Pci serial controller

for some reason i cannot connect to the internet. found when i got home that i don't have a pci serial controller driver or something so it wont pick up my modem. i guess my lil brother did something to the comp while i was gone. anyone have any idea where i can find this driver or figure out what's wrong too? also, that new hardware stuff popped up for pci to pci bridge controller or whatever it is popped out. i couldnt find the driver for that either. so i'm using the one that was on my harddrive.....viamach.inf? also i'm at a friend's house downloading the new via 4n1 driver and hoping to see if that works....

well under device manager, it came up under unknown devices/other devices --- pci serial controller and pci communication device. what i did was clicked update driver and select drivers from list since windows was unable to locate a driver. I selcted HCF Modem driver and selected Rockwell Conextant HCF modem driver. it came up with a popup saying that installing this driver may or may not work since it was not made for the device(even though it was) and it worked. i still have another problem. when i first found this problem i just tried switching the modem to another pci slot and later on switched it back to the original. now the computer thinks i still have it in the other slot. so now i have "two" modems even though it uses one. i've probably already lost you in all this typing :D

Similar Messages

PCI USB2 Controller card conflicts with network card

I've installed a PCI USB2 controller card since my motherboard (IWill K266-R) only has support for USB1. However, the card seems to conflict with one of my network cards, because traffic on the internet-connected NIC is very slow, and often drops completely. Traffic to and from the other (local) NIC seems to work fine, though.
I have tried moving around all three cards in different PCI slots, I think I've tested almost every possible combination by now. I've also tried disabling as much as possible in BIOS, such as onboard sound, serial and parallel ports etc. I've tried lowering the FSB.
For now, I've removed the controller card, and is using the USB1 ports on the motherboard instead. This is very frustrating, though.
Does anyone have any suggestion on what I can try next? I've browsed forums, both this and others, but I haven't found any more hints on what to try. Could there be some setting in Arch that could affect these sorts of things?

"I guess the ATA100 card will work fine correct?"
If you mean large drive support, it may provide that or may require a firmware update to do so. You should check the manufacturer's web site for specifics. All ATA-133 cards do provide 48-bit LBA for large drive support. I'd return the Ultra ATA-66 card to the eBay seller, although many refuse to pay for return shipping, even when the mistake is their own, either through ignorance or deliberate misrepresentation. In cases such as this, it's sometimes more cost-effective to swallow the loss and keep the incorrect part.
"Will adding a jumper apply for a ATA100 card as well? I'll need a blue and gray ribbon correct?"
If you use an 80-conductor ribbon cable with color-keyed connectors, set the drive configuration jumper to CS and connect the drives to the cable as you wish (in terms of physical placement in the computer). If the ribbon cable doesn't have color-keyed connectors, set the jumper for the device connected to the end connector as Master and the drive (if any) connected to the middle connector as Slave.

PCIe Serial Card Stopped Working in Yosemite

I have a PCIe serial card in a Mac Pro based on the 16950 that's been working fine up until Yosemite. It's been working with the built-in Apple16x50Serial.kext driver.
With Yosemite, it looks like the driver loads okay, but no serial port appears under /dev/, and no IOBSDSerialClient for the card appears in ioreg either.
This is the same device used in the older XServe's with serial ports.
Info on my card:
Card: pci1415,9501 Type: Serial Controller Driver Installed: Yes Slot: Slot-3
pci1415,9501:
Type: Serial Controller
Driver Installed: Yes
MSI: No
Bus: PCI
Slot: Slot-3
Vendor ID: 0x1415
Device ID: 0x9501
Subsystem Vendor ID: 0x1415
Subsystem ID: 0x9501
Revision ID: 0x0000
Link Width: x1
Link Speed: 2.5 GT/s
Has anyone else encountered this issue or know of a workaround?
Thanks

Same here, although I can't even enter the shortcuts screen on my iPhone, as the Settings app crashes when I try to view the shortcuts. They are still on and work on the phone, but I can't access them to edit, etc. On the Mac, they neither show up nor work.

