Phone in FXS Port in Key mode
I have a system in Key Mode, and cannot seem to figure out how to get an analog phone that's plugged into the FXS Port to make an outgoing call.
Hi Russ,
In pure key system mode the FXS port (and SPA502 phone) can't be configured as a member of a Shared FXO Line. There is no way to directly reach these phones on an inbound call. They can however, be used to make out bound calls if the system is configured in blended mode and the option 'Include in Outbound calls' is checked on the Shared FXO Lines page. In this scenario the FXS phone would dial 9 + address and the system will let the FXS use an idle FXO that has that capability enabled.
Hope this helps.
Chris
Similar Messages
-
Can't transfer to an analog phone on FXS port (CME2811)
I have six IP phones with locals 501 to 506. Additionally, I have four analog phones (locals 541 to 544) connected to a VIC2-4FXS card on a 2811 with CME and CUE module.
All phones can call each other. But if say, a user on an IP phone calls a 2nd user on another IP phone, the 2nd user cannot transfer to the 54x locals. She hears a busy or reorder tone (still need to verify which) after keying in the 2nd digit (ie. 54 then "busy" tone)
Am I missing something?Under telephony-service configuration enter the transfer-pattern command. For example:
router(config)#telephony-service
router(config)#transfer-pattern 5..
If no transfer pattern is set, transfers are only permitted to other IP phones.
Hope this helps. If so, please rate the post.
Brandon -
Is there a way to make an analog phone connected to an FXS port a part of a call pickup group that contains both analog phones & IP phones? I setup a lab and used MGCP to add the gateway and I was able to add the DN associated with the FXS port to a call pickup group. However, I am unable to figure out how to answer the call from the analog phone when another IP phone in the call pickup group is ringing.
Thanks in advanceHi
You are going down the right track with this.
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dde5372/0#selected_message
See this other post I made (for a different purpose, but the principal is the same - it just opens up features available to IP phones for FXS ports by registering them using SCCP).
Regards
Aaron
Please rate helpful posts... -
Hello,
I have a problem with my SPA3102's FXS port.
In last April I tested my friend's two PAP2T adapters with four phones. The adapters were connected to same switch with different fix IP addresses and phones were able to ring each other. Then I got one of adapters from him as a gift and on 2nd of January I bought an SPA3102 - so I have two adapters.
I connected my adapters to same switch. Their parameters are:
PAP2T IP: 192.168.0.221
FXS #1:
SIP port: 5060
display name: 1
user ID: 1
FXS #2:
SIP port: 5061
display name: 2
user ID: 2
SPA3102 IP: 192.168.0.222
FXS:
SIP port: 5062
display name: 3
user ID: 3
Dialplans:
PAP2T Line1: (<2:>S0 <:[email protected]:5061>|<3:>S0 <:[email protected]:5062>|<[x*]:>S0 <:[email protected]:5060>)
PAP2T Line2: (<1:>S0 <:[email protected]:5060>|<3:>S0 <:[email protected]:5062>|<[x*]:>S0 <:[email protected]:5061>)
SPA3102 FXS: (<1:>S0 <:[email protected]:5060>|<2:>S0 <:[email protected]:5061>|<[x*]:>S0 <:[email protected]:5062>)
Well there is problem with third phone (SPA3102 FXS port). Phones with PAP2T work perfectly, they can call each other. The 3rd phone has dialtone sometimes only but it is unable to call the other two phones. "1" and "2" can call third phone sometimes but another time I get reorder tone when I dial "3".
I have made backups from adapters' settings. Does somebody have any idea about this problem?
Thanks in advance,,,Hi,
Problem is solved...
SPA3102 has two RJ45 outlets: LAN and WAN (internet). I have used LAN only because of switch and the INTERNET terminal was empty. It appears to me this situation drives SPA3102 crazy... I had to make a "loopback" plug (I linked contact 1 to contact 3 and contact 2 to contact 6) and insert it into INTERNET outlet. So all of phones work well...
If you want to use a PAP2T lonely (without internet access) as a "micro-PBX" with two extensions, you will have to use same plug otherwise phones won't work. -
Call Manager register fxs port with voice gateway- problem
I have a CUCM 6 and a Voice Gateway V224. I've configured the voice gateway's voice FXS ports as MGCP.
