Peak Power and System power

I was trying to evaluate the difference between the Creative Inspire T5400 and the newer T5900 5.1 speaker systems. At first I was led to believe that the *only* difference is that they have placed the centre speaker on it's side for the newer T5900's, as all RMS ratings are the same for both sets at 74w RMS (22w sub, 4x 8w sats and 20w central). However, I noticed this difference in the discription on the Creative US site: For the earlier T5400 set, they say 74w RMS with 5w 'Total System Power'......and for the T5900 set, they say: 74w RMS with 48w 'Peak Power'. So what is the story here? 'Peak Power' I understand, as this is twice the total RMS wattage (2 x 74w = 48w). But what is this 5w 'Total System Power' of the T5400's? Where has this figure come from? And what is the difference here....is one set more powerful than the other? If so, which is it's I bought the T5900's thinking they were better in some way other than the new horizontal positioning of the centre speaker - but I could have gotten the T5400's a tad cheaper. I hope this new horizontal centre speaker is not some gimmick to mask a downgrade of some kind - as it's widely known Creative has been making succesful attempts to lower it's manufacturing costs. Anyone know the score here?
Confoooooozed!:smileyindifferent:

I wouldn't worry about it - if I had the T5400's, I would not consider 'upgrading' to T5900 as they are more or less the same speaker system. The center speaker is on it's side - that is all. If anything, your T5400's will be made to a superior standard - Creative are known to have been cutting manufacturing costs recently.
I was immensly dissapointed to find no gold connectors on my T5900's, but my old, supposedly 'inferior' Inspire 5300's do have gold connectors. Also, the speaker cables on my T5900's are very thin - unlike the cables on my old, 'inferior' Inspire 5300's. This is very bad on Creative's part and I hope they realize that I will not automatically turn to them when I next need audio equiptment. They should be making their products better each time, not cutting their own costs in the interests of corperate greed. If the moderators on this forum don't encourage this kind of talk - I would ask them to take note of this: Some things will not go un-questioned by their loyal customers. I have spent hundreds of pounds on their goods and so I have a right to speak up about their customer unfriendly practises.
Of course, if you want to upgrade - go for a 6.1 or 7.1 system...or really push the boat out and buy the Gigaworks - which are made to a very good standard! Also, to be fair to Creative again, I can highly reccomend the DDTS-100 decoder - I got mine recently and I'm more than happy with it. It's a great thing to accompany any of their 5.1, 6.1 or 7.1 systems.
Regards.

Similar Messages

I have an iMac running Lion and W7 with boot camp . It has been operating flawlessly until I went to reboot into Mac tonight. Screen went black, and system is unresponsive. I've tried force quitting and turning power off. Hard drive starts but that's it..

I have a 5 month old iMac running Lion and W7 with the latest version of boot camp . It has been operating flawlessly until I went to reboot into Mac tonight. Screen went black, and system is unresponsive. I've tried force quitting and turning power off. Hard drive starts, there's a small amount of drive activity and that's it.

Hi Jane, your info may still be there, look in the Users folder at root of the drive, how many users are there there?
It sounds like this may have happened...
Return to default desktop, apparent "loss" of home directory, (it can happen spontaneously too)...
http://docs.info.apple.com/article.html?artnum=107854

Peak Power Scheduler does not save

I have a T420 and Power Manager 6.55 installed.
Because my notebook is almost always working on the dockstation, it keeps charging all the time.
Not good.
So I decided to use the Peak Power Scheduler to use the battery at least once per day. But everytime I try to schedule a Peak Power Scheduler (no matter the configured schedule settings), after I close the Power Manager window and open again the schedule disappears.
This does not occur with other schedule options (like screen time, power management options, etc.).
Any idea?

