Pci controller error

Hye guys really need assistance!!!
My laptop cannot boot up to windows, always shows pci controller error and auto restart..
Any idea??
This question was solved.
View Solution.

Have you checked with win 7 OS alternatively please provide the exact error code.
I'm an HP Employee.
The opinions expressed here are my personal opinions, not of HP.
Make it easier for other people to find solutions, by marking an answer “Accept as Solution” if it solves your problem.

Similar Messages

HD Controller Error in System Properties

Hello,
Under system properties--hard disk controllers I have 3 entries: Primary IDE Controller (single fifo), Secondary IDE controller (single fifo), and Duel PCI IDE Controller.
The primary and secondary IDE controller entries have exclamation marks next to them noting that they are not working corectly.
My 2 hard disk drives do not show under the disk drive entry due to the controller "errors".
What IDE drivers should I use to fix this problem. Since I cannot access the hard drives I cannot turn on DMA support.
Thanks for the help!

Quote
Originally posted by biodude
What IDE drivers should I use? The drivers that the puter wants to use (MS) aren't good. I can't see my hard drives, or CD ROM in Win ME system properties. This means that the drives are using MSDOS compatibility mode.
Does NVIDIA have any NF2 IDE drivers?
Thanks
Can your machine read CDs? There may be drivers for your IDE controllers under Windows ME on the CD that came with your motherboard.
Caveat: I am speaking from experience with EPoX and ASUS motherboards; I am fairly new to MSIs, but I would expect they would have the same sort of drivers available.
--Barry

Portege M750 - PCI controller software not installed on Windows 7 64bit

Hi, had an upgraded SSD for my machine so decided to do a fresh install of Windows 7 64bit and now I have and error saying PCI controller software is not installed, tried windows update no luck - any ideas please?
Thanks, Peter

OK cool advice - thanks it is from Intel and is
0x2A44 Chip Number: Mobile 4 Series Chipset
Chip Description: Intel Management Engine Interface
Notes: ftp://ftp.vaio-link.com/PUB/VAIO/ORIGINAL/ME DRIVER INTEL 4.0A _ 4.0.0.1105.ZIP
Downloaded, installed and working - thanks for the quick advice!
Peter

An error was detected on device \Device\Harddisk3\DR3 during a paging operation. - The driver detected a controller error on \Device\Harddisk3\DR7

