Pc to mac with ethernet
Hello,
Can someone please help me to how transfer file from PC to Mac using Ethernet cable?
I followed the instruction on the mac web and the support but still unsuccessful. Help?
Thank you
Provide a link to the instruction.
Similar Messages
-
Connect PC directly to my Mac with Ethernet?
This may be the wrong place to post this, but can I network a PC to my Mac directly with a single Ethernet cable?
Currently they're networked via a hardwired router, but I want to set up my Mac desktop for a wireless connection to an airport base station, but I still need my PC to talk to my Mac. I would actually prefer not to have my PC connected to the internet at all (so I don't want to set the PC up for wireless access), just to my Mac...Hi Nolan!
You have a G4 dual and if I recall correctly it is gigabit capable. That means it can also use either a cross-over or a standard straight-through Ethernet cable to connect directly to your Windows computer. Otherwise you'd have to use a cross-over cable.
Connect the two with a cable and make sure file sharing is enabled on both. Each will assign itself an IP address in the range of 169.254.xxx.xxx and therefore be able to communicate with the other machine.
To make things a little easier, put them both in the same WORKGROUP. On Windows, right-click "My Computer" and select Properties. You can set a WORKGROUP name under the computer name tab. On Mac OS X, open the Directory Access application found in /Applications/Utilities. Configure SMB and put the same WORKGROUP name in there as well.
When you browse the network from either machine, you should be able to see the other.
Hope this helps! bill
1 GHz Powerbook G4 Mac OS X (10.4.8) -
Can 2 Macs connect with ethernet cable to share DVD for remote install?
Can I simply connect a Mac Mini Server and MacBook together with an ethernet cable?
I want to reinstall Mac OS X Server on the DVDless Mac Mini. There is no separate AirPort device.
So do I just connect the two machines with an ethernet cable, start the remote install program on the MacBook, then restart the Mac Mini with the Option key pressed?
Thanks.According to page 57 of the Getting Started 10.6 server manual, you can use a Mac with a DVD drive operating in target disk mode for this. I see no mention of using Ethernet so I assume it is not supported. Even if it was, it would be extremely slow compared to using FireWire target disk mode.
-
Windows migration assistant won't go passed the first screen. Connecting hp files to new Mac mini with Ethernet cable. Also tried USB
Are you following these instructions?
http://support.apple.com/kb/ht4796
Have yo tired by connecting both to same network vice direct ethernet connection?
There is no direct USB connection -
Mac OS X will not connect to wifi, airport is broken, will connect to internet with ethernet cord. Is there an accessory I can buy to replace airport so I don't have to use ethernet cord? Please help!!
Since the MacBook Pro currently works, you should put it next to the iMac and compare the network settings for AirPort in System Preferences Network pane Advanced. Also, if you want to start off with the default network settings, you can use Location drop down menu and select +Edit Locations+. Then click the plus sign to create a new location. Set up that new location.
On System Preferences Network pane, AirPort should appear at the top of the list (in the sidebar). To change the service order, click on the gear icon and select +Set Service Order+.
Some additional tests you can try, on top of seeing if it works with (1) WEP security disabled and (2) a direct wired connection to the router.
If you get it to work with either (1) or (2), be sure to run Software Update at least two times to apply any recent updates from Apple. See if that makes any difference to using AirPort with WEP back on.
(3) Start up in Safe Mode
http://support.apple.com/kb/HT1455
I don't know if any third-party software has been installed on the iMac at this point, but Safe Mode will start up with only the essential Apple extensions and processes running. See if it works any better in Safe Mode.
(4) Create a new admin user account in System Preferences Accounts pane
http://docs.info.apple.com/article.html?path=Mac/10.6/en/8235.html
Log out and log in to the new account. Try connecting with AirPort in the new account.
(5) Connect the MacBook Pro to the router with a wired Ethernet connection. Make sure its Internet access works. On System Preferences Sharing pane, set it up for +Internet Sharing+ so that it is set to +Share your connection from Ethernet - To computers using AirPort+. On the iMac, try to connect to that wireless network and access the Internet.
That last one (5) may be a good one to try first. It would at least show that the iMac's AirPort is working - you can even set it up to use WEP. If you have any questions about using the +Internal Sharing+ feature, please ask. -
I have Power Mac G5 1.8 single. I have a problem with ethernet port, before it was working with the internet, but now i shows it is connected even the cable is disconnected. I'm running Leopard 10.5. any help
Reset the PRAM.
http://support.apple.com/kb/HT1379
If that fails, reset the PMU.
