Phone Firmware upgradation

Hi All ,
Again I am distrub you guys, I have some issue to discusses with you guys, if you have time please help me out for this.
My problem is that we a one CUCM(Ver 8.0.3) Cluster and we have more then 9000 phone device with dfferent models with more then 100 locations, like
6921
6941
7925
7937
7942
7942G
7960
7961
7962
7962
7970
but most of them are 7942G,
we already upload all new firmwares on our CUCM cluster but not using new firmware right now ,
now challenge is that that we have to upload these new firmwares site by site because we have more then 100 side and more then 9000 devices
and we are not sure that if we upload in one shot for all 9000 deveice so what kind of the issues we will face.
So my problem is that I need a information that how to upload these new firmwares site by site with minimal facsing issues, so my request to all of you that
please help and guide me , I will be thankfull to all of you.
Hop i will rceeive reply very soon.
Thanks
RS

You can upload it to your TFTP servers and then use BAT to set the FW phones need to download in batches.

Similar Messages

Phone Firmware upgrade Startegy for 9.1 -- 10.5 migration

Hello,
We are planning our migration from CUCM 9.1 to 10.5.
I want to do a phone firmware upgrade before upgrading the cluster, to minimize phone upgrades. Planning to use PFD (Peer File) for this.
My question is, what would be the best strategy to upgrade the firmware?
I am not sure if the current load in 9.1 will be supported by 10.5, and if 10.5 device pack/load is installed on 9.1, would 9.1 support it.
So should I upload the 10.5 pack on 9.1 and upgrade the phones in groups, or would 10.5 support it.
The other thing is, I just want to confirm, after a cluster reboot/version switch (in upgrade), would the phones restart and try to upgrade or would only try to connect to available CUCM.
The compatibility Matrix is a bit confusing.
Thanks,
AK.

Thanks for the reply guys.
I DID try to upload the 10.5 pack in CUCM 9.1, but it rejected it. so no way it will do that.For the file this is what I understand:
1- COP files: contain script to upgrade the firmware
2- loads files: contains the actual firmware
So would a good strategy be:
-Register all phones on Sub first. Keep Sub as Primary.
-Upgrade Publisher.
-Register a group of phones on Upgraded publisher (by making changes on PUB), by making Pub primary for them.
-the Phone group Upgrades the firmware
-Group of Phone gets upgraded. move to next group.
-After all Phones are upgraded, upgrade the sub.
If there is a better way to do it, please let me know. The biggest challenge we have is to get all 3000 phones migrated in 1 night.
Thanks guys. Appreciate it!

Phone firmware upgrade

How can new phone firmware be installed on BE3K phones? I'd like to upgrade 6945's to 9.3(1) to implement new jitter buffer operation.
Thx, Jim

Hi Jim
1) You need to copy the firmware file to USB key or SFTP server. Then select the file from the location
2) Yes
Uploading the firmware should take about 10 minutes. Since reboot is required, there is additional 20-25 downtime because of it.
Once the server and phone is rebooted, it should get the new firmware. Each release has a software compatibility matrix. Please check that it is according to the table below
http://www.cisco.com/en/US/docs/voice_ip_comm/cucmbe3k/compat/3kcompmtx.html
Thanks

CUCM 9.1 Phone 7975 upgradation issue

Hi
Recently we upgraded CUCM 7.1.5 to CUCM 9.1.
IP Phone 7975 old firmware was 9.0.x and cucm 9.1 was loaded with firmware 9.3.x
somehow 7975 phones didnt upgraded firmware to version 9.3.x
Also noticed when we factory reset 7975 phones, it loaded SIP firmware....! But that phone is added as sccp.
Once we delete and reconfigured the phone, then only phone firmware upgraded to 9.3.x.
Any sugestion, why IP phone 7975 not taking firmware version 9.3.x? also when we did factory reset why it is loading with sip firmware ?
we have 7911 phones, those phones taken new firmware without any problem.
cucm ip : 192.168.17.1 and 2
I have attached IP phone span PC wireshark capture and IP Phone console log and version screenshot.
Pls. suggest
Rgds
Rajesh kumar

