PCCE 10.5 Lab cannot set PCCE Deployment Type

Hi All,
Now I am trying to install PCCE 10.5 in my lab using single UCS C220 High Density.
I already installed following applications:
1 Cisco Unified CCE Call Server
1 Cisco Unified CCE Data Server
1 Cisco Unified CVP Ops Console Server, co-located with a Cisco Unified CVP Call Server, Cisco Unified CVP Media Server, and Cisco Unified CVP VXML Server.
1 Cisco Unified CM
1 Cisco Unified Intelligence Center
1 Cisco Finesse
When I am trying set PCCE Deployment Type to "Packaged CCE: CCE-PAC-M1 Lab Only", I found following error:
"Error occurred--Internal Server Error. Try again later or contact your system administrator."
I already applied ICM 10.5(1) ES7 referring to CSCuq32014 to solve this problem. Unfortunately I am still have the same problem.
Please advise how to solve this problem.
Best regards,
Heribertus

Hi JT,
During this lab, I get an error message when I choose Deployment Type "Package CCE: CCE-PAC-M1 Lab Only". There is no error message when I choose "Package CCE: CCE-PAC-M1" and "UCCE 450 Agents Progger".
I found solution:
Step #1: Choose "UCCE 450 Agents Progger"
Step #2: Then I change it to "Package CCE: CCE-PAC-M1 Lab Only". I didn't get an error message again.
I am not sure, this is fail in validation rule or other things.
Thanks and best regards,
Heribertus

Similar Messages

  • Cannot delete last Deployment Type as it is referenced by a previously deleted Deployment Type

    Hi guys...
    I have previously created dependencies between two (2) separate Application's Deployment Types (DT) as such:
    "DT_A in Application_A" depends on
    "DT_B in Application_B"
    During some test procedures, we have deleted the whole of Application_A (along with all its DTs).
    Now, we are unable to delete DT_B as well as it complains that it is still being referenced by (the already deleted)
    DT_A. Obviously we can't delete Application_B as a whole as it is still complaining that
    DT_B is still being referenced.
    The References tab in
    Application_B still shows that it is still being referenced by Application_A even though searching from the Console as well as Get-CMApplication does not show any more of the deleted
    Application_A
    The last and only Revision in
    Application_B's Revision History cannot be deleted as its Delete button is greyed out.
    However, the View button can be clicked and it shows the historical revision during the time when Application_A still referenced Application_B.
    Any ideas on how we can delete Application_B ? Is deleting Applications and DTs via SQL Query possible ?

    Yup... got it done via Remove-WmiObject...
    1. First, find the offending Application_A still referencing the Application_B
    !!AND MAKING SURE IT IS THE CORRECT ONE!! via:
    Get-Wmiobject -Namespace "root\SMS\Site_PRI" -Class SMS_Application | Where-Object { $_.LocalizedDisplayName -eq "Application_A" }
    2. Once confirmed that it is the correct Application, remove it by piping to Remove-WmiObject via:
    Get-Wmiobject -Namespace "root\SMS\Site_PRI" -Class SMS_Application | Where-Object { $_.LocalizedDisplayName -eq "Application_A" } | Remove-WmiObject
    3. Delete the referenced Application_B as per normal procedure via the SCCM Console:
    Delete Deployments
    Delete Deployment Type(s)
    Delete Revision(s)
    Retire
    Delete Application
    Done.
     

