Phantom of the Ethernet

My wife has been using our PowerBook G4, running 10.3.9 Out of the blue, she can only connect to our home LAN using the built-in Airport. When I check the Network Status, the Built-In Ethernet is completely gone from the Network Status list, even though it is still enabled in Netowrk Port Configurations.
Ran TechTool Deluxe, no hardware problems were found.
Went back to Network Preferences, tried several minor things, still can't figure out why the Built-in Ethernet port is completely missing. Tried Mac Help and search here, but came up empty.
Any ideas what to try next?

...or at least that's what we THOUGHT had been done....checked again and guess what....D'OH!!!!!!! Thanks for helping out the idiot brigade!

Similar Messages

My 2012 Mini OS 10.7.5 cannot see the Ethernet connection to my Actiontec GT701 WG. The Network Preferences says "cable unplugged". The WiFi connection is working fine. Please Thank You

My 2012 Mini OS 10.7.5 cannot see the Ethernet connection to my Actiontec GT701 WG. The Network Preferences says "cable unplugged". The WiFi connection is working fine. Please Thank You

Never mind, problem solved. When I retunred to the Network tab the message had changed to "connected, no IP address" so I got that from the WiFi tab and configured the Ethernet manually. Have a nice day @:-)#

I am unable to set up my new Time Capsule with my BT Home Hub - every time i connect the ethernet cable from Wan port to Home Hub, the internet signal drops

Hi there -
I've just purchased a new Time Capsule, and would like to set up a small home network with my Laptop, iMac and wireless printer. I'm following the first steps, but as soon as I connect an ethernet cable between the WAN port of the TC and the ethernet port of the HH, my BT internet connection drops out and I have to restart the HH. Upon which point it drops out again. The airport utility can see my TC, and gets as far as me typing in the new network name and setting up a password, but then it can't quite get through to the next stage. All the time it's just flashing amber.
Please help!

Setup the TC in bridge mode before you cannot it to the HH.
Simply do the setup fully in isolation. And do it by ethernet.
Setup wireless to create a wireless network.
You can use either same SSID =Wireless name as the HH .. same security same password.
Or use a different name and setup.. totally up to you.
Update the TC and then plug it into the HH by ethernet.

Can I activate the ethernet ports (routing) of Time Capsule "joining" an existing non-Apple wireless network ?

Hello,
I have a DSL modem that is also a WIFI router as my main WIFI network from room A. In room B, I have a TC wirelessly joining the existing WIFI network (not creating a new one). That works fine, I have one SSID, and I can wirelessly access the TC disks and backup my Mac on my TC.
Now, I would like to connect a wired device (with on WIFI) to the ethernet port of my TC. Unfortunately, the ethernet ports of the TC don't seem to be "activated" as they do not have internet on them.
More precisely, I'd like to connect a GE Cordless Skype Phone Model# 31591 (http://www.gephones.com/products/skype/dect-6-0-expandable-digital-cordless-phon e-with-skypetm.html) that connects to a router via Ethernet. I'm aware that I could simply connect it to the DLS router, but that's not what I want... Is there any way to activate the ethernet ports of the TC while in "join" mode ? Or do I really have to buy a Airport Express to create my main network and then extend it ?!?

Thanks, the reason why I asked again, is because you told me to start another thread with the specifics of the device I want to connect, so I did
Not a big deal, and it is easy to become confused.....but to be clear about this
Your question.....
is there a way I can connect my Bluray player to the TC ?
My Answer.....
Please start a new post for that. Tell us the make and model number of the player and whether you plan to connect using wireless or Ethernet.
so I tried to creat the main WIFI network with a first-generation Airport Express M9470LL/A (802.11b/g, no "draft N" or "n" support) and the TC wouldn't extend it either, is it too old/not supported
Unfortunately, the "extend" setup will only work with "n" devices. The older Express does not have a setting to "Allow this network to be extended", so the Time Capsule cannot pick up the signal.
I'm not sure what else to suggest other than what I already have. I'm assuming that you do not want to buy another new Airport Express.