Looks like this phone has a problem parsing it's configuration file, given the firmware version it should upgrade to is contained within that config that would indicate why.
If you have a look in file 'log3' there are the following entries:
697: ERR 14:08:30.663131 JVM: Startup Module Loader|cip.xml.ap: - XML Parser Exception: name expected (position:START_TAG @113:2 in java.io.InputStreamReader@3a4675) (line=113)
698: ERR 14:08:30.664676 JVM: Startup Module Loader|cip.cfg.s:? - ERROR PARSING CONFIG file:ram/SEP1C17D337295A.cnf.xml
699: NOT 14:08:30.666919 JVM: Startup Module Loader|cip.cfg.s:? - Config processConfigNoError() result code=CONFIG_FILE_BAD_FORMAT
If you have a look at this post it relates to this error and should help you to resolve the issue:
https://supportforums.cisco.com/thread/2129364
It would appear that the config file includes a tag, if you open the config file for the phone:
http://192.168.17.1:6970/SEP1C17D337295A.cnf.xml
Then hopefully you can locate the null entry (should be line 113 of that file), go to UCM and set the corresponding parameter (i.e. under Common Phone Profile), that should hopefully prevent the null entry from being generated in the config file and allow the config file to be parsed correctly.
If you are still having issues post the config file and I'll have a closer look, it wasn't in the packet capture.
Thanks
Stephen Welsh
CTO
http://www.unifiedfx.com

After the firmware upgrade last week, the local WIFI networks pop up when I turn on my phone, I have WIFI turned off, how do I turn off the pop up?

After the firmware upgrade last week, the local WIFI networks pop up when I turn on my phone, I have WIFI turned off, how do I turn off the pop up?

What OS X version are you using?
Can you take a screenshot of the pop-up notification?
To take a screenshot hold ⌘ Shift 4 to create a selection crosshair. Click and hold while you drag the crosshair over the area you wish to capture and then release the mouse button. You will hear a "camera shutter" sound. This will deposit a screenshot on your Desktop.
If you can't find it on your Desktop look in your Documents or Downloads folder.
If you want to attach a screenshot to a response here, click the "camera" icon above the text field:
This will display a dialog box which enables you to choose the screenshot file (remember it's on your Desktop) and click the Insert Image button.
⌘ Shift 4 and then pressing the space bar captures the window the cursor is on.
⌘ Shift 3 captures the entire screen.

HDMI output not working since firmware upgrade

I would appreciate troubleshooting tips for getting the HDMI output to work. I just tried it recently for the first time in a long while, approximately 4 weeks after doing the firmware update to 2.2. When I did it before, plugging in the HDMI cable would automatically start output to my HD TV. Now that is no longer the case. Changing the HDMI output from "Auto" to "720p" does not make a difference either.
Otherwise, everything works well and I've been satisfied with my Creative 7 to date. I have installed several apps so it could be that there is a conflict and nothing related to the firmware upgrade.
Any troubleshooting suggestions would be appreciated.

Well I've received my refurbished device for about a week now. The HDMI still doesn't work either with Zii Video or a 3rd party app MoboPlayer. ?I am tempted to reinstall the firmware upgrade again. Is it ok to try this or is it only a one time attempt?
Perhaps this should be a separate thread but are any of the "Phone 2 SD" apps compatible with the Ziio 7? Whenever I use the "Move to SD card" option, there is still no program moved to the external SD card. ?I have a Ziio 7 with 6 GB of memory as well as a 6GB micro SD card. ?My memory settings are:
- SD Card: total space - 5.43GB; Available space - 5.43GB
- Device media storage: Total space - 2.48GB; Available Space - 2.3 GB
- System storage: Total Space - .97 GB; Available space - .59GB
In Settings>Applications>Manage Applications, the "On SD Card" tab lists several programs lists several apps but none of them are actually on the external SD card.

No contacs after firmware upgrade on N70

Hi
I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
I did the upgrade again just to make sure that everything went OK with the same result.
Can some help or has the same problem?
Firmware V 5.0638.3.0.1 18-09-06 RM-84
PC Windows XP SP2
Nokia PC Suite 6.82.22.0
NSU 1.2.0en
Best regards
Chris

not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

Firmware Upgrade and Battery Life?

Since the firmware upgrade on my Macbook in early February the fan appears to be running at full speed all the time and battery life is crap! Has anyone else noticed this? Is there a fix/workaround available please?

