(PBR) set next-hop to the same router?

Hi
I need to send some traffic to an external L2 device, and then get it back, to the same router.
I planned to use PRB, to set the outgoing interface, and the next-hop as the IP address of the incoming interface, from the same router.
Is that possible?
Can I set as the next-hop an IP address from the same router, forcing the traffic to go out, by specifying the outgoing interface too?
Thanks in advance
JM

JM,
Good catch, I did try the command on a router today, and it did show up in the running config. Its indeed a warning message, but I m not sure whether the router will route packet to itself..if I get some time today i will test it out.
Sankar.

Similar Messages

  • Network address as the next hop address in ip route statement???

    Hi All,
    I am confused about ip route statements in the following Cisco document.
    Configuring ISDN DDR with Dialer Profiles
    Document ID: 9568
    http://www.cisco.com/warp/public/793/access_dial/ddr_dialer_profile.html
    The statements are;
    ip route 172.22.0.0 255.255.0.0 172.22.80.0
    ip route 172.22.80.0 255.255.255.0 Dialer1
    Why does it use network address as next hop address on the first line?
    And it is a source network address on the second line.
    Please suggest me.
    Thanks a lot,
    Nitass

    When you specify a network address as next hop in a ip route statement, the router does recursive lookup. When it matches a packet for a network other than 172.22.80.0, it will match the router 172.22.0.0 and the route basically says use 172.22.80.0 as the next hop. Now the router looks up the routing table for how to reach 172.22.80.0 and ends up routing via Dialer 1.

  • Home Sharing not working between wireless PC's / devices and ethernet wired PC's on the same router.

    Home Sharing is not working between wireless PC's / devices and ethernet wired PC's on the same router.  I installed a new Verizon FIOS ActionTec  MI424WR GigE wireless / ethernet router, replacing the original FIOS router.  With the old router Home Sharing worked fine across and among all iOS and Windows wired and wireless devices.  With the new router Home Sharing works between and among the Wired PC's but not between the wired PC's and the Wireless connected PC's or iOS devices.  Home Sharing also works between and among the wireless connected PC's and iOS decices but not between them and the wired PC's.
    Only the router was changed.  No changes were made to any of the devices except all were updated with the latest version of iTunes 10.7.0.21 and the iSO devices were updated to iOS vrsion 6.01.  Three PC's are wired and all are running Windows 7.  There also is a Windows Home Server connected to the router by ethernet port.  It does not run iTunes but does provide WebDAV services to my iOS devices.  This works fine.  Two PC's are wireless, one running Windows 7 and one running Windows 8.  All of the PC's are connected to the same (new) router via it's ethernet ports and it's wireless access point.  Two of the wired PC's are connected via a high-speed  ethernet hup that is connected to the router (Home Sharing works fine between the two PC's on the hub and the PC on the router).  All wired and wireless devices on the router are visible and members of the router's Home/Office virtual network.
    All of the PC's are visible in the Windows network and all shared files are accessable from all PC's, both wired and wireless.
    Obviously the router seems to be the issue, something between the ethernet and the wireless access point components.  I checked the settings and found nothing that would prevent Home Sharing between the wired and wireless devices.  There is no setting that isolates the wireless network.  I have done the following:
    Read the router user manual and checked all the settings
    Rebooted the router and tested.
    Turned off the router's firewall and tested.
    Home Sharing is turned on all the devices and all use the same Apple ID.
    Restarted iTunes and tested.
    Verified iTunes is "Allowed" in each PC's firewall.
    Again, I can Home Share between the two wireless PC's but not between either of the wireless PC's and any of the wired PC's.  I can Home Share between my iPads and iPhones and either of the two wireless PC's but not with any of the wired PC's.  I can Home Share between any of the wired PC's but not between any wired PC and a wireless PC or iOS device.
    I hope someone may have had a similar problem and has a fix suggestion.  I'm stumped!  I have a;so contacked ActionTec and awaiting an answer.

    Solution from ActionTec is:
    Log into your router.
    Click the Advanced icon
    Cclick Yes
    Click on the IGMP Proxy
    Select Disable
    Click Apply

  • I have an Apple ID with a single  e mail address. I want to set multiple addresses in the same ID. Can I? If so how?

    I have an Apple ID with a single  e mail address. I want to set multiple addresses in the same ID. Can I? If so how?

    Howdy there johnzcarp,
    As I understand it you want to have more than 1 email address under your Apple ID. You can have what are called Alternate Email addresses associated with your Apple ID and this article will help you get those setup:
    Manage your Apple ID primary, rescue, alternate, and notification email addresses
    Alternate email address
    You can add one or more alternate email addresses for use with Apple services such as Game Center, FaceTime, Find My Friends, iMessage, and OS X notifications.
    Go to My Apple ID (appleid.apple.com).
    Select “Manage your Apple ID” and sign in.
    Add an alternate address:
    Select Add Email Address, then enter your alternate address. Apple will send a verification email to that address. Didn't receive the email?
    Follow the instructions in the email to verify the address.
    Edit an alternate address:
    Select Edit next to the address, then enter the new address. Apple will send a verification email to that address. Didn't receive the email?
    Follow the instructions in the email to verify the address.
    Delete an alternate address: Select Delete next to the address.
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • Can an infected XP system infect a Win7 computer on the same router.