How can i ensure that the harddisk3 designation is relatd with USB etxernal disk?
I have several erros in LOGs:
An error was detected on device \Device\Harddisk3\DR3 during a paging operation.
and
The driver detected a controller error on \Device\Harddisk3\DR7
All times are HardDisk3 and sometimes it references to DR3 and sometimes DR7
My disk structure is:
2 RAID5 arrays fomr the same disks (80GB and 2 TB)
and USB 2 TB External hard disk with several partitions
I´m 99% sure that the error is related to the external USB disk and the Dell DIag tool shows no problems with any component
DISKPART> list disk
Disk ### Status         Size     Free     Dyn Gpt
Disk 0    Online           80 GB      0 B
Disk 1    Online         2711 GB      0 B        *
Disk 2    Online         1862 GB 1024 KB
DISKPART> sele disk 0
Disk 0 is now the selected disk.
DISKPART> detail disk
DELL PERC H700 SCSI Disk Device
Disk ID: 6EFE3928
Type   : RAID
Status : Online
Path   : 1
Target : 0
LUN ID : 0
Location Path : PCIROOT(0)#PCI(0400)#PCI(0000)#RAID(P01T00L00)
Current Read-only State : No
Read-only : No
Boot Disk : Yes
Pagefile Disk : Yes
Hibernation File Disk : No
Crashdump Disk : Yes
Clustered Disk : No
Volume ### Ltr Label        Fs     Type        Size     Status     Info
Volume 3         System Rese NTFS   Partition    100 MB Healthy    System
Volume 4     C   DISCO        NTFS   Partition     79 GB Healthy    Boot
DISKPART> sele disk 1
Disk 1 is now the selected disk.
DISKPART> detail disk
DELL PERC H700 SCSI Disk Device
Disk ID: {A42559A8-43EF-4570-B4CF-336A22A718BF}
Type   : RAID
Status : Online
Path   : 1
Target : 1
LUN ID : 0
Location Path : PCIROOT(0)#PCI(0400)#PCI(0000)#RAID(P01T01L00)
Current Read-only State : No
Read-only : No
Boot Disk : No
Pagefile Disk : No
Hibernation File Disk : No
Crashdump Disk : No
Clustered Disk : No
Volume ### Ltr Label        Fs     Type        Size     Status     Info
Volume 5         DADOS        NTFS   Partition   2711 GB Healthy
    C:\DADOS\
DISKPART> sele disk 2
Disk 2 is now the selected disk.
DISKPART> detail disk
HP External HDD USB Device
Disk ID: 000904F0
Type   : USB
Status : Online
Path   : 0
Target : 0
LUN ID : 0
Location Path : UNAVAILABLE
Current Read-only State : No
Read-only : No
Boot Disk : No
Pagefile Disk : No
Hibernation File Disk : No
Crashdump Disk : No
Clustered Disk : No
Volume ### Ltr Label        Fs     Type        Size     Status     Info
Volume 6         SOFTWARE     NTFS   Partition    300 GB Healthy
    C:\DADOS\DISCO-EXTRA\
Volume 7         TEMPORARIO- NTFS   Partition    148 GB Healthy
    C:\DADOS\NEW_TRANSF\TEMPORARIO\
Volume 8         TRANSF_LIXO NTFS   Partition    149 GB Healthy
    C:\DADOS\NEW_TRANSF\TRANSF_LIXO\
Volume 9     R   RESTORE      NTFS   Partition   1264 GB Healthy

Hi,
For finding the exact hard disk you could refer to this article. It is an old article but the structure is not changed:
How to Distinguish a Physical Disk Device from an Event Message
http://support.microsoft.com/kb/159865
Meanwhile for the error message "error was detected on device \Device\Harddisk3\DR3 during a paging operation", according to my search result it could be related to fragments. So please try a defragment on your hard disk (if it is the USB disk then perform
a defragment on USB disk) and see the result.
If you have any feedback on our support, please send to [email protected]

Tecra M9 - PCI Express Error at start-up

Hello Everybody ..
I own a Toshiba Tecra M9 (PTM91E-04R03TEN)
http://www.toshiba.ie/innovation/jsp/supportMyProduct.do?service=IE#tab0;
On switching on,- Its Showing the Toshiba splach screen and then "PCI Express error." on a black screen
I can't get beyond this Black Screen
and I can't get into BIOS ??..
One time it did manage to boot up fully, I left it running for a while as I save information from the HDD. but then the problem started again .
I believe this is a problem with the nvidia GPU ( Fatigue cracking on the BGA )
I have the Laptop stripted down .. and have purchased ArctiClean , Thermal Pad, & Arctic Silver for the "repair"
Should I have somebody scan the hardware and to find the troublemaker ? ..OR.. should I just reflow the GPU .
I'm technically minded .. but not a PC / Laptop technican :(..
any Instruction on how to proceed would be greatfully received ..
Should i just " bung it in the oven" and see how it goes ? :) :) .
Regards,
Peter

Hi
I found and read your other post regarding this issue and in my opinion the PCI Express error is related to an PCI device (i.e miniPCI module like WLan / Bluetooth, etc ) connected to the motherboard.
Of course I cannot say for sure that this issue isnt related to a GPU malfunction.
Usually such details can be provided only by an service engineer who checked the notebooks hardware.
Generally I dont recommend to disassemble the notebook. Its very tricky to perform such procedure and of course there is always a risk of part damage doing such procedure without any instructions.