64-bit Vista Drivers for PCI Serial device

I've just got an T500 and put Vista 64-bit on it. I've found (I think) all the drivers for it that it needs, except that there are 2 drivers in the Device Manager that show as not installed/needing update they are:
Under Other Devices
- PCI Serial Port
- PCI Simple Communications Controller
Anyone know what divers I should get to get these loaded properly or what devices/capabilities I am loosing because there are no drivers?
Thanks,
George

George, welcome to the forum,
have you tried using ThinkVantage System Update to see if it can automatically find the drivers for you?
Hope this helps
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Need a PCIe Serial 2 Port for my HP 8.1 Windows computer, Any ideas?

I need to find a PCIe Serial 2Port adapter for my HP computer with Windows 8.1.
This question was solved.
View Solution.

Like this?
http://www.amazon.com/PCI-E-Express-Serial-Controller-Adapter/dp/B00FH7WZ86/ref=sr_1_5?ie=UTF8&qid=1...
I cannot say whether you can get the serial ports configured under Windows 8.1. Here is an article that may be of interest:
http://www.charleswilde.com/windows-8-1-includes-support-for-serial-ports/
If this is "the Answer" please click "Accept as Solution" to help others find it.

Windows 7 driver for PCI Simple Controller

I installed the Lenovo Windows 7 Professional upgrade on my R400 (7443-CTO) from Windows XP Professional. The ThinkVantage tools repeatedly shows I need a driver for the "PCI Simple Controller". I have been unable to find that driver on the Lenovo support site. Any assistance to help resolve this issue would be appreciated.
Solved!
Go to Solution.

To create shortcuts or folders under the startmenu in Win7 you can rightclick "All Programs" under the startmenu. Then you can choose "Open" or "Open all users". If you choose "Open" you will be able to change the startmenu for the current user account only and when you select "Open all users" you can change the startmenu for all user accounts on the computer. The startmenu in Windows is basically just folders and shortcuts stored in a folder on your computer. The startmenu for all users are stored under "C:\ProgramData\Microsoft\Windows\Start Menu" and for the current user under "C:\Users\<useraccount>\AppData\Roaming\Microsoft\Windows\Start Menu"
So let's say you want the "Thinkvantage" folder under the Windows startmenu where it should normally be after installing Lenovo toolbox and then the shortcut for Lenovo Toolbox under that folder. Then you can rightclick "All Programs" under the startmenu and select "Open all users" from the context menu. You should then see a explorer windows with the folder "Programs". If you open the "Programs" folder you will see the same contents as you see under the "startmenu -> All Programs". Since this is the area for the common startmenu for all user accounts there might be some more entries under the startmenu compared to what you see in this windows. By selecting "Open" instead of "Open all users" as explained above you should find the rest. So when you rightclicked, selected "open all users" and then doublecliked on "Programs" then you can rightclick somewhere in that window and choose "New -> Folder" from the context menu. Then you can give the folder the name "Thinkvantage". Then open the "Thinkvantage" folder and create a shortcut for Lenovo Toolbox. After you have done these steps you should find the Thinkvantage folder under "All Programs" and then the shortcut for Lenovo Toolbox under the Thinkvantage folder. This is how you can easily change the startmenu in Windows to add, remove or change entries under "All Programs".
Normally after installing Lenovo Toolbox it should be under "All Programs -> Thinkvantage" and not sure why that is not the case for you, but then you can add it manually like explained above. When i installed Lenovo Toolbox a shortcut and the Thinkvatage folder was created under "All Programs" during the installation. Also if you install the "System interface driver" and "Hotkey feature set" you can start Lenovo Toolbox by pressing the blue thinkvantage button on your computer. Unless you already installed "System Update 4.0" i would recommend to do so. System Update will find the drivers and software from Lenovo for your computer and give you a list where you can select those you want to download and install. System update will then download and install the drivers and software you selected and you don't have to download and install each one of them manually one by one. It will save you a lot of time. You can find system update for Windows 7 using the link below.
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-73695
User Access Control is a new feature of Windows that started with Windows Vista so therefore you won't find it in XP. Only Vista and Windows 7 got UAC.
Yes it's a bit late over here I'm sure i will enjoy the weekend and hope you will do the same.