  • Java.lang.SecurityException: Cannot set up certs for trusted CAs

    Hi,
    The application iam working on encrypts & decrypts files. The application is deployed on a standalone OC4j container on solaris 5.8. I have downloaded the following jar files
    jce1_2_2.jar
    sunjce_provider.jar
    local_policy.jar
    US_export_policy.jar
    and have declared them in the application.xml
    when i run the application i get the following exception.
    java.lang.ExceptionInInitializerError: java.lang.SecurityException: Cannot set up certs for trusted CAs: java.lang.SecurityException: Signer restraint check failed! at javax.crypto.SunJCE_b.<clinit>(DashoA6275) at javax.crypto.Cipher.a(DashoA6275) at javax.crypto.Cipher.getInstance(DashoA6275) at pdfDownload.jspService(_pdfDownload.java:215) [SRC:/pdfDownload.jsp:167] at com.orionserver[Oracle9iAS (9.0.3.0.0) Containers for J2EE].http.OrionHttpJspPage.service(OrionHttpJspPage.java:56) at oracle.jsp.runtimev2.JspPageTable.service(JspPageTable.java:317) at oracle.jsp.runtimev2.JspServlet.internalService(JspServlet.java:465) at oracle.jsp.runtimev2.JspServlet.service(JspServlet.java:379) at javax.servlet.http.HttpServlet.service(HttpServlet.java:853) at com.evermind[Oracle9iAS (9.0.3.0.0) Containers for J2EE].server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:721) at com.evermind[Oracle9iAS (9.0.3.0.0) Containers for J2EE].server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:306) at com.evermind[Oracle9iAS (9.0.3.0.0) Containers for J2EE].server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:767) at com.evermind[Oracle9iAS (9.0.3.0.0) Containers for J2EE].server.http.HttpRequestHandler.run(HttpRequestHandler.java:259) at com.evermind[Oracle9iAS (9.0.3.0.0) Containers for J2EE].server.http.HttpRequestHandler.run(HttpRequestHandler.java:106) at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:803) at java.lang.Thread.run(Thread.java:484)
    Pls advise, is there any other setting that needs to be done ?
    Thanks & Regards
    Arun

    Hi,
    I got the solution for this. JCE 1.2.2 is supported on JDK 1.4.1 and JDK 1.4.2, but both of them have different unrestricted policy jars. I was able to solve the problem once I downloaded the unrestricted policy jars for JDK 1.4.2 (which is used by BEA 8.1 SP5) from the following URL : http://java.sun.com/j2se/1.4.2/download.html
    Regards,
    Prashant Kale.

  • Exception: cannot set unrecognized property:

