Pendrive not detecting

i have purchased and usb flash drive last 15 days ago from Grant road and it was working properly but all of a sudden it is not showing on my laptop & in disk management its showing no Media pls help me out...

Subani,
You will want to try the pen drive on another computer to test with.
If the drive is still not detected on any other computer, then it is a bad drive and needs to be replaced.
Let me know what you find.
Thanks.

Similar Messages

Pendrive not detecting and not showing files/folders after injecting pendrive into PC !

sir, tell me where i can solve problem of detecting of FLASH DRIVE USB3.0 of model no:v210w that have been purchased from nagpur and currently not detecting and may have so many VIRUSES in that PENdrive. suggest service center to retieve data of PENDRIVE

johnboy922,
Which region did you call into The call center for North and South America is here in Stillwater, OK. While there are some varied accents around here from southern to northern, this OKIE has never had any trouble understanding them.
Daniel

[Solved]Usb Pendrive not detected

Hello, I have a xfce4 desktop and when i insert my flashdrive its not detected in thunar.
I have ticked the options to "mount removable device when inserted" and "mount removable drivers when hot-plugged".
What do I have to do to see my pendrive in Thunar!.
Thanks for reading
Last edited by Jean3799 (2014-06-24 06:00:36)

Make sure gvfs is installed.
sudo pacman -S gvfs
Read in the wiki here and here.

Hp 16 gb pendrive not detected in car stereo system.

hi sir,
i have purchase hp pendrive 16 gb it is working in computer but not detected by the car stereo system please provide the solution.

There could be a couple of reasons why its not working for your car stereo.
Look up the manual for your stereo. Several have a size limit as to what they will accept.
Example: It will read up to an 8 GB drive.
Also make sure you have the right music file type it will read.
Usually, Stereos will read FAT32 and not NTFS. Make sure you have it formated correctly.
Worst case scenario I have seen is that some model stereos will not read every brand USB drive.
The manufacturer may have a list of approved drives.
Hope it helps.

Seagate Hard Drives not detected by the Windows 7 installer

I've spent hours on this trying every conceivable reason, so I apologize in advance for the length on this post.
I connected a Seagate 320GB 7200.10 hard drive to a P35 chipset system and attempted to install Windows 7 RTM onto it. The installer got to the part of detecting hard drives, but could not detect this drive. Native SATA mode was enabled, and AHCI was enabled.
I disabled Native SATA mode, then after that failed I also tried disabling AHCI by setting the controller to IDE mode. Still, the Windows 7 installer refused to detect the drive.
I replaced both the SATA & power cables, verified the drives are detected by the AHCI firmware and the BIOS, and I even tried different motherboard SATA ports to no effect. I took a second , identical Seagate 320GB SATA hard drive, this time pre-formatted it inside Windows 7 RC using NTFS defaults, and again (with and without AHCI and Native SATA mode) Windows 7 will not see this hard drive either!
I even downloaded the AHCI preinstall drivers and loaded these using a flash drive. When I did Windows 7 would autodetect the ICH9 driver and I would click Next. Windows 7 would suddenly see the drive, but all options to format or create a partition are grayed out. Clicking the more info button gives me this error message:
"Windows cannot be installed to this disk. This computer hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu."
I used the AHCI preinstall drivers specific for the motherboard (Vista 64) and I also tried the AHCI preinstall drivers from Intel for Windows 7 RC 64. As of this writing Intel has not released official Windows 7 RTM Intel Matrix Storage Manager drivers.
In frustration I installed a SSD (with AHCI and Native SATA mode enabled) and suddenly Windows 7 detects the SSD without needing to load any driver (as would be expected, since Vista and 7 include Intel Storage Manager drivers by default already). I installed Windows 7 RTM 64bit onto the SSD without issue.
15 minutes later I was at the Windows 7 desktop, and Windows 7 was showing the Seagate 320GB hard drive under "My Computer" as normal. I could even use the Seagate hard drive as normal as if nothing was wrong. For kicks I launched the Windows 7 installer inside Windows 7, but as you can see below it still refused to see the drive, despite the drive being shown under My Computer:
(Since I can't use thumbnails, here's the direct link: http://i111.photobucket.com/albums/n129/Chanur64/Box/Howpossible.jpg )
Also I should note I previously had Windows 7 Beta installed on an IDE drive in this exact system, and had no problems with it. Windows 7 RTM would allow me to install to an IDE drive and allowed me to install to an SSD, but it cannot see and cannot install onto both Seagate 320GB hard drives. These Seagates are known good drives previously part of a RAID 5 array.
If anyone knows what is going on or has some ideas I've not tried I would love to hear from you and get this figured out. Suffice to say this is not a promising start for Windows 7.
Intel Q6600
Gigabyte GA-EP35-DS4 (ICH9R southbridge)
4GB DDR2-800
2x Seagate 320GB SATA 7200.10
Intel X25-M 80GB
8800GTS 320mb
PC Power & Cooling 750w PSU

