Phone Auto Registration

HI,
I have configured Phone auto registration on cucm 8.6. when I plug the phone it will show tftp not found trust list not update...
if I enter tftp ip manually it will download the new f/w and registered with the defined extension.
How can I get phone to auto registered without manually enter tftp server IP. ?
Thanks.

you need dhcp server to lease ip addresses to phones.
and incliding option 150 for sccp phones and option 66 for sip phones.
options 150 and 66 should point to suscriber1 subscriber2
suscribers should have tftp servers running

Similar Messages

  • IP phone attempted-registrations

    Hello
    I have a router cisco 3945 with ios 15.2(4)M5. Then I enter command 'show ephone attempted-registrations', it doesn't show mac address of an ip phone.  How can the issue be fixed?

    Did you enabled auto registration under telephony services?
    And if you enable debug tftp events you can see all the device which are attempting to register.
    Please rate all the helpful post.

  • Cisco ip phone 9971 registration failed with CME 8.6 on WAN

    Dear  Sir
    Subject: Cisco ip
    phone  9971 registration failed
    with CME 8.6 on WAN
    I have a WAN  simulation with one Cisco2811 router one Cisco1841 router (connected with fast  Ethernet interface) plus one layer 2  switch.
    I upgraded the 2811 IOS to 15.4M and installed CME8.6, when we tried  to add 9971 sip phone If the traffic goes throw LAN (Same subnet- directly from  switch to 2811) everything is fine and the SIP phone (9971) added with no  problem but when I change the subnet and traffic goes throw WAN
    ( from 1841  routed to 2811 with default route) my phone didn't register.
    It will be great  if anybody could help!!
    If you can solve my problem, I will be happy to  compensate.

    Try binding SIP to an interface on which Phone can reach (Use "voice service voip" "sip" and then bind)
    Udit

  • Is there any app for phone auto start after swithced off??

    Is there any app for phone auto start after swithced off??

    Are you looking for an app which will startup the Z10 at a specified time?
    I don't know of one. I have a feeling once OS 10.2 is available you'll see apps such as this.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • E52 phone auto lock

    My E52 has proble. After enanled function phone auto lock period 30 mins, I could not disable it. When i goto phone autolock period, change, select NONE, then it appeared error: phone unable to unlock.
    I tried factory reset and reinstall software but still can not change. I have to enter lock code after every 30 mins phone unuse.
    Anyone can help to fix it? 
    Thanks.
    Solved!
    Go to Solution.

    I found this solution on Blog Hanzz, and it is working
    Menu - cntrl. panel - settings - general - security - phone and SIM card - phone autolock period
    The error was: Unable to change period
    To remove it, I did the following:
    Go to: Cntrl. panel - Phone - Encryption - Phone memory and switch setting to ON
    Reboot Phone (do not know if this is necessary), go back to Phone memory and switch it to OFF
    Now you can change the autolock period to None:-)