I have just got an Airport time Capsule for back up how do I do it? Do I put the ethernet cable into the back of my sky hub because when I do that the amber light on my Time Capsule flashes amber. Please talk in simple terms as I am a

I have just got an Apple Airport time capsule to back up my one year old iMac......how do I do it? I have tried putting an ethernet cable into the time capsule and to my sky hub, all I get is a flashing amber light, can anyone help I am a silver surfer not used to Apple products, but love them, plus I don't understand half of the jargon....HELP please

Apple's Setup Guide for the Time Capsule is pretty simple and clear for most users, and you don't indicate at what point or step that you are getting stuck.
So, please go to page 8 in your Setup Guide to review the topic of Plugging In Your AirPort Time Capsule.
The Sky hub will likely have 4 Ethernet <--> ports on the back of the device. Pick any one that you want and connect one end of the Ethernet cable to the port that you choose.
Then, connect the other end of the Ethernet cable to the WAN (circle of dots) port as shown in the Setup Guide.
Continuing with the instructions on page 8 of the Setup Guide, power up the Time Capsule by connecting the power cord from the back of the Time Capsule to a wall AC jack.
Note that the instructions indicate that the indicator light will be solid amber during startup, and it will change to blinking amber during the setup. The light will remain blinking amber until you have configured the Time Capsule at which time the light will turn green.
Next, go to page 12 of the Setup Guide to see the information to Use your Mac or iOS device to set up your AirPort Time Capsule.
You indicated in your tag line that you were using OS X Mountain Lion (10.8.3), and since that will exceed the minimum requirement of a Mac using OS X (10.7.5) as noted in the guide, you can use your Mac to set up the Time Capsule.
Continuing with the instructions on page 12 of the Setup Guide......
1. Open AirPort Utility on your Mac. It is located as follows: Finder (the smiley face on the dock) > Applications > Utilities > AirPort Utility
2. Select your AirPort Time Capsule and click Continue. You won't be able to do this, but read further......If you do not see the AirPort Time Capsule that you want to configure, choose it from the WiFi status menu in the menu bar, at the top of the screen.
So, clicking on the WiFi icon will yield a small window that looks like this:
The example below shows an AirPort Extreme. You will see Time Capsule on your screen. Click on Time Capsule.
When you click on Time Capsule, that will get the setup wizard going. it will take a minute to analyze the network, then display a screen that looks similar to the illustration below, except that you will see a picture of a Time Capsule on your screen
3. Continuing with the Setup Guide.......Follow the onscreen prompts to create a new network
Network Name...........Type in a simple name that you want to call your network. Do not use the suggested name.
Base Station Name....Type in a simple name that you want to call the Time Capsule. Mine is TC, for example.
Password...................Type in a password that will be used for both the network and the Time Capsule. Write that down.
Verify..........................Type in the password again to Verify
Click Next
The setup wizard will configure everything for you. When you see the message of Setup Complete, click Done.
The Time Capsule is now set up and it will display a green light.

Can I use the Airport Express to connect to a Linksys Wireless Network and then use the Ethernet port on the Airport for a wired connection to a device for internet access? Would I be able to then also use that Ethernet pt to a Ntwk Hub for more wired c

Thanks for the help. Looked but not clear on what I am trying to do as being possible. Can I use an Airport Express to connect wireless to a Linksys Wireless Router, such that I can then use the Ethernet ports on the Airport to either connected to a PC wired, or even use a hub off the Airport Express to allow multiple wired connections to it?
I am not looking to have the Airport Express extend my wireless network, just connect to it and provide me wired connections in a different location from where my Linksys Route is located. Would prefer to replace Linksys with all Apple, but just not possible financially yet. Thanks for the help.

If the AirPort Express Base Station (AX) is an 802.11n model, then yes, you can reconfigure it as a wireless Ethernet bridge. In this configuration, the AX would join the wireless network provided by the Linksys router and its Ethernet port would be enabled for either a single wired device or for an Ethernet hub or switch for multiple devices.

How do I connect my MacBook Pro to my Network using Ethernet as there is nowhere to plug the Ethernet cable in? What adaptor do I need? then how do I keep everything, docs and emails, synchronised daily?