I just had to solve the same issue with a Seagate Momentus Thin hard drive (
http://www.seagate.com/www/en-us/products/laptops/slim-laptop-hard-drives/)
Tried several BIOS configuration, AHCI drivers, etc and Windows 7 32bits couldn't detect the drive.
My solution was to boot with a USB pendrive with HirenCD tools (http://www.hiren.info/) and use a partition manager to erase disk contents, create and format a partition.
Windows 7 detected the hard drive for the first time and now is installing, so.. crossing fingers.
Thanks,
Diego
Diego,
Thanks for the information and the link to Hiren.info! I'm creating my bootable flash drive now. I'll report back if I get this to work.
I had this same issue on a Seagate Momentus 7200.2 "laptop" hard drive. I say "lap top" in quotes because it's actually in a desktop (HP Compaq Ultra-slim dc7800). I believe it was an upgrade, so it took me a while to figure out what I was dealing
with until I finally took out the harddrive and checked what company made it!
Thanks everyone!

Pendrive not showing up in desktop

i recently updated to Yosemite, now my pendrive isnt woking in mac, iphone is working fine bt pendrive gets detected in disk utility bt not showing up in the desktop, i did format the pendrive several times from disk utltiy bt it didnt show up in the desktop...from the FINDER on top of the screen, then to preference i did marked on the "external drives" but still not working....
wat to do???

i accidentaly press this solved my problem, actually it didnt so please somebody help me with these curse....

My flash drive is not detecting in boot menu of hp j110tx

when i m trying install windows 8.1 from usb ,my usb drive is not detecting in my laptop envy j110tx boot menu .
But the same pendrive is detecting in my another pc and it contains bootable file and it is lodable too
I searched everywhere but i got nothing ,so please help me
This question was solved.
View Solution.

Hi:
Have you created Windows 8 or 8.1 Installation USB Flash Drive with UEFI?
http://www.eightforums.com/tutorials/2328-uefi-unified-extensible-firmware-interface-install-windows...
http://www.eightforums.com/tutorials/15458-uefi-bootable-usb-flash-drive-create-windows.html
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

IPod Touch, not detected in Windows or iTunes...

First of all, hello to everyone...
i want to say that i read a lot EVERYWHERE about my issue and still i couldnt find a solution...
the problem is easy, i have a 3rd gen ipod touch, OS 4.2.1 now fully working... but, it's not detected in windows or itunes, as simple as that, and as u all have read in lots of other posts...
my ipod is now working because i took it to an apple store and they charged it in a MAC and they had no problem at all. the MAC detected the ipod, with all its content and my ipod's name...
but when i took it home -this has been hapenning since maybe... 5 MONTHS!-, i plug it in my PC and nothing happens...
ok, first of all, my spec... win vista home premium 64 bits, last version of itunes...
i tried ALL the solutions provided in APPLE official support page, and nothing happens... that means:
1- completely uninstall itunes and then reinstalling it... i ALSO FORMATED my entire hard drive twice!!!!
2- tried all USB ports and even an entirely different PC and nothing happened
3- bought 3 different IPOD to USB cables and nothing happened
4- tried setting ipod to restore, that way itunes SOMETIMES detected the ipod but i coulnt restore because of different error codes, so i had to take it several times to apple store to "unblock" it...
the only way it works -detection and charge- is with MAC computers or dock systems such as an iHome my gf has thats the way im charging it now, but otherwise it wont work...
i would really appreciate any help, since idont know what else to do!!
thx in advance!!

