Pci device doesn't work till reboot

Hello, I'm new to these boards so please forgive any errors in posting.
i use my computer as a pvr. The problem is if i shutdown my computer for more then a minute the pci slot hvr-1600 stops working. If i reboot it comes right back up working again. Tried the card in another computer no problems worked fine. Besides this issue computer is completely stable not one bsod or lockup...so far heheh
Intel Core i7-2600K Sandy Bridge 3.4GHz
MSI P67A-GD65 (B3) Bios 1.8
hec Zephyr MX-750 750W
Win 7 64 SP1
1 X Kingston HyperX 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Model KHX1600C9D3K2/8GX
1 X ASUS ENGTX560 TI DCII/2DI/1GD5 GeForce GTX 560 Ti (Fermi) 1GB 256-bit GDDR5 PCI Express 2.0 x16
1 x SAMSUNG Spinpoint F1 HD103UJ 1TB 7200 RPM SATA 3.0Gb OS
1 x HITACHI Deskstar 7K1000 HDS721010KLA330 (0A35155) 1TB 7200 RPM SATA 3.0Gb Storage
1 x Hauppauge WinTV-HVR-1600 ATSC/ClearQAM/NTSC TV Tuner MC-Kit 1183 PCI
1 x LITE-ON Blu-ray Burner with 3D Playback SATA iHBS212
No over-clocking has been done, stock cooler for now

Quote
The problem is if i shutdown my computer for more then a minute the pci slot hvr-1600 stops working.
I don't quite get that. When you say you shutdown your computer, do you mean you are switching your computer off?

Similar Messages

[SOLVED] network randomly doesn't work after reboot (e100)

Hi
Lately I have some weird issues with network. I shutdown computer during night, so basicly I reboot it at least once per day and every now and then without any pattern network doesn't work at all and so far only solution I have found is to reboot (again).
Before anything else I'm sure it's not hardware problem, since other OS on same computer don't have any issues, neither is router since other devices in network from laptops to mobile phones work flawless.
Relevant info and what I have found so far (not everything is copy/pasted so there may be some typos):
$less rc.conf (network part)
eth1="eth1 192.168.1.242 netmask 255.255.255.0 broadcast 192.168.1.255
INTERFACES=(eth1)
gateway="default gw 192.168.1.1"
ROUTES=(gateway)
$ifconfig
eth1 Link encap:Ethernet HWaddr 00:D0:B7:5A:7A:A9
inet addr:192.168.1.242 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:380 errors:0 dropped:0 overruns:0 frame:0
TX packets:380 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:36154 (35.3 Kb) TX bytes:36154 (35.3 Kb)
$route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 * 255.255.255.0 U 0 0 0 eth1
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth1
$ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data
From 192.168.1.242 icmp_seq=2 Destination Host Unreachable
So basicly network is dead, can't even ping router, cable connection is detected tho (lights are on). I have tried to restart newtork with /etc/rc.d/network stop/start, nothing. Only clue is dmesg.
$dmesg
Linux version 2.6.30-ARCH (root@T-POWA-LX) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Fri Jul 31 07:30:28 CEST 2009
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:03:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
e100 0000:03:07.0: PME# disabled
e100: eth1: e100_probe: addr 0xfdfff000, irq 17, MAC addr 00:d0:b7:5a:7a:a9
e100 0000:03:07.0: firmware: requesting e100/d101m_ucode.bin
ADDRCONF(NETDEV_UP): eth1: link is not ready
modrope -r e100 and then reloading it doesn't help either, but reboot does (once I had to reboot twice tho).
Anyone with more clue and ideas then me, it's getting really annoying, it also kill whole KDE plasma-desktop for couple of minutes before plasmoids find out network is really down and I'm not really fan of morning "gamble". I can't pinpoint some hard date/update when this started to happening because like I said it's random but last couple of months should be quite accurate. Thanks in advance.
EDIT: dmesg when network works:
tilen@pikmin ~]$ dmesg | grep e100
pci 0000:03:07.0: Firmware left e100 interrupts enabled; disabling
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:03:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
e100 0000:03:07.0: PME# disabled
e100: eth0: e100_probe: addr 0xfdfff000, irq 17, MAC addr 00:d0:b7:5a:7a:a9
Last edited by NoOrdinary (2009-09-05 09:47:20)