Sounds more like an app stuck processing that shouldn't be....does happen from time to time. Behing hot means it is constantly processing.
To fix:
Try a reboot (described below).
Think of it this way, the iPhone is more of a computer than a phone. It suffers from being a new OS and nobody can deny there are not bugs and memory leaks. The longer left running, the more things start to fail or slow down (I have had the iPhone since day one of original phone and I am just speaking from my experience). Thus I equate it to like when Windows95 came out...not sure of your age or if you remember those days...but back then it was a running joke of how many days you can keep Windows 95 running before you had to reboot. I am sorry to say but the iPhone is the same way right now (but getting better with a few hiccups back during the 2.0 release). So for me, I reboot daily when I leave in the morning and take it off the charger. By doing so I rarely see any lag or problems.
A reset/reboot is:
Go to Home Screen
Press and Hold Home Button
Keep holding and press and hold Lock Button
Keep holding Both
You will see Slide to Turn Off (Don't let go to slide, just keep holding)
The phone will turn off (in time, but screen will look like it has some white lines)
Keep Holding
When you see the Apple Logo, you can let go.
Turning off via the Slide to Turn off while good and fine to turn off, is more like the Sleep Mode on a computer. Thus any locked up issues in memory remain when you turn back on. A reboot as described is like doing a real Turn off and Turn On on a computer.
You may also wish to read this tread about reboots and odd application behavior.
http://discussions.apple.com/message.jspa?messageID=5851978#5851978
For me, 2.1 works great.

Firmware upgrade encountered an issue

Right now my Galaxy S3 is sitting at a screen that states "Firmware upgrade encountered an issue. Please use Software Repair Assistant & try again." Whenever I power on my phone, I get that message. I've tried to do an Emergency Recovery in both Kies and Kies 3, but neither are able to recover, and the only way, it seems, to get the SRA is to plug my phone into my PC and get it from Autorun. Since my phone is not leaving the error screen, I don't get the auto run option to install the SRA. Is there any way to download it manually to get my phone running, or is it pretty much bricked and I'll have to look at replacement options?

I found a solution on the XDA forums site, but thanks anyway. Looks like I just needed to run the Software Repair Assistant, which I'm a little surprised that the Verizon store I went to didn't have it on hand to attempt to fix my phone. I got my device repaired, and it's working great. Just really wish my Wiimotes worked in Android 4.3.

Firmware upgrade failed, printer now say i has firmware version 0. attention light lights up

Hey all
I had a problem printing a pdf on my mac, and then tried to upgrade my mac driver and printer firmware.
But the firmware upgrade failed for some unknown reason. And now the printer just have the ready and attentions lights on constantly.
I have tried to restart and reset the printer many times, and tried the HP firmware upgrade utility several times, with no luck. It just say it was "failed to upgrade"
Any idea what to do ??
My printer is a HP Laserjet Pro CP1025nw
Thanks
Jan

Hello Jan
It definitely sounds like the firmware update failed. Firmware is like a devices Operating System. Without it, it can't do much. This is backed by the "failed" message and that your printer reports it has version 0.
The printer will need to be serviced. Please call HP Phone Support at 1-800-474-6836.
Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
When a solution is found please mark the post that solves your issue.

Firmware upgrade for Nokia 6280

I would like to know do we have firmware upgrade for Nokia 6280 as my present one is 3.65 and would like to upgrade it to 5.92 and I am in India
Could you please help me out.

updating to new firmware depends on product code which represents your region of purchasing, language pack and if it's branded or not .... so NOKIA releases firmwares and release it for every product code depending on mentioned points
you can check for updates @ :
http://mea.nokia.com/support/download-software/device-software-update/can-i-update
To find what the latest available device software is, you’ll need your device’s product code. The code is printed on the white label beneath the battery (e.g. CODE: 0520001).
if your phone is branded with an operator, that means that you should go to the operator care center and ask them, not NOKIA
some updates delay in some countries variant product code, as it requires more effort to add language pack to it like "example. China Japan Korea" or it needs the country to approve it due to its policy
-you can show appreciation to my posts if it helped or useful by pressing the green Kudo star beside my post that hepled
-if my answer was the solution , so click accept as solution button
Started From Nokia 3310 , Now with Nokia N97 v.22.0.110 + N900 PR1.2

Firmware upgrade Nokia 5230 - SLOW device!