    Hi guys,
    I am doing a PoC of Connection between BPEL PM 10.1.3.4 running over WLS 9.2 SP3 calling a HelloWorld WebService (a very simple one without authentication or security) that is deployed over a WLS 10.3 server.
    The problem is when I execute the BPEL process and it invokes the partner link that pointos to my WebService I get an exception of that type below.
    Exception: cannot set unrecognized property: disable.must.understand on a Call object.
    I looked inside the logs of AdminServer, ManagedServer and Domain Server and the output files and nothing new came in from them.
    Any ideas? Please...
    The sourcecode of this PoC is here
    http://download.yousendit.com/Y1RyeW55VnN0TW14dnc9PQ
    receiveInput
    [2009/09/25 11:29:41] Received "inputVariable" call from partner "client" More...
    Assign_1
    [2009/09/25 11:29:41] Updated variable "Invoke_1_getGreeting_InputVariable" More...
    Invoke_1 (faulted)
    [2009/09/25 11:29:41] Faulted while invoking operation "getGreeting" on provider "HelloWorldServiceDefinitions".menos
    Daniel
    ORABPEL-00000
    Exception not handled by the Collaxa Cube system.
    An unhandled exception has been thrown in the Collaxa Cube system. The exception reported is: "cannot set unrecognized property: disable.must.understand on a Call object
         at oracle.j2ee.ws.client.dii.BasicCall.setProperty(BasicCall.java:490)
         at com.collaxa.cube.ws.wsif.providers.oc4j.jaxrpc.WSIFOperation_JaxRpc.setCallContext(WSIFOperation_JaxRpc.java:2769)
         at com.collaxa.cube.ws.wsif.providers.oc4j.jaxrpc.WSIFOperation_JaxRpc.invokeRequestResponseOperation(WSIFOperation_JaxRpc.java:1524)
         at com.collaxa.cube.ws.wsif.providers.oc4j.jaxrpc.WSIFOperation_JaxRpc.executeRequestResponseOperation(WSIFOperation_JaxRpc.java:1210)
         at com.collaxa.cube.ws.WSIFInvocationHandler.invoke(WSIFInvocationHandler.java:478)
         at com.collaxa.cube.ws.WSInvocationManager.invoke2(WSInvocationManager.java:437)
         at com.collaxa.cube.ws.WSInvocationManager.invoke(WSInvocationManager.java:251)
         at com.collaxa.cube.engine.ext.wmp.BPELInvokeWMP.__invoke(BPELInvokeWMP.java:826)
         at com.collaxa.cube.engine.ext.wmp.BPELInvokeWMP.__executeStatements(BPELInvokeWMP.java:402)
         at com.collaxa.cube.engine.ext.wmp.BPELActivityWMP.perform(BPELActivityWMP.java:199)
         at com.collaxa.cube.engine.CubeEngine.performActivity(CubeEngine.java:3698)
         at com.collaxa.cube.engine.CubeEngine.handleWorkItem(CubeEngine.java:1655)
         at com.collaxa.cube.engine.dispatch.message.instance.PerformMessageHandler.handleLocal(PerformMessageHandler.java:75)
         at com.collaxa.cube.engine.dispatch.DispatchHelper.handleLocalMessage(DispatchHelper.java:217)
         at com.collaxa.cube.engine.dispatch.DispatchHelper.sendMemory(DispatchHelper.java:314)
         at com.collaxa.cube.engine.CubeEngine.endRequest(CubeEngine.java:5765)
         at com.collaxa.cube.engine.CubeEngine.createAndInvoke(CubeEngine.java:1087)
         at com.collaxa.cube.engine.ejb.impl.CubeEngineBean.createAndInvoke(CubeEngineBean.java:133)
         at com.collaxa.cube.engine.ejb.impl.CubeEngineBean.syncCreateAndInvoke(CubeEngineBean.java:162)
         at com.collaxa.cube.engine.ejb.impl.CubeEngineBean_2rw8jy_ELOImpl.syncCreateAndInvoke(CubeEngineBean_2rw8jy_ELOImpl.java:75)
         at com.collaxa.cube.engine.delivery.DeliveryHandler.initialRequestAnyType(DeliveryHandler.java:547)
         at com.collaxa.cube.engine.delivery.DeliveryHandler.initialRequest(DeliveryHandler.java:464)
         at com.collaxa.cube.engine.delivery.DeliveryHandler.request(DeliveryHandler.java:133)
         at com.collaxa.cube.ejb.impl.DeliveryBean.request(DeliveryBean.java:95)
         at com.collaxa.cube.ejb.impl.DeliveryBean_uhics8_EOImpl.request(DeliveryBean_uhics8_EOImpl.java:279)
         at com.oracle.bpel.client.delivery.DeliveryService.request(DeliveryService.java:106)
         at jsp_servlet.__ngdoinitiate_ws._jspService(__ngdoinitiate_ws.java:517)
         at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
         at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
         at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
         at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:283)
         at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
         at com.collaxa.cube.fe.DomainFilter.doFilter(DomainFilter.java:126)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
         at weblogic.servlet.internal.RequestDispatcherImpl.invokeServlet(RequestDispatcherImpl.java:531)
         at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispatcherImpl.java:459)
         at weblogic.servlet.jsp.PageContextImpl.include(PageContextImpl.java:159)
         at jsp_servlet.__displayprocess._jspService(__displayprocess.java:1851)
         at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
         at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
         at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
         at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:283)
         at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
         at com.collaxa.cube.fe.DomainFilter.doFilter(DomainFilter.java:126)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
         at weblogic.servlet.internal.RequestDispatcherImpl.invokeServlet(RequestDispatcherImpl.java:531)
         at weblogic.servlet.internal.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:266)
         at com.collaxa.cube.fe.DomainFilter.doFilter(DomainFilter.java:222)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:42)
         at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3242)
         at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
         at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
         at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2010)
         at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:1916)
         at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1366)
         at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
         at weblogic.work.ExecuteThread.run(ExecuteThread.java:181)
    Exception: cannot set unrecognized property: disable.must.understand on a Call object
    Handled As: com.collaxa.cube.CubeException
    [2009/09/25 11:29:41] There is a system exception while performing the BPEL instance, the reason is "cannot set unrecognized property: disable.must.understand on a Call object". Please check the error log file for more infromation.
    Edited by: Daniel Ferreira Castro on 25/09/2009 12:20

