1/47
      switchport mode trunk
      switchport trunk allowed vlan 500-501
      spanning-tree guard root
      spanning-tree bpdufilter enable 
    2960-Config 
    interface GigabitEthernet1/0/47
      switchport mode trunk
      switchport trunk allowed vlan 500-501
     spanning-tree bpdufilter enable
    interface GigabitEthernet1/0/48
      switchport mode trunk
      switchport trunk allowed vlan 500-501
     spanning-tree bpdufilter enable
    Error Log
    %FWM-2-STM_LOOP_DETECT: Loops detected in the network for mac 001b.1700.0130 among ports Eth107/1/47
    Eth108/1/47 vlan 500 - Disabling dynamic learn notifications for 180 seconds 
    Should I configure port as "spanning-tree port type network" and create VPC and "storm-control broadcast level" to stop future occurrence?  OR Do i have to configure anything else to prevent spanning-tree loops? 
    Thanks for your help
    Ritesh

    Hi,
    spanning-tree port type network is used for VPC peer-link.  Try creating a new VPC and add ports 107/1/47 and 108/1/47 to it and a Portchannel on the 2960 and test.
    HTH

  • Cisco 3548 Switch Failure

    We have OpenVMS running on a Streams Environment OSI protocol connecting to a Cisco 3548 switch with fiber GBIC trunk ports. The ports display link lights, but network connection to a Windows NT 4.0 Server (Service Pack 6) with Allied Telesyn NICs (half-duplex) fails with LAN Connection Errors reported on DHCP Client Computers. However, when the Switch is bypassed, and directly connected to the Server, problem disappears. Do I have a duplex mismatch problem or IOS release issue?

    You have to check to see how the switchports are configured , by default the speed is auto/auto , if the ports are hardcoded to a specific speed and duplex then you probably have a speed/duplex mismatch. Match both ends of the links , if nics are auto then the switchport should be auto . If the nics are hard set to a speed/duplex then you have to set the switchport the same.

  • PoAP message on Nexus switch

    Hi,
    We are seeing this message continually coming from our new Nexus switch. Is this a problem?
    how do we subdue this.
    2013 Aug 13 04:05:34 switch %$ VDC-1 %$ %POAP-2-POAP_DHCP_DISCOVER_START: POAP DHCP Discover phase started
    2013 Aug 13 04:05:34 switch %$ VDC-1 %$ %POAP-2-POAP_INFO: Abort Power On Auto Provisioning and continue with normal setup ?(yes/no)[n]:
    2013 Aug 13 04:05:34 switch %$ VDC-1 %$ %POAP-2-POAP_FAILURE: POAP DHCP discover phase failed
    2013 Aug 13 04:05:34 switch %$ VDC-1 %$ %POAP-2-POAP_INFO: Abort Power On Auto Provisioning and continue with normal setup ?(yes/no)[n]:
    2013 Aug 13 04:05:39 switch %$ VDC-1 %$ %POAP-2-POAP_DHCP_DISCOVER_START: POAP DHCP Discover phase started
    Thanks for all inputs.

    Hi,
    The message is caused by the Cisco PowerOn Auto Provisioning process. This is a feature that simplifies upgrading software and installing configuration files on new Cisco Nexus switches. This is not a problem assuming the switch has just been installed and has not yet been configured.
    To stop the messages you simply press Y and return at the prompt "%POAP-2-POAP_INFO: Abort Power On Auto Provisioning and continue with normal setup ?(yes/no)[n]:"
    Regards

