Philips TV 9000 serie stops streaming

I have a philips tv 9000, qnap 210, twonky and e2000.
When i using my e2000( wireless/cable) the tv stops playing the vids after 5 min.
When i using un very old smc router there's no problem.
Does anybody recongize the problem?

Do the following steps:
# Open up the browser and on the address bar type 192.168.1.1 that will open up the Router setup page.
# Lower the MTU (Maximum Transmission Unit) from 1500 to 1492 or less (usually found on your router's main/ basic setup page)
#Adjust the following advanced wireless settings:
~~ Lower the beacon interval from 100 to 70
~~ Lower the fragmentation threshold from 2346 to 2306
~~ Lower the RTS threshold from 2347 to 2307

Similar Messages

  • AirTunes stops streaming after each song but iTunes shows it playing

    I've read through a lot of posts and either people are having the same issue just describing them differently or I'm seeing an entirely different issue.
    My setup is Windows Vista running iTunes 8, Airport Express and an iPod Touch running the Remote app. I just bought it all yesterday and did all the firmware and software updates it asked me to when setting it all up.
    I had it setup wirelessly and working -- the remote controlled iTunes which send audio to my AE and it worked beautifully. Then I realized the music stopped, I went to check and iTunes still showed the music playing, but no sound was coming out of the remote speakers. If I change the speaker output to computer then back to the remote speakers it starts playing again.
    I've disabled wireless on the AE and put a long wire across to rule out wirless interference or problems. I've disabled the Windows Vista firewall as well.
    I've tested both from the remote and from using iTunes directly. So I've ruled out the Remote App from the equation (I think). I say that, because first thing this morning I ran using just iTunes and it worked for 15 straight songs. I used the remote to change albums and start another and after the first song played it went silent. I noticed in iTunes a playlist called "Remote" comes up so I was thinking the Remote was causing it. I switched over to my library local on iTunes again removing the remote and it keeps happening anyway. So I'm not sure if by using the remote I put it in this "state" or if it's really not the Remotes problem.
    OK, so once it happens, it stops streaming after very single song however iTunes still shows it's playing fine. To fix, turn the speaker off then on again or switch to computer then back to remote again. It works doing this via the Remote App or on iTunes directly.
    This is FRUSTRATING! I spent a lot of money on the iPod, AE and getting a cheap stereo receiver/amp to feed my in-house speakers and now it's pretty much not even useful.
    Suggestions? Help? Anything?
    Message was edited by: TimLindner

    I wanted to post a follow-up. I solved my own issue after starting to rule out every possible cause.
    I have a Western Digital networked hard drive (NAS) which houses all of my MP3's. I knew accessing this drive was pretty slow but I've had my MP3's on it and iTunes' library is all coming off this drive. It has worked fine on my computer for years. However, it appears that the lag doesn't play nice with AirTunes.
    I moved my entire iTunes library (about 80 GB) to my local machine's hard drive, rebuilt my library and now it plays flawlessly!
    Just so people know, I've updated firmware on the AirportExpress and the iPod Touch, I have the new version of Remote on the touch and am running iTunes 8 on Windows Vista with its library on the local harddrive. No glitches, pauses, or problems. I ran it for 6 hours during a party over the weekend without flaw.
    -Tim

  • Ask the Experts: Understanding Cisco ASR 9000 Series Aggregation Services Routers Platform Architecture and Packet Forwarding Troubleshooting

    With Xander Thuijs
    Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn how to Cisco ASR 9000 Series Aggregation Services Routers with Cisco expert Xander Thuijs. The Cisco ASR 9000 Series Aggregation Services Routers product family offers a significant added value compared to the prior generations of carrier Ethernet routing offerings. The Cisco ASR 9000 Series is an operationally simple, future-optimized platform using next-generation hardware and software. The ASR 9000 platform family is composed of the Cisco ASR 9010 Router, the Cisco ASR 9006 Router, the Cisco ASR 9922 Router, Cisco ASR 9001 Router and the Cisco ASR 9000v Router.
    This is a continuation of the live Webcast.
    Xander Thuijs is a principal engineer for the Cisco ASR 9000 Series and Cisco IOS-XR product family at Cisco. He is an expert and advisor in many technology areas, including IP routing, WAN, WAN switching, MPLS, multicast, BNG, ISDN, VoIP, Carrier Ethernet, System Architecture, network design and many others. He has more than 20 years of industry experience in carrier Ethernet, carrier routing, and network access technologies. Xander  holds a dual CCIE certification (number 6775) in service provider and voice technologies. He has a master of science degree in electrical engineering from Hogeschool van University in Amsterdam.
    Remember to use the rating system to let Xander know if you have received an adequate response.
    Xander might not be able to answer each question because of the volume expected during this event. Remember that you can continue the conversation on the Service Providers community XR OS And Platforms  shortly after the event. This event lasts through Friday, May 24, 2013. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.
    Webcast  related links:
    Slides
    Webcast  Video Recording
    FAQ