I have a Voip connected and registered to the CUCM and a Pots phone connected to the Voice Gateway.
If i dial from the Voip to the Pots phone it rings. The problem is that i cannot ring from the Pots to the Voip phone.
I have no dial tone.
If i write no shut down on the voice port i have a tone. If i configure mgcp on the voice port i have a busy ringtone.
I've entered no mgcp and mgcp commands and i've reset the voice gateway.
How can i call from the pots to the voip phone?
The ios version on the voice gateway is Version 12.4(22)T4.
Here is an outghtput from the Voice gateway.
ccm-manager mgcp
ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 10.1.1.33
ccm-manager config
mgcp
mgcp call-agent CCMIOSS 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp validate domain-name
mgcp rtp payload-type g726r16 static
mgcp profile default
timeout tone busy 600
timeout tone dial 600
dial-peer voice 999223 pots
service mgcpapp
port 2/23
dial-peer voice 999222 pots
service mgcpapp
port 2/22
dial-peer voice 999888 pots
service mgcpapp
port 2/23
The CUCM 6 is registered with the voice gateway.Is your campaign using CPA? If so, what's the behavior if CPA is not enabled?
I think the best thing to do is to run a trace...
Call Manager > Cisco Unified Serviceability > Trace > Configurations
Select a CUCM server - any subscriber would work.
Service Group - CM Services
Cisco CallManager (Inactive)
Enable SIP Stack Trace and apply to all nodes. Download and install RTMT
Make a bunch of outbound tests and then open RTMT > Trace & Log Central > Collect Files > Check "All Servers" for Cisco CallManager > Next > Next > Relative Range if you made the test calls within the last X minutes, otherwise you can set a From and To datetime. Click Finish and go through your SDL logs and see what errors you find and post them here.
Also, make sure your phone is in the correct CSS in Call Manager -
Multiple FXS ports on a 3745 to the PSTN
Hi,
I'm putting together a spec to have 35 FXS ports routed directly to the PSTN via an ISDN PRI.
Can anyone foresee any issues with doing this with a 3745, fitted with 3 x NMHDA-4FXS + 3 x EM-HAD-8FXS + appropriate PWDM2 mods + NM-HDV-E1 (or AIM-MFT VWIC?) + appropriate IOS image?
This would be a standalone system (e.g, not controlled by a CallManager), and all the phones will need dedicated lines. And each port will need to be able to generate a line reversal signal.
Any input on this would be appreciated.
Cheers,
J.You can go through the following document and check whether the current IOS version supports it .
http://www.cisco.com/en/US/products/hw/routers/ps282/products_data_sheet09186a0080091ba1.html -
I am using Call-manager 6.0.1b, a MGCP controlled Gateway.On the Gateway i have installed a NM-HD-2V with a Vic2-2FXS module. On this module i connect 2 analog phone with capability to display the Caller-ID. When i call the analog port from a ip phone or from the other analog phone the Dn is not shown. When i connect the phone directly to the PSTN and dial this nr via my cell phone the nr is shown so i expect that the nr format received is not correct. How can this performed that the correct format is shown to the FXS port connected phone ?
Hi,
Yes - you are correct. Looked at this one too quickly.
You will want to make sure the CPTONE defined on the port is for the country the phone is manufactured for, and that the voice-pport has the 'caller-id enable' command.
If those are both correct, and I'm guessing that they are since some caller-id works, then you need to inspect the gateways that take the calls to begin with.
Do you have caller-id trouble for internal calls also?
How do these calls come into your network?
hth,
nick -
CFwd on FXS-Ports (mgcp)
hi!
How can I forward the Calls on an Phone witch is connected to an FXS-Port (mgcp, vg200)?
How can I use the other Features, like PickUp etc.
vy MarkusSince there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting. -
Fxs ports state unknown cisco 1861
Hello ,
Cisco router 1861 the ports are unkown state .