It sounds to me that the two power managers are conflicting with each other. Try to make your custom power settings inside of the Lenovo Power Manager.
You can do this by opening the Lenovo Power manager and selecting the power plan tab, directly under the tab is a button that says New. When you select this a new window should open to allow you customize your own power schemes. You will be able to customize the System settings such as: Maximum CPU speed, Display Brightness, Graphics Power plan, also desired Idle timers, events, alarms an other advanced settings. Once created you will see your new power plan listed under the default power plans.
If this does not work, I would then suggest uninstalling the Lenovo Power Manager and utilize Microsoft Power Manager.
Good luck! Let me know if you have any questions
Thank you for being a part of the Lenovo Family,
Catie
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Donate KUDOS and Click "Accepted Solution"

Where can i find a Labview driver for the "8990a PEAK POWER ANALYZER" it's not on NI's site.

where can i find a Labview driver for the "8990a PEAK POWER ANALYZER" it's not on NI's site.
if there is no driver maybe you can tell me the closest instrument that comes to this one from the list at,
http://search.ni.com/query.html?lk=1&col=alldocs&nh=500&rf=3&ql=&pw=595&qp=%2BContentType%3AInstrumentDriver+%2BIDNetManufacturer%3A%22Hewlett-Packard%22&qt=peak+power+analyzer&layout=IDNet
so i could modify and use the driver

Hello,
It looks like Agilent/HP makes the 8990A, but I was not able to find a driver for it that we or Agilent has written for this device.
Since I am not familiar with the 8990A, I cannot recommend which drivers might be similar, but you are pointed in the right direction. Agilent themselves might know more about which models use similar command sets so that you can modify a driver easily.
Hope this helps.
Scott B.
Applications Engineer
National Instruments

802.11 B Peak Power?

Hello
I was looking at the Cisco's 871w specification earlier. I noticed that it has a peak power of 245mW with the average of 80mW for the 802.11B.
What does the "peak" really mean? There is no where in the 871W CLI that will allow me to increase the power all the way to 245mw. I can only increase it to 20dbm/80mW.
Thanks.

Peak power is the maximum level of work or energy output that is measured during an observation period. You can use these command show environment power all to know more about power consumption by device. Peak power of 245mW is the max. peak power for Cisco's 871w and 80mW is default avarage power.

Genius needs to help! problems with my video card and system

Hey guys! I'm going to post my specs first so that you get a good idea of what I'm running on:
MSI Neo2 LS 865PE.....MAT=Slow
Pentium4 2.4C.....FSB=233=2.8C hyperthreading enabled ~>1.55V
Corsair TwinX 1gig PC3700.....memory on "AUTO" in BIOS with timings at 3,4,4,8 ~> 2.7V
Radeon 9700NP.....stock speeds ~>1.7V
AlienX case with 2 fan400 watt power supply and 6 case fans
Zalman Alum/Copper heatsink fan
1:I've had this motherboard for a few months now. I upgraded my video card from a nVidia Ti4200(128meg) to a Radeon 9800 a month ago, but I couldn't get it working at 8X AGP, no matter what voltages I threw at it. I returned it for a Radeon 9700NP hoping that it would work, but it still won't.
I'm using BIOS 1.9 and since there is no option to select your AGP speed, I could only try using ATI's drivers. Once booted into Windows, there is a slider you can move to select you AGP speed. On my machine It says that It has performed some tests and has concluded that AGP 4x is the best for my system....but my system supports AGP 8X!
I've moved the slider over to 8x (which requires a reboot) at least 5 times with each card but the slider refuses to move past 4xAGP after the reboot.
2: My second problem: I had an old stick of KingMax PC3200 and decided to buy 3 more sticks. Unfortunatly, the 3 I bought did not match the one I had, so I only put 2 of the new sticks I bought into my system. Immediatly, My system would crash, lock up, files were corrupt, and I got PLENTY of blue screens of death with a long message containing: 0x0000007 with all these other numbers and "0"s. I did a search online and found out I had a hardware incompatibility problem. I never got this with my old stick of ram.
I returned the 3 sticks of Ram and replaced them with the Corsair. Put my new Radeon 9700 in, formatted my hard drive....and within 24 hours, my system locked up 3 times, rebooted itself 5 times, and gave me the same BSOD as mentioned above with the same long message.
I didn't change anything except for the memory and the video card. I've been wanting to overclock, (thats why i bought the faster memory ) but I'm not sure what to do at this point.
I have my FSB at 233 but I'm scared to go any higher because of previous system instability at stock speeds. My RAM was running on 400 and MAT=Turbo with the most relaxed timings at 3,4,4,8.
I've given myself hours of sleepless nights formatting when my system wouldnt boot into windows; overclocking....etc. I NEED HELP. PLEASE. PLEASE. Anything could work at this point.
I'm trying to get more info on how to run my system at a 5:4 ratio, also.
If anyone has problems like me or knows what could be the problem with my system, please reply to this post, it would help me a lot. I've been trying to fix these problems for a few months now so anything is greatly appreciated.