  • Cisco ip phone 9971 registration failed with CME 8.5

    Good day!
    I have voice bundle 2951 with 15.1.3(T) IOS version and  a few 9971 ip phones. In addition to it I've downloaded current SIP firmware for these phones (sip9971.9-2-1) and configured my CME as follows:
    voice register global mode cme source-address 192.168.2.254 port 5060 max-dn 10 max-pool 5 load 9971 sip9971.9-2-1 timezone 13 create profile sync 0069043299436028!voice register dn  1 number 104 name 9971 SIP Phone label 104 mwi!voice register pool  1 id mac 688D.ABA4.A88B type 9971 number 1 104 presence call-list dtmf-relay rtp-nte codec g711ulaw no vadvoice service voip sip
      registrar server expires max 3600 min 120
    All SIP firmware files were uploaded to tftp server on CME and shared then:
    tftp-server flash:kern9971.9-2-1.sebn tftp-server flash:rootfs9971.9-2-1.sebn tftp-server flash:sboot9971.031610R1-9-2-1.sebn tftp-server flash:sip9971.9-2-1.loads tftp-server flash:skern9971.022809R2-9-2-1.sebn tftp-server flash:dkern9971.100609R2-9-2-1.sebn tftp-server system:cme/sipphone
    During the boot process all ip settings including option 150 were successfully updated by the phone:
    ip dhcp pool voip_pool   network 192.168.2.0 255.255.255.0   default-router 192.168.2.254   option 150 ip 192.168.2.254
    But when the phone tries to get files on the CME it fails. The ouput of debug tftp events command shows that there is no such configuration file on tftp:
    Jul 28 16:36:14.446: TFTP: read request from host 192.168.2.8(49158) via GigabitEthernet0/1Jul 28 16:36:14.446: TFTP: Looking for SEP68BDABA4A88B.cnf.xmlJul 28 16:36:14.446: TFTP: Sending error 1 No such fileJul 28 16:36:15.522: TFTP: Server request for port 49158, socket_id 0xA2EFEE4 for process 324Jul 28 16:36:15.522: TFTP: read request from host 192.168.2.8(49158) via GigabitEthernet0/1Jul 28 16:36:15.522: TFTP: Looking for XMLDefault.cnf.xmlJul 28 16:36:15.522: TFTP: Opened system:/its/vrf1/XMLDefault.cnf.xml, fd 14, size 3210 for process 324Jul 28 16:36:15.522: TFTP: Sending block 1 (retry 0), socket_id 0xA2EFEE4Jul 28 16:36:15.522: TFTP: Received ACK for block 1, socket_id 0xA2EFEE4Jul 28 16:36:15.522: TFTP: Sending block 2 (retry 0), socket_id 0xA2EFEE4Jul 28 16:36:15.522: TFTP: Received ACK for block 2, socket_id 0xA2EFEE4Jul 28 16:36:15.522: TFTP: Sending block 3 (retry 0), socket_id 0xA2EFEE4Jul 28 16:36:15.526: TFTP: Received ACK for block 3, socket_id 0xA2EFEE4Jul 28 16:36:15.526: TFTP: Sending block 4 (retry 0), socket_id 0xA2EFEE4Jul 28 16:36:15.526: TFTP: Received ACK for block 4, socket_id 0xA2EFEE4Jul 28 16:36:15.526: TFTP: Sending block 5 (retry 0), socket_id 0xA2EFEE4Jul 28 16:36:15.526: TFTP: Received ACK for block 5, socket_id 0xA2EFEE4Jul 28 16:36:15.526: TFTP: Sending block 6 (retry 0), socket_id 0xA2EFEE4Jul 28 16:36:15.526: TFTP: Received ACK for block 6, socket_id 0xA2EFE
    So, i see this file on CME router in system/cme/sipphones direcotory:
    Directory of system:cme/sipphone/  747  -rw-         825  Jul 27 2011 16:10:04 +00:00  featurePolicyDefault.xml  744  -rw-           1  Jul 27 2011 15:59:49 +00:00  OS79XX.TXT  749  -rw-        3761  Jul 27 2011 16:10:04 +00:00  SEP688DABA4A88B.cnf.xml  742  -rw-        1948  Jul 27 2011 16:10:04 +00:00  SIPDefault.cnf  745  -rw-        4376  Jul 27 2011 16:10:04 +00:00  softkeyDefault.xml  746  -rw-        4342  Jul 27 2011 16:10:04 +00:00  softkeyDefault_kpml.xml  743  -rw-          69  Jul 27 2011 16:10:04 +00:00  syncinfo.xml
    So, i dont quiet understand why the registration process was failed. Could anyone tell me if there are restrictions on the SIP firmware and IOS version in this case?
    Thank you.