HI I was having some other problems getting my itouch to restore because it was not being recognized in itunes and kept erroring out. Now it has finally restored after I updated all kinds of drivers and removed and reinstalled itunes and apple software a million times,(yes this is all after installing itunes 8.1 and paying for an itouch upgrade as well) Now itunes says it cannot do anything with the ipod because it is getting an invalid response from the device. So it won't put anything back on my itouch or even show that I have plugged it in. I emailed tech support, If I find anything out I'll let you know, will you do the same for me?

Fax not detected,Comm error, fax run test is all PASS,

Hi Good Day! Im Using a HP color Laserjet Pro MFP M177fw. The Problem is sending fax messages. I do all the updates you need to installed. but the problem with my hp fax machine is still there specially i still receive a fax not detected issue,comm.error, but when i run the fax test run..the result is all PASS. especially the active tel.line,correcrt port on fax machine,tel line current test,dial tone..all the question and are PASS. The firmware is updated like..20140914. Please help me for this kind of problem. Thank You!

Hi @ali_al , I can help you with the fax not being able to send faxes.
Check these settings on the printer:
Confirm the fax number:
Go to setup, fax setup, advanced setup, confirm fax #.
Turn off error correction:
Go to setup, service, fax service, error correction and turn if off.
Set the fax speed to medium:
Go to setup, fax setup, advanced setup, fax speed and select medium.
Turn off the private receive:
Go to setup, fax setup, advanced setup, private receive. Turn it off.
Test the fax.
I have provided a document with some steps to try to see if that will resolve the issue.
Cannot Send or Receive Faxes.
Please provide the following information so I can assist you better.
What type of connection do you have? (Analogue, DSL, Cable Modem)
Are you using the 2 wire phone cable?
Do you have distinctive ring set up on the line?
Is there any voice mail set up?
Do you have a answering machine? (Where is it connected to?)
Where is the fax cable connected to? (modem, wall jack)
Is there a phone also connected the printer?
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

DVD-Audio and "can not detect sound blaster card" with Audigy2 Va

I recently purchased an "Audigy2 Value" card from an eBay user, because I recently purchased some DVD-Audio discs. I downloaded the Audigy2 drivers from the website, and the Creative MediaSource player. 5. Surround sound worked fine for me, though sometimes the driver would reset to the default 2/2. sound and I would have to re-select 5. sound, which was annoying.
Then I was completely unable to get the MediaSource player to recognise my DVD-Audio discs, and the EAX functionality of the player would never work. The EAX logo never appeared in the player. When I tried installing the MediaSource player from an install disc, I got the message "can not detect sound blaster card". Then I discovered the world of EEPROM problems.
I followed advice from some other threads, including using ScanPCI to get information on the card, which yielded the following result.
When installed on my machine (Asus A7A266 motherboard) the ScanPCI reads:
Vendor 02h Creative Labs
Device 0008h Unknown
Command 0005h (I/O Access, BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 00h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 0002h Unknown
Subsystem Vendor 02h Creative Labs
Address 0 is an I/O Port : 0000A800h
System IRQ 5, INT# A
New Capabilities List Information :
Power Management Capabilities
Supports power state D2
Supports power state D
Current Power State : D0 (Device fully-operational, no power saving)
On another machine (specs unknown, it's a "house pc") I got this (with 3 entries!):
Vendor 02h Creative Labs
Device 0002h EMU0K Audio Chipset (SB Li've!)
Command 0004h (BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 04h, Header Type 80h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 002002h CT4850 SBLi've! Value
Subsystem Vendor 02h Creative Labs
Address 0 is an I/O Port : 00009000h
New Capabilities List Information :
Power Management Capabilities
Current Power State : D0 (Device fully-operational, no power saving)
Vendor 02h Creative Labs
Device 7002h PCI Gameport Joystick
Command 0004h (BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 0h, Header Type 80h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Input, type Other
Subsystem ID 002002h PCI Gameport Joystick
Subsystem Vendor 02h Creative Labs
Address 0 is an I/O Port : 00008800h
New Capabilities List Information :
Power Management Capabilities
Current Power State : D0 (Device fully-operational, no power saving)
Vendor 02h Creative Labs
Device 0008h Unknown
Command 0004h (BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 00h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 0002h PCI Gameport Joystick (Guess Only!)
Subsystem Vendor 02h Creative Labs
Address 0 is an I/O Port : 00008400h
New Capabilities List Information :
Power Management Capabilities
Supports power state D2
Supports power state D
Current Power State : D0 (Device fully-operational, no power saving)
(Just a note: above you can clearly see that it does not say I have an Audigy, it thinks it is a SBLi've. Is this normal? The card IS an Audigy 2, it says so on the card.)
So, I put the card back on my own PC, thinking this has fixed my EEPROM, but I get the same as before. Subsystem ID 0002h. And of course the install software will not detect the card.
I realise that I could go back to using the web drivers, but this still leaves me with MediaSource not recognising the card and not enabling DVD-Audio or EAX, which is why I bought the card in the first place!
I have heard that the VIA chipset is possibly to blame for the EEPROM problems on the Audigy cards, and certainly it seems like it is not permanent, since it gave different information on the other PC. So now I am seriously considering getting a new motherboard.
Do other motherboards cause this same problem? I don't want to buy another board and get the same trouble. All I want is to be able to install my MediaSource and have it recognise my card so I can listen to my DVD-Audio discs.
Cheers,
Russ.

