PCI/AGP divider for KT6 Delta

hi,
i want to ask at which FSB does the divider for the KT6 Delta motherboard kicks in?
I'm trying to overclock an AMD XP 2400+ without unlocking the multiplier.
Thanks

thanks, i had just tried out the pin-mod guide which allows me to choose other multipliers...now my system is clocked at 2255mhz with 13.5x and 166mhz.
however, i think my maxtor Sata drive didn't like the increased speed. I was greeted with some disk errors but i was able to start winxp normally, run programs as usual. Any help in this?

Similar Messages

PCI/AGP Divider

Hi,
I need a confirmation, is the PCI/AGP divider always 3 no matter what the fsb is? Or is it 4 over 133fsb?
Or is it related to memory divider (and how)?
It is for 645 Ultra version 1 MS-6547.
Many thanks.

Check in the BIOS if you can change it, considering the mobo you have I think you can't change it (I can't with my 850 MS-6545) and thus it will stay at 1/3.
A moderator at this forum told me it will automaticly change when the FSB reaches 133MHz, though. Pity, I'm not able to test that because my PSU can't supply enough power (probably not enough Amperes on the +12V line) to raise the Vcore to 1.7V. That's why my processor refuses to even POST at 120*20=2.4GHz. Because of that the PCI/AGP are running way to high (pci almost 40MHz) which caused my HD to corrupt some windows files and even lose a (empty) partition.
So, check whether you can change it manually, or try to make the big leap at once. Just be sure to up the Vcore enough, or you won't even POST

PSU recommendations for KT6 Delta

What are the recommendations for a PSU for the KT6 Delta? After reading some of the posts here, it sounds like the Fortron/Sparkle 350W I got is probably causing the problems I'm having. I would prefer something on the quieter side (hence the Fortron with the 12cm fan ). Also, I will eventually want to upgrade to an XP 3200+.
Thanks!

This is part of what Wonka answered to a P.S question: "antec enermax pc power and cooling 430 watts and up " Of course it all depends on what hardware you are going to use, but if you are planning an XP3200+ i can bet for a big one 450-500W
Now, the most important part you have to pay attention is the AMPS to 3.3v 5v. and 12v. They should be more than 30A. to 3.3 and 5v. and more than 25A to 12v.

Bios 5.4 for KT6 Delta causes instability!

Hi all,
I just wanted to warn those using the KT6 Delta to hold off on flashing there bios with the file the MSI German site has released. I awoke this morning to a booted up machine(wierd as I shut it down the night before)I thought no harm no foul, but lo and behold my machine had completely frozen wierd as it hasn't every done that never even had a crashes or BSODs I rebooted it was fine for most of the day until I was doing some surfing, and the machine froze once more. That's the not the end yet I rebooted, and this time it froze during the os load I switched it off kinda annoyed a 3 grand machine with quality parts shouldn't do this.
I turned on my laptop placed bios 5.2 on a floppy hooked up my usb floppy to my desktop, and proceded to flash bios 5.2 which did the trick hasn't faltered yet rock solid. While it's probably not an issue everyone might have I'd wait until the Taiwan site releases the bios update and then flash there must be a reason why we haven't seen the update on any of the other sites.

Much Appreciated for the info on the New bios
sorry that you had to go thought that trouble just to find that out!
I try to wait for new drivers etc, to come this website before I play with expensive hardware,
:evil:I would be pissed to see anything happen to my pc's just cause of some Beta driver?
Oh well, thats life Eh!
Thanks again for the heads up

MSI KT3 Ultra ARU PCI/AGP divider

Hey,
I'm using the overclocking features on the board, but i can't find the PCI/AGP adjustment in the BIOS, any body know what i can do??
I'm using the latest BIOS which is 5.6
Cheers

Ah, now thats what i've been told but according to Sisoft Sandra my AGP is 86Mhz and PCI is 43Mhz so itdon't look like its kicked in.
Any advice, do i have a dodgy board?