    linuxchild,
    thank you. i checked this out, but i think it doesnt matter whether tftp-path statement is set or not in this case.
    Configuration files for 9971 are located in system:cme/sipphone directory by default.
    While I have this statement in tftp-server configuration, it should get this file from the server.
    tftp-server system:cme/sipphone
    i tried to configure it accordiing to this example.
    Now i can see xml file in flash direcory:
    30        1948 Aug 1 2011 09:48:52 +00:00 SIPDefault.cnf
    31          69 Aug 1 2011 09:48:52 +00:00 syncinfo.xml
    32        4342 Aug 1 2011 09:48:54 +00:00 softkeyDefault_kpml.xml
    33        4376 Aug 1 2011 09:48:54 +00:00 softkeyDefault.xml
    34        3787 Aug 1 2011 09:48:54 +00:00 SEP68BDABA4A88B.cnf.xml
    35         825 Aug 1 2011 09:48:54 +00:00 featurePolicyDefault.xml
    But i cant still get this file from tftp and have the same error:
    *Aug  1 09:50:27.385: TFTP: read request from host 192.168.2.5(49157) via GigabitEthernet0/1
    *Aug  1 09:50:27.385: TFTP: Looking for SEP68BDABA4A88B.cnf.xml
    *Aug  1 09:50:27.385: TFTP: Sending error 1 No such file
    Has anyone had such problem?

  • My phone auto synced with my pc now all my vids are gone is there a way to retrieve them?

    Hi I connected my phone to my pc to charge it and it auto synced I had videos on the phone of my sisters wedding is ere anyway to get these back once the sync has been completed. I attempted to load the backup created before the sync but it didn't changed anything. Please help as Hess videos are very importan to me

    Photos/videos captured by the iPhone which are stored in the iPhone's Camera Roll are not touched or included with the iTunes sync process except for being included with the iPhone's backup.
    If these were videos that were captured by your iPhone, they weren't removed from your iPhone's Camera Roll by syncing with iTunes alone, which is not possible.
    What else was done besides syncing? Even if this could be done by syncing with iTunes alone, there is no setting under any of the various tabs for the iPhone sync preferences with iTunes that has anything to do with or affects the Camera Roll.

  • Why doesn't my phone auto-lock after one minute?

    From the settings - it's checked to auto-lock after a minute, but for some reason - this does not always happen. I have tried turning off the phone and back on again - that did not work. How can this be resolved?

    probably. turn it off for sometime , restart the phone and check.

  • CUCM 7.x, auto registration not assign the correct auto extensions

    Hello,
    I have a site that that when I plug an IP phone I get an extension in the range of 2400 instead 4100 range. Any IP phone I plug in any site should be in the 4100 range don't know why only this site auto registers phones in the 2400 range.  Also one phone register with an extension of 2428 but did not show up in call manager. Any suggestions why this is happening. 
    Thanks.
    Horacio

    Hi Horacio,
    If you have a phone that's registered, but not in your callmanager, my first step would be to see where it is registered to.  Check on the phone to see what the tftp server is.  It honestly sounds like you've got the dhcp scope at that building poined at a different CUCM cluster.
    hth
    Rick

  • RV220W: VoIP phones losing registration and staying offline

    Hi all,
    VoIP phones connected to a Cloud PBX provider are losing their registration to the Cloud PBX. The router in question is an RV220W.
    This started occurring when more phones were added to the site. Phones will boot up, register and then lose their registration within a minute or two. 
    A larger number of phones of the same model with identical config are connecting through a Cisco 871 router without issues so we know the phones and their configs are good.
    SIP ALG is disabled.
    The UDP session timeout duration is 120 secs. The phones are set to re-register every minute.
    What could be wrong?

  • FXS/Analog phone auto-dial when picked up?

    Hello.  UC540 862.  I have a door intercom i have patched into the phone system via FXS port (will not use FXO).  When the button is pressed on the door intercom, you get a dial tone over the speaker and the FXS port is open.   Is there a method to have it auto-dial an extension?   I've setup lobby phones that intercom a specific phone internally, but in this case, i need it to autodial a main hunt group- ext 101, which blasts 4 people.  Unfortunately the door unit does not have a dial-pad.
    Thanks in advance.

    didn't work but again - fxs port as it's not compatible with fxo port ..  (below readout).. trying connection plar 101.. maybe that'll work
    KMK-UC540(config-voiceport)#do show voice port sum
                                               IN       OUT
    PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
    =============== == ============ ===== ==== ======== ======== ==
    0/0/0           --  fxs-ls      up    dorm on-hook  idle     y
    KMK-UC540(config-voiceport)#voice-port 0/0/0
    KMK-UC540(config-voiceport)#intercom 101
                                  ^
    % Invalid input detected at '^' marker.
    KMK-UC540(config-voiceport)#int ?
    % Unrecognized command
    KMK-UC540(config-voiceport)#