Figured out my problem. Installing the drivers from the web to begin with was a bad idea. They just did not work properly with the card.
The "card not found" problem has gone as well, after installing it in another PC. I am also using the proper install disc now, as the other one I was using turned out to not be for the Audigy 2 value after all, but was an Audigy 2 install disc. That easily explains the "Card not found" error. The differing results from the ScanPCI program are still bizarre, though.
Thanks to all of the people on the forum who posted information in other threads to help me deal with this issue. For now I am sticking with the original drivers from the disc and I am not upgrading.

Hard disk not detected once, but now working?

Hi,
I'm Zak, a bit of techie when it comes to playing with software, or re-assembling computers and whatnot. Unfortunately I've got no clue about some other things.
A bit of quick history on my notebook: The fan has been making terrible noises the last few weeks. Initially I thought it was some dust so I got some duster. A lot of dust came out, so that can only be good, but the noises came back after a few days. After some searching I figured the other logical explanation was probably the hard drive going bad. I'm hesitant to send it back to HP because I use it for all my university work and it would really set me back a few weeks to not have it.
So, a few days ago, I booted up my notebook to a "hard drive not detected" - or very similar - message. There were a few options, for f1-f4, they were system information, and 3 different tests (I think). I ran the tests, each one came back fine, noting that there was no OS installed, or hard disk to boot from. I rebooted because I hadn't quite seen it boot up, and wanted to see if there were any other options. Turns out, it started up fine. I restarted once more and again, it did fine.
Next, I scrambled around, backing up all my data, getting together warranty info, installing the HP Support Assistant, etc. I ran all the tests from the Support Assistant and there were no problems detected. Since then I've just been hibernating the notebook when I stop using it, and I haven't encountered any unusual trouble. It all seems fine, but my warranty expires Dec 7th of this year. Is it safe for me to assume the "hard drive not detected" error was just a single misfire? I've read a lot of threads and FAQs on it and it doesn't sound like something that just happens once and goes away. On the other hand, I've never had to use a warranty so am unsure quite how the process works, and like I said, sending it anywhere would put me back in my work.
For the sake of a full post, I have an HP G62-367DX Notebook, running on Windows 7 64-bit OS, and as far as I know there were no changes made between the error and my prior boot. If there's any other information I can provide, just let me know.
Cheers, thank you very much for any assistance, and good day
This question was solved.
View Solution.

The tests from the Assistant are not as comprehensive or reliable as the full hard drive test in the BIOS....tap F10 as you power up, go in there and find the hard drive test. Run the long form test and see what is says. It is not unusual for hard drive issues to start as intermittent and gradually get more frequent. If your drive passes the long form test you can fairly safely assume it was a one-time gremlin of some sort, but it is still a real good idea to back up. I like the idea of the online backup services and I will name Carbonite only because it is well known and not as an endorsement. There are several more and an external drive is also a good idea.
You cannot put off a reboot forever; you are going to have to confront the issue at some point.

My Iphone 5 is not detected in window 8.1

My Iphone is not detected in windows 8.1, what is the reason?