Scroll down the following page and click the G5 link for instructions:
http://support.apple.com/kb/ht1939 -
Hi there
Does anyone know how I can migrate ALL of the partitioned drives from my old macbook 17 inch to new macbook 2013?
Seems like it only transfers the Macintosh HD drive - ie the user account - and I can't figure out how to transfer the rest of the partitioned drives?
I am using an ethernet cable with thunderbolt adapter. (I don't have a thunderbolt firewire adapter to use a firewire cable in disc target mode - hoping I can perform the FULL transfer using just the ethernet cable?
but no additional options for transferring additional drives show up when I use Migrate assistant?
Thanks
TYou can't use Migration Assistant to transfer files to OS X Mountain Lion from Mac OS X Tiger. See > http://support.apple.com/kb/HT4889?viewlocale=en_US&locale=en_US
What you have to do is to connect both Macs with FireWire, put the old one in Target Disk mode (hold the T key while the Mac mini is starting) and use Finder to restore the data you need manually. Another option is to transfer your files over the network > http://support.apple.com/kb/HT1549 -
My problem is that I don't know how to use my Time Capsule with Ethernet Cable, as when I use wireless it is really slow.
Make sure that there is an Ethernet cable from one of the LAN <-> ports on your modem/wireless router to the WAN port on the Time Capsule
Click on the Wireless tab at the top of the page
Change the setting for Wireless Mode to Off (I assume that you do not want the Time Capsule to provide a wireless network since you already have a wireless network)
Next, click the Internet icon at the top of the screen, then click the Internet Connection tab
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Click the Update button at the bottom and wait 30 seconds for the Time Capsule to restart and display a green light
Then, you must power off your entire network...all devices....in any order that you want
Wait a minute
Start your modem/router first and let it run a minute
Start the Time Capsule and let it run a minute
Keep starting devices one at a time until everything is powered up
If you are using Time Machine for backups, you will need to reset the connection because you have changed the way in which the Time Capsule connects to your network
Open System Preferences (gear icon) on the dock
Open Time Machine
Click Select Disk
Click the Time Capsule to highlight it
Click Use for Backup or, it might be Use Disk
Now you can connect your Mac using an Ethernet cable to one of the LAN <-> ports on the Time Capsule to back up using Ethernet. Be sure to turn off the wireless on your Mac before you start the backup.
If you want to backup using wireless, disconnect the Ethernet cable from the Mac to the Time Capsule and turn on the wireless and connect to your wireless network. Your computer will now backup using wireless. -
How do I set up airport on my macbook pro (wired with ethernet to a cable modem) and the wifi settings on my ipad2 to enable the use of wifi on my ipad?
http://docs.info.apple.com/article.html?path=Mac/10.5/en/8156.html
-
Can I use migration assistant from a mac with leopard to a mac with tiger?
My old mac was upgraded to leopard, (don't ask me why), and I just got a new mac with tiger, although I ordered leopard up to date. Can I use migration assistant to move stuff from the old mac with leopard to the new mac with tiger, or do I have to wait until I get the copy of leopard? Plus, if I move files over now- like through email and/or network connection, and then when I get leopard and archive and install, what happens to my files?
That is correct. You'll need either an ethernet cable or a firwire cable and a firewire to thunderbolt adapter to connect the two macs together. Here's info on Migration/Setup assistant
http://support.apple.com/kb/HT4889?viewlocale=en_US&locale=en_US -
How can I create a new TC backup with ethernet, so I don't have to wait two days for a new wireless backup?
Several times in the last year, I've gotten a message that Time Machine needs to completely redo my backup. Using the wireless connection, this takes almost two days. Is there a way to do the backup with ethernet and then switch back to wireless? Thanks.May I know what is needed to make sure the MacBook is able to see Time Capsule on ethernet?
Connect an Ethernet cable from one of the LAN <-> ports on the 2Wire gateway to the WAN port (circle of dots icon) on the Time Capsule.
If AirPort Utility cannot "see" the Time Capsule now, you will need to perform a "hard reset" by holding in the reset button for 7-8 seconds or so and then reconfigure the Time Capsule. You can use the same Time Capsule name and password, etc. as before.
Configure the Time Capsule to "Create a wireless network" and select the Bridge Mode option when it appears during the setup using AirPort Utility.
Once the Time Capsule is configured, restart the entire network again. Power down everything, start the 2Wire first and then start each other device after that one at a time about a minute apart.
