PCI 6528 DO/I Problem

Hello,
I bought two NI cards very recently, the first one a PCI 6024E is perfeclty working but the other one a PCI 6528 does not work at all.
I plugged this very last card in 3 differents PC but i see nothing on digital output from port 3 to port 5 from MAX control panel test.
i'm using an SCB100 and i measure only the 5V on pin 49&99 even if i not use the SCB100.
The LED on the card is always lit.
I supposed the problem comes from my card but i want to be sure, before doing anything else. My card is only one week old
Thank you for your help
Configuration :
NI-DAQmx driver software 9.02 (sent with the PCI 6528 card)
Windows 7/XP

Hi,
The SSR is like a switch that you would have added between your power supply and your load (a LED, a drive, etc).
For each line of each port you have 2 pins PX.Y+ and PX.Y- for example, port 3 line 1 : you get P3.1+ and P3.1-, then you'll have to connect your load and the power supply between these pins.
Regards,
Da Helmut
Pièces jointes :
port.PNG ‏30 KB

Similar Messages

PCI-6528 question

Hi, Guys:
I have almost zero experience with Digital I/O - is it possible to do pulse width modulation with a PCI-6528?
Sorry it's dumb question, but like I said, I have about zero experience doing Digital I/O.
Bill
(Mid-Level minion.)
My support system ensures that I don't look totally incompetent.
Proud to say that I've progressed beyond knowing just enough to be dangerous. I now know enough to know that I have no clue about anything at all.
Solved!
Go to Solution.

billko wrote:
It doesn't need to be precise timing, do you think maybe I can do a brute force software-timed solution? I was hoping for a more elegant solution?
I've done it using counters... with DO its possible, consider using 'regeneration mode' and 'dynamically updating user buffer data' should be selected.
For analog output, 'dynamically updating user buffer data' is explained here. For 'regeneration mode' refer this. See if you can club these together.
I am not allergic to Kudos, in fact I love Kudos.
Make your LabVIEW experience more CONVENIENT.
Attachments:
LabVIEW_code_version 8.5.vi ‏364 KB

Accessing PCI-6528 from RT board (PCI-7041)

Hello everyone,
I would like to access &/or control my PCI-6528 board from my PCI-7041/6040E RT board. What possible methods are available for me to control the DIO on the the 6528? (I would like to avoid using the DIO on the 7041 daughter board if possible).
thanks
David

Hi David,
That's a great question. It would be a logical conclusion that since the PCI-7041/6040E is in the PCI bus that it could offer Real-Time control to the other cards in the PCI bus.
Unfortunately though, the PCI-7041/6040E
can only offer Real-Time control for the one daughter board directly
associated with it. All of the other cards would require talking
through the normal PCI bus and would lose any Real-Time capabilities.
I hope this helps you better understand what's going on.
Regards,
Otis
Training and Certification
Product Support Engineer
National Instruments

MSI Big Bang xPower II PCI-e 3.0 Problem

Hey Guys
I´ve got a big problem with my Big Bang Xpower II Mainboard. Although i´ve got at PCI-e compatible (Gigabybte GTX760 OC) which is placed in PCI-e Slot 1 and PCI-e Gen 3 activated my Board doesn´t activate PCI-e 3. I´ve already tried to install the UEFI on several ways but nothing helped.
My specs:
Mainboard: MSI Big Bang xPower II
CPU: Intel I7 4820k
VGA: Gigabyte GTX760 OC
Soundcard: Creative Soundblaster Z
RAM: Crucial Ballistix Tactical 16GB 1866MHz
sry if there are Mistakes my english is not so good because im from Germany and and im still a student
thanks for your help

Aha, but how windows changes will affect BIOS PCI-e version reading?
etc: this one which you said:
Quote
You can see the PCI-e Version activated before the Xpower BIOS Screen shows off (the where it show all data about the ASMedai chip ...
or this still shows 2.0 during bios post screen?