    Is there a Cisco lab available for ASR 9000
    we have "XR4U" stations coming available soon when XR 511 comes alive. The plan is for a downloadable play image like that. In the interim we have 2 demo systems available, and they can be booked via your account manager representative.
    How will MOD160 perform with multiple 9000NVS?
    very well. the mod 160 has 4 NPU's, 2 per bay. So if you have a 4x10 MPA to serve a satellite, you effectively have a single NPU per 20 1Gigs from the satellite. The pps performance will be stellar. However it might be price technically more ideal to connect satellite with a 36x10. Since the MOD-x has native MPA's with 1G also.
         2. Is there a shortcut for a Bundle-EthernetX interface, such as port-channel interface (poX), in Cisco IOS® ?.
    usability enhancement is there, we are trying to push this into a new reasonable release. follow CSCuh04526
         3. What  is the revolutions per minute (RPM) on these hard disk drives (HDDs)  compared to the solid state drives (SDDs)? Will the spinning drives be  slow?
    depends on the type we had avaialble at time of production, you will see different sizes and disks on the RSP2. the rpm of the HD is not so much an issue as much as the buffered writing we used to do in XR. This is fixed up with XR43 where the disk writing performance is much better. the HD/SDD is used for logging storage only (and maybe your pictures) but other then that we're not that concerned with write perf of the HD.
    regards
    xander

  • HT201077 I have windows 8.1 and ios7.  contacts and calendar stopped streaming to my laptop but was ok on ipad and iphone. That problem fixed but now photos stopped streaming to laptop.  Any suggestions

    I have windows 8.1 & ios7.  Contacts & calender stopped streaming to laptop. ok to ipad & iphone.  This was fixed but now photos stopped streaming to laptop again ipad/iphone talk.  All settings seem ok.  Any suggestions?

    Hey pat121,
    I would run through the recommended troubleshooting steps in the following article to see if that alleviates the issue:
    iCloud: My Photo Stream troubleshooting
    http://support.apple.com/kb/TS3989
    Welcome to Apple Support Communities!
    Regards,
    Delgadoh

  • Why does my apple tv constantly stop streaming and become unable to connect to itunes?

    I have a 2nd gen Apple TV, which I bought in Dec'10. Lately, as in the last month, it just stops streaming. It will be streaming content, then all of a sudden, it stops, and bar comes up on the bottom of the screen, showing the length of the video, with a spinning icon on the left, where the play/RW/FF icon usually appear. It never recovers. I'll stop the video, and try playing again, but it will say that "netflix" or "iTunes" etc. is currently not available. It's as if it's getting knocked offline. I check my setting, and the ip address is fine, it is not assigning itself an ip address. My internet is working with no issues at all. I'll try doing a network test but it sits there trying to connect to itunes, then it says it's unable to do so.
    It's becoming more and more frequent. The only thing that works is resetting it, and sometimes even that doesn't work. So, I have to restore it. I've had to restore a couple times in the past month, and I'm resetting almost daily.
    Also, sometimes it just reboots itself for no reason at all. This, too is occuring more and more on a regular basis.
    I have the apple tv plugged right into my Time Capsule via ethernet. The hdmi out is going to an input on my surround sound receiver. I've also bypassed the receiver, just to rule it out. I typically get anywhere from 30-40 mbps when I do a speedtest from my macbook on speedtest.net or speakeasy. I'm mentioning this because my connection is more than sufficient to stream the 720p content the apple tv is limited to. My interenet has gone out in the past, but it's rare. It's not the culprit, since someone is always on line when this happens, so we'd know right away if it was the internet going out. It's always the first thing I check when this happens, even though I'm pretty sure my connection is not the issue. Also, I don't start freaking out, the second it happens. I usually don't look into it until a minute or so after the video has frozen. At that point I usually hit MENU, to escape the current screen, then try playing the content again. That's when it can't do anything, and I'm often forced to reset or reboot.
    I have tried searching for others with this issue, but haven't come across anything. The closest I've seen are situations where people can't stream at all, due to a network issue. Also, it's been getting worse, which makes me wonder if it's a hardware issue. Again, the apple tv is on a wired connection to my Time Capsule, and the ip address is not self assigned, it starts with DHCP, not 169... And, my internet connection is not the issue.
    Any help would be appreciated, and sorry if I repeated myself, I just wanted to make sure I didn't leave anything out.