I have just bought a MacBook Pro and want to synchronise all data (excluding photos and music) and emails currently on my desktop iMac.
First question, how to I plug in an Ethernet cable to the MacBook so that the two can be connected to the same network via the ethernet? Step one of the Apple setup wizard has me flummoxed!
Second question, once I have that sorted, how do I keep the two devices synchronised (data files and email) and how do I keep the email synchronised to my iPhone?
Help!

Direct you to the proper forum for MacBook :
MacBook Series Forumshttps://discussions.apple.com/community/notebooks?view=discussions
http://www.apple.com/support/macbookpro
Mac OS X Forum
https://discussions.apple.com/community/mac_os?view=discussions
This forum deals with a desktop/tower 65lb Mac Pro
http://www.apple.com/support/macpro

Can I see the Ethernet signal connected to my PC on RJ-45 connector (electric form)?

Hi,
I start working on a project that needs me to know the electric characterisitics of an Ethernet signal in a specific network, and it is illegal to connect any device directly to the network (except for PC). So I was thinking can I use Labview to get this signal from RJ-45 connector and see it??
I'd appreciate any comments or thoughts that help me.
Thanks in advance,
Zeina

Dear Zeina
As Dennis mentioned previously you need an instrument to analyze the signal from the Ethernet. You can then use LabVIEW to analyze the signal, once you have connected the relevant pins of the ethernet cable you wish to view the signal through.
Using NI-VISA you can communicate to a third party device over the ethernet link and acquire a signal in LabVIEW or Measurement and Automation Explorer (MAX). The is a useful link below:
http://zone.ni.com/devzone/cda/tut/p/id/7374
Many thanks for using the NI forums and I look forward to your reply.
Kind regards
David
Applications Engineer
National Instruments UK

Cant set up Airport Express. Trying to create a new wifi at my apartment complex that has provided wifi. I plug the ethernet into the wall in my room and I cannot connect to the wifi.. help please

to help me set up my airport express to my public wifi at my apartment complex

I am a bit lost if you have a public wifi why are you using ethernet into the wall.. is the ethernet just for your apartment.
The Express can work as a wireless bridge only to the public Wifi nothing else.. it cannot extend wireless.. so the express would need to plug into another router for you to get more than one single connection to the building.
Also does your public wifi have a login page . .. because that will then make life much harder.

Is it possible to connect an HP LaserJet P4015n printer to a computer via the ethernet ports?

My usb port on my Laserjet P4015n no longer works and I am unable to connect this printer to my network router because it's in a different room. Is it possible to connect an HP LaserJet P4015n printer to a computer via the ethernet ports? Of so, how would I go about making this connection? Will I need to install ethernet drivers for this to work?
Thanks,
Greg

This seems to be a commercial product. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
You can find the Commercial Laserjet board here:
http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

The ethernet port on the thunderbolt display is not working

The ethernet is working when the cable is connected directly to my mac laptop but when connected the thunderbolt display there is no connection. Is there some type of set up for the ethernet connection or can this port just be broken?
Thanks for the help!

Afterthought on an older post: it isn't immediately clear that the Ethernet port on the Thunderbolt Display works through the "Display Ethernet" interface, rather than through the "Thunderbolt Ethernet" interface. The latter was already present in the list of network interfaces in Network Preferences, while the former had to be added via the + button --- at least that was the case when I installed the TB display to work with my 15-inch MacBook Pro Retina this week.
The AppleCare rep didn't know the difference either and agreed with me that it was puzzling that using the Thunderbolt Ethernet adapter on the Thunderbolt port of the display did work, wheras using the Ethernet port directly didn't (even though there were lights flashing on the Ethernet port of that other computer I tried to connect to in Internet Sharing mode). Close reading of the above posts made me go look for that mysterious "Display Ethernet" interface... thank you Clinton!

Why does my Airport Express say "self assigned IP address"? No IP address for the ethernet, and it is not connecting to my cable router any longer...

Why does my Airport Express say "self assigned IP address"? No IP address for the ethernet, and it is not connecting to my cable router any longer...

Some cable providers.....like mine, a well known company......seem to take anywhere from a few moments to sometimes up to 30 minutes to allow their equipment back at the cable company to fully reset and issue a new fresh connection.
So, it would not hurt to leave things powered down for 15-20 minutes or more when you perform the reset that John Galt suggests.