Linksys PCI cards and WLC problems

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:Standardowy;
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;
mso-fareast-language:EN-US;}
Hi,
I have Linksys
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:Standardowy;
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;
mso-fareast-language:EN-US;}
WMP200 and WMP54G Wi-Fi PCI cards installed on PC.
My infrastructure is WLC 2106 and two APs 1231G and one 1242G.
The problem is that the cards have problem with connection to WLAN.
The broadcast SSID must be enable then the cards connect to WLAN otherwise is a problem with connection.
When the card is connected but connection is unstable and poor.
The cards have the newest firmware installed.
Has anyone encountered a similar problem?
Kamil

Hi Kamil,
Have you associated other types of clients with these AP's? If so, do they perform better?
You might want to start by checking the status of the poorly performing client on the controller while it's connected:
monitor -> clients
You'll primarily be interested in the RSSI and SNR. The other counters such as 'excessive retries' should be observed as well.
Also check the AP's radio interface stats. Check for excessive interference or channel utilization.
This is a very helpful doc that you may want to check out:
Unified Wireless Network: Troubleshoot Client Issues
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00809d45a2.shtml
Let us know if any of this helps.

MS-6528 and KINGSTON problem!!!!

I greet
I am owner two modules Kingston KVR133x64C2 / 512 and MS-6528
unfortunately after installation of their on my plate the MSI 845 Pro 2 (MS -6528 ver.1.0) the mistakes are , the windows does not it want to enter ,and this similar. mainboar has the newest BIOS.
modules do not it inflict no problems individually there now they do not it want to walk together.they do not it accept no different memories also ( also different anomalies step out).they do not it want to work in duel,only solo
what be to possibly this cause ?(
I from mountain thank for pane and exhausting answer.
I greet szymek

Try looking in your boards' manual to find out how many banks it can hanle. Most 512MB ram is double sided =circuit stuff on both sides of the stick. Each side with stuff on it is a "bank". Look at your ram & see if there is circuit stuff on both sides. If so, is takes up 2 banks. The intel chipset on your board usually only supprorts 4 banks, but the board itself may only support 3 banks, regardless of the number of ram slots on the board. 128MB & some 256MB ram can now be found single sided. Your board might max out at 768MB. You will have to find out more about your mother board to make sure you are not going over the max banks.

Creative audio pci ensoniq (es1371)(es1373) problems for win 2k

i have a problem...my card is in and i have a driver that is signed by microsoft and everything but when i try to play any sound it just is silent

No sound from ES37 Creative Audio PCI after resuming from Standby. Running Win2K Pro.
Restarting allows audio to play normally. Checked drivers after rebooting and after resuming from Standby: no differences in driver listed in the Settings/Sounds and Multimedia/etc. Any ideas?

P43 Neo - PCI wireless LAN performance problems

Hi,
i recently installed the Neo P43 Board. Everything runs fine so far, except PCI wireless LAN (maybe more, it's the only PCI card I use). I already updated the BIOS to 1.6 but it doesnt fix it.
I tried 2 different WLAN cards (1 Realtek and 1 Ralink). Both of them basicly work, but the transfer rates are painfully slow although the connection quality is reported as good enough.
Anyone else having issues?

How low are the transfer rates?
It varies a bit but most of the time very low (as low as 1kbps or sometimes not working at all)
What are you connected to (Router?, What kind of Router)?
Connected to a router. It's a "Speedport" router, I think they are manufactured by Siemens.
When you talk about the transfer rate, do you mean the transfer rate that you get when you try to copy files to another system in a Wireless network?
I mean downloading files from the Internet over the router, or generally the connection to the router (like status page).
The Ralink card used to work just fine in my older PC with an Athlon XP / Nforce Chipset (and several other PCs), but on the Neo P43 makes problems with both, the Ralink and the Realtek card.
I'm not absolutely sure it is the board that makes these problems, but I can't think of any other source for this problem anymore.