RAM for KT6 Delta-LSR

I'm currently running 2 x 512MB of DDR400 in my old KT6 Delta-LSR, and I want to upgrade to a total of either 2GB or 3GB.
Since this motherboard can only handle 2 slots of DDR400, I guess I'll be throwing out my existing ram, and starting from scratch.
I've just looked on the Kingston site, and they say that the KT6 Delta-LSR can only handle 1GB of DDR400.
So I can't simply buy 2 x 1GB sticks of DDR400? Is this right?
Quote
Maximum Memory: 1 GB using 400MHz DDR modules
http://tinyurl.com/yl74qbe
Should I just play it safe and get 2 x 1GB DDR333, leaving me the option of filling all 3 slots in the future?

If you're only running at 333ddr you may be able to run 3GB. But pc3200 will run at either 333 or 400, so you may as well get pc3200 and downclock it.
The board may not like 400ddr with all slots filled. I would get a matched 2x1GB kit, preferably low latency but not essential and just fill the outer slots. The kit may come in useful on an Nforce2, Nforce3 or similar higher performance platform although it's all getting a bit dated now.

AGP Setup For k7n2 delta ilsr

I have a k7n2 delta ilsr mb, in display properties on desk top setting tab then advanced button then GeForce tab under adapter information is Bus and memory. To the right of Bus it reads AGP (PCI mode) shouldn't that read AGP (8X), how can I change this. Ron.

Hi,
No, leave it at 64 or 128.
Go here for an explanation:
http://www.rojakpot.com/default.aspx?location=7&var1=18
Then - Click on: "Free Access To the BIOS Optimization Guide" near the bottom of the page - then click on "AGP Aperture Size"
Axel

[VIA] recommended memmory for kt6-delta

im looking forward in buying 2 sticks of 1gig DDR400 memory.
any recommendations is highly appreciated. thanks.

Thanks for the wonderful reply. I really appreaciate this forum and the people behind it.
To answer that question, my pc specs are.
-480w Thermaltake purepower to power up my cpu,2 cdrom drive, 1 floppy, 2x80 gig Harddisk, 1x512ddr, 9600xtATI.
-200w Oldskool PSU dedicated for my volcano 11 and 6 bigass internal fans.
-AMD XP2000.
would you think those abovementioned memory will work flawlessly on my system upon purchase?
Thanks in advance.

Best agp card for k7n2 delta ilsr

Hi again folks
I'm thinking of upgrading my graphics card as although this card has never let me down its the oldest component in my box, I would like to get something in the sub £100 range, I dont do games but may wish to in future, mainly it would be for photo apps/running-backup-watching dvd's etc. any info would be greatly appreciated tia Hazzo

I notice your talking in £'s so I assume your located in the UK.
Have a look around overclockers.co.uk
For a sub £100 I noticed a good offer:
HIS ATI Radeon 9800 Pro - £82
Also, the 6600GT here is only £103.24 (£106 inc delivery), altough only 4 left in stock so buy now if you want one

Via 4 in 1 Drivers and Bios for KT6 Delta

Below is my current setup. My machine either freezes or shuts down when I try to install the Via 4 in 1. Any suggestions?
Also, what Bios should I load? I've heard of problems with the most recent release.
What is everyone else using and what do you recommend?
Thanks in advance.

Are you sure you have installed the right VIA drivers (they're are different driver types for different system setups)? Sounds like you have put on the wrong VIA drivers.
The VIA drivers that you should use can be found on the MSI website:
http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=474
Always look under the driver section and you will find all the suitable and current driver updates for VIA chipsets for your motherboard.
Hope that helps, Richard.

KT6-Delta bios 5.7 problem

hi I've recently installed an update on the bios on my motherboard (update 5.7 for kt6-delta)
and ever since i installed it my internet won't connect, it detects the drivers but the internet can't send the pass username to mts.
is this a known bug? or was there just an error installing the update and should rewrite the bios possibly with an earlier update or is there some other problem i might not have considered because every time i install bios updates it resets my preferences in the bios

Hello,
Are you saying that the LAN appears to be working but no Data flows in or out?
All network activity is dead?
I have had this problem too on my KT6 delta.
When you flash the BIOS it changes the memory and CPU settings.
Also after a BIOS flash you should clear the CMOS using the Jbat jumper.
(turn PC off to do this)
If you enter the BIOS and disable the LAN,
DO your CPU and memory settings,
save and exit.
Go into windows, delete the lan from device manager
restart PC, it should be gone.
Then restart again, enter the BIOS enable the LAN, save and exit.
windows so detect it again, does it now work?