I don't have anything special set at router but I doubt rc.conf play any role. I will try to set it up with dhcp (but I think I have tried that already) if there is any change.
This morning I had to reboot twice, so new kernel didn't help. Fowler, what network card are you using, also e100 (well or some intel)? I dunno, should this be handed to the kernel team? If it will piss me enough one morning I'll just go and buy a new network card, just wanna be sure that will really solve the problem.
UPDATE: OK, this is just silly. I remebered I have acctualy onboard LAN so I edited rc.conf and dived into the dust under my desk to move cable and there I found out it was acctual onboard in use all the time Now this dosen't make much sense to me anymore, when I can't get net up all the stuff in dmesg is e100 related. Anyway, I connected network to e100 and rebooted, suprise, same story. Dmesg reported again link was not ready. I edited rc.conf to
INTERFACES=(eth0 !eth1)
in case this has anything to do with proper timing at assigning whatever needs to be assigned to network cards at boot so I'm sure just 1 card with all info provided get's kicked in at boot. First reboot after that works, it dosen't prove anything yet but at leat it's some kind of progress in recognising proper cause.
UPDATE 2: Nah, still happens. Googling for "no link during initialization" show a lot of familiar problems, almost all on nforce motherboards and mine is nforce too. I just don't get it why this mess seperate PCI network card. In any case it's extremely annoying.
Last edited by NoOrdinary (2009-09-02 11:46:27)

[SOLVED] Default audio device no longer works after reboot

After today's reboot, the audio device no longer works. E.g., VLC says:
Audio output failed:
The audio device "default" could not be used:
No such file or directory.
This is the console log:
[0x1394138] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface.
Fontconfig warning: "/etc/fonts/conf.d/50-user.conf", line 9: reading configurations from ~/.fonts.conf is deprecated.
[0x7fac180069c8] pulse audio output error: PulseAudio server connection failure: Connection refused
ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave
[0x7fac180069c8] alsa audio output error: cannot open ALSA device "default": No such file or directory
[0x7fac180069c8] jack audio output error: failed to connect to JACK server
[0x7fac180069c8] oss audio output error: cannot open audio device (/dev/dsp)
[0x7fac180069c8] main audio output error: no suitable audio output module
[0x7fac40fa4db8] main decoder error: failed to create audio output
[0x7fac180069c8] pulse audio output error: PulseAudio server connection failure: Connection refused
ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave
[0x7fac180069c8] alsa audio output error: cannot open ALSA device "default": No such file or directory
[0x7fac180069c8] jack audio output error: failed to connect to JACK server
[0x7fac180069c8] oss audio output error: cannot open audio device (/dev/dsp)
[0x7fac180069c8] main audio output error: no suitable audio output module
[0x7fac41055118] main decoder error: failed to create audio output
The strange thing is that the sound card does in fact work; e.g. the sound test for "HDA Intel PCH", the first entry in my KDE Audio Settings, works. But the entry "default" does not and I suppose that is also the device that VLC is complaining about.
I've tried blacklisting the HDMI driver and switched to the other audio output modules in VLC. I've also checked I'm still member of the "audio" group.
Edit:
P.S. Solved this myself. I had a USB-to-MIDI adapter cable plugged in during boot, which seems to have been causing these problems. I suppose systemd thought it was a USB sound card? I was wondering why dmesg said something about USB sound when the computer doesn't have any USB sound devices. Hardware detection epic fail. Although I guess the cable counts as a MIDI device at least, so in a way it's correct.
So it looks like I'll always have to unplug the MIDI cable before rebooting.
Last edited by Morn (2012-11-23 19:24:00)

You might get. Ore assistance in a different forum area. Maybe try Using pad. This is the forum for iPhoto for iOS.

My iPhone died and wont turn back on. My home button doesn't work to reboot it.

It died last night and I put it on the charger and nothing happens not even the battery symbol comes up. I do have the iOS 7. I can't restart it because my home button doesn't work and i have to use assistive touch. It won't show up on itunes when i tried to plug it in. It's not the charger because it works on my other i-devices. I have an iphone 4.