Windows 7 - Pci-to-Pci Bridge (Error: Code 10) - PCI Video Card

Before I state my issues I will list what I'm running and what I'm trying to accomplish.
I'm running Windows 7 Enterprise 64-bit edition, not the Beta or RC. I have 3 video cards in my possession (listed below).
- (PCIe) Evga GTX260
- (PCI) Evga 9400GT
- (PCI) Evga Fx5500
Out of those 3 cards I only use the GTX260 and the 9400GT. I had to 'retire' the Fx5500 because the latest WHQL (certified) drivers only provide support as far down as the "6 series" Nvidia cards. Unfortunately the Fx5500 is a "5 series" and falls below that line. I have already tried to use the GTX260 and Fx5500 in previous versions of Windows (XP and Vista), but there is no way to download and install two separate drivers for two of the same make of video card - you'll get nothing but errors. There is the option of going to a place like guru3d.com and downloading a custom supported driver that covers both the GTX260 and Fx5500, but the drivers are not certified and lack support. Therefore, I purchased and now use the 9400GT which is covered under the drivers for the GTX260 and eliminates the need for messing around with custom drivers. Also, the 9400GT has a better graphics processor and more memory than the Fx5500, so it was time to upgrade anyway.
Now that you have some background info here is my issue Whenever I install the 9400GT I get a second 'pci-to-pci bridge' entry (the other entry has no errors) that shows up under 'System Devices' in the Device Manager. The second pci-to-pci bridge entry has a yellow triangle with an exclamation mark on it that refers to a problem. When you check the properties of this device it more or less says that Windows has detected a problem (Error Code 10). The GTX260 still works and even shows up under the 'Display Adapters' as a GTX260, but no entry for the 9400GT exists. I have tried the 9400GT in both PCI slots and each time it does the same thing. If I pull out the GTX260 and ONLY run the 9400GT, I still get the pci-to-pci bridge issue, BUT I do get a picture and can boot into Windows 7 without a hitch. When I do this there is still nothing listed under the 'Display Adapters' as a 9400GT or even a VGA compatible device.
After messing around with this for 10 hours (yes, I said 10 hours) I decided to dig out my retired PCI video card (the Fx5500). When I installed this card I had no 2nd pci-to-pci bridge entry appear under 'System Devices', and the one that was listed had no yellow triangle or error codes. I then checked under 'Display Adapters' and Windows 7 had recognized it as a VGA compatible device and was asking for drivers.
I have now concluded that there is definitely no issue with the motherboard or any of my hardware (including video cards). At first EVGA Support and I had suspected that the motherboard may be bad because of all of the pre-diagnostic steps I had taken during my 10 hour ordeal. I'm not going to list everything I did because it would literally take 3 hours to type it all in. Just believe me when I say that I have tried most things including but not limited to the latest bios updates (flashed 4 times and completely reset to ensure accuracy), custom IRQ management, entire OS re-installation X2, multiple/latest chipset drivers installed, multiple/latest video drivers installed, memtest testing, complete hardware teardown and re-build (adding one device at a time), and MUCH more. The only thing I did not try was installing a different OS other than Windows 7 64-bit to see if I could replicate the issue. This is a waste of time though because lets say that I install Windows XP Pro and the 9400GT doesn't have this issue... Well, that's great, but who gives a damn about XP Pro when I have been using it for the last 9 years and when I have a full version of Windows 7 that I want to use? I'm certainly not going to run XP Pro over Windows 7 just to use this PCI video card. Second, if I install XP Pro and it still gives me the same pci-to-pci bridge error then again, I've only wasted more time because if its not going to work in either OS then Im sure as hell not going to leave XP Pro installed when I can use Windows 7.
Thanks,
piyush

Maybe stupid question now but has your posting anything to do with Toshiba and Toshiba notebooks?