I see that the device 5233 had an firmware upgrade availibe from 12.1.089 to 12.1.092. This upgrade is now not availible for the nokia 5230. This device is much slower than the 5233 and 5800.
Is there a way to make this upgrade also soon availible for the nokia 5230? Because this device has now only the firmware version 12.1.089

try to uninstall them and re-install on memory card not phone memory
it's the reason if you installed these apps on phone memory
+ change the messages to be stored on memory card not phone memory
-you can show appreciation to my posts if it helped or useful by pressing the green Kudo star beside my post that hepled
-if my answer was the solution , so click accept as solution button
Started From Nokia 3310 , Now with Nokia N97 v.22.0.110 + N900 PR1.2

Firmware upgrade nokia CK-7W car set

Hello.
Is it possible to firmware upgrade the car kit CK-7W ?
I have problems that the audio connection between my Nokia 6210 Navigator and CK-7W is is in falling out periodical.
I have the lates firmware in my nokia 6210 navigator (3.25)
Message Edited by hchdk on 01-Jan-2009 11:03 PM

Thanks for the response.
The car kit was installed by a Car Phone Warehouse Nokia approved fitter about 4 years ago The kit has worked really well until recently!
The contol button doesn't seem to be stuck in and responds as it should to button presses. In terms of the cable being squashed or damaged. Obviously there is a chance, but in actual fact, only an inch is on show before it is hidden behind the dashboard. In this instance I'm not sure what damage might occur since I don't know how to remove the dash!
Apologies, I'm not certain I understand your comment re:
- "You can rule out the button by disconnecting it then starting the car and connecting, before switching off the car to see if the kit shuts down."
How do I disconnect the button? Does it pull away from the lead / cable?
Many, many thanks for your help,
Chris

E71 Firmware Upgrade Step-by-Step (Undocumented Ti...

Although Nokia’s firmware upgrade claimed to be smooth using Nokia Suite, the fact it is not. There are many things which could interfere with the process. For example upgrading E71-1 firmware from 100.07.76 to 110.07.127 is not always trouble free. Based on experience, here are precautions to take:
Before you begin:
• Make sure your phone and computer/laptop are fully charged.
• Make your personal data is backed up safely.
• The BEST, FASTEST and EASIEST way of saving your personal data is making a copy of your phone memory on a memory card. Choose Tools > Memory > Options > Back up Phone Memory and wait until it will be competed.
• Make sure Nokia PC Suite is not running.
Upgrade Process Instructions:
1. Download and install latest “NokiaSoftwareUpdater” http://europe.nokia.com/A4579163 .Reboot if required.
2. Disable Antivirus or any other interrogative software on your PC.
3. Launch “NokiaSoftwareUpdater” and follow instructions
4. When prompted, connect your phone, in this case E71.
5. A 3-step process will start, identifying your phone, downloading latest firmware and upgrading to latest firmware. (a process of 15 min.)
Following those instructions will ensure a hassle-free upgrade.
Good luck.

I have a related issue on my E71-3 (New Zealand). Since moving to Firmware 501.21.001 contacts I have in 1-touch keep dropping off - not all, just the odd one here & there. In addition, the group ring tones for the same contacts are dropping off. Very odd. Most frequently it is my partners number impacted, which is why the issue stands out to me ... On start up, I'm now getting a message saying not all applications can be loaded from the memory card - on checking app manager, they are all loaded ... Anyone else having these issues?
iPhone 4 is looking more & more tempting by the day ;-p

Nokia 5230 - Wish List for Next Firmware Upgrade

heya guys,
I'm using Nokia 5230 with the latest firmware, V 12.0.089.
The following are my wish list for the next firmware upgrade:-
1. Messaging > Sent Items: Please include short cut icons to Forward, Create New and Delete as in Inbox.
2. Log > Recent calls: Unnecessary option for Call > Voice Call.
3. Settings > Personal > Themes > Call image > Theme image: A bug with certain 3rd party theme (e.g. JustBlack - 5th theme). During lock mode, screen is totally blank during calls & alarms.
4. Settings > Application mgr. > Installed apps.: Too much application will cause an error of "Application Manager Memory full" and auto exit when selecting "Option". During error, phone memory is around 25MB, Memory Card is around 2.5GB/4GB.
5. Ovi Map > Drive / Walk > Set Destination: Please do an icon based UI for History, Favourite, Search & From Map. The list is to small to click on to (when driving) :-)
6. Organize > Please include multiple selections. E.g. Mark/Unmark > Mark / Mark All. Easy to move multiple applications at once to any folder.
That's all for now i guess. By the way, Nokia rocks!!
Thanks in advanced.

Please integrate swype for messaging in the next firmware of 5230. Also kinetic scrolling for messages and contacts. If possible the homescreen of symbian^3.

Phone Firmware upgradation

Similar Messages

Maybe you are looking for