Thanks a lot to you guys that responded. I brought my computer home this past holiday and I want to let you know where I stand as of now. I guess this thread is like my blog for my computer. I want to clear some things before my first post makes everyone confused.
1- I have only 2 sticks of memory in my system: the Corsair PC3700 TwinX 512x2
I returned the 3 KingMax I bought, and still keep my old stick just in case.
2- I am using the 400 watt power supply that came with the case. I read some reviews of the case and I know the reviewer did not have problems with the power supply. In my BIOS, there are some voltages it is weak on. Lets say: it it should be 5.00+, my power supply will be feeding it 4.96v or something like that, but I dont know, or think, that is a major problem...
3- My computer will refuse to boot if memory speeds are set at anything below 400. SO....if I want to use a 5:4 ratio and have to set my memory speeds to "333" in BIOS, my system refuses to boot.
4- This morning, I did manage to overclock my FSB to 250. Specs are as follow:
Memory Timing @3,4,4,8,4.....speed set at "AUTO".....MAT at "SLOW"
MY 2.4C's FSB was raised to 250 = 3.0gig
AGP/PCI frequency: 67.xx/3x.xx (cant go any lower)
CPU voltage: 1.5500
Memory voltage: 2.75
Video Card voltage: 1.7
Everything was fine for the whole day until I heard something click in my computer around midnight, and then seconds later, my computer froze and made a continuous beeeeeeeeeeeeeeeeeep. (you can imagine)
This "click" and system crash has been plaguing me for months now. I dont know whay it happens. I was just using AIM when I heard the click and my heart stopped.
My memory speeds have been set to "AUTO" even at the FSB of 250. But I don't know if this still means my system is at a 1:1 ratio. I know the BIOS then adjusts the memory to work at 500 if my FSB is 250...so I assume it is? I love 3gig, but somehow I feel that 2.8 is faster, since the FSB=233 running parallel to my memory, also at 233
A FSB of 250 is good enough for me, that's what I've been waiting 6 months for. If anyone knows how to set other ratios to achieve a FSB of 250+, please let me know, but as I said, my memory won't boot if its set at "333"

Loops and system timestamp not synchronized

Running Labview 8.6.1 on Windows 2000, loops and system timestamp (Windows clock) seem to use different time bases; one second in a loop is not exactly as long as a second in system time. If i run a simple VI as in picture, with a 1-second loop which just prints the system time, the printed timestamp goes faster by about 1ms every 4-5 seconds. The same happens using a Timed loop or a While with a Wait until next ms multiple.
Why is that? Can i set a loop to match the system time?
Attachments:
1sec.png ‏3 KB

johnsold wrote:
In the eastern U. S. interconnected power grid the accumulated time is held to within a small fraction of a second when averaged over days. Over a year the accumulated error is less than parts in 10^12 or better. The instantaneous frequency can deviate from the nominal 60 Hz by less than 0.1 Hz.
The system basically uses an integral controller referenced to a NIST atomic clock to force the steady state error to zero.
Lynn
So is that a very technical way of saying "Ben, you are full of Sh#% !"*
I have not measured the frquency of my AC service in the last three decades or so. I do remember seeing it faster in the summer and slower in the winter. Has it really changed? Silly me thinking that the wide freq input spec I read on wall-warts was there just to handle this variation of freq.
And to think it has gotten smarter "without a brain".
Ben
* I am just trying to catch up what I seem to have missed. The above is all in good humor. No offense intended or taken.
Message Edited by Ben on 08-03-2009 12:56 PM
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Solution for "Error while trying to synchronize Audio and MIDI" and "System Overload" messages

