Pci express lane selection and speed on tri-sli z97xpower x99 gaming9ack xpower

Ok so I am wonder if anyone might know this answer, right now I am on a z97 gaming 9 ac and currently running 2 way sli, but am seriously considering and looking into going 3 way sli, and well this board wont go 3 way sli, itll do tri-fire but not tri-...

What's your BIOS & EC versions?
Where did you get those drivers?
Did you update the video BIOS?
Check the GT70 2PC product webpage and update all above.
http://www.msi.com/support/nb/GT70-2PC-Dominator.html#down-bios

Similar Messages

Re: pci express lane selection and speed on tri-sli z97xpower x99 gaming9ack xpower

Yes but so far nobody talked about X99 that's why I asked.

Quote from: Svet on Today at 22:46:14as you can see by yourself, yes
Finally that's a relief. Thank you all, you have cleared my incorrect information.

Problem of PCI express link width and speed

hello,
I instantiate the pci express core v1.7 into a pci express endpoint and the core was configured as GEN I x8 or GEN II x4. By using the example design Xilinx offered in the ipcore dir, I could read and write device by PIO mode.
However, when I check the device’s link width and speed by using lspci –vvvv in Linux, I found that no matter what configurations I set, the device link is always trained as GEN I x1, which means the throughput of device, reduce 8 times. May the most important problem is that all logic in the user layer upon transaction layer are written at 250MHz, and if link width and speed are limited 2.5G/T and x1, I need to change user logic circuit which is a huge work.
So my question is how to change the PCI express link width and speed in OS side, or I need to change a new motherboard?
(I guess it related with motherboard, and I check that the PCI express slot in motherboard support GEN II X16. Another issue, when I insert a PCI express GEN II x8 device, the device is also trained as GEN I x1).
lscpi -vvvv
01:00.0 RAM memory: Xilinx Corporation Device 6018
Subsystem: Xilinx Corporation Device 0007
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dfcff800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range B, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Device Serial Number 00-00-00-01-01-00-0a-35
Kernel driver in use: card

I also have this issue of the user_link_up is high and everything looks good but the LnkSta widht is 1x. did you ever get any guidance about this?

SoundFX suddenly not working with PCI-Express SB Titanium and Windows 7 HP 64

Hi guys,
I bought myself a PCI-Express Sounblaster Titanium bulk last friday.
I downloaded some drivers (sorry, I have no idea what Version?) and an Update to the latest official Version (2.7.0007). When I first tried tu use VoiceFX it worked and I was astonished. Its seemed a real cool gimmick.
Strangely, when I tried it again the next day the VoiceFX buttons where still there under the Audio Config thingie, but my voice did not change anymore when I chose for ex. Robot or Ork. It did not matter what I chose, my voice always stayed normal.
Since then I've deen doing nothing else than to deinstall, reinstall drivers, deleting driver traces, trying again. My worst case was that the VoiceFX did not show at all anymore, my best case was as described above.
I even treid the new beta Drivers.
Does anyone have a solution?
If not, can anyone tell me what dependancies VoiceFX has? Is it enough to install only the drivers or does it need something else as well?
With which Driver Version does it definitely work under Win 7 64?
Oh yeah, I have I microphone which I can switch to Mono or Stereo, does it only work with one of the two? Mine was mostly in Stereo mode. (It comes from a company (dunno which one) thats got nothing to do with computers, games or creative, it's one of those Microphones you connect to your tie).
Thanks@all

Weird... I changed nothing and yeterday it worked...
I just understand this, but what the hell?

This is not really a question but just a highlight. I have been for 20 minutes on the phone through the express lane support and I have been told that iCloud DO NOT stores music or video and cannot be used to pushes any music you bought through iTunes !

I have been amazed from the Express Lane support. I have been asking information about how to store/push my iTunes music in the iCloud. The answer has been that iCloud DO NOT stores you iTunes music at all !!!!! Is this real ?
I am Mobileme user since the beginning and just bought OS X Lion and all necessary software to maximise the use of iCloud and now I have to discover that what has been advertised for months on the web is just ballsheets.

Wow! It took you 3 week to come up with that ridiculous response?
Since I don't have access to the 11/13 web pages (my time machine is out of order), I can't provide that. However you know full well that iTunes Match has been live for the last 3 weeks, and it isn't "ballsheets."
As far as the "gift you may have to spend too much time on internet", it took you far longer to compose and post your whining rant that it would have if you just searched it with Google and got your own answer...

PCI Express and Soundblast

I just got a new machine that has PCI Express card slots in it. I am new to this technology so I have a total noob question. Can you use soundblaster cards in a PCI Express slot? And on a larger scheme, can you use PCI cards in PCI Express slots?
Thanks,
-murk

As everybody said... No. PCI-express and PCI are not really compatible.
And I'd like to reply on the posts regarding PCI-express soundcards. If any card like that would be produced, I guess we'd need mainboards with more PCI-E slots than we have now. Now it's all PCI-E on GPU's and 2 PCI-E slots for crossfire/SLI setu
ps.
Gi'ven I want to have a decent gaming machine in the foreseeable future, I'd need atleast 3 if not 4 PCI-E slots. Something like a Physics processing unit comes to mind, 2 GPU's and a soundcard... which would also conclude in a lot of users should be upgrading their systems to a higher substandard then now. Upgrading is fun and all, but if they people can't afford to upgrade that often, most companies would stay pretty low.
That's just my 2 cents. But seeing the developments running wild regarding computers I wouldn't be too surprised if we'd see it happen soon.