    I think you took my comment out of context. I was referring to deployments on developer PCs to have a standalone version to play with. This is not common as it requires more PC power which not many people have.
    10g and 11g are different products. In 11g you are correct SOA Suite is installed on WLS, as there is no 11g oc4j. So in that respect I would agree that WLS as the app server is mainstream.
    In 10g I would have to disagree. It was a message that Oracle had to say that SOA Suite can be deployed on WLS and this was our stragic app server going forward. It would be a customer decision as to what path they would take. From my experience not many did this because the WLS version was 9.2 not the 10.3 which OSB ran on. There were limited customers to provide references on this architecture. Typically what we saw if customer were BEA customers they went down this path otherwise they went with oc4j. Oracle sold WebLogic Suite which included oc4j so from a licensing perspective they were covered, and technically they could run any Oracle product. For new licenses you needed WebLogic Suite as part of SOA Suite this does not mean that people deployed SOA Suite on WLS in 10g.
    10.1.3.5 certification with WLS was going to solve the version issue as it is going to be on 10.3, but 10.1.3.5 was release after 11g and the WLS certifications still hasn't been released.
    The 10g WLS deployment was never going to be like that in 11g so WLS customers would need the same kind of architectual changes and oc4j customer would have. The differnce being ops people would not need to learn oc4j so there would be less need for training.
    But I would like to clarify my comment was for stand alone deployments on developer PCs, this is not common to have the WLS deployment.
    cheers
    James

  • CatalogDeployer issue - "Cannot set header. Response already committed"

    Whenever we are trying to deploy any package we immediately get a 'deployment successful' message though the package is not deployed and remnains in the received for deployment queue. This is only found in the log 00000048 SRTServletRes W WARNING: Cannot set header. Response already committed.
    Very much appreciated if you could provide the resolution.
    We have a production service release tomorrow so we need assistance on this one asap. Thanks a lot

    You can not write to the response after you have forwarded the request to another servlet/JSP.

  • How to set the deployment directory ?

    Hi all,
    I am using Sun One Studio 3.0 with iWS6.0.
    For every new application that I write, compile and execute,
    it is getting deployed to the same
    directory.
    Because Sun One Studio is always using the same directory,
    for every application I have
    to manually delete the deployment directory.
    Is there any way to set different deployment
    directory for every new application that I write ?
    If yes, how to do this ?
    Thanks
    Swap

    I dont have the product installed, so I cannot try it right now. But I think the context root is part of the directory name in which the application is deployed. By default the context root is empty. If you change that, your application would be deployed in a different directory. To change context root, right click on WEB-INF node, and select "Properties" from the menu.
    Alternatively, you could try changing the directory name by right-clicking on the web.xml node under WEB-INF. You should see an iWS tab on the property sheet, where you could enter a directory name.

  • In FrameMaker 9.0.3 and 9.0.4, I cannot set tab stops for a style in the Paragraph Designer.