  • Ask the Expert: Packet Capture Capabilities of Cisco Routers and Switches

    With Rahul Rammanohar 
    Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about packet capture capabilities of Cisco routers and switches.
    In May 2013, we created a video that included packet capture capabilities across multiple Cisco routers and switches. For each product, we began with a discussion about the theory of the capabilities, followed by an explanation of the commands, and we concluded with a demo on real devices. In this Ask the Expert event, you’re encouraged to ask questions about the packet capture capabilities of these Cisco devices:
    •       7600/6500: mini protocol analyzer (MPA), ELAM, and Netdr
    •       ASR9k: network processor capture
    •       7200/ISRs: embedded packet capture
    •       Cisco Nexus 7K, 5K, and 3K: Ethanalyzer
    •       Cisco Nexus 7K: ELAM
    •       CRS: show captured packets
    •       ASR1K: embedded packet capture
    More Information
    Blog URL: Packet Capture Capabilities of Cisco Routers and Switches
    Watch the Video:  https://supportforums.cisco.com/videos/6226
    Hitesh Kumar is a customer support engineer in the High-Touch Technical Services team at Cisco specializing in routing protocols. He has been supporting major service providers and enterprise customers in routing, Multiprotocol Label Switching (MPLS), multicast, and Layer 2 VPN (L2VPN) issues on routing platforms for more than three years. He has more than six years of experience in the IT industry and holds a CCIE certification (number 38757) in service. 
    Rahul Rammanohar is a technical leader with the High-Touch Technical Support Team in India. He handles escalations in the area of routing protocols and large-scale architectures for devices running Cisco IOS, IOS-XR, and IOS-XE Software. He has been supporting major service providers and large enterprise customers for routing, MPLS, multicast, and L2VPN issues on all routing platforms. He has more than 13 years of experience and holds a CCIE certification (number 13015) in routing/switching and service provider.
    Remember to use the rating system to let Hitesh and Rahul know if you have received an adequate response.  
    Because of the volume expected during this event, Hitesh and Rahul might not be able to answer each question. Remember that you can continue the conversation in the Service Provider, sub-community forum shortly after the event. This event lasts through November 1, 2013. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

    Hello Erick
        Thanks for the topology. The trigger will be different for labelled  packet as you would need to mention the values of labels too in the  trigger.
         Below are two examples of one or two labels being  used, it depends on where you are capturing the packet in mplsvpn  scenario which will decide teh number of labels being imposed on the  packet.
    Trigger for one label. (if the router on which you are capturing the packet PHP is being performed)
    VPN label - 5678
    Source Address - 111.111.111.111
    Destination Address - 123.123.123.123
    show platform capture elam trigger dbus others if data = 0 0 0 0x88470162 0xE0000000 0 0 0x00006F6F 0x6F6F 7B7B 0x7B7B0000 [ 0 0 0 0xffffffff 0xf0000000 0 0 0x0000ffff 0xffffffff 0xffff0000 ]
    Trigger for two labels. (for other core routers)
    IGP label - 1234
    VPN label - 5678
    Source Address - 111.111.111.111
    Destination Address - 123.123.123.123
    show platform capture elam trigger dbus others if data = 0 0 0 0x8847004D 0x20000162 0xE0000000 0 0 0x00006F6F 0x6F6F7B7B 0x7B7B0000 [ 0 0 0 0xffffffff 0xf000ffff 0xf0000000 0 0 0x0000ffff 0xffffffff 0xffff0000 ]
        You can check the labels being used (by using show ip cef <> details) and covert their values to hex and change the trigger accordingly.
         I have changed the colors for better understanding. If you notice carefully in the trigger the values for ip address, labels have just been converted to their respective hex values which could be replaced.
         Please let me know if this helps.
    Thanks & Regards
    Hitesh & Rahul

  • Cisco MDS 9418 switch doubt

    Hi Team,
    We have an issue, whether the cisco MDS 9418 switch supports FCIP feature.
    We are planning to migrate the data from our old data center over WAN to the EMC VNX storage box in other location.
    In our old data center we have 2 FC cisco switches connected to the EMC clariion storage array. Inorder to replicate data from clariion box to EMC VNX box over WAN ,it can be done via FCIP.
    I wanted to know if we can use insert the FCIP converters into these MDS 9418 switch or do we need to have separate FCIP converters.
    Do we need FCIP converters on both sides for doing replication over FCIP.
    For clear understanding please see the attachment.
    Will waiting for your response......
    Regards,
    Pranav.

    Hi,
    Since the 9148 does not have IP interfaces, something will be needed to tunnel the FC into IP (FCIP) such as an MDS 9222i, which has both FC interfaces and GigE interfaces and supports FCIP.
    Regards,
    David

  • ACI-How are the new advancements in ACI helping the drawbacks in nexus switching?