Standby and PCIE 2.0 x16 problem

Good day Forum,
I have encountered 2 issues with my setup (I will list the setup specifications below).
Standby issue: My computer is unable to go S1 nor S3 standby despite having a new operating system installed. Power settings set at Maximum Performance for Windows 7. When I clicked 'Sleep', the system will power down but it will power up again (without having the display shown). I have ruled out USB issues because I have taken out all USB peripherals connected to it right before it shuts down from standby and connected back again after it powered up.
PCIE issue: My PCIE 2.0 x16 graphic card is slots into the blue coloured PCIE 2.0 x16 slot. There are 2 PCIE-based cards which are connected to the motherboard via the PCIE slot but they are not connected to the 2nd PCI 2.0 x16 slot (hence, no reason for the speed to drop to x8). The issue here is not concerning the bandwidth of my graphics card but merely a question of curiousity as to why the interface speed drops from PCI-E 2.0 x16 to PCI-E x16 (v1.1). Any ideas? Here are some of the screenshots I took before and after:
Before:
After:
Specification:
Intel i7-860 (2.8GHz)
MSI P55-GD85
Palit GTX570 1280MB
4x2GB RAM (DDR3-1333MHz)
Hauppauge HVR-2200
Auzentech X-Fi Prelude
Intel Pro 1000PT
2xSamsung F3 1TB (HD103SJ)
Steelseries Xai Mouse
Microsoft Digital 3000 Keyboard
Seasonic M12 700W

Quote from: NovJoe on 13-June-11, 10:44:40
To answer your second query, the following is extracted from MSI's website on your board's detail specifications.
Slots
• 2 PCI Express gen2 x16 slots
- If two graphics cards are installed at PCI_E1 & PCI_E2 slots, these two PCIE x16 lanes will auto arrange from x16/ x0 to x8/ x8
- supports ATI® Crossfire™ & NVIDIA SLI
• 1 PCI Express gen2 x1 slot (blue)
• 1 PCI Express gen1 x1 slot
• 2 PCI slots, support 3.3V/ 5V PCI bus Interface
http://www.msi.com/product/mb/P55-GD85.html#?div=Detail
Nope this is not related to his query[see his screenshots]
Quote from: Christine_Henri on 13-June-11, 09:38:24
PCIE issue: My PCIE 2.0 x16 graphic card is slots into the blue coloured PCIE 2.0 x16 slot. There are 2 PCIE-based cards which are connected to the motherboard via the PCIE slot but they are not connected to the 2nd PCI 2.0 x16 slot (hence, no reason for the speed to drop to x8). The issue here is not concerning the bandwidth of my graphics card but merely a question of curiousity as to why the interface speed drops from PCI-E 2.0 x16 to PCI-E x16 (v1.1). Any ideas? Here are some of the screenshots I took before and after:
Before:
After:
That's suppose to be. It's self adjust pci-e [1.xx <==> 2.xx] depend of VGA power needs.
When the VGA works in higher performance mode then will be auto switched to pci-e 2.0 automatically.
Quote from: Christine_Henri on 13-June-11, 09:38:24
Standby issue: My computer is unable to go S1 nor S3 standby despite having a new operating system installed. Power settings set at Maximum Performance for Windows 7. When I clicked 'Sleep', the system will power down but it will power up again (without having the display shown). I have ruled out USB issues because I have taken out all USB peripherals connected to it right before it shuts down from standby and connected back again after it powered up.
A new BIOS can help with this. If you already use latest BIOS for your mainboard, then you can ask msi about it here for further beta bios: http://support.msi.com/
P.S: Try turn off/Disable the "EuP 2013" BIOS option 1st, then retest