Now you can connect your Mac directly to one of the LAN <-> ports on the Time Capsule for the backup using another Ethernet cable. In general, about 20-25 GB per hour will transfer.
The Time Capsule will broadcast a much faster wireless network than the 2Wire can provide, so you might want to leave the setup "as is" for awhile after the first backup is complete. If you decide to use the Time Capsule as your main wireless access point, you would want to turn the wireless off on the 2Wire since two wireless networks in close proximity can create interference problems.
Or, if you want to use the wireless on the 2Wire, you could turn off the wireless on the Time Capsule. Then backups will occur over the 2Wire wireless, or over Ethernet.
I don't really recommend the "Join a wireless network" setting on the Time Capsule for most users, but you could go back to that setup as well if you want after the first backup is complete. -
How do I get my old printer "HP Laserjet 4mv" to work on my newer Macs with OSX?
How do I get my old printer "HP Laserjet 4mv" to work on my newer Macs with OSX?
There is no HP support for this old printer. I have tried to connect via ethernet (thru ethernet router), and it does not show up in printer preferences. The printer worked fine on system 9x but when I went to my new macs with system X no luck. This is a great B&W printer that prints at 18 x 24". I would like to keep it and not junk it, but its been sitting on my desk unused for some time now. Any thoughts or JUNK IT! Thanks, R.T.Does anyone at Apple have help for this sort of question - I too have an old printer (HP LaserJet 5MP) that I would like to keep using on my Mac. (Mac OSX 10.6.8).
I got it working by getting a USB cord that connects to it - but every once in a while it just stops working for weeks. The mac 'sees' it and it sends the data because the printer lights start blinking but then it just doesn't do anything. Is there no one who can tell me (and raterada) how to get some new life into these old printers. I would rather not add this (and a new toner cart) to the landfill just yet. . . -
Why won't my Mac, with Mountain Lion installed boot up?
I had problems getting my Mac to boot so I made a Genius Bar appointment at my local Apple Store. The ran some tests and discovered a "disk i/o" error which they said indicated that my hard drive needed replacing. Hard drive replaced, brought it home, restarted, set up, Disk Utility run (permission checks out, disk checks out), Time Machine back up loaded and still all I get is the grey screen with the apple logo and the spinning wheel (not beach ball). Why won't it boot up? Any ideas???
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. -
Best practice for moving from a G5 to a new Mac with SL
I am receiving my new iMac today (27") and am very excited
However I want to move over using the best practices to assure that I remain excited and not frustrated
My initial thoughts are to boot it up and doe the initial set up - to move my iPhoto library over and to use migration assistance to move the rest of my data files
Then to install all of the extra software that I can find the packages for from the original installation disks
And then finally to use migration assistant again to move over any software that I can not find original disks for (I've moved from Mac to Mac to Mac over and over and some of the software goes back to OS 9 (and won't run anymore I guess)
Is this a good way
OR
will I mess up doing it this way
OR
am I spending far too much time worrying about moving old problems over and would be better off to just turn MA loose and let it do its thing form the beginning?
BTW - mail crashes a lot on my existing system - pretty much everything else seems ok - except iPhoto is slow - hoping that the new Intel dual core will help that
LNMigration Assistant is not a general file moving tool. MA will migrate your Applications and Home folders transferring only your third-party applications. MA will transfer any application support folders required by your applications, your preferences, and network setup. You do not have a choice of what will be migrated other than the above. MA cannot determine whether anything transferred is compatible with Snow Leopard. I recommend you look at the following:
A Basic Guide for Migrating to Intel-Macs
If you are migrating a PowerPC system (G3, G4, or G5) to an Intel-Mac be careful what you migrate. Keep in mind that some items that may get transferred will not work on Intel machines and may end up causing your computer's operating system to malfunction.
Rosetta supports "software that runs on the PowerPC G3, G4, or G5 processor that are built for Mac OS X". This excludes the items that are not universal binaries or simply will not work in Rosetta:
Classic Environment, and subsequently any Mac OS 9 or earlier applications
Screensavers written for the PowerPC
System Preference add-ons
All Unsanity Haxies
Browser and other plug-ins
Contextual Menu Items
Applications which specifically require the PowerPC G5
Kernel extensions
Java applications with JNI (PowerPC) libraries
See also What Can Be Translated by Rosetta.
In addition to the above you could also have problems with migrated cache files and/or cache files containing code that is incompatible.
If you migrate a user folder that contains any of these items, you may find that your Intel-Mac is malfunctioning. It would be wise to take care when migrating your systems from a PowerPC platform to an Intel-Mac platform to assure that you do not migrate these incompatible items.