    ACI-How are the new advancements in ACI helping the drawbacks in nexus switching?

    ACI is a paradigm shift in data centre designs.
    According to this solution overview ACI is the next generation of Software Defined Networking:
    http://www.cisco.com/c/en/us/products/collateral/switches/nexus-9000-series-switches/guide-c07-731461.html
    Having worked with Nexus switches for a couple of years now I haven't encountered any serious drawbacks with these devices.

  • Cisco catalyst 2690 switch vlanTable

    Hi,
    I have a cisco catalyst 2690 switch.
    I want monitoring IP, MAC, and Port Address.
    I use this docu: http://docstore.mik.ua/orelly/perl/sysadmin/ch10_03.htm
    This works great:
    htvtef7-nagios:/ # snmptranslate -On BRIDGE-MIB:dot1dTpFdbTable
    .1.3.6.1.2.1.17.4.3
    snmpwalk -c tef7snmp@761 -v 2c 10.76.1.7 .1.3.6.1.2.1.17.4.3
    htvtef7-nagios:/ # snmptranslate -On BRIDGE-MIB:dot1dBasePortTable
    .1.3.6.1.2.1.17.1.4
    snmpwalk -c tef7snmp@761 -v 2c 10.76.1.7 .1.3.6.1.2.1.17.1.4
    htvtef7-nagios:/ # snmptranslate -On CISCO-STACK-MIB:vlanTable
    .1.3.6.1.4.1.9.5.1.9.2
    But I get a error:
    htvtef7-nagios:/ # snmpwalk -c tef7snmp -v 2c 10.76.1.7 .1.3.6.1.4.1.9.5.1.9.2
    SNMPv2-SMI::enterprises.9.5.1.9.2 = No Such Object available on this agent at this OID
    Switch config:
    snmp-server community testament RO
    snmp-server community tef7snmp RO
    snmp-server location XYZ
    snmp-server contact MR.XYZ
    snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
    snmp-server enable traps tty
    snmp-server enable traps cluster
    snmp-server enable traps entity
    snmp-server enable traps cpu threshold
    snmp-server enable traps vtp
    snmp-server enable traps vlancreate
    snmp-server enable traps vlandelete
    snmp-server enable traps flash insertion removal
    snmp-server enable traps port-security
    snmp-server enable traps envmon
    snmp-server enable traps mac-notification
    snmp-server enable traps copy-config
    snmp-server enable traps config
    snmp-server enable traps bridge newroot topologychange
    snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
    snmp-server enable traps syslog
    snmp-server enable traps vlan-membership
    snmp-server host XXX.XXX.XXX.XXX public
    snmp-server host YYY.YYY.YYY.YYY  tef7snmp
    What did I do wrong?
    THX!

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Normál táblázat";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    Thx for the replay!
    I use on the switch c2960-lanbasek9-mz.122-25.SEE3.bin (IOS),
    the Cisco Feature Navigator say, this IOS support the CISCO-STACK-MIB:
    http://tools.cisco.com/ITDIT/MIBS/MainServlet?ReleaseSel=0&PlatformSel=0&fsSel=0&IMAGE_NAME=c2960-lanbasek9-mz.122-25.SEE3.bin&SUBMIT2=Submit&IMAGE_ID=816103
    In show snmp mib I could not find the vlanTable. See the attachment.
    I du not understand!

  • Nexus switch for storage

    we are currently evaluating solutions for our storage upgrade.
    we required 10GbE connection from storage to our servers.
    there are 2 proposals that uses nexus switch.
    1 uses nexus 5548 while the other one uses 3524.
    i understand that 5548 is of a higher grade than the 3524.
    i have 7 dell servers that will be connected to the switch using 10GbE NIC.
    which nexus switch is more suitable for my environment.
    7 servers -> 2 10GbE iSCSI switch -> 1x iSCSI storage(20TB)

    Well...you're on a Cisco forum, so we'd be remiss in not recommending Cisco gear. 
    The Nexus 5548UP is around 17k for the base model without any special layer 3 licenses. 
    http://www.softchoice.com/catalog/en-us/hubs-switches-cisco-nexus-5548up-switch-managed-N5K-C5548UP-FA-HV7684
    If you don't use layer 3 on the Nexus (which I wouldn't), they've got pretty good port density for the cost.  NXOS takes little bit of getting used to and, for us, the copper SFPs have been a royal pain in the ass, but otherwise, they're pretty solid devices. 