I tried 'mgcp' 'no mgcp'
show ccm
Primary Registered 172.26.4.2
First Backup Backup Ready 172.26.4.1
Second Backup None
Current active Call Manager: 172.26.4.2
Backhaul/Redundant link port: 2428
Failover Interval: 30 seconds
Keepalive Interval: 15 seconds
Last keepalive sent: 09:44:49 UTC Dec 25 2013 (elapsed time: 00:00:13)
Last MGCP traffic time: 09:44:49 UTC Dec 25 2013 (elapsed time: 00:00:13)
Last failover time: 11:30:26 UTC Dec 22 2013 from (172.26.4.2)
Last switchback time: 11:31:11 UTC Dec 22 2013 from (172.26.4.1)
Switchback mode: Immediate
MGCP Fallback mode: Enabled/OFF
Last MGCP Fallback start time: 04:54:21 UTC Dec 8 2013
Last MGCP Fallback end time: 11:25:42 UTC Dec 22 2013
MGCP Download Tones: Disabled
TFTP retry count to shut Ports: 2
FAX mode: disable
Configuration Error History:
store179#show mgcp endpoint
aaln/S0/SU0/0@store179
aaln/S0/SU0/1@store179
aaln/S0/SU0/2@store179
aaln/S0/SU0/3@store179
aaln/S0/SU1/1@store179
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0 -- fxs-ls up dorm on-hook idle y
0/0/1 -- fxs-ls up dorm on-hook idle y
0/0/2 -- fxs-ls up dorm on-hook idle y
0/0/3 -- fxs-ls up dorm on-hook idle y
0/1/0 -- fxo-ls up down idle off-hook y
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0 -- fxs-ls up dorm on-hook idle y
0/0/1 -- fxs-ls up dorm on-hook idle y
0/0/2 -- fxs-ls up dorm on-hook idle y
0/0/3 -- fxs-ls up dorm on-hook idle y
0/1/0 -- fxo-ls up down idle off-hook y
I have dial-peers for the ports .
Any ideas ?Debug mgcp packets
*Dec 25 13:13:25.808: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951726 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:13:25.820: MGCP Packet received from 172.26.4.2:2427--->
200 257951726
<---
conf t
Enter configuration commands, one per line. End with CNTL/Z.
store179(config)#no mgcp
WARNING: no mgcp: Teardown MGCP application may take a while to clean up resources
store179(config)#
*Dec 25 13:13:36.220: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951727 *@store179.super-pharm.co.il MGCP 0.1
RM: graceful
RD: 0
<---
*Dec 25 13:13:36.228: %MGCP_APP-6-MGCP_SHUTDOWN_COMPLETE: MGCP Shutdown has completed
mgcp
store179(config)#
*Dec 25 13:13:46.980: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951729 *@store179.super-pharm.co.il MGCP 0.1
RM: restart
<---
*Dec 25 13:13:47.004: MGCP Packet received from 172.26.4.2:2427--->
200 257951729
<---
*Dec 25 13:13:47.008: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773851 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.008: MGCP Packet sent to 172.26.4.2:2427--->
200 34773851 OK
<---
*Dec 25 13:13:47.008: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773852 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.012: MGCP Packet sent to 172.26.4.2:2427--->
200 34773852 OK
<---
*Dec 25 13:13:47.012: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773853 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.012: MGCP Packet sent to 172.26.4.2:2427--->
200 34773853 OK
<---
*Dec 25 13:13:47.012: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773854 AALN/S0/SU1/[email protected] MGCP 0.1
X: 0
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.016: MGCP Packet sent to 172.26.4.2:2427--->
200 34773854 OK
<---
*Dec 25 13:13:47.016: MGCP Packet received from 172.26.4.2:2427--->
RQNT 34773855 AALN/S0/SU0/[email protected] MGCP 0.1
X: 2
R: L/hd
Q: process,loop
<---
*Dec 25 13:13:47.016: MGCP Packet sent to 172.26.4.2:2427--->
200 34773855 OK
<---
*Dec 25 13:13:47.020: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951731 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:13:47.020: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773856 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.024: MGCP Packet sent to 172.26.4.2:2427--->
200 34773856
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.024: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773857 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.024: MGCP Packet sent to 172.26.4.2:2427--->
200 34773857