I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this

I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this? I gace tried the System Preferences -> Sharing, shared internet to Ethernet, but can't se ethe device on Finder

Djembe wrote:
UEFI (unified extensible firmware interface) boot requires Global unique identifier Partition Table (GPT) as opposed to the older Master Boot Record (MBR). If your existing drive is formatted in MBR, you will need to adjust BIOS settings to enable legacy boot in order for it to work properly.
Is there a performance difference between GPT and MBR? If GPT is better, I do not mind formatting the drive with it.
5. No special drivers are needed.
Thanks. What about the thunderbolt port?
7. I think Lenovo estimates 6 hours.
Lenovo says 6 hours with the 6-cell battery on its website.
BrendaEM wrote:
Hi,
There was a serious BIOS/UEFI problem with that SSD . Perhaps this thread will save you some headaches. Someone is recomending shutting off Rapid Boot in the setup, which would probable mean little with a SSD, anyway.
I read through this, and it looks like the problem was fixed in a BIOS update, which I plan to do. However, it also seems like Intel Rapid Start is not even worth it in the first place, as sleep consumes almost no power at all.
W540: i7-4700mq, K2100m, 8 GB DDR3L, 512 GB SSD
T510: i7-620m, NVS 3100m, 8 GB DDR3, 512 GB SSD

Can I connect a external hard drive to the TC thru the Ethernet instead of the USB port so it will transfer data faster

I Want to connect the external hard drive so that I can transfer files faster then the USB 2.0. There is a thunderbolt to Ethernet adapter that you can buy I I just want to know if the hard drive can be accessed thru the Ethernet line instead of the USB. I think it will work faster than the USB. But not sure

It won't work.. the thunderbolt to ethernet adapter doesn't work without drivers and the external thunderbolt drive is not now or ever a network drive.
Yes you can plug an ethernet type drive into the TC.. or into anywhere on the network.. it is after all another network drive..
eg Another TC is a network drive.
Seagate or WD make reasonably priced network drives. But they will not have the HFS+ format which the TC does.
You can buy a NAS from any of a whole range of companies.. A NAS is an ethernet connected drive.
See the reviews here to pick a NAS.
http://www.smallnetbuilder.com/nas/nas-charts/view

I have a iMac g4 swivel and it seems that the ethernet port and the optical drive are not working.

Is there any troubleshooting I can try, short of replacing everything?
I really love this version of the iMac and want to use it in place of my eMac for some home business inventory and printing work.
I need the ethernet to work because the printer can only connect that way. It's a great laserjet from HP (1998 version) and it works like a champ.
As for the disc drive... I would love to install office or iwork but as I said nothing seems to mount. I also can't upgrade it to Tiger. It's running Panther and I can live with that I suppose.
I have wondered if I could exchange parts from the eMac (Motherboard, Optical Drive, Hard Drive) since its bulkyness takes up so much room.
Any ideas?
Thanks
And yes I have a modern macbook pro as well.

You can use the dvd drive on your macbook via target disk mode.
"Installing OS X 10.4 'Tiger' on DVD-Challenged Macs Using FireWire Target Disk Mode"
http://lowendmac.com/misc/06/0710.html
1) Do you have a router? Do you communicate to the internet via wifi?
connect the printer to a router with an ethernet port. This will be an input eithernet port.
You may need to change ip addresses on your printer or on your network.
2) usb to ethernet dongle
Apple USB EN Adapter Network adapter - Hi-Speed USB
http://www.google.com/products/catalog?oe=utf-8&rls=org.mozilla:en-US:unofficial &client=firefox-a&q=usb+to+ethernet+dongle&um=1&ie=UTF-8&tbm=shop&cid=1255179391 6678370799&sa=X&ei=L7xdTsDTGsXz0gHdvazcAg&ved=0CF8Q8wIwAw
verify that the dongle will work on your machine. Any drivers needed?
3) You can firewire to for TCP/IP ( ethernet) to comunicate between macs. Connect your printer to your macbook. Use firewire to communicate between macs. Enable printer sharing.

Phantom of the Ethernet

Similar Messages

Maybe you are looking for