    I had problems with streaming until I changed the WiFi channel that I was using.  The original one conflicted with my neighbor.  After that, MOST of my streaming problems vanished.  Occasionally, a movie would pause for more buffering and I eventually ran an ethernet cable from the Apple TV to my Apple Extreme (to eliminate the Wifi).  I have not had a single problem since then (except to repair the drywall after running the ethernet from one floor to another).  :-)

  • Apple tv stop streaming when screensaver starts

    When I am listening to Spotify from My iPad through appletv the appletv stop streaming the music when screensaver turn in. It worked before the last update of appletv.

    Try to restart your wireless router.... Do you have issues with connectivity when using netflix or crackle apps on the ATV?

  • How to configure snmp on loopback interface, on vrf TEST, in ASR 9000 series

    Hi there!
    How to configure snmp v2, with community string, for ASR 9000 series, in interface loopback 1, that has vrf TEST
    Regards!

    oh that is somewhat vague, but let me try...
    in order to enable snmp access to an interface in a vrf you need to enable MPP (management plane protection) in that vrf.
    Something like this:
    control-plane
     management-plane
      inband
       interface Loopback100
        allow all
    if you have this and it doesn't work, a config snippet and some debugs (like debug snmp packet) will help to define what to do next.
    regards
    xander

  • IPod Touch 2.2.1 Stopped Streaming Quicktime Clips

    Hello,
    I searched and couldn't find any info on why my iPod Touch 2G stopped streaming quicktime clips from the site drummerworld.com.
    This has not been an issue until recently, and now I just get a strange icon rather than a clip playing. Any info would be great as I visit this site quite often for tips and such.

    [quote]Since it is tied to the OS you are running, you really don't have any control over which version of Quicktime you are running. [/quote]
    Ok, I'm running v 7.6 which is the same as the site.
    Perhaps the site has changed something ? This is strange because it worked for the first few weeks.

  • My Photos have stopped streaming to my pc

    My Photos have stopped streaming to my PC from Iphone 4s & Ipad.  I have IOS 8.1.1 on both  phone & Ipad.  I have iCloud 4 on pC. It was working fine before I upgraded to iCloud 4.
    The photos are streaming between my two apple products just not to my PC.
    Thanks for any help.

    Hi ctmelancon,
    If you are having issues with your Photo Stream, you may find the following articles helpful:
    iCloud: My Photo Stream FAQ
    http://support.apple.com/kb/ht4486
    iCloud: My Photo Stream troubleshooting
    http://support.apple.com/kb/ts3989
    Regards,
    - Brenden

  • TV and Airport EXPRESS stop streaming after update

    I have read all of the posts regarding the Airport Extreme update being the culprit of the slow streaming with the Apple TV, but I have an Airport Express (2 actually) that suddenly stopped streaming after the last batch of updates (iTunes 8 etc.).
    Everything has been working flawlessly - I have all my movies and TV shows on an old Mac that streams to my Apple TV via 2 Airport Express base stations. I have one AE station "hosting" my internet connection, and then the other acting as a WDS remote. Suddenly after the last updates I have no streaming. I have re-set everything, and re-connected my media server to my Apple TV and no luck. My AE's are at the latest firmware 6.3, and Apple TV, iTunes and even OS is all up to date.
    If anyone has any ideas how to fix this I would really appreciate it - it's driving me crazy.
    Thanks in advance.

    Am in the same boat as it where, so will be happy to hear a solution!