Cannot install LAN driver for my "KT6 Delta Series" motherboard

I've got this motherboard (KT6 Delta Series). Bought it second hand recently and I haven't got the original MSI driver CD. I downloaded all the drivers from the MSI website (http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=474&kind=1) but I'm not able to install the driver for my onboard LAN.
I just get a yellow dot on the ethernet controller under unknown devices in my device manager. When I try to update driver from device manager by searching the folder where I unzipped the driver, I just get a message saying something like "no driver could be found for this device in the selected folder... will you connect to Windows Update to search for a driver...?". I've also tried to install it the hard way by selecting "from floppy disc" and browse for the "b44win.inf" file inside the "WinXP" folder in the unzipped driver folder... but I stilll get an error message... saying something like "can't find any information of the hardware in the selected folder"... it's a bit difficult for me to describe the messages correctley because not English Windows version.
I've downloaded both LAN drivers for this card from MSI download site (http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=474&kind=1). Both "Broadcom 5788 LAN Drivers" and "Broadcom 4401 LAN Drivers" and non of them will install on my system. I've also tried downloading from the Broadcom website (http://www.broadcom.com/drivers/downloaddrivers.php). NON of them will install (
I've just formated my harddrive with fresh Windows XP install... The only software already installed is drivers for my motherboard and AGP card. No other software that can make any conflicts. When I connect a network cable to the onboard LAN the yellow light goes on so it seems the card itself is working.... but where can I get a driver that will install???
I've also tried connecting another network card (realtek 10/100) and connected my ADSL internett through it... and used the MSI Live Update utility... but still no luck... the only network driver it gets is the one for my reltek card :-(
Any suggestions???
I use Windows XP Professional SP2. How do I install the drivers for my onboard LAN???
Best regard.
Tor-Atle Kindsbekken

Quote from: osnavi on 05-November-05, 20:02:09
"...so my onboard Broadcom 4401/5788 controller thinks it is a 3COM controller instead of a broadcom controller..." Think it shouldn't be possible since basic data should be written in a kind of ROM. Now, if that could happen, it should be possible to reverse it the same way you did to overwrite that data.
I belive you are right... but I can't reverse it the same way I did when overwrite the data... because I'm not able to install the driver :( I cannot install the driver at all in Windows XP. In Windows ME it's possible to force the installation of the driver... but it does not work. It moves from unknown devices to network controllers... but it gets a yellow dot... and is not working. Every time I boot Windows ME I get a message reporting that something is wrong with the broadcom ethernet controller :(
I belive the only way I can reverse it is to replace my harddrive with another... with Windows XP and drivers for my card is already installed on the harddrive... the same way as I did when overwriting the rom file(s) with data from my Asus board... but I can't make such a harddrive when the drivers won't install on my card :(
I maybe think this also has happend to the onboard Audio controller... and maybe the chipsett also :( The audio controller works perfectley eith the MSI C-Media drivers... but when I run MSI live update... I get drivers for the C-Media device... but also drivers for "VIA AC97" audio controller can be downloaded from the MSI Live Update Utility... The "VIA AC97" is the audio controller on my Asus board... so I belive it has happened here also... and maybe also to the "VIA 4in1" chipset... but this is the same "VIA KT600" chipset as on my Asus board. When updating my Via 4in1 driver, I just get an option to update the inf file. But normaly on "Via 4in1" drivers on other boards I know, there shold be installed drivers for PCI, IDE and AGP. Is it the same way for you guys with this motherboard? Is it only the "Inf file" to update for you guys also?
What I think is most frustrating here is that things like this cab happen. This can happen to everybody. Many times I've switched harddrive from one computer to another... and I've never experienced anything like this before. This time I was not planing to boot the harddrive at all... just format it... but forgot to set the right boot order... so the harddrive booten... and that's all it takes to "destroy" my board. Shouldn't these ROM files be a littlebit more difficult to overwrite, you think? Why doesn't MSI writeprotect their ROM files or anything... to make them a littlebit more difficult to destroy...?
Well... I'm still interested in advices on how to "restore" my motherboard data to the original values... and remember... clear CMOS and update BIOS is not enough :(

KT880 DELTA & PCI/AGP Lock ?