PCI-1422 Windows7 32bit Problems

I have a legacy program that I am trying to port from WindowsXP to 32bit version of Windows7. This program is based on the PCI-1422 frame grabber.
For historical purposes, I have to use NI-IMAQ version 2.5.3, which installs version 2.0.3.17 of NI-MAX
From a clean build of Win7 x32, I can install NI software, and the old application which creates correct camera definition files.
When I add the frame grabber card, Windows device manager is happy... the card is correctly identified and seems to use driver files which match the old WinXP install.
When I look at the card with NI-MAX, the camera correctly appears in the configuration list. If I highlight Channel 0 device and run 'Diagnostic' all tests seem to pass correctly. (Again the displayed output matches the results from the same operation on the old WinXP box)
However if I try to 'Snap' or 'Grab' a frame, I get the following error box: Title = 'Acquisition Error'   and there is NO TEXT in the error description, only a yellow ! warning icon.
(The legacy program performs all controlling functions via two other PCI cards, but halts when trying to grab a frame as well. The above behavior can be seen with or without these additional PCI cards)
I have tried both installing and executing the EXE files with or without 'Run as Admin' and/or 'WinXP SP3 compatibility mode'. In some cases, the available camera list disappears, but nothing I have done has been succesful at grabbing a frame from the camera.
Any suggestions about compatibility and/or why the error box is missing all text?
Thanks in advance,
Jim

Good questions...
I have been asked to 'upgrade' a commercial system that was developed 10 years ago. The system works currently... an XP based system with old frame grabber.   I was asked if I could upgrade the PC, because of concerns of PC failure with a 10 yr old box. We found a new motherboard that supports the necesary 3 PCI slots for frame grabber, and newer CPU of course.
The question remains however, can we migrate to Win7, or...   do we try to install WinXP on the new PC hardware, with the older interface cards. To add to the difficulties, the original company than produced the software is no longer in business. Fortunately I have remained in contact with some of the developers that are giving me some support, but they haven't supported the product for years either.
The basic issue remains... hardware and software that worked on XP, has been migrated. The devices appear in some sense to be detected correctly. But the critical important issue, grabbing a frame from the camear, fails. What can be done?

Soundblaster X-Fi Xtreme Gamer PCI 7.1 driver problems

Hey everybody,
I?ve got a problem with the driver for my soundcard and Windows 7. I try to install the vistadriver on my win 7 and everytime my system freeze at 89%, I try it with the cd drivers and with the newest driver from the homepage.
I try it with the install exe and other ways, everytime totalfreeze. Have somebody an idea what the problem could be?
Maurawani

Have you tried safe mode?
If this is still not working, please contact our Customer Support for further assistance.

Calling dll of Leetro MPC08 PCI motion controller card problems.

Hi,
I have been trying to develop an application using Labview 8.5. I need to control a motorized linear stage which uses the Leetro MPC08 PCI motion controller card. The manufacturer gave me example VIs which I configure to call "c:\windows\system32\MPC08.dll". About four months ago, I remembered that i tested them and they seemed to work somehow (but I did not finish the full test since i was busy doing other things). Nevertheless, when I got back to continue my development a few days ago, i just could not get the same old VIs to work. I could only get one library function of the card to work which is the "auto_set" which returns "4" which is the number of axes that the card can control. The next function I need to call is "init_board" but this one keeps returning "-3". The manual indicates that any negative number returned means there has been something wrong. I would guess it is "PCI initialization fails" but honestly do not know for sure. Can anyone help? My computer is a PC running windows XP.
Thanks in advance for any kind help offered.

Hi,
Wrapped VISA call means that the SubVI contains a set of VISA calls.
If you are calling the VI's individually it is possible that the VI's need to pass a reference to each other, so they might not work if run individually. Hard to know without the DLL docs, so to speak. It could be possible that there is no need to pass references between subVI's.
Direct VISA calls are probably not necessary if the device runs with the vendors software. The main goal was to verify functionality with either VISA or vendor app.
Ok I was looking at the Leetro web site, you can forget the VISA stuff as it is a PCI card, duh... you said that at the begining. :-)
The manual says Win2000 or XP. is this being run on two different systems?
Mark
Mark Ramsdale