Camera roll to pc, no portable device anymore

Connected usb driver is not detected in window 8.1

hey .....
HP 250 G3 notebook
connected usb driver is not detected in window 8.1 after update BIOS software ....my current BIOS software version F.22 .... so plsss...fix this problem......

@jeet2113
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

Windows 8 and Server 2012. Not detecting network is a domain.

Hi Guys,
I hope I have posted this to the correct forum.
I have 2 x Windows 8 PCs that do not detect that they are connected to a domain (network location awareness not working). I can join them to the domain but they still don't recognise the network as a domain. Instead they identify it as "private".
Other PCs on the network (Win XP and Win 7) work prefectly, just the windows 8 machines don't work.
Also, when I do join them to domain I also receive this message.
"changing the Primary Domain DNS name of this computer to "" failed. The name will remain xxxx.local. The error was: the specified domain either does not exist or could not be contacted. "
I have tried the following
- DHCP and DNS has being tried both as static and dynamic (can ping DNS server which is the domain controller Windows Server 2012) .
- Updated PC NIC drivers.
- No AV is installed on either server or PC.
- Updated PC to windows 8.1.
- Disabled both server and PC firewalls.
- Check NLA service and all dependent services are running.
- Disabled all adapters on server except for one.
I am really hoping someone can help with this as I would really appreciate it.
Thanks.
Shaun

Hi Guys,
I managed to find a solution to the problem. I noticed that the DNS server zones did not look quite right. The _msdcs zone was missing the subfolders (dc, domains, gc, pdc).
To fix this issue: on the NIC adapter I had to tick the box "register this connection's addresses in DNS" (found under TCP/IP v4 > advanced > DNS tab).
I then had to remove the DNS role, reboot then re-add the role. Problem solved. Hopefully this saves someone else pulling their hair out for an entire day.

Photoshop CC 2014.2.1 not detecting my dedicated GPU

When I open Photoshop, I get the following error message:
"3D features require a minimum of 512MB of vRAM. Photoshop has detected less than that on your system.
Updating the driver of your graphics card may resolve the issue."
I am running a laptop PC with an integrated graphics card (Intel HD4600) and a dedicated Nvidia GTX 675M with 2 GB of vRAM.
I switch between the two adapters with the press of a single button, for power-saving purposes.
I always run at high-performance with the dedicated GPU active when running Photoshop.
I run the latest driver from Nvidia, and in the Nvidia control panel I manually set the preferences for Photoshop to utilize the dedicated GPU. But it still does not detect my main graphics adapter.
I checked the system information in Photoshop and cannot make sense of it. Why would it be unable to detect the GPU when every GPU demanding software I have run so far (a lot) have been able to..
I have checked google and the very forums and found the problem in various forms with no real solution for it so far. Hopefully someone on these forums can help, considering I am paying a monthly fee for the program and the support that comes with it
First part of System Information in case it can be useful:
Adobe Photoshop Version: 2014.2.1 20141014.r.257 2014/10/14:23:59:59 CL 987299 x64
Operating System: Windows 7 64-bit
Version: 6.1 Service Pack 1
System architecture: Intel CPU Family:6, Model:12, Stepping:3 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, AVX, AVX2, HyperThreading
Physical processor count: 4
Logical processor count: 8
Processor speed: 2394 MHz
Built-in memory: 8112 MB
Free memory: 4011 MB
Memory available to Photoshop: 7080 MB
Memory used by Photoshop: 70 %
3D Multitone Printing: Disabled.
Windows 2x UI: Disabled.
Highbeam: Enabled.
Image tile size: 1024K
Image cache levels: 4
Font Preview: Medium
TextComposer: Latin
Display: 1
Display Bounds: top=0, left=0, bottom=1080, right=1920
OpenGL Drawing: Disabled.
OpenGL Allow Old GPUs: Not Detected.
No GPU information available

Thanks for the quick response!
But as mentioned in my initial post, I deactivate the integrated graphics adapter when using Photoshop, or any software that demands decent graphical processing power.
I only have it activated when in power-saving mode. And of course I update to the newest display drivers via the GeForce Experience or through their website.
Point is, I have never had any problems with any software whatsoever in detecting the proper GPU and utilizing it's power. The only software unable to register my dedicated video card is Photoshop.

Pendrive not detecting

Similar Messages

Maybe you are looking for