Solaris 10 on Sun Ultra 40 --PCI system error on /bus/device/function 0048h

Everytime I boot to Solaris 10 (08/07) I get the following message at the top of my screen:
PCI system error on /bus/device/function 0048h
The system boots up successfully, but I find this error to be particularly annoying. I have no third-party cards plugged into any PCI slot.
Why am I getting this error. Is the BIOS just giving me a bogus error?
Any help would be appreciated.
Thanks.
Robert

Hello,
I even got the same Problem with an Ultra 40. After powering off and on the system during the last 3 days, now i got an error mesage, "CPU3 can not be started"
cleared the CMOS and now i am back on "PCI System Error on Bus/Device/Function 0048h" the system is running with the latest 1.7 Bios update.
First of all I tried to flash the system back to an lower version but the flashsoftware seems not to support this operation have to make own boot media with the flashprogramme and flash by forced the 1.0 or 1.2 version.
regards
Monchichi

QT Pro Crashes with "Export Controller" error when converting M2V to H.264

I am currently experiencing a problem with QT Pro for Win. Any time I try to convert a M2V file to an H.264 encoded .mp4 file, QT pro gets approx 10-16% complete with the conversion and then crashes. (This happens when trying to encode an 2hr SD M2V file taken from a DVD or a 1/2hr M2V HD file recorded via EyeTV, so the resolution/size isn’t an issue.) The error message is always that there was a “QT Export Controller error”. I do not get this kind of error when using the same files with QT Pro on my MacBook only on my windows box. I am running the most current version of QT. Does anyone have any ideas on this?

Hi,
I too am having crashing issues.... and I too got no help from Apple. Just go to website they said... great!!?? Now I know why I never use these guys products!!!
However, rant over, I do have a need to use Quicktime.
I am trying to use Quicktime to convert quicktime movies to the new H.264 codec, a function available with Quicktime Pro.
However when I go to export window and then to the video setings window, quicktime just suddenly closes(not crash). I can go into the audio section though and change options in there. I have uninstalled and re-installed with no luck.
This is extremely frustrating
any help greatly appreciated
sharky

I get MP AV controller error domain error 3 when I try to play a movie I rented. Using OS 8.1.3

I Updated my OS a few days ago and downloaded 3 movies. When I go to play the, I get the error message
MP AV controller error domain error 3
wwhat is this and how do I access the movies I have paid for?
thanks!

this worked for me: after downloading a movie from itunes i get the message MPAV Controller Error Domaine error 3 what can i do ?
Basically
log out of itunes from settings
power off the ipad
power on the ipad
log back into iTunes
then the video was available

Getting Export Controller Error When Exporting MPEG2 to High boardband & up

I just got QuickTime Pro and MPEG 2 Playback for Windows. I am getting an Export Controller Error When Exporting MPEG2 to High boardband or to the default settings. The file I am exporting is around 60 MB and when it gets to about 15%, the program errors. However, the program works for Medium and low Board band. If anybody has a solution for my problem, I would love to know.
Thanks!

Not sure if this is going to work, but it worked for me. After exporting the movie and I got the error, I noticed that the process "exportController" was still running, so I stopped it from the task manager and am not sure but apperantly that was the problem because once I did that the file open up fine in other players like Winamp. Also after stopping the process the following exports I did seemed to be exported fine without any errors !... worth a shot.

HT202027 Mpav controller error doman error 3 on a movie download that never completed download

I Was downloading a rental and my wifi was interrupted and I never was able to finish my down load. I have now been charged the 5.99 and not able to watch to watch the movie. I keep getting the error MPAV controller error domain error 3. Any idea how I can get the download to recommence?

Greetings Deedledash,
Welcome to the Apple Support Communities!
I understand that you rented a movie from iTunes and the download was interrupted before it finished. For this situation, I would recommend using the attached article for information on resuming your download.
iTunes: How to resume interrupted iTunes Store downloads - Apple Support
Cheers,
Joe

After downloading a movie from itunes i get the message MPAV Controller Error Domaine error 3 what can i do ?

after downloading a movie from itunes i get the message MPAV Controller Error Domaine error 3 what can i do ?

Log out of iTunes from Settings, power down and restart the iPad, log back into iTunes. Your download should play now.