    Hi there....
    I was just wondering if an XP system, once infected, can infect a Win7 on the same router. I know support for XP is dead, but I can't afford to upgrade the OS on the old XP system at this time. I have all available XP updates and Win7 (just did a full format,
    and reinstall of XP).
    I have no network set up, they are just on the same router, both on a cable, not Wi-Fi.
    EDIT: Sorry for posting in the wrong forum....Please move, need be.

    I am currently using AVG anti-virus on both machines. 
    Would that replace it? Or should I use both on my Win7 system?
    I am a gamer, how does it affect gaming? If, at all. AVG has a gaming mode that limits its interference with games.
    Thanks for your help!

  • Using Crypto Maps and IPsec Static VTI's on the same router

    Is it possible to configure both crypto maps and IPsec static VTI's on the same router? What platforms have this capability? What IOS version do I need?

    Yes you can and as far as I know I dont think there is a hardware dependency.
    VTI mode 'tunnel mode ipsec ipv4' was added in 12.3(14)T.
    If you are mixing tunnel protection and crypto map ensure you use iskmp profiles to differentiate somehow that the tunnel IPSec connection is not prcessed on the crypto map!
    Here is a rough example (fine tune it as needed):
    crypto keyring key1
      pre-shared-key address 1.1.1.1 key test123
    crypto keyring key2
      pre-shared-key address 7.7.7.7 key test777
    crypto isakmp profile vpn1
       keyring key1
       match identity address 1.1.1.1 255.255.255.255
    crypto isakmp profile vpn2
       keyring key2
       match identity address 7.7.7.7 255.255.255.255
    crypto ipsec transform-set test esp-des esp-sha-hmac
    crypto IPsec profile vpn-tunnel
    set transform-set test
    set isakmp-profile vpn1
    crypto map mymap 1 ipsec-isakmp
    set transform-set test
    set peer 7.7.7.7
    set isakmp-profile vpn2
    match address 177
    interface Tunnel0
    ip address 10.0.51.217 255.255.255.0
    tunnel source 2.2.2.2
    tunnel destination 1.1.1.1
    tunnel mode ipsec ipv4
    tunnel protection ipsec profile vpn-tunnel
    interface Ethernet4
    ip add 2.2.2.2 255.255.255.0
    crypto map mymap
    Regards,
    Uwe

  • Using "Next style" with the same paragraph style for more than one paragraph

    Hi.
    I have been using paragraph styles with the "next style" option, it's a huge help. But I need a bit more. So I have the following paragraph structure: ABCCCABCCCAB...
    I defined paragraph styles for each kind of paragraph, then in paragraph style A, I added paragraph style B as the next style, and so on. However, when I get to paragraph style C I reach a dilemma. Should I define the next style as the same, or define three paragraph C styles (C1, C2 and C3), link them to each other with next style, and then loop the C3 style into the A style again?
    My hope is that there is a way, something like the nested style options, that allows me to define that style C should be used for 3 paragraphs and then the next style becomes style A again.
    Thanks.

    You just need two styles, almost identical, you can duplicate one.  The only
    difference is one has the next paragraph c and one has the next paragraph
    a.  After that I don't see the problem.

  • I have an IPA2 wifi 3g working fine with wifi up for 3 monthes then from two weeks it get connection but after 1 minutes stop to serf/download with signal and connection always present. With the same router are still connected others 3 pc working!

    I all, 
    the scenario is the following:
    WIFI connection with TISCALI operator. Encryption made by WPA2 EAS with router SITECOM or tested also with another router DIGICOM with WPA TPK.
    From December up to end of March the IPAD2 working perfectly serfing and downloading.
    By two weeks it has a very strange behavour without have changed any configuration on IPAD or network: 
    with WIFI turned on it discover about 4 different ntw among them the mine, I successfully authenticate with psw the my ntw,
    the IPAD2 start to run with Safari without problems, but after about 1 minutes, it stop to serf or download and answer that the Server cannot be reached or the page cannot be open, at the same time the signal is present on the icon of WIFI and it is strong.
    This problem is systematic: If I dissasociate the ntw and then authenticate again I start to serf again for 1 minutes (more or less) and then it stops again, this occurs every time I authenticate the ntw after a disassociation.
    I made some test changing the encryption from WPA2, WPA and also without encryption but the result was always the same, after about one minute the server seems to be for the IPAD2 no more reachable while the others PC and netbook connected to the same router continue to serf/download without problems!
    I also tried to change the router with a DIGCOM that I did not use generally, but the behavour is always the same.
    Since the IOS was the 4.3 revisin, I made the upgrade by means Itunes to IOS 5.1 succesfully installed.
    But unfortunatelly all test repeted have had the same negative result with the same behavour!
    Yesterday I tried to do the complete restore of the System but the tests had the same rsult. 
    I really don't know how to proceed, the problem started suddenly without any action from my side....is there someone that can help me?
    Thanks Massimo

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
     Cheers, Tom

  • I can't send emails from Mail. I have three different accounts set up and have the same problem with all. The mail just sits in my outbox. All worked fine until Yosemite upgrade. Recent update has not fixed problem.