  • Phone auto connects to internet

    with every sms the phone gets connected to the internet and remains connected unless explictly disconnected thru connection manager
    Does anyone know why is this connection , and which app may be causing this

    as chanchan kinda said the email client usually connects with the N8, try telling it not to auto update

  • Send my iphone for replacement, Iphone is replaced and has a new IMEI. Now I need to pay approx 100 Euros to get my phone legally registrered again in Turkey.

    The thing is if you get a phone from another country and want to use it in Turkey you need to register your IMEI code and pay a fee of approx 100 euro to get it registrered officially + u need to show a stamp of entering the country on your passport. This is done to prevent stolen phones to be sold.
    Now the thing is.. I registrered my imei of my iphone 4. But after some time the homebutton wouldnt work so i send it to get replaced. Now the iphone 4 got replaced = refurbished = new IMEI. That means I got to register again and pay 100 euros.
    Internally Apple knows that my old IMEI is replaced to another one. Cant I get an official document or whatsoever to prove it?
    Does this mean I am screwed ? (Pardon my English, its not my main language.)

    All cell phones, when replaced, will have a unique IMEI. This is not unique to Apple. If you want documentation that it was replaced by Apple, ask Apple for documentation.
    We have no way of knowing whether they can or will provide this. We're just customers like you.

  • RV042 VoIP-phone reports "Registration failed"

    This is a continuation of a discussion that I erroneously marked "answered".
    The title was "RV042 protocol binding for SIP and RTP (VoIP)"
    I would like to provide a link to it here but I don't know how.

    Problem is solved. Reason was that Network Service Detection was enabled and the Default Gateway did not respond to ping requests which resulted in a WAN failure condition with the consequence of protocol bindings failing over to the working WAN which is inappropriate for the IP-phone registering with the IP telephony provider.
    Best regards, Felix

  • Auto registration in SUP 2.2

    Hi All,
    I want to auto register my application on sup 2.2 currently i am generating activation code manually from sup server than after that registering device.
    But now we have more than 500 users and manual process is too complex. Now i want to automatic register app can anybody plz help me how can i proceed with this process ?
    Regards
    Anupam Srivastava

    You need to create a new security profile in SCC and deploy the MBO to that security profile instead of using default security "admin". You can follow the blog I mentioned to understand how to create a new security profile in SCC (refer SCC configuration section steps 1,2 and 3 in the blog). From the "authentication provider" tab you will be able to select different authentication types. For LDAP authentication you need a LDAP server configured in your environment. Also note that when you create MBO keep the credentials dynamic with the default "username" and "password" selected as in image no.5 in blog.
    Available security providers:SyBooks Online
    LDAP configuration detials: SyBooks Online
    Midhun VP

Maybe you are looking for

  • LMS 4.2.2 Fault Discovery - Network Adapters Limit Exceeded

    Running fault device discovery after adding approx 50 new devices to LMS DCR. It seems I have reached a limit in DFM with regards to how many device components it can manage. The devices are put into questioned mode and the following error is seen in

  • Deploying oracle forms in tomcat

    dear all, i developed a small application using oracle Forms 10g that it s okay under OC4J and i d like to deploy it in a tomcat container installed as a standalone web server or in apache web server , can you lead me to a blueprint document that sho

  • What are the components of sap script?

    what are the components of sap script?

  • Creating Tabs for Dashboard Prompts

    Hi Experts I currently have two dashboard prompts on 1 page 1) By Year 2) By Finanical Year The user should only be allowed to use one prompt (at one given point) , therefore the other would be an alternative. Is there a way of creating tabs 2 within

  • Dynamic link and workflow optimization help needed

    As a vlogger I just tried out a brandnew method to save time and renders. Instead of editing every clip separately in After Effects and then rendering it and then do the final edit in Premiere, I just edit immediately in Premiere, then when it's fini