If you have problems with applications not working, then completely uninstall said application and reinstall it from scratch. Take great care with Java applications and Java-based Peer-to-Peer applications. Many Java apps will not work on Intel-Macs as they are currently compiled. As of this time Limewire, Cabos, and Acquisition are available as universal binaries. Do not install browser plug-ins such as Flash or Shockwave from downloaded installers unless they are universal binaries. The version of OS X installed on your Intel-Mac comes with special compatible versions of Flash and Shockwave plug-ins for use with your browser.
The same problem will exist for any hardware drivers such as mouse software unless the drivers have been compiled as universal binaries. For third-party mice the current choices are USB Overdrive or SteerMouse. Contact the developer or manufacturer of your third-party mouse software to find out when a universal binary version will be available.
Also be careful with some backup utilities and third-party disk repair utilities. Disk Warrior 4.1, TechTool Pro 4.6.1, SuperDuper 2.5, and Drive Genius 2.0.2 work properly on Intel-Macs with Leopard. The same caution may apply to the many "maintenance" utilities that have not yet been converted to universal binaries. Leopard Cache Cleaner, Onyx, TinkerTool System, and Cocktail are now compatible with Leopard.
Before migrating or installing software on your Intel-Mac check MacFixit's Rosetta Compatibility Index.
Additional links that will be helpful to new Intel-Mac users:
Intel In Macs
Apple Guide to Universal Applications
MacInTouch List of Compatible Universal Binaries
MacInTouch List of Rosetta Compatible Applications
MacUpdate List of Intel-Compatible Software
Transferring data with Setup Assistant - Migration Assistant FAQ
Because Migration Assistant isn't the ideal way to migrate from PowerPC to Intel Macs, using Target Disk Mode, copying the critical contents to CD and DVD, an external hard drive, or networking
will work better when moving from PowerPC to Intel Macs. The initial section below discusses Target Disk Mode. It is then followed by a section which discusses networking with Macs that lack Firewire.
If both computers support the use of Firewire then you can use the following instructions:
1. Repair the hard drive and permissions using Disk Utility.
2. Backup your data. This is vitally important in case you make a mistake or there's some other problem.
3. Connect a Firewire cable between your old Mac and your new Intel Mac.
4. Startup your old Mac in Target Disk Mode.
5. Startup your new Mac for the first time, go through the setup and registration screens, but do NOT migrate data over. Get to your desktop on the new Mac without migrating any new data over.
If you are not able to use a Firewire connection (for example you have a Late 2008 MacBook that only supports USB:)
1. Set up a local home network: Creating a small Ethernet Network.
2. If you have a MacBook Air or Late 2008 MacBook see the following:
MacBook (13-inch, Aluminum, Late 2008) and MacBook Pro (15-inch, Late 2008)- Migration Tips and Tricks;
MacBook (13-inch, Aluminum, Late 2008) and MacBook Pro (15-inch, Late 2008)- What to do if migration is unsuccessful;
MacBook Air- Migration Tips and Tricks;
MacBook Air- Remote Disc, Migration, or Remote Install Mac OS X and wireless 802.11n networks.
Copy the following items from your old Mac to the new Mac:
In your /Home/ folder: Documents, Movies, Music, Pictures, and Sites folders.
In your /Home/Library/ folder:
/Home/Library/Application Support/AddressBook (copy the whole folder)
/Home/Library/Application Support/iCal (copy the whole folder)
Also in /Home/Library/Application Support (copy whatever else you need including folders for any third-party applications)
/Home/Library/Keychains (copy the whole folder)
/Home/Library/Mail (copy the whole folder)
/Home/Library/Preferences/ (copy the whole folder)
/Home /Library/Calendars (copy the whole folder)
/Home /Library/iTunes (copy the whole folder)
/Home /Library/Safari (copy the whole folder)
If you want cookies:
/Home/Library/Cookies/Cookies.plist
/Home/Library/Application Support/WebFoundation/HTTPCookies.plist
For Entourage users:
Entourage is in /Home/Documents/Microsoft User Data
Also in /Home/Library/Preferences/Microsoft
Credit goes to Macjack for this information.
If you need to transfer data for other applications please ask the vendor or ask in the Discussions where specific applications store their data.
5. Once you have transferred what you need restart the new Mac and test to make sure the contents are there for each of the applications.
Written by Kappy with additional contributions from a brody.