PCI-6115 external conversion problem

Hello
I have following problem with 6115 card:
When i try to collect samples using external TTL generator everything is ine until I lower the signal frequency from generator to less than 2.5kHz. Then the sampling timing goes out the window. Does anyone had same problem and solved it somehow? I'd be gratefull for any suggestions.
Best Regards
Maciej

P.S
I'm using following code:
    i16 iStatus = 0;
    i16 iRetVal = 0;
    i16 iDevice = 1;
    i16 iChan = Channel;
    i16 iStartTrig = 0;
    i16 iExtConv = 2;
    i16 iGain = 1;
    u32 ulCount = il_prob;
    f64 dGainAdjust = 1.0;
    f64 dOffset = 0.0;
    i16 iSampTB = 0;
    u16 uSampInt = 0;
    i16 iDAQstopped = 0;
    u32 ulRetrieved = 0;
    i16 iIgnoreWarning = 0;
    i16 iYieldON = 1;
    iRetVal = NIDAQErrorHandler(iStatus, "Select_Signal",
     iIgnoreWarning);
    iStatus = DAQ_Config(iDevice, iStartTrig, iExtConv);
    iRetVal = NIDAQErrorHandler(iStatus, "DAQ_Config",
     iIgnoreWarning);
    iStatus = DAQ_Start(iDevice, iChan, iGain, piBuffer, ulCount,
     iSampTB, uSampInt);
    iRetVal = NIDAQErrorHandler(iStatus, "DAQ_Start", iIgnoreWarning);
    iRetVal = NIDAQErrorHandler(iStatus, "DAQ_Check", iIgnoreWarning);
    iStatus = DAQ_VScale(iDevice, iChan, iGain, dGainAdjust, dOffset,
     ulCount, piBuffer, pdVoltBuffer);
    iRetVal = NIDAQErrorHandler(iStatus, "DAQ_VScale",
     iIgnoreWarning);
    iStatus = DAQ_Config(iDevice, 0, 0);
    iStatus = Select_Signal(iDevice, ND_IN_CONVERT, ND_INTERNAL_TIMER,
     ND_LOW_TO_HIGH);

New Realtek PCI-E Ethernet Drivers problem

Win7 32/64: 7.012.0211.2010
Update Date 2010-02-26
tried to update to this driver, previous drivers have auto installed when opened but not this one, how do i install please
click the folder opt foe 32bit w7
and get the following
text file
security catalouge
setup information
system file
app exe
app exe
when i click on system file, it appears i donot have a program to open a sys file, never had this totally lost. need easy to follow advice on how to install please
using msi x58 board windows7 32 bit

Quote from: [email protected] on 08-March-10, 22:23:15
blaise thanks for the warning
mike prev drivers have autoinstalled using run in the download options do you know why this is no longer?
No probelm there mate, people who did manage to install them found that Windows would blue screen on boot until they rolled back to the previous version via Safe mode. Although I don't use my Ethernet ports ATM (currently using a prepaid USB wireless stick - long story), I tried to install the drivers a while ago and found they wouldn't update the system no matter how I tried..

6533-pci-32-hs ni-daq Windows NT

On Windows NT it's not possible to allocate a nidaq buffer of more than
64MegaBytes for output porpouses!.
Be aware!
Phil

Hi Vinay,
Let's first try installing the latest DAQ driver for your PCI-6528 and Windows NT. Let me know if this works. I have provided the download link below.
NI-DAQmx Version 7.5 for Windows 2000/NT/XP
http://digital.ni.com/softlib.nsf/websearch/CF7ECCEA4C4CC7DE86257038004D88AE?opendocument&node=13207...
As for your PCI-6528 that is not reading a digital high input, try swapping this nonworking PCI-6528 with the working PCI-6528 from your desktop PC. This will help determine whether or not that specific PCI-6528 card is the problem.
What other National Instruments software are on these computers (LabVIEW, LabWindows/CVI, etc)? Please include their versions, too.
Allen
National Instruments

PCI 6528 DO/I Problem

Similar Messages

Maybe you are looking for