  • Oracle9i Database Release 2 Enterprise for HP 9000 Series HP-UX

    Is the "Oracle9i Database Release 2 Enterprise/Standard Edition for HP 9000 Series HP-UX" really
    running only on HP-UX 64 bit. No chance on 32 bit?
    Werner

    Yes. Oracle's current platform strategy is:
    Oracle Platform Roadmap:
    Organizations are deploying Oracle's database, applications, application servers and development tools on a short list of systems that dominate the market. Beginning with the Oracle9i Database, Oracle9i Application Server, and E-Business Suite (Oracle Applications) 11i, the following operating systems will be supported:
    HP Alpha OpenVMS(1)
    HP Tru64 UNIX(2)
    HP-UX(2)
    IBM Linux/3901 & z/Linux(1)
    IBM OS/3901 & z/OS(1)
    IBM RS/6000 AIX(2)
    Intel Based Server LINUX
    Microsoft Windows 2000
    Microsoft Windows NT for Intel
    Solaris Operating System (SPARC)
    (1) - For Oracle9i Database ONLY
    (2) - 64-bit ONLY
    Several Microsoft Windows clients are supported, including Microsoft Windows XP.
    Oracle will continue to support the Oracle8i Database and current versions of all other products throughout their support life cycle on the operating systems where they were released, including 32-bit versions of Oracle running on HP-UX and IBM RS/6000 AIX systems. Additionally, Oracle will continue to provide 32-bit client library support through the life of the Oracle9i Database. In keeping with our normal product support life cycle process, customers will be informed of status changes to individual product versions currently supported.

  • Both of my ATV1's stopped streaming today!

    Both of my ATV1's stopped streaming today! I can set them up for streaming to any of several Macs in the house, but I can't stream any content!
    The user interface is very sluggish on both of them. Every time I try to scroll down to "Shared Movies" it jumps back to the top of the menu before it recognizes that I have hit the select button. I believe this is the reason I cannot stream content--one time I was able to stream music but that was after much trial and error, and I have not been able to repeat it since that one time.
    I have one ATV3 which still seems to work fine.
    I am using hardwired Ethernet, not Wifi.
    Anyone else seeing this?

    There is a fault with iTunes and apple tv 1
    See this thread
    https://discussions.apple.com/thread/6099057?start=165&tstart=0
    Report it to apple

  • How to stop streaming

    I'm developing a Dashboard widget that plays an internet radio stream using the Flip4Mac .wma codec.
    When i use the javascript API and call SetURL and Play() it plays fine. When I call Stop() it stops playing, but it doesn't stop streaming. It keeps streaming even if I try to use SetURL with an empty url, "about:blank" and other gibberish.
    Actually, even reloading the widget doesn't help - it keeps streaming. Closing the widget seems to do the trick after a few seconds.
    I can't really release this widget without a solution, so any solutions or suggestions are welcome!

    artmar1 wrote:
    I want to turn off streaming on one ATV.
    If it is a primary library that you no longer wish to stream, select 'Show only the synced items on my Apple tv' from the summary tab in itunes when the Apple tv is selected in the device menu.
    If it is a secondary library ctrl-click/right-click on the Apple tv in the device list and choose 'turn off streaming' from the contextual menu that appears.
    (Please excuse my unsupported nomenclature)
    Message was edited by: Winston Churchill

  • How to stop streaming to @tv...

    Ok I synced about 140G on my ATV. I moved the thing upstairs and wanted to sync more so I set up streaming overnite to sync the new movies. Now I want to stop streaming and just watch what I have synced. How the heck do I do that? No internet upstairs so plugging a line in will not do that. I am stumped. I stream to the one in the LR.
    Thanks,
    Art

    artmar1 wrote:
    I want to turn off streaming on one ATV.
    If it is a primary library that you no longer wish to stream, select 'Show only the synced items on my Apple tv' from the summary tab in itunes when the Apple tv is selected in the device menu.
    If it is a secondary library ctrl-click/right-click on the Apple tv in the device list and choose 'turn off streaming' from the contextual menu that appears.
    (Please excuse my unsupported nomenclature)
    Message was edited by: Winston Churchill

  • TS1398 My wifi signal in my iphone 4 is very poor it wasn't the same before. When ever I try to play video it stopes streaming. I hope apple has an answer for this.

    I do not experience any problem browsing Internet or using social networks via wifi but whenever I play a video from YouTube or any other source it stopes streaming after playing 10 to 15 sec video, doesn't matter how close I am from the homehub or which Internet provider I am using. Recently I am experiencing that my phone became slow after installing the new iOS 6.1.2. Application takes time to open. Sometimes application closes on there won without any command. The key l board became slower. I wish I could get the previous version of iOS which was perfect for my iPhone 4.

    Try:
    - Reset the iOS device. Nothing will be lost       
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Unsync/delete all music and resync
    - Reset all settings                  
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                                
    iOS: Back up and restore your iOS device with iCloud or iTunes
      - Restore to factory settings/new iOS device.

Maybe you are looking for