Article for those who hate Logic error windows
Seen in Logic Pro 9.1.7 on Mac OS X Lion 10.7.4
and Logic Pro 9.0.0 on Mac OS X Snow Leopard 10.6.5
Logic Pro:
System Overload.
The audio engine was not able to process all required data in time.
(-10011)
Error while trying to synchronize Audio and MIDI.
Sample Rate xxxxx recognized.
Check conflict between Logic Pro and external device.
The search in the help given as follows: overload occurs when you use a lot of tracks and a lot of effects on them, and the synchronization is lost when the selected MIDI track for recording or playback. Yes, this is all that is written in the resources. And here are useful tips that have been found:
The Bounce function allows the entire instrument track to be recorded as an audio file. This bounced audio file can then be used (as an audio region) on a standard audio track, allowing you to reassign the available processing power for further software instrument tracks. For more details, see "Bouncing Your Project."
You can also make use of the Freeze function to capture the output of a software instrument track, again saving processing power. For details, see "Freezing Tracks in the Arrange Area."
These tips - about the timing. About overload - there are no tips, except as "reducing the number of plug-ins" and "increasing latency". Zero useful tips - I got two errors in the test project with a blank audio track with no effects, MIDI drums and standard synthesizer, it was no aux buses, and the entire project was only a single plugin in the master track.
Here is the configuration of my computer:
iMac12, 2
CPU: Intel Core i5 3,1 GHz
Memory: 4 GB
And here's a project that almost immediately stops Logic, all instruments and plug-ins with the init-patch, ie not the most demanding settings:
It's sad.
When this happened the first time, I could start the project only if the empty audio track has been selected, a track specially designed so that you can at least start the project. Then, this problem has evaporated along with the changing conditions of work and I forgot about it until the last case.
I was looking for the cause of the problem in the console and the system monitor for two days, and finally I found that Logic ping to the network frequently. I remembered the exact time of occurrence of the problem, and system logs revealed that the problems began immediately, as soon as I deactivate the service of the Internet.
Solution: enable the Internet, or add a new network service on a computer with no Internet. I just created the Ethernet connection to the ip address 1.0.0.0
Logic immediately began to sing.

Hi gabaghoul
Yes, it worked for me on four different OS and Logic versions (10.6 - 10.8 and 9.0 - 9.1.6)
It does not work in some cases, hard enough to tell in which one, but you can try, it very easy: go to the net settings and create new Ethernet connection to the ip address 1.0.0.0 and connect LAN cable to the port.
Also you can try to figure out what happens in your system while Logic error occured - fot that you just start Console and search "logicpro"
Pay attention to repetitive events in a console and events with suitable timing, not so far from error
The problem may be related to the GUI or system memory, sometimes turning off Safari (or Chrome, others browsers) might help.
Message was edited by: spred

Please I just got an iPad 3 and it keeps restarting itself. How do I stop this. Done hard reset and system reset.

Please I just got an iPad 3 and it keeps restarting itself. How do I stop this. Done hard reset and system reset.

iTunes: Restoring iOS software
You will probably need to restore using Recovery Mode.
iPad: Unable to update or restore
Recovery Mode Instructions
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
Use iTunes to restore iPad.

What are PSI accesed teckets and system generated ticktes?

helllo friends,
i am srinu.
I have a doubt that what are PSI accessed tickets and system generated tickets.Plz let me know.
and also send me the doc about Bex browser and wad and navigation paths.
and some faqs for interviews.
My mail id is [email protected]
wiating for u r reply.
bye

hello Vasu ,
REGARDING PSI : In organizations where SAP R/3 is the standard ERP system, PSI allows project managers to benefit from PS8's power and flexibility, while continuing to disseminate project data through the SAP R/3 system. With PSI, project managers using both PS8 and SAP R/3 can now easily and accurately share information between the two systems. Essentially, PSI translates data from one application into the appropriate context in the other application, allowing both PS8 and SAP R/3 users to manage the same information in different ways. While the relationship between corresponding fields in PS8 and the Project System module of SAP R/3 is predefined, PSI allows you to easily customize the specific selection of data to be transferred between the applications.
REGARDING SYSTEM GENE.... iTS ALREADY BEEN DISCUSSED
list of some functional modules FOR CURRENCY TRANSL;ATYIO ARE
AIB5_GET_CURR_CONV_PARAMETERS
BAPI_CURRENCY_CONV_TO_EXTERNAL Conversion of Currency Amounts into External Data Format
BAPI_CURRENCY_CONV_TO_EXTERN_9 Conversion of Currency Amounts into External Data Format
BAPI_CURRENCY_CONV_TO_INTERNAL Conversion of Currency Amounts into Internal Data Format
BAPI_CURRENCY_CONV_TO_INTERN_9 Conversion of Currency Amounts into Internal Data Format
hOPE THIS HELPS YOU .
GOOD LUCK!