    In FrameMaker 9.0.3 and 9.0.4, I cannot set tab stops for a style in the paragraph designer. Here are the steps to dysfunction:
    1. In Paragraph Designer, for Tab Stops, click Edit. Edit Tab Stop dialog box opens, and the Paragraph Designer dialog box closes.
    2. Type value in New Position box.
    3. Click Continue. The Edit Tab Stop box closes.
    4. Open Paragraph Designer. No tabs are recorded.
    Discussion of a similar problem occured on this forum in June 2010. At that time, the resolution seemed to be to upgrade to 9.0.3. Has anyone else encountered this problem with these versions?
    Thanks.

    Hi, Arnis,
    Brilliant! Thanks so much. I only looked at the later discussions of that thread, which seemed to indicate the problem would be solved by an upgrade to 9.0.3.
    -Trish

  • When I click the iCloud button I get a browser with check boxes, not slider buttons and it does not have a "backup and storage" button.  So I cannot set up backup.

    When I open my iCloud browser it looks different than "normal." It shows the list with check boxes, not slider on-off buttons.  It dos not show a "storage and backup" button so I cannot set up my backup. What is wrong?

    If see something like the image below it's because you are looking at the iCloud settings on your Mac, not on an iOS device (which has sliders).  Storage & Backup isn't in the Mac settings because you cannot back up your Mac to iCloud.  Only iOS devices can back up to iCloud.  On a Mac, you can get information about your iCloud account storage by looking at the green usage bar at the bottom and by clicking the "Manage..." button on the bottom right.

  • When I try to create a calendar announcement in my iCloud calendar thru my PC / Outlook, it says 'the set of folders could not be opened. The information store could not be opened'. Can anyone help?  This means I cannot set any calendar events thru my PC.

    When I try to create an iCloud calendar announcement / event on my PC thru Outlook, I get the message 'the set of folders could not be opened.  The information store could not be opened'.
    I cannot set any calendar events for my shared calendar.  Can ayone help?

    If you upgraded to Windows 8 you may need to update the iCloud control panel for Windows to version 2.1 (see http://support.apple.com/kb/TS4463).

  • Cannot set Windows 7 default printer in Boot Camp

    I discovered today that I cannot set a default printer in Windows 7.  I right click, and try to make one of the printers default but there is no check mark.  One of the programs that I use says I do not have a printer installed. 
    I can print to my printers using Word by selecting the printer that I want but cannot select a default in control panel.
    If I access Windows programs using a VM Fusion, the program that says there is no printer installed in boot camp, does not give be this message and I can select a printer.  BTW, I have never been able to select a "default printer" using VM Fusion.
    The only thing unusual is I had to reactivate Windows for no apparent reason last week and I cannot select all of the Themes available in the personalize menu. 
    It is difficult to pinpoint when the printer issue started because I mainly access my Windows programs through VM Fusion.  I am guessing the changes happened when I had to reactivate Windows
    I am away from my iMac currently and was wondering if anyone has experienced this and/or have a suggestion.?
    Thanks,
    Roy

    Update.
    Apparently this is a Windows Registry issue.  Looks as if there is a VM Fusion driver set as default (thinprint??)  I cannot delete or modify this registry key.  A new profile solves this issue and I will have to copy everything over to the new profile, if I cannot get this registry key issue solved.  I will post on a Microsoft board to see if there is a solution.
    Roy

  • Cannot set status of Urgent Change after manual transport

    Hi all,
    We are usng CHARM in Solution Manager 7.1 for import to the SAP ECC (EHP6) systems.
    I cannot set the status of the Urgent Change document (ZMHF) to status "To be Tested" after the transports were manually released and manually imported to the ECC QA system.
    When I use action "Pass Urgent Change to Test", the system stopped with error "Not all task are yet released" and will not change the status .
    Based, on the Task List log, the system started the release process although no transports were released.
    Is there any way that I can update the status of the Urgent Change document to "To be Tested"?
    I tried program CRM_SOCM_SERVICE_REPORT but still did not change the status.
    Any suggestion?
    Thanks,
    Tess