Windows 7 64-bit X-Fi PCI-Express Audio console

Hello,
I have a SB PCI-Express Extreme audiocard, and I recently installed Windows 7. I have the basic driver and I do have sound, but the full control suite of software, that included the audio-console and startup-console I had in XP that allowed me full control of my card I do not. Which is rather annoying, because there's much more functionality there.
I tried installing the XP version of the control software, but it started with saying I have newer drivers installed, which made me cancel it as I figured it would be bad to install XP 32-bit drivers on W7 64-bit system.
So, I wanted to know if Creative is working on make W7 64-bit version of the control suite, and if so, whether there is an estimate on when it'll be completed/released? And if not, if someone knows a workaround to get the control suite of XP installed anyway without overwriting the drivers.

Re: Windows 7 64-bit X-Fi PCI-Express Audio console" http://forums.creative.com/t5/Sound-Blaster/SB-P7X-Series-Support-Pack-2-0-07-3-2009-AudigySE-Value-LS/td-p/53329
That is for your card, sorry about that. Then you can download and install the newest Creative driver on top of this package. You will first unpack Dan K.'s support pack, install it, reboot. Make sure your sound is functioning and that in Device Manager you have Creative X-FI, not high definition multimedia device. Then reboot again, and install the newest Creative Labs driver. Now you can configure your system for number of speakers, tone, bass, EQ, Crystalizer, etc.

Heavy Modifications on T420s system (BIOS Modifications, CPU Swap, PCI Express Routing)

Hello everyone, i was looking into going for a large project on modifying a t420s system.
I was planning on "Pulling" pci express lanes from the chipset and routing them outside for a custom made addon that needs 4 pci express lanes. (at worst 1pci express lane - excluding the one provided by the expressPort34)
Also i was looking onto swapping the i7-2620 with an 2960xm. (i know that it calls for some soldering and complex smd work but fortunatley i know i can do this). I know the chipset (QM67) Supports the CPU and 16GB Ram, has plenty of pci express lanes and many unused.
Some things i wanted to know are:
Is there a way to get the cmplete schematics of the system? The logical interconnection of pci express devices.
Is there some sort of protection against BIOS reflash? I plan on using w520 bios for refference on t420s bios modification.
Also is there a way to get the complete full map of logical links on the system? Like all standart devices that are USB (Example: Fingerprint reader).
Obiously i know that this completely voids the warranty.
Any help will be appreciated.
If someone is an expert on thinkpads please help me on this project. I will post and article after i finish the project and give proper credits.

You might want to look into the pinout on the docking port, if you can find details. Perhaps there is a pci express lane or two on there.
When asking for help, post your question in the forum. Remember to include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help others with the same question in the future.
My TPs: Twist 2HU: i5-3317U Win 8 Pro, 4GB RAM 250GB Samsung 840 | T420 4177CTO: i5-2520M, HD+, Win 7 Pro x64, 8GB RAM, Optimus, 160GB Intel 320 SSD, Intel 6300 WiFi, BT 3.0 | T400 2764CTO: P8700, WXGA, Win 7 Ult x64, AMD 3470, 8GB RAM, 64GB Samsung SSD, BT, Intel 5300 WiFi | A20m 14.1" PIII 500 (retired). Monitors: 2x Dell U2211h IPS 100% sRGB calibrated w/ Spyder3.

Z68A-G45 (G3): BIOS screen unreadable on PCI express graphics card

I have a Z68A-G45 (G3) board with Intel Core i3-2320T processor. BIOS version is E7750IMS v11.2.
When entering the BIOS setup screen with DEL, everything is fine when the display is connected to the motherboard HDMI port.
When I plug in my MSI Nvidia 8500GT-based PCI express video card and connect the display to its HDMI (or DVI) port, the BIOS screen is corrupt and almost unreadable. I can see some characters and images -- the BIOS is there, I can see the temperature readout -- but navigation is very difficult. This problem occurred with BIOS version 11.0; I just flashed to 11.2 and the problem persists.
Here's what it looks like
Can anyone help?
Thanks,
Steve

In case anybody's curious it turns out the issue was specific to the card. I tried a different PCIe card and the BIOS screen showed up fine.
So finally I ditched my old reliable nVidia card and used the Sandy Bridge integrated graphics instead. No problems so far.

Need PCI Express Firewire

I did a search here, and on Google. The cheapest card found was $55, and that had only 2 ports. I'm not a cheapscate, but this is my first purchase for my new G5 and the last FW card I bought for my G4 was $22. Is express always that much more? I definitely need it, because I seemed to have gotten one of the Dual 2G with a bad FW port. I did all the tests and the only thing Apple will do is take the thing apart, and I'd rather not have them do that for one port.