LR3 crashes on opening and system hangs

Hi- I just got LR3.
I kept my Lightroom catalogues on an external drive.
First time I opened LR3 I linked to catalogue and when it was about 75% through upgrading, system froze, got grey overlay on screen and message to restart computer - but all I could do was to cut the power.
I reapired permissions, moved catalogues to mac in 'pictures' and tried again.
I managed to open a catalogue, looked at a picture & then it crashed.
Optimized LR2 catalogues etc
reinstalled etc.
Now all I get is the LR3 logo and system crashes immediately.
Help - rather annoyed that I've just spent £78 for this.
The LR2 upgrade when I had it worked flawlessly.
Others seem to be having the crash further on - I can't even look at catalogues now.
Update: just repaired permissions and am getting:
ACL: found but not expected for many strings - dont know hat t means

I have also had this thread on Canon Forum and Lightroom Forum where I followed the path you suggested.
After various solutions including setting up a clean user account, it was suggested (on Lighroom forum) that I try and open LR3 in 32 bit - which I did and it worked.
I then looked at LR2 which had been working as I noticed a comment that it too was 64 bit - but I had been running it in 32 bit.
I changed LR2 to 64 bit and it also crashed in exactly the same way - so It appears that for LR2 , on installing, the default was 32 bit and for LR3 the default was 64 bit.
Looking on the system requirements for LR3 it says that I ned at least 1G ram - but I have 3G! However, other comments are that LR3 needs 4G to work properly.
Many thanks for all your help - and I hope this thread helps others.
The error message below was what I kept getting every time I tried to load LR3 - the screen froze and I could do nothing but cut the power.

Locked SYS and SYSTEM user

DB version: 11.2.0.2
OS : Solaris 10
In our production DBs , I've noticed that both SYS and SYSTEM users are locked
$ sqlplus / as sysdba
SQL*Plus: Release 11.2.0.2.0 Production on Thu Jan 19 14:21:34 2012
Copyright (c) 1982, 2010, Oracle. All rights reserved.
Connected to:
Oracle Database 11g Enterprise Edition Release 11.2.0.2.0 - 64bit Production
With the Partitioning option
SQL> select username, account_status from dba_users where username like 'SYS%';
USERNAME                       ACCOUNT_STATUS
SYSTEM                         LOCKED
SYS                            LOCKED1. How can I log in to SYS account despite being locked. Is it because i logged in through external authentication?
2. Is locking the SYS user a standard practise ? If so, why ?

Hi;
1. How can I log in to SYS account despite being locked. Is it because i logged in through external authentication?set ORACLE_HOME, ORACLE_SID than
sqlplus "/as sysdba"
alter user xx account unlock;
2. Is locking the SYS user a standard practise ? If so, why ?
SYS and SYSTEM are default users, created with the creation of the database. Although they have much power - as they are granted the DBA role - they're still ordinary users. Because SYS owns the data dictionary, (s)he is considered a bit more special than SYSTEM. But SYS has the SYSDBA privilege which SYSTEM doesn't. This makes it possible for SYS to become a very very powerful user. This is the case when (s)he connects as sys/password as SYSDBA or / as sysdba. The as sysdba phrase is a request to aqcuire the privileges associated wht the single SYSDBA system privileges (see here).
Source:
http://www.adp-gmbh.ch/ora/misc/sys_system_internal.html
Regard
Helios

Can an old iMac G3 drive running system 10.2.8 and system 9 be mounted in the secondary drive bay of a G4 800 Mhz running 10.4.11 and boot from the 10.2.8?