Pci device error

After re-installing xp with sp2 im getting pci device error in the ctrl panel and cannot get any sound from my pavilion2020ca. I,ve tried all the drivers in hp site to no avail. Any help would be grateful.

Do you have ZE or DV 2020ca? If you have DV2020 have you installed Microsoft UAA driver?
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

PCI Express Error - Qosmio G40-10Z

Yesterday i turned on my laptop and i got a black screen with the message "PCI Express Error"
I immediately started searching the web what this error might be and i discovered that it's a known problem with some Toshiba laptops.
http://www.nvidiadefect.com/qosmio-pci-express-error-t383.html
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=49108
http://www.nvidiadefect.com/toshiba-qosmio-g40-12c-t1149.html
Just a few of the many topics i found about this error.
I bought my laptop January 2009 as a demo model from a dutch store called Qplaza http://www.qplaza.nl/
Don't think i have any warranty beside the warranty i got from that store (2 years) but there are a few things i don't understand.
From what i understand is that there even was a lawsuite about this problem and that there indeed was a problem with the nvidia 8600 chips. But then why won't Toshiba or Nvidia fix the laptops with those problems?
From what i have read my laptop would have to go to special repair service to replace my motherboard and i will have to pay for that myself.
And that is IF they can fix my laptop.
I started searching the internet what the price costs might be but the answers didn't make me a very happy woman :-(
Isn't there another way to fix this problem?
And aren't there places where you can buy a suitable motherboard for this laptop?
Can anybody please help me?? My laptop was working perfectly and without any warning..poof...can't get it to work anymore.

Dear Debzel,
As the proud owner of an attractive piece of scrap with G40 stamped underneath, due to what is almost certainly the same fault as you have, I have been through the customer service route and found that they are not going to officially recognise that the n-vid fault exists on our laptops and will only offer you a repair at your cost.
Due to the conspicuous lack of messages on this forum regarding this inherent fault, I suspect that this message may be quickly removed from the site. Having taken advice from the chap who runs the n-vid defect website, I realise that the only way forward is to take on Tosh legally. The consumer has strong rights in the UK as I suspect is parallel in Holland (assuming that's where you're based). I would be willing to send you my letters, based on templates from the defect website and Consumer Direct (phone them if you're i the UK and get it from the horse's mouth that your product should have lasted longer than it did - 08454 04 05 06), but with some information about my personal situation added.
You also have to send a copy to the credit card company that you used when making the purchase, if that was the case, as this puts you in a stronger position. If you didn't use a CC then that's a shame but not the end of the road, you can still take them on and by all reports, you should be successful as the PC is very young for the price you would have paid. The other repondent to your post must work for Tosh, which is why they were so unhelpful.
Kind regards,
steve oram at bt inter net dot com.

The driver detected a controller error on \Device\Harddisk1\D

Hope someone can help, yesterday in the event viewer I encountered the following error
"The driver detected a controller error on \Device\Harddisk1\D
....I have added no new hardware for months, I checked this out on the microsoft website but they recommend changing the cable!
I ran diagnostics on the hard drives and they found no errors at all ....I got a feeling it the motherboard, frustrating as this is the second board Ive had!
Can anyone advise on this error?
My setup is as follows
P4 3.2GHZ
1GB Transcend Memory
1 NEC 2510 DVD Wrtier
1 IDE 120GB Maxtor Diamond Max
2 X SATA HDD
450 watt Thermaltake Butterfly PSU

This seems to be a common problem between ICH5 chipsets and SATA NCQ drives. Apparantly a BIOS update will be able to fixed the problem but I'm not sure which BIOS you should use. I suggest that you check MSI's website to look into your mobo's BIOS release notes to find out more first.
Please also note that there's an amount of risk to flashing your mobo's BIOS as and improper flash will caused the mobo to die immediately or having multiple errors due to bad flash. I would recommend that you flash through a floppy bootdisk which seems to be the best method till date.

Pci controller error

Similar Messages

Maybe you are looking for