Satellite Pro A200-1MI - Need driver for PCI memory controller

I have the Toshiba Satellite Pro A200-1MI(PSAE7E) having a problem with PCI Memory Controller on my notebook.
When I go to Device Manager it shows question mark in the tab Other Devices and when I go there, it's yellow ?(question mark) and !(exlamation mark) at PCI Memory Controller. I took and downloaded all the drivers from your site:
http://eu.computers.toshiba-europe.com/innovation/download_drivers_bios.jsp?service=EU
for XP but I am not sure what type of drivers do I have to install for PCI Memory Controller, is it bios driver or something else? I just need to know what to install to overcome that problem with my Device Manager and PCI Memory Controller.
Thanks in advance!

Hello akibono
I presume you have installed clean WXP on your notebook and now you want to install all drivers, tools and utilities. Am I right about that?
Anyway, after WXP installation you must install all drivers, tools and utilities in specific installations order. After doing this everything should be OK and every hardware component will be properly configured.
Please install all stuff as follow:
WXP
Chipset driver
Display driver
Sound driver
Modem driver
Storage manager
LAN driver
Touchpad driver
WLAN driver
Toshiba Assist
Flash Media driver
Webcam driver
Hardware setup
Controls
And so on
I hope everything will be OK.

Resource conflict- pci network controller in slot 09

hi there!
im looking for help with this problem which ive had for teh last 3 months.
basically one day, when i turned my laptop on it didnt log straigh into windows, it came to a screen that said
'resource conflict - pci network controller in slot 09'
press f1 to resume , f2 to enter setup, f1 would take me to windows and f2 to bios.
after this my wireless card dint work, so i ended up buying an external one which i used. now i decided to format thinking it would help the situation, but no luck. ive looked around on the net asked alot of friends but no one seems to be able toi give me a solution. is there anybody who could tell me what to do?
thanks
lefteris

I have the same problem im my lap (ThinkPad R50e) and i perform the following steps to resolve
F1 --> Config --> Network --> Disable --> F10
then repeat the same steps but enable network
F1 --> Config --> Network --> Enable --> F10
it working fine with me

Dead MS6330 after PCI IEEE1394 Controller install

Hello,
Yesterday I installed a PCI IEEE1394 Controller on a MS-6330 with 1300Mhz Athlon. After installing the necessary software and restarting my WinXP couldn't load. I tried removing and adding the newly installed card, the LAN and video cards. Now as I start the computer the power supply looks fine, all the coolers start etc. but no signal (even BIOS) appears on the monitor, neither does the 'No input signal' message that appears when video signal is absent. Could you offer some solution to the problem?
10x in avdnce

Did you try clearing the CMOS ? ( Clear CMOS Guide)

On-board RAID and PCI RAID controller

Hello everybody,
I am new to the forum. So, please excuse me if that topic was already covered...
I have MSI MAX2-LR (MS-6398E) board. It works just fine, no problem so far. Though I have 2 problems with add-on cards:
1. I was planning to use on-board RAID and additional PCI RAID controller = FastTrack 100 TX2 to cover 6 hard drives into 2 mirrored sets: 4drives one and 2 drives the other.
It doesn't work! I can use either on-board RAID or PCI RAID. As soon as I have any drive connected to on-board RAID, the PCI RAID disappeares. If I have no drives connected to on-board RAID, I can see both RAID controllers, they have different I/O and IRQs, and PCI RAID is working just fine. If only I connect one drive to the on-board RAID, it gets activated on startup, and the other one disappeares. :O
I believe it's a BIOS bug. I wander, if that can be fixed easily????? :D
2. I have a new Matrox Video card = Parhelia. It doesn't work in AGP slot! System doesn't recognize it, and beeps non-stop. I am dealing with Matrox Tech Support on that matter. ?(
Maybe, it's a known issue, and somebody can save me time by telling what's that about.
Appreciate any imput. Have a great weekend.!!! :]

Hey I also have the same Raid card and also the Matrox Parhelia, and I see that you also have some problems with the card I got also problems with the card, but they couldnt help me at theire forums (http://forum.matrox.com/mgaforum/Forum10/HTML/005085.html), I hope we have got more luck here :D