    Hi Venu,
    have a look under System Administration - System Configuration -- Knowledge Management -- Configuration --Content Management -- User Interface -- Commands -- UI Command Groups -- StatemanagementGroup.
    See Java class: com.sapportals.wcm.rendering.uicommand.cm.UIStatemanagementGroupCommand. Take the class and decompile this and everything needed around to understand how this class works.
    Then you can choose to extend this CommandGroup to also have a command "Resubmit for Approval" or you can implement your own UI Command only for resubmitting (you will also have to activate your command (group) by settings within the configuration).
    On the other hand, if all this is completely new to you, I'm a bit sceptical if the task isn't a bit too big as a first task on KM implementation topics...?
    Hope it helps
    Detlev

  • [Solved?] VLC won't play audio -- cannot set buffer duration

    I can't play sound in VLC. I have tried the default and the ALSA outputs. I know ALSA works, because mpg123, speaker-test, and rdesktop's sound all work. (Saying that, I can't tell if mpg123 uses alsa or not - rdesktop does though)
    Attempting to play something in VLC gives me some rather cryptic errors. What follows is the output of "vlc -v" and an attempt to play a video with sound. I have split the "code"-tag just before the actual error output for clarity and ease of scanning.
    VLC media player 2.0.7 Twoflower (revision 2.0.6-54-g7dd7e4d)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/audio_output/libportaudio_plugin.so' (libportaudio.so.2: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/audio_output/libjack_plugin.so' (libjack.so.0: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/services_discovery/libmtp_plugin.so' (libmtp.so.9: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/notify/libxosd_plugin.so' (libxosd.so.2: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/visualization/libgoom_plugin.so' (libgoom2.so.0: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/visualization/libprojectm_plugin.so' (libprojectM.so.2: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/codec/libtwolame_plugin.so' (libtwolame.so.0: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/access/libvcdx_plugin.so' (libvcdinfo.so.0: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/access/libaccess_jack_plugin.so' (libjack.so.0: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/access/libaccess_dv_plugin.so' (libavc1394.so.0: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/access/libaccess_mtp_plugin.so' (libmtp.so.9: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/video_output/libaa_plugin.so' (libaa.so.1: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/video_output/libcaca_plugin.so' (libcaca.so.0: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc warning: cannot load module `/usr/lib/vlc/plugins/control/liblirc_plugin.so' (liblirc_client.so.0: cannot open shared object file: No such file or directory)
    [0x8eb108] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface.
    [0x7f1e6cc01bf8] mkv demux warning: MKV/Ebml Parser: m_el[mi_level] == NULL
    [0x7f1e6cc01bf8] mkv demux warning: MKV/Ebml Parser: Up cannot escape itself
    Fontconfig warning: FcPattern object size does not accept value "0"
    [0x7f1e68c068a8] alsa audio output error: cannot set buffer duration: Invalid argument
    [0x7f1e68c068a8] pulse audio output error: PulseAudio server connection failure: Connection refused
    [0x7f1e68c068a8] oss audio output error: cannot open audio device (/dev/dsp)
    [0x7f1e68c068a8] main audio output error: no suitable audio output module
    Fontconfig warning: FcPattern object size does not accept value "0"
    [0x7f1e6cc02b68] main decoder error: failed to create audio output
    I have reproduced this with the same result using 'sudo vlc-wrapper' and I am added to the 'audio' group.
    I have no idea where to start with this issue, I've tried googling but it seems that only one person has ever had this issue before (if Google is to be considered a reputable source), and he was running his own VLC build. I am running the build "pacman -S vlc" gave me. If anyone could point me in the right direction on this issue I'd be grateful.
    Edit: This is my /etc/asound.conf. I have no idea what any of this means, at this point it's fill-in-the-blanks wiki copypasta (Edit2: The purpose of this file is to try to stop alsa from sending all my sound through a disconnected HDMI instead of the speakers)
    # Use PulseAudio by default
    #pcm.!default {
    # type pulse
    # fallback "sysdefault"
    # hint {
    # show on
    # description "Default ALSA Output (currently PulseAudio Sound Server)"
    #ctl.!default {
    # type pulse
    # fallback "sysdefault"
    pcm.!default {
    type plug
    slave.pcm {
    @func getenv
    vars [ ALSAPCM ]
    default "hw:Generic_1"
    # vim:set ft=alsaconf:
    Last edited by Score_Under (2013-08-02 23:23:27)