  • Cisco Catalyst Blade Switch 3020

    Information about the Cisco Catalyst Blade Switch 3020
    Does it support  TCP SYN Flooding Attacks Mitigations Techniques
    As per the Request for Comments: 4987 

    Most of the common DOS attack mitigation strategies (good overview here) are configurable on the CBS 3020. There's no "one step lockdown" like the autosecure feature on routers but the configuration guide covers all of the details on setting the individual mechanisms (DHCP Snooping, DAI, IP source guard, etc.) you may wish to employ.

  • Cisco 4506 network switch

    i need details of cisco 4506 network switch with supervisor module

    Hi,
    You can visit
    http://cisco.com/en/US/products/hw/switches/ps4324/prod_brochure_list.html
    a Good link on 4500 supervisor engines.
    Regards
    Dinesh
    http://Knowurtech.com
    (Good technical articles. Submit your articles and get featured on our website. Send email to [email protected] To know the benefits http://www.knowurtech.com/be_an_expert.html)
    Hi,
    You can visit
    http://cisco.com/en/US/products/hw/switches/ps4324/prod_brochure_list.html
    a Good link on 4500 supervisor engines.
    Regards
    Dinesh
    http://Knowurtech.com
    (Good technical articles. Submit your articles and get featured on our website. Send email to [email protected] To know the benefits http://www.knowurtech.com/be_an_expert.html)

  • Adapter-fex Supported VICs and Nexus Switches

    HI,
    I am thinking of using C220M4 in standalone mode. I have been reading about adapter-fex and I am wondering which Cisco VIC supports adapter-fex and which Nexus Switch will support adapter-fex.
    I am thinking of using a VIC1225 and Nexus 3000.
    Thanks.

    I believe that adaptor fex is supported only with Nexus 5k and N2k:
    Network Adapter Virtualization Design (Adapter-FEX) with Cisco Nexus 5500 Switches and Cisco Nexus 2232 Fabric Extenders
    http://www.cisco.com/c/en/us/products/collateral/switches/nexus-5000-series-switches/guide_c07-690080.html
    http://www.cisco.com/c/en/us/products/collateral/switches/nexus-5000-series-switches/data_sheet_c78-657397.html

  • Steps to upgrade Cisco MDS core switch

    Hello,
    We wanted to upgrade our Cisco SAN core switch firmware. Currently we are running below firmware version. We wanted to go to latest version NX OS 5.2 (x) but as per the white paper i need to go to 5.0 (X) and after that i need to upgrade it to 5.2 (x). Can some help me with the steps to follow the upgrade. I have th cook book but just need the main steps to perform the upgrade.
    kickstart: version 4.1(1c)
      system:    version 4.1(1c)

    are you using IVR non-NAT, if you are you need to convert to IVR-NAT before you go to 5.2. Other than that you just follow the  normal procedure, look at the release notes for each firmware to make sure your hardware is supported and then do the usual
    install all system bootflash:m9x00-xxx.bin kickstart bootflash:m9x00-xxx-kickstart-xx.bin
    as a side note, i know you don't mark people replies to your questions as helpful/correct on EMC ECN ..at least do it here to show your appreciation.
    @dynamoxxx