2nd Request - PCI Memory Controller for ThinkPad T500 2081-CTO OS Vista 64bit

Evidently the PCI Memory Controller driver is not installed on my ThinkPad T500 2081-CTO OS Vista 64bit and shows up as an error when running the Lenovo System Tool Box.
Searching this forum I found one psot as follows BUT thisis for a T-200 laptop.
Re: Driver for PCI Memory Controller
Options
‎02-25-2009 06:59 AM
You need the driver for Intel Turbo Memory. Only Windows Vista can use Turbo Memory, so we only have a Vista version for the driver:
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-67820
Is this driver appropriate?
Do I need the PCI Memory Controller driver .. and if so where do I find it for my laptop?
Thanks.
Solved!
Go to Solution.

I would suggest that you forget about turbo memory. Intel quit talking about it and they have not released a driver since 2009. That is 2 years before service pack 1 was released. I ran tests and I was never able to measure any improvement with a card installed. As far as I am concerned, it is just something else to break and interfere with other components.,

Windows 8.1_64 compatible PCI Serial port drivers for M58P (6209)

On the last week I upgraded my Lenovo M58p (model 6088) to Windows 8.1_64 (Enterprise) and encountered the problem in which the drivers for the following were not installed and couldn't be located ....
PCI Serial Port
In the model page there is no information on the PCI Serial port:
http://support.lenovo.com/br/pt/products/desktops-and-all-in-ones/thinkcentre-m-series-desktops/thin...
Thanks
Solved!
Go to Solution.

I found the information about the driver on another topic:
https://forums.lenovo.com/t5/Windows-8-and-8-1/ThinkCentre-
M58p-6234-BR9-Windows-8-eval-build-8250-missing-PCI/m-p/854209#M589
The first link did the trick:
http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS003086
c3amt02us17
Thanks.

Missing Windows 7 64-bit PCI Memory Controller Driver on X61

I'm sure this has already been discussed but I could not find the thread. Does anyone have any information on why I cannot find a Windows 7 64-bit compatible PCI Memory Controller Driver for my X61 7675 CTO?
Thanks,
-Ron

PCI Memory controller is Turbo Memory:- http://support.lenovo.com/en_US/downloads/detail.page?LegacyDocID=MIGR-67820
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

USB Serial Controller Driver for windows 7 64bit

USB Serial Controller Driver for hp 15-g049au windows 7 64bit
This question was solved.
View Solution.

Hi,
Install the Chipset drivers on the following link and reboot.
http://support.amd.com/en-us/download/chipset?os=Windows%208.1%20-%2032
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Calling dll of Leetro MPC08 PCI motion controller card problems.

Hi,
I have been trying to develop an application using Labview 8.5. I need to control a motorized linear stage which uses the Leetro MPC08 PCI motion controller card. The manufacturer gave me example VIs which I configure to call "c:\windows\system32\MPC08.dll". About four months ago, I remembered that i tested them and they seemed to work somehow (but I did not finish the full test since i was busy doing other things). Nevertheless, when I got back to continue my development a few days ago, i just could not get the same old VIs to work. I could only get one library function of the card to work which is the "auto_set" which returns "4" which is the number of axes that the card can control. The next function I need to call is "init_board" but this one keeps returning "-3". The manual indicates that any negative number returned means there has been something wrong. I would guess it is "PCI initialization fails" but honestly do not know for sure. Can anyone help? My computer is a PC running windows XP.
Thanks in advance for any kind help offered.

Hi,
Wrapped VISA call means that the SubVI contains a set of VISA calls.
If you are calling the VI's individually it is possible that the VI's need to pass a reference to each other, so they might not work if run individually. Hard to know without the DLL docs, so to speak. It could be possible that there is no need to pass references between subVI's.
Direct VISA calls are probably not necessary if the device runs with the vendors software. The main goal was to verify functionality with either VISA or vendor app.
Ok I was looking at the Leetro web site, you can forget the VISA stuff as it is a PCI card, duh... you said that at the begining. :-)
The manual says Win2000 or XP. is this being run on two different systems?
Mark
Mark Ramsdale

Pci serial controller

Similar Messages

Maybe you are looking for