I read some article about KT880 DELTA and there was written, it has PCI/AGP lock .. is it right ? If yes, which setting in BIOS is it ?
thx for any answer

I have heard this board will have that feature, but I cannot confirm it. If it does have the PCI/AGP lock, it would be the first VIA chipset to include this feature.
I would think it could be found in the "Frequency and Voltage" section of BIOS.

Video display driver for Trident Cyber9525DVD PCI/AGP (W98.23)

I am having problems finding a suitable (generic) driver for my video card. I'm installing Solaris 8 for Intel on an Acer Travelmate 330T laptop with a Trident Cyber9525DVD PCI/AGP (W98.23) display adapter. The installation was successful but it just couldn't get into the CDE. Could anybody help me? Thanks.

Hi:
See if this driver works. If it doesn't, you will need to install a 64 bit operating system if you want to run windows 7.
I know this driver works for the Celeron N processors, but I don't know if it will work with the Pentium N processors.
Download, unzip and run the setup.exe file.
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23889

[VIA] Problem with Creative X-FI on KT6 Delta FI2SR

Hi all
I have a KT6 Delta FI2SR with 1GB PC3200 400MHz DDR, and an Athlon 3200XP+, running BIOS 5.7 (latest).
I recently bought and added a Creative X-Fi Fatal1ty FPS soundcard, and I have an issue....
The card was installed, is on IRQ19 (no conflicts anywhere with sound), and on-board sound is disabled.
Randomly, on cold boot, I get told "NVRAM Update OK", and then I get NO SOUND!
It stays like that until I reboot and it "Updates" again, or I clear the NVRAM in BIOS.
LOTS of people on the Creative Forum have reported similar issues with ASUS Mobos, and nForce chipsets, but this is an MSI with VIA!
ALL (and I do mean ALL) device drivers are up to date....
Can someone @ MSI look into this? ASUS have resolved their issue with BIOS updates, but nothing for this board for a while!
I've tried mailing MSI support BUT [email protected] AND [email protected] get SMTP failures (no known username).

I would hope the PSU is fine - it's a 620 watt PSU which I bought when I installed a GeForce 6800GT
Both motherboard power connectors are connected up. PSU has two outgoing rails, with 3 main Molex and 1 mini (floppy) adaptor on each rail.
In the machine we have :
1 x Asus V9999GT GeForce 6800GT AGP 8x card (with dual molex connectors)
1 x Creative X-FI Fatal1ty FPS PCI card
1 x Adaptec 29040UW SCSI controller PCI card
2 x 80GB Maxtor 7200RPM SATA HDD drives (as one RAID0 array)
1 x Creative Fatal1ty FPS front bay (powered - small connector)
1 x MSI Dual-Layer DVD+RW Drive
1 x HP Surestore 12/24 DDS3 DAT Drive
1 x Panasonic LS-120 HDD Floppy Drive
1 x IOMega ZIP 250 ATAPI Drive
Logitech cordless keyboard & mouse on PS2 connectors
COM1 has a trackball
COM2 is a signal cable for a Liebert Powersure UPS
LPT1 is disabled (I have a networked printer)
7 of 8 USB slots are currently in use : (Joystick, Bluetooth adaptor, Fuji 6900Z Camera, Primefilm 35mm film scanner (own power), HP Jornada 568 PDA (own power), Logitech QuickCam Home webcam, Wacom Graphire Tablet)
CPU fan is powered and adjustable, and the case has 7 controllable fans.
There is a SCSI scanner (own power) and the 17" LCD monitor connected (on it's own power) as well, and thats it.
I've disabled the Case LED (which was also powered).
Obviously there are a couple of power splitters in there to supply power to the various internals

PCI/AGP divider for KT6 Delta

Similar Messages

Maybe you are looking for