I've done this and the G4 800 Mhz boots up from system 9 on the old iMac G3 just fine, but when I boot up from its system 10.2.8, it runs for only 5 minutes or so and the grey screen comes down telling me to re-boot. I've run Norton on the system 9 disk and system 10 disk utilities on the system 10 disk of the old iMac G3 and all is fine with it. Is there some incompatibilities with running the old iMac G3 230 Mhz from the G4 800 Mhz that causes this to happen? I can access all my old files on the iMac G3 when I boot up with extensions off (holding down the shift key when I boot up), but I would like to be able to use the USB functions when I boot it up.

It sounds like you have a Power Mac G4 Quicksilver 2002, and according to the program Mactracker, it should be able to run on the OS 9 and the OS 10.2.8.
I don't know which version of Norton (Utilities?) you ran on the old iMac drive, but I suspect that might be the problem. This is from the iMac Tray Loading Service Source Manual:
HFS Plus Formatted Drives
The hard drive in the iMac is formatted with HFS Plus (also referred to as Mac OS Extended format). It is important to note that Norton Utilities version 3.5 is not compatible with HFS Plus (or Mac OS Extended format), and in fact, can destroy data on the hard drive.
Norton Utilities version 3.5.3 or 3.5.2 will not attempt to repair a drive formatted with Mac OS Extended format and versions 3.5.1 and earlier cannot recognize that a hard drive is in Mac OS Extended format and can result in hard drive corruption and loss of all data on the drive.
Note: When diagnosing hard drive problems, it is important to verify whether or not the customer may have used the wrong disk repair software for their drive before assuming that the problem is hardware related.
If you experience problems with a hard drive that has been formatted with HFS+, Apple Computer recommends using Disk First Aid 8.2 (which is included on the system software CD that ships with the iMac). Disk First Aid 8.2 can be used to recover data that may have been deleted by Norton Utilities. (See the Symantec Web site at NO LONGER A VALID LINK-REMOVED FROM ARTICLE for more information on Norton Utilities and Mac OS Extended format.)
Some other disk utility and disk locking programs are incompatible with Mac OS Extended format. Before you attempt to use a disk utility or disk locking program, make sure the version you have is compatible with Mac OS Extended format. Check the documentation that came with the program or contact the manufacturer or the vendor that supplied the program.
Use the Get Info command in System 8.1 to determine how a hard drive has been formatted. Drives formatted with HFS will appear as “Mac OS Standard”, while drives formatted with HFS+ will appear as “Mac OS Extended.”
I hope some of this helps.
Good luck.

Unit testing and system integration testing for crystal report

Hi gurus,
I am creating crystal report by oracle procedure, will you please tell me how to do unit testing and system integration testing? appreciate very much.

The focus of this forum is report design. The actual testing of reports would be subject to your own internal policies and procedures.
Jason

Hi i upgrade from lion to mountain lion to day on my mini mac,Since the upgrade i am getting no sound through my HDMI cable which was working fine on lion Checked the midi audio settings and system preferences to out on HDMi nothing no sound whats so ever

Hi i upgraded from lion to mountain lion to day on my mini mac,Since the upgrade i am no longer getting sound through my HDMI cable which was working fine on lion Checked the midi audio settings and system preferences to out on HDMi nothing no sound whats so ever.Any one any ideas?
I use a samsung TV for my monitor via HDMI.Tried all the system Audi setting nothing .Head phone and internal speakers are fine.

Similar issue; Audio was working fine on Lion, now not on Mountain Lion. Have a Macbook Pro early 2011 with AMD Radeon HD 6750M, connected by thunderbolt through a Lacie LBD to a mini-displayport to HDMI adapter (n.b. same problem when not going through the LBD) to a Pioneer VSX 521 AV receiver. For me when I go into audio Midi settings all the volume sliders for the displayport device are greyed out and at zero. But when I click 'configure speakers', it's able to send out the test signals to each speaker. Part of the problem could be that I'm not getting the option to put out 6channel sound, only 2 or 8 channel. Since my system is Dolby 5.1, and I only have 6 speakers, I would have expected the 6ch option to be available. But I imagine there's more to it than that. Elsewhere someone has suggested playing with Remote Interactive over HD on an Onkyo device; I'll see if there's something similar on the Pioneer that can be changed. Any other suggestions welcome.

Peak Power and System power

Similar Messages

Maybe you are looking for