    Situation update:
    1. I didn't need my asound.conf like that -- I should have used pulseaudio in the first place, I was unaware that ALSA does not allow more than one program to use the sound device at the same time, whereas pulseaudio is used to mix sounds.
    2. VLC works fine on PulseAudio. No idea why it failed on ALSA!
    Last edited by Score_Under (2013-08-02 23:22:45)

  • Need help on  ORA-02074: cannot SET NLS in a distributed transaction

    Hi All,
    I am Writing a plsql Code like this
    DECLARE
    op_job_id NUMBER;
    op_object_version_number NUMBER;
    x_job_definition_id NUMBER;
    op_name VARCHAR2(1000);
    L_VERIFY_FLAG VARCHAR2(1);
    l_error_message VARCHAR2(2000);
    BG_ID NUMBER;
    lv_job_group_id APPS.per_job_groups.job_group_id@SYSTEM_LINK_VISMA%TYPE;
    CURSOR C1 IS SELECT * FROM EBS_PER_JOBS_STG;
    BEGIN
    FOR H1 IN C1
    LOOP
    BEGIN
    IF H1.BUSINESS_GROUP_NAME IS NOT NULL THEN
    SELECT BUSINESS_GROUP_ID,job_group_id INTO BG_ID,lv_job_group_id
    FROM APPS.PER_JOB_GROUPS@SYSTEM_LINK_VISMA
    WHERE DISPLAYED_NAME=H1.JOB_GROUP_NAME;
    END IF;
    EXCEPTION
    WHEN OTHERS THEN
    L_VERIFY_FLAG := 'E';
    l_error_message := 'Entered Job Group Name is Wrong';
    END;
    -->> JOB GROUP ID <<--
    APPS.hr_job_api.CREATE_JOB@SYSTEM_LINK_VISMA
    (p_business_group_id => BG_ID
    ,p_date_from => H1.DATE_FROM
    ,p_approval_authority => H1.APPROVAL_AUTHORITY
    ,p_emp_rights_flag => H1.EMP_RIGHTS_FLAG
    ,p_benchmark_job_flag => H1.BENCHMARK_JOB_FLAG
    ,p_job_group_id => lv_job_group_id
    ,p_job_information1 => H1.JOB_INFORMATION1
    ,p_job_information2 => H1.JOB_INFORMATION2
    ,p_job_information3 => H1.JOB_INFORMATION3
    ,p_job_information4 => H1.JOB_INFORMATION4
    ,p_job_information5 => H1.JOB_INFORMATION5
    ,p_job_information6 => H1.JOB_INFORMATION6
    ,p_job_information7 => H1.JOB_INFORMATION7
    ,p_segment3 => H1.JOB_CODE --JOB_CODE
    ,p_segment6 => H1.JOB_NAME --JOB_NAME
    ,p_job_id => op_job_id
    ,p_object_version_number => op_object_version_number
    ,p_job_definition_id => x_job_definition_id
    ,p_name => op_name);
    dbms_output.PUT_LINE('OUTPUT JOB NAME CREATED : '||op_name);
    END LOOP;
    EXCEPTION
    WHEN OTHERS THEN
    dbms_output.PUT_LINE('Error Message Is: '||SQLERRM);
    END;
    i am running it in Another database Using database link connecting to Apps.
    when i am running it am getting the following Error:
    Error Message Is: ORA-02074: cannot SET NLS in a distributed transaction
    ORA-06512: at "APPS.HR_KFLEX_UTILITY", line 2423
    ORA-06512: at "APPS.HR_KFLEX_UTILITY", line 2380
    ORA-06512: at "APPS.PER_JBT_UPD", line 468
    ORA-02074: cannot SET NLS in a distributed transaction
    ORA-06512: at "APPS.HR_JOB_API", line 878
    Please help me on this, this is quite urgent to me.
    thanks
    sri