Hi Claude;
If Apple is going to do this under warrenty, then I would strongly suggest that you allow them to do it. Personally, I think that not allowing them to fix the problem now might end costing you in the long run.
To answer your question, yes PCI Express cards are generally more expensive. It appears this is true for two reason. First PCI Express is new and new always costs more. The second reason is that generally PCI Express card have greater performance then either PCI or PCI-X.
Allan

X-FI Titanium pci-express MIDI connec

Hi to everyone. I want to buy a great pci-express sound card and this Creative X-FI Titanium Fatalty Pci-Express is interesting. But i need Midi connector for my musical works; i have the old db5-to-midi cable and the internal db5 bracket. Is this board compatible with this connectors or have other connections? I don't want to buy a usb-midi or i/o module; other pci-e boards have midi or have compatibility to db5 bracket, so i only want to know if x-fi titanium is the same or is a bad board for this. Thanks.

Hi Guys
Many, many thanks for all your help with this.....NOT!!!!
I really hate it when you come to forum to ask for help and everybody fecking ignores you....was the question too hard for you. I thought it was really simple, does the DVD-A player work with this card under this OS or not. I at least thought some of the Creative mods might help, I've just spent my hard earned cash on this card after all. As it is an X-Fi card I thought the DVD-A player would work okay but it doesn't so maybe I'm doing something wrong but I don't know because I didn't get an answer.
Thanks a whole bunch guys

How do I get my money back for the purchase of an application by my daughter(5yrs old) for £69.99! Have tried customer support help line and was directed to express lane to report problem, express lane will not work......any advice?

My 5 year old daughter asked me to download a free app, tap pet store. THis I did and then she immediately downloaded the pocket gem upgrade costing
£69.99!!!
I have tried the customer support help line (35minute wait) then directed to express lane to report issue. Express lane keeps informing me that it cannot send the report.......getting very frustrated any suggestions?
Thanks
Ed

Sorry, but according to Apple, iTunes Store: All Sales Are Final
You can avoid accidental purchases.
From the iTunes menu bar click iTunes / Preferences then select the Parental tab.
Select: iTunes Store
Click OK.

So I keep getting the "Please contact iTunes support to complete this transaction." note in my apps, and I tried contacting iTunes, but I can't fine the express lane or any means of contacting them.

So as I said, I keep getting that statement, and all the forums keeps saying use the ITunes store express lane, but I can't seem to fine the buttons for the express lane.cplease help.

You can contact iTunes support here : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page

Need Urgent Help : Using VIVADO Design Suite for PCI Express 3.0, 8 lane, and AXI Interfaces for Video Processing

My scenario is as follows :-
1) I am building a Image Processing Application and using VIVADO HLS for that.
2) I have synthesized my design using VIVADO HLS, and export it as IP-XACT format.
3) I have imported it in VIVADO Design Suite, and added to the IP catalog, in a new project created.
4) Since I am building an image processing pipeline, I am using AXI Stream interfaces, 1 input stream, and 1 output stream, and mentioned that in the HLS tool itself..
5) I have a Virtex 7 690T FPGA, and have accordingly chosen the board throughout the HLS process, and the project.
6) We want to use a PCI Express 3.0, through DMA access to the CPU.
7) Now I am stuck here regarding how to proceed forward, I have gone through most of the Xilinx documentation, but am still not clear about what to do from here on.
8) There are these 3 variables for me, AXI Stream Interface, DMA, PCI Express 3.0, all I have right now is the IP of the Image Processing pipeline that I generated through VIVADO HLS.
9) Also at a later stage we would like to stream in Video, and process it through our image processing pipeline.
Please help me with an overview of steps that I need to follow to get my design together and working on a real FPGA hardware with my Computer(windows OS), as in what Xilinx IP blocks do I need to use, how will I be able to exploit the maximum bandwidth from the PCI Express Interface in my specific case of send image through a stream, what tools will I need to use at every stage.
I would be highly grateful if you guys can help me, we have a dealine to meet.
Please let me know if we need any extra information.

School project?

What is the difference between PCI-x and PCI Express?

I hear the new dual core Power Macs have PCI Express slots. How are these different than the PCI-X slots in my old Power Mac?
jmf

PCI Express is faster than PCI-X and not a bus architecture. Each slot has its own dedicated bandwidth to and from the system controller.
PCI-X has a maximum clock speed of 133 MHz and a maximum throughput of just over 1 GBps.
PCI Express cards and slots are defined by their bandwidth, or number of data lanes — typically one lane, four lanes, eight lanes, or 16 lanes. At 250 MBps per lane, a four-lane slot can transfer data at up to 1 GBps and an eight-lane slot, up to 2 GBps. The new PowerMac G5s have one 16 lane slot, two four-lane slots, and one eight-lane slot.

Pci express lane selection and speed on tri-sli z97xpower x99 gaming9ack xpower

Similar Messages

Maybe you are looking for