If the screen and iPod does not show any life then letting the batter drain will not do anything.
If you tried another cable and tried ReBoot on another computer and still problem then your iPod has to be repaired/replaced
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

[SOLVED]mounting cdrom and usb devices doesn't work

Hello,
i have trouble mounting my usb devices. automount doesn't work and i can't mount them manually even as a superuser. here's the output of mount command:
mount: wrong fs type, bad option, bad superblock on /dev/sdc,
missing codepage or helper program, or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
i can mount cdrom manually but i can't do the same for my usb stick and external hard drives. it always complains about the above regardless of the filesystem. my devices are working under windows and other linuxes so i know hardware is not the problem.
i'm using lxde with pcmanfm.
if you need any other files just ask.
thanks
Last edited by the gray (2009-03-16 20:15:18)

above was the error when i tried to mount any usb device with "mount -t <type> /dev/sdc /media/mountpoint". and i couldn't mount any usb device as root from console. when i tried to mount devices using pcmanfm it just popped some empty dialogs and i couldn't find any mention of "IsCallerPriviliged failed" error so i (wrongly) presumed it wasn't that. i did try some of the other fixes mentioned in the forum with no success. but adding exec ck-launch-session startkde to my .xinitrc fixed the issue
thanks again
Last edited by the gray (2009-03-16 20:17:53)

HT4664 compressor doesn t work till maverick is install

till i install marverick, compressor doesn t work, what should i do, i can t open it to install update... it say to old version... it does t appear on the app strode cause it was furnish with tha IMac

I'm afraid you will need to contact Apple to get this straightened out.
Russ

PCI SCSI Doesn't work with GF4 4400

I swapped my old Herc GF2 out for the new MSI GF4 TI4400 card and found out that my PCI SCSI card doesn't work with it in. Swapped back in the GF2 and it works fine, and also works in a diff PC.
Flashed BIOS of my Abit KG7-RAID, no change...
?!

someone suggested this may have to do with a BIOS limitation about how much ROM space can be used for initialization routines such as video BIOS, mobo BIOS, and any other I/O cards such as the SCSI... Apparently most SCSI cards use 64K or so of memory at init and shrink back to like 16K or so....
Going to play with moving the cards around to change the order of initialization and we'll see if any change occurs...

Auto-mounting USB storage devices doesn't work

Hi all,
I have some problems with the auto-mounting of USB storage devices. I already installed udisks and ntfs-3g.
When I connect the external device (it's an external hard disk WD My Passport 500GB, but I have the same problem with a SanDisk USB stick 8GB) the auto-mount doesn't work. I see a shorcut in the left panel of Thunar but if I try to use it Thunar crash without any message error.
I try with the manual mount and it works, but the left panel of Thunar continue to have the same problem.
In the italian Arch forum a friend suggest me to open Thunar from bash and close it. If I do it I receive this error log:
$ thunar
thunar: symbol lookup error: /usr/lib/libstdc++.so.6: undefined symbol: _ZNSt14error_categoryD2Ev, version GLIBCXX_3.4.15
and this is the reply of dmesg command:
[ 340.826768] usb 1-1: new high speed USB device number 2 using ehci_hcd
[ 341.591397] Initializing USB Mass Storage driver...
[ 341.592166] scsi6 : usb-storage 1-1:1.0
[ 341.592345] usbcore: registered new interface driver usb-storage
[ 341.592349] USB Mass Storage support registered.
[ 341.599805] usbcore: registered new interface driver uas
[ 342.591094] scsi 6:0:0:0: Direct-Access WD My Passport 070A 1032 PQ: 0 ANSI: 4
[ 342.591474] sd 6:0:0:0: Attached scsi generic sg1 type 0
[ 342.592845] scsi 6:0:0:1: CD-ROM WD Virtual CD 070A 1032 PQ: 0 ANSI: 4
[ 342.593048] scsi 6:0:0:1: Attached scsi generic sg2 type 5
[ 342.594050] sd 6:0:0:0: [sdb] 975400960 512-byte logical blocks: (499 GB/465 GiB)
[ 342.594814] scsi 6:0:0:2: Enclosure WD SES Device 1032 PQ: 0 ANSI: 4
[ 342.595141] scsi 6:0:0:2: Attached scsi generic sg3 type 13
[ 342.596546] sd 6:0:0:0: [sdb] Write Protect is off
[ 342.596553] sd 6:0:0:0: [sdb] Mode Sense: 23 00 10 00
[ 342.596557] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 342.599163] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 342.618228] sdb: sdb1
[ 342.621039] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 342.621046] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 342.665174] sr0: scsi3-mmc drive: 51x/51x caddy
[ 342.665180] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 342.665447] sr 6:0:0:1: Attached scsi CD-ROM sr0
[ 342.665654] ses 6:0:0:2: Attached Enclosure device
[ 349.105348] [b]Thunar[996]: segfault at 0 ip b6de1660 sp bfe586f4 error 4 in libglib-2.0.so.0.2800.8[b6d6f000+ed000][/b]
Do you have any suggestion?
Thank you very much,
Gianluca