    Please see these docs.
    ORA-02074: Cannot SET NLS in a Distributed Transaction [ID 556391.1]
    Portal Used To Call PO_CHANGE_API1_S: ORA-20001: ORA-02074: Cannot SET NLS In A Distributed Transaction [ID 561246.1]Why are Concurrent Programs Calling FND_GLOBAL.APPS_INITIALIZE Using DBLinks Failing? [ID 466800.1]
    ORA-02074 when Executing set_nls over a DB Link [ID 132679.1]
    Thanks,
    Hussein

  • Viewlink between Custom VO "Cannot set user query to view"

    We have an application where we have extended custom VO and EO’s to get data from flat files. It all looks fine till we create a viewlink for a LOV with two related VO’s. The viewlink VO fails we get message of the form -Cannot set user query to view "CustomVO1" because it is a destination in a view link”. Are there any methods to override in the custom VO/EO or any parameter to be added to configs. Has someone tried this out

    Thanks for the update and for sharing the solution!
    Regards,
    Hussein

  • Users are not able to use Outlook 2010 to view free/busy information and cannot set Out Of Office automatic reply

    Hi All,
    Please help me.
    I have an issue where users are not able to use Outlook 2010 to view free/busy information and cannot set Out Of Office automatic reply. But they are can set Out Of Office automatic reply from OWA. My exchange server is Ms Exchange 2010.
    The test E-mail AutoConfiguration failed with this error:
    Autodiscover to https://mydomain.com/autodiscover/autodiscover.xml starting
    GetLastError=12175; httpStatus=0.
    Autodiscover to https://mydomain.com/autodiscover/autodiscover.xml Failed (0x800C8203)
    Autodiscover to https://autodiscover.mydomain.com/autodiscover/autodiscover.xml starting
    GetLastError=12007; httpStatus=0.
    Autodiscover to https://autodiscover.mydomain.com/autodiscover/autodiscover.xml Failed (0x800C8203)
    Local autodiscover for mydomain.com starting
    Local autodiscover for mydomain.com Failed (0x8004010F)
    Redirect check to http://autodiscover.mydomain.com/autodiscover/autodiscover.xml starting
    Srv Record lookup for http://autodiscover.mydomain.com/autodiscover/autodiscover.xml Failed (0x80072EE7)
    Srv Record lookup for mydomain.com starting
    Srv Record lookup for mydomain.com Failed (0x8004010F)
    Any idea?
    Thanks,
    Pieter

    OK.
    Please follow this step.
    1. As you said you are in coexistence step , so for now all endpoint already point to Exchange 2010 right?
    2. Check legacy owa redirect that you already configure
    3. In Exchange 2010 , Make sure that you already configure "Autodiscoverinternaluri" by this command set-clientaccessserver -identity "servername" -autodiscoverinternaluri
    https://autodiscover.domain.com/autodiscover/autodiscover.xml. and don't forget to create autodiscover record in DNS
    4. in Exchange 2010 , Make sure that you already configure "EWS" path by this command set-webservicesvertualdirectory -identity "XXX\Default web site name" -internalurl
    https://yourinternalurl/EWS/Exchange.asmx -externalurl https://yourexternalurl/EWS/Exchange.asmx
    5. don't forget to replicate freebusy from Exchange 2003 to Excahnge 2010 via public folder.
    You error look like client cannot get autodiscover process please check it again.

Maybe you are looking for