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.028: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773858 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.028: MGCP Packet sent to 172.26.4.2:2427--->
200 34773858
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.028: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773859 AALN/S0/SU1/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.032: MGCP Packet sent to 172.26.4.2:2427--->
200 34773859
I:
X: 0
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.032: MGCP Packet received from 172.26.4.2:2427--->
AUEP 34773860 AALN/S0/SU0/[email protected] MGCP 0.1
F: X, A, I
<---
*Dec 25 13:13:47.032: MGCP Packet sent to 172.26.4.2:2427--->
200 34773860
I:
X: 2
L: p:10-20, a:PCMU;PCMA;G.nX64, b:64, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-220, a:G.729;G.729a;G.729b, b:8, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-110, a:G.726-16;G.728, b:16, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-70, a:G.726-24, b:24, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:10-50, a:G.726-32, b:32, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-270, a:G.723.1-H;G.723;G.723.1a-H, b:6, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
L: p:30-330, a:G.723.1-L;G.723.1a-L, b:5, e:on, gc:1, s:on, t:10, r:g, nt:IN;ATM, v:L;G;D;T;H
M: sendonly, recvonly, sendrecv, inactive, loopback, conttest, data, netwloop, netwtest
<---
*Dec 25 13:13:47.036: MGCP Packet received from 172.26.4.2:2427--->
200 257951731
<---
*Dec 25 13:13:48.004: MGCP Packet sent to 172.26.4.2:2427--->
RSIP 257951728 *@store179.super-pharm.co.il MGCP 0.1
RM: restart
<---
*Dec 25 13:13:48.036: MGCP Packet received from 172.26.4.2:2427--->
200 257951728
<---
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#
store179(config)#u all
^
% Invalid input detected at '^' marker.
store179(config)#exit
store179#
*Dec 25 13:14:02.016: MGCP Packet sent to 172.26.4.2:2427--->
NTFY 257951732 *@store179.super-pharm.co.il MGCP 0.1
X: 0
O:
<---
*Dec 25 13:14:02.032: MGCP Packet received from 172.26.4.2:2427--->
200 257951732
it's not possiable to do the other debugs they stuck the router -
Restricting FXS ports to internal calls only
Hi,
I have recently intalled Call Manager 8.5.1 with a H323 Gateway. On the gateway, I have a number of FXS ports for lobby phones. Is there a way I can restrict these phones to allow only internal calls only? Do I need to use COR lists like in Call Manager express or is there a more practical way?
Thanks,
DerekHi Derek,
It sounds like these FXS ports are NOT registered to CUCM 8.5.1? If they aren't, then yes COR lists is the most pratical way to do this. You could do a "connection plar xxxx" to a receptionist extension and her her/him forward the calls to the correct extension. -
MGCP FXS ports requires a license in CUCM9
Hello!
I am connecting Some analoge phones to VG350 FXS ports which is configured as a MGCP Gateway in CUCM. I beleive MGCP did not requires any license for it. Can some confirm this ? is there any Cisco doc on it ?
Thanks & Regards,Hi Sambit,
Technically u are correct but legally I think u would be requiring license.
even the ordering guide says Analog devices are supported with Essential USer license and must be purchased through UCL.
http://www.cisco.com/web/partners/downloads/partner/WWChannels/technology/ipc/downloads/finalcopy.pdf
regds,
aman -
Hi,
We are running VoIPovFR to a remote location, which has 2 x 4FXS/DID module installed into a C2621XM chassis. We are using IOS c2600-is-mz.122-15.
Out of the 8 ports, two continually go off-hook, FXSLS_WAIT_OFFHOOK before finally going into a FXSLS_PARK state. I have moved the cabling and the error occurs on which ever port the two lines plugs into.
Has anyone ever see this before. To my mind it looks like a cabling issue?
Any ideas?
ThanksTry wiring all FXS ports like this
FXS PORT 0 RJ11 3-----------------------A ANALOGUE
FXS PORT 0 RJ11 4-----------------------B PHONE
FXS PORT 1 RJ11 3-----------------------A ANALOGUE
FXS PORT 1 RJ11 4-----