    I can't send emails from Mail. I have three different accounts set up and have the same problem with all. The mail just sits in my outbox. All worked fine until Yosemite upgrade. Recent update has not fixed problem.

    I have been experiencing the same problem. My mail app won't even open on my Late 2011 Macbook Pro. It will show as open, but the app will never actually show up.

  • We just got 2 iPad air today and Set up both with the same Apple ID, now I'm getting messages and FaceTime for my 13 yr old daughter.  Do I have to create a different Apple ID for her?

    We just got 2 iPad air today and Set up both with the same Apple ID, now I'm getting FaceTime and messages for my 12 yr. old.  Do I have to set up a separate Apple ID  for her to avoid this?

    It's a trust issue. You can set them up so you don't receive each other's messages as long as you each have your own email address.
    The trust issue is the fact that either of you can change the separation at any time via Settings by checking the appropriate (inappropriate?) email address.
    To be absolutely sure you can never receive each other's messages will require two Apple IDs.

  • Can I import 2 sets of photos with the same file name numbers?

    I've inadvertantly not had my camera set to "continuous" for file names and now have 2 memory cards with 2 different sets of images with the same file names.
    Can I still import both into Lightroom 2 without problems?
    What are the consequences?
    Thanks
    Stuart

    Yes. Of course, two files with the same name cannot be in the same folder. And don't forget to uncheck Don't import suspected duplicates during import.
    Another thing is that's not a good idea for good asset management, because someday you'll make some mistake because of this ambiguity. Good DAM practices suggest renaming your files after or during import, so that each files has a unique name across your entire image archive.

  • Using ipad2 and airplay with appleTV; can I have the ipad2 on wifi and the AppleTV on a wired port of the same router in order to use airplay?

    can I have the ipad2 on wifi and the AppleTV on a wired port of the same router in order to use airplay?

    I belive you can, I think my friends Apple TV is connected to their internet via an Ethernet cable, and we use Airplay sometimes using our iPads that are connected to the same network via WiFi. It should work as long as they are both connected to the same network. However, I don't have an Apple TV of my own, so don't take this as a solid answer.

  • Every time i play a song in my i-tune 10.6, about up to half way mark, i-tune will automatically skip to the next track and playing it (next track) at the same time as the current track.

    Every time i play a song in my i-tune 10.6, about up to half way mark, i-tune will automatically skip to the next track and playing it (next track) at the same time as the current track. i don't know if anyone has the same problem, but i haven't sync my ipod touch 4 gen to my i-tune playlist for the longest time, cus i was afraid to transfer the problem to it since i have a pc (win 7) but not MAC.

    i am sorry, guys, but  I really really really need you guys' help. if u know ANYTHING...

  • I have my songs set to shuffle, but the same song just keeps repeating.

    I have my songs set to shuffle, but the same song just keeps repeating itself and I have to manually advance.

    Are you simply shuffling a list containing one song?  When the song plays and you see the album art, do you see "1 of 1" on top?

  • Blackberry 9320 broken,9360 on the same route due to "battery to low for radio use" etc

    My previous blackberry 9320 ,which I can't use anymore, aswell as my 9360 that's on the same route as the previous one started out in the beginning with
    -battery to low for radio use(which I would turn back on)
    Later my memory card couldn't be recognized, after some attempts of "fixing the broken files" as the phone would say, and then "repairing failed"
    Problems got worse ,as if I allready can't use a memory card because all 3 got broken somehow,but after that it started saying "battery to low for radio use" then my battery would in a matter of seconds drain and then a message I get atleast 30 times a day "battery drained,shuttingdown handheld". It gets worse, then it says the same message ,but only this time the battery is full, because the phone must be pluged in too a charger to be able to start, and as I call it, then has to be on "life-support"(charging like 24/7). These problems seem to be activated by high radio use or just plainly to irretate a person. I'm very dissatisfied with blackberry and I seek answers. now here comes the catch, I took my previouse blackberry,the 9320, in 2 times to get the software updated and the last time they couldn't say why this is happening , aswell as try putting another(new) blackberry 9320 battery in the phone. It worked for 3 days,no kidding, and the same problems in their stages began.I fear my blackberry 9360 is on the same route and I'm dissatisfied with these products for its expensive and causing trouble. Please help me resolve this problem ???p.s both phones were newly bought since they are contract phones.

    Hi and Welcome to the Community!
    Given that you've already begun formal service for this issue, I recommend you continue with that. After all, they said it was fixed, but it's not...don't you want to challenge them on that fact?
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

Maybe you are looking for