Revised 1/6/2009
In general you are better off reinstalling any third-party software that is PPC-only. Otherwise update your software so it's compatible with Snow Leopard.
Do not transfer any OS 9 software because it's unsupported. You can transfer documents you want to keep.
Buy an external hard drive to use for backup. -
Time out of Time Capsule - even with Ethernet
My 500G Time Capsule since yesterday evening refuses to work for longer than a few minutes, which is far too little for any backup.
The problem first was seen when I used it with WiFi. I then connected the TC directly with ethernet to my MacBook. Initiated a backup. After some time, it refuses to respond any more.
Click on the TC icon in the Finder column view, and nothing comes up.
Try cd /Volumes/tcapsule in the Terminal, and the terminal window freezes.
Open the TC preferences and System Preferences freeze.
I tried resetting the TC with a paper clip.
I tried restarting the TC. After that, it works for a few more minutes, before it freezes again.
I tried removing the file com.apple.TimeMachine.plist.
I tried restarting the Mac umpteen times. It usually freezes as well when the TC is frozen.
I used Disk Utility to repair the Mac's harddisk.
I used Disk Utility to try to repair the image on the TC, dragging its icon to Disk Utility. However, it gives up - probably when the TC times out.
Does anyone have any idea what I could do in addition to those things, while keeping the old backups on the TC? I would prefer not to reformat the TC.
A new backup to third party Lacie HD worked fine, so I guess the Mac is ok, and the problem really is with the TC.Jolly Giant wrote:
some users solved their problems by going this route:
"Their problems"... Do you know of people, or did you find people who describe the same symptom as me, with a time out?
go system preferences > time machine and turn TM off. click on +change disk+ and select none.
next, delete this file HD/Library/Preferences/com.apple.TimeMachine.plist.
restart your machine, go system preferences > time machine and turn TM back on. click on +change disk+, re-select your backup volume und click +use for backups+.
Yep, that's pretty much what I did, as described in my initial post. I actually followed your exact steps again, but not luck.
download and install Time Machine Buddy if you don't have it already. start a backup and see what TM buddy reports.
Done that too, but the errors do not help me very much. A typical session may look like this:
Starting standard backup
Network destination already mounted at: /Volumes/tcapsule
Disk image /Volumes/tcapsule/Magnus Lewan’s MacBook_002332b4fbc4.sparsebundle mounted at: /Volumes/Backup of Magnus Lewan’s MacBook
Backing up to: /Volumes/Backup of Magnus Lewan’s MacBook/Backups.backupdb
Event store UUIDs don't match for volume: blanco
Node requires deep traversal:/ reason:must scan subdirs|new event db|
No pre-backup thinning needed: 23.55 GB requested (including padding), 24.83 GB available
Waiting for index to be ready (100)
And then nothing more.
The last one was somewhat more descriptive, but still no reason why things fail, and of course no suggested remedy:
Starting standard backup
Network destination already mounted at: /Volumes/tcapsule
Error while checking destination cookies: Error Domain=NSCocoaErrorDomain Code=260 UserInfo=0x100120690 "The file “.002332b4fbc4” couldn’t be opened because there is no such file." Underlying Error=(Error Domain=NSPOSIXErrorDomain Code=2 "The operation couldn’t be completed. No such file or directory")
Creating disk image /Volumes/tcapsule/blanko.sparsebundle
Error 22 creating backup disk image
Failed to create disk image
Backup failed with error: 20
It seems to first fail to read the previous sparsebundle and then it tries to create a new one. This may fail because the disk is full, but it should be able to open the previous one.
Maybe you are looking for
-
I just loaded a bunch of music from my CD library into iTunes in the hopes of loading it onto my iPod. The problem is now I can't figure out how to do it. Two issues... First it says that if I synch it will delete what is already on my iPod which I a
-
ISight camera is no longer recognized
iChat only allows me to audio chat and photobooth says there is no camera. Whats should i do?
-
Is there a way to retrieve deleted texts?
Is there a way to retrieve deleted texts and photos?
-
Hello, I recieved a Zen Neeon 6 gb for Christams from the kids and I have a few questions that do not seem to be in the documentation. . Is it possibel to select the opening screen. I want to open on the browse screen and it seems to always open on a
-
HP Pavilion dm4 3050us Entertainment Notebook Fingerprint scanner
Alright, so I just got my HP Pavilion dm4 3050us (Running Windows 7-Home Premium) a few days ago, and ever since I've been trying to figure out this fingerprint scanner. I just CANNOT figure out how to work it, or even open/start/launch it at all. It