Are you using [testing]? Partially updated system?
The error looks like you have a different version of gcc-libs / glibc than the app was built against.
Last edited by Mr.Elendig (2011-06-20 19:16:33)

[SOLVED]Keyboard and touchpad doesn't work after reboot from Arch

Excuse me, but i'm a newbie. I'm not sure if this is an arch problem, but i will just post it here.
I've beening using Arch64 and it works just fine. However, every time i reboot from arch into Windows 7 (32bit), the keyboard and touchpad will stop responding just when the Win7 splash screen shows, however the mouse works fine. Then when you shutdown the computer (from win7 now) it will take apparently longer time, and sometimes i have to press the power key 5 seconds to make it shutdown.
It seems the correct way (to reboot from arch to win7) is to shutdown down the computer first and start it again, and everything will work fine.
And rebooting from win7 to win7 or arch to arch or win7 to arch will work fine too.
I'm glad to post extra information, but I've got no clue and i'm not sure what to put here.
The laptop is a Lenovo Y450 with Intel Core Dual P7540, 4G Memory, NV GT240M. Kernel version of Arch is 3.0.6 (but the problem existed long since earlier versions) I don't have a swap partition. If you need extra information, please mention the item.
Thanks a lot!
Last edited by crlf0710 (2011-11-15 10:29:38)

Hi!
That is indeed strange. Since your external mouse works fine (which probably is connected via USB, right?) it appears that the problem lies somewhere around the internal keyboard/touchpad access. I'm not sure how this works with a Lenovo Y450, but just try to enter BIOS (in case you have not been there, you probably have to hit F1 or F2 during startup - less likely it would be delete or escape ...) and look for your keyboard/touchpad options.
You should probably find something like "... legacy support ...". This is a relic from PS/2 times and emulates your internal input devices as PS/2 devices. So - when found, just change the setting (you cannot mess anything up, and both systems will probably not even pop up a message). My guess is it is set to "enabled" and Arch somehow messes with the PS/2 emulation in your case .... so just turn it off.
good luck

Publish to Android device doesn't work

Flash CS6 - I'm trying to Publish content to Android device to install and open it there, I receive error everytime I try that says your phone is connected. First question cross my mind, why does it assume I have a Phone ? I connected ASUS Android 4.0 tablet to PC and doesn't recognize it...
Any ideas how to make this work ?

Hello,
Could you please follow instructions outlines in this article?
http://helpx.adobe.com/content/help/en/flash/using/publishing-air-android-applications.htm l
Let us know if you still have problems publishing Flash content to Android.
Thanks,
Suhas Yogin

Live Encoder for Mac + Shure XLR- USB device doesn't work

I use Shure X2u to convert external microphone signal to USB audio device. MacOS sees Shure as input device in Sound Preferences. If I set "Shure Digital" as input device Garage Band records my external microphone. If I run FlashMediaLiveEncoder it records only laptop internal microphone.
Is there a way of recording sound of external audio input device?

It is a Cowon D2. As said, it is pretty inconsistent and sometimes works, sometimes I just get the "Preparing ..." message when copying.
What worries me most is that I can't see the MP3 player anymore after this has happened. So the Mac must 'cache' or remember something about the device; a PC doesn't have this problem.
So I should find a way to clear that memory or cache or mount table or whatever it is... As said, currently the only solution is the re-install the player's firmware, or use a PC

Satellite 5200-903: Mini PCI Card doesn`t work

Hello,
I am a user of an:
Satellite 5200-903: P4-M 2.2/256+256 DDR/60GB/15T SXGA+/DVD-R-RW/nV FX 5600/cPad/WIFI ready/XP
My computer is equipped with an Toshiba Wirless lan Mini PCI Card.
I installed the card a few years ago - everything worked wonderfull.
At the beginning of 2006 I installed a new operating system (XP Pro + SP1, same system as before) because it was necessary.
I installed all driver for the W-Lan Card, obviously the card worked in the correct way (no driver incompatibility or other problems).
But, and thats the reason of this topic here. It isn`t possible to connect my card to any Hot Spot. I tried it with 2 different access points, but the result is the same. "No connection Point found".
Has anyone any idea what to do or in which direction I could look for the failure? Is there maybe any special Software necessary (I couldn`t remember, that in my last installation I had needed special driver or software)
If further informations are necessary, please inform myself.
(sorry for the terrible english, but it isnt my first language.)
THX for your help