  • Power Redundancy problem for cisco 3750 stack switches

    Hi Team,
    I have installed and configured cisco 3750X series switches in stackwise. Those are having dual power supply.
    Power redundancy test performed:
    1. Removed one of the power supply and inserted it back.
    2. once the first power supply is ready, removed another power supply and switch got rebooted.
    please find the below stack-power output:
    JP2-RDC-DIS-02#sh stack-power detail
    Power Stack           Stack   Stack    Total   Rsvd    Alloc   Unused  Num  Num
    Name                  Mode    Topolgy  Pwr(W)  Pwr(W)  Pwr(W)  Pwr(W)  SW   PS
    Powerstack-2          SP-PS   Stndaln  700     477     223     0       1    2
    Powerstack-1          SP-PS   Stndaln  700     477     223     0       1    2
    Power stack name: Powerstack-2
        Stack mode: Power sharing
        Stack topology: Standalone
        Switch 2:
            Power budget: 223
            Power allocated: 223
            Low port priority value: 22
            High port priority value: 13
            Switch priority value: 4
            Port 1 status: Not connected
            Port 2 status: Not connected
            Neighbor on port 1: 0000.0000.0000
            Neighbor on port 2: 0000.0000.0000
    Power stack name: Powerstack-1
        Stack mode: Power sharing
        Stack topology: Standalone
        Switch 1:
            Power budget: 223
            Power allocated: 223
            Low port priority value: 22
            High port priority value: 13
            Switch priority value: 4
            Port 1 status: Not connected
            Port 2 status: Not connected
            Neighbor on port 1: 0000.0000.0000
            Neighbor on port 2: 0000.0000.0000
    Can anyone help what went wrong here?
    Thanks
    Manish

    Cosmetic bug
    CSCui21029    3750X Stack no standalone stays in running configureation as standalone
    Symptom:
    When you are configuring a 3750x stack and initially putting it into a stack ring topology by configuring the following.
    Switch(config)#stack-power switch 1
    Switch(config-switch-stackpower)#sta
    Switch(config-switch-stackpower)#no stan
    Switch(config-switch-stackpower)#no standalone
    You will see that in the running configuration it shows up as standalone mode
    stack-power switch 1
    switch mode: standalone
    stack-power switch 2
    switch mode: standalone
    Conditions:
    3750X stacks with any license level
    Workaround:
    none

  • Connection of LC/APC fiber patch cords to Cisco Catalyst 6500 $ Cisco Access 3750 Switches

    I have an LC/APC fiber patch cord infrastructure and I want to connect it to Cisco Catalyst 6500 & Cisco Access 3750 Switches. what type of transceiver should be used?
    I read a note on Cisco website stating the following for Cisco SFP+ transceivers:
    Note: "Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section"

    Thank you,  but my question is that I have a single mode fiber patch cord with LC/APC connector while cisco stating a note that only use LC/PC or LC/UPC type of connectors with SFP+ transceiver.  
    So what type of transceiver should I use to connect LC/APC patch cord to cisco switches?  Is there another type or SFP+ still can be used? 

Maybe you are looking for

  • Ultimate 3B Monitoring Prorated Upgrade Questions!?

    I recently enrolled in the 3 Credit Bureau Monitoring for $24.99/Month on June 24 (almost 3 weeks ago). I got a message at the bottom of my Dashboard saying I could upgrade to the 3B Ultimate at a prorated price, since it hasn't been a month. It says

  • How do you add a device to sync with my iBooks?

    I have an iPad and iMac synced with each other for my iBooks.  I can't get the same books on my MacBook Air.  The settings of all are set to sync.

  • FI Data download

    Dear Experts I want to download last one year data for the following : 1. Cash Entries 2. GL entries 3. Credit Note / Debit notes 4. Asset Entries This is required to analyse the volume of data.. Please help me how to get the data... I have tried wit

  • Problems pasting or opening image in Illustrator

    Hi, I'm simply trying to paste an image onto Illustrator that's 150 px x 150 px, but for some reason Illustrator re-seizes it so it's 90 px x 90 px and it's really distorted. It's the same when I just open the image in Illustrator too. Anyone know wh

  • PC SERAIL INTERFACE FOR IV CURVE TRECER APPLICATION WITH MICROCONTROLLER

    DEAR        I AM TRYING TO BUILD   IV CURVE TARACING APPLICATION USING MICROCONTROLLER CONNECTED WITH PC SERAIL PORT I HAVE STUDIED BASIC PC SERAIL PORT INTERFACING BUT HAVE NO IDEA ABOUT HOW TO DISPLAY AND LOG THESE DATA ON GRAPH AND SAVE ON  A FILE