Hi,
thx for the hints. But unfortunately none of these solved my problem.
1. I checked my device Manager, it`s shown a Toshiba Wireless LAN Mini Pci Card
2. The device is activated, with no problems
3. My wireless activation switch on the left notebook side is activated (led lights yellow)
4. Pushing the Fn+F8 Button results nothing
(wenn i press the combination during the Notebook switch is off - i got the message "wireless connection is deactivated, please activate")
What have to happen, when pushing the Fn+F8 Button during the wireless switch is activated? Is there any message on the screen?
Concerning the installed driver, how could I check what type of card is installed in my notebook. I know, that there a two types of driver and card existing, toshiba and atheros.
But, if the installed driver causes no problems I guess the right driver is installed.
Thx for any further Idea...
C.

Tethering internet from my Android device doesn't work

Hi Everybody!
I'm trying to tether internet from my phone, everything seems to be OK, you can see it in this screeshot :
Do not post full size images -- Inxsible
IP address, DNS server are ok, but I don't have internet , what am I missing? I even recompile my kernel follow Geentoo wiki
any Idea or hint?
thanks!
Last edited by Inxsible (2013-05-03 22:07:52)

Do you know that this is an Arch problem? I suspect it is an Android problem, in all likeliness, a problem deliberately created by your phone carrier.
Be that as it may, does tether work on other OSes? Also, to get my Android to tether (both USB and wireless), I had to change the iptables on the phone to allow it to route correctly from the wlan to the 3g network:
# uname -a
Linux localhost 2.6.37.6-cyanogenmod+ #6 PREEMPT Mon Jan 23 23:31:52 PST 2012 armv7l GNU/Linux
# cat /data/local/userinit.sh
echo 1 > /proc/sys/net/ipv4/ip_forward
iptables -P FORWARD ACCEPT
iptables -t nat -A POSTROUTING -o rmnet0 -j MASQUERADE
Make a file like that, reboot, and check your iptables config. [In case it is not obvious, I am talking of the phone itself]
Last edited by ewaller (2013-05-03 21:08:50)

USB external mass storage devices doesn't work.

Hey guys,
I couldn't find any answer to my problem so I hope you can help me...
I have USB Seagate external USB drive which was working perfectly with my mac until I installed VMware. The thing is that since first time I installed XP on VMware and unmounted my external drive from OSx and mounted in for virtual machine the drive is no longer visible in Mac OS no matter if I unmount it from virtual machine, plug/unplug from port, turn off VMware, restart macbook in any possible sequence combination. However I can use it easily in virtual machine or on other PC. Problem is not files type related, because I've already checked it, what is more I didn't format the drive and earlier it worked.
What is more now I can't even see my pendrive despite the fact that both Seagate drive and pendrives are visible in system profiler. My USB mouse works perfectly so problem apparently is only with data storage devices.
During the installation an error pop up concerning "IOUSBMassStorage" file but after installation of VMware everything was working until I mounted in on virtual machine.
EDIT: I almost forgot to add that I uninstalled VMware and the problem still occurs.
Thanks for any help in advance.
Message was edited by: bheliom

I was trying to install update USBFamilly and now also VMware again and in both cases I get error saying that USBMassStorageClass was installed improperly.
I found few topics about this file on the internet that it controls exactly what I have problem with but couldn't find solution for how to reinstll this file.
Any ideas ?

Web sharing doesn't work on reboot

I have to turn Web Sharing on and off to make it work after a reboot. I'm not sure when this started as I use Web Sharing intermittently for developing web sites.
Trying to access on my Mac I get
Safari can’t open the page “http://localhost/~me/” because Safari can’t connect to the server “localhost”.
Works fine after going to Sharing and turning Web Sharing off and back on.
I'm sure this has been covered but haven't had any luck searching.

Toshiba knowledge base - how to fix webcam - http://forums.toshiba.com/t5/Video-Display-Knowledge-Base/How-can-I-fix-my-webcam/ta-p/281393
Here is another post that gives some suggestions - http://www.pcauthorities.com/pc-errors/how-to-fix-webcam-problems/
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

Pci device doesn't work till reboot

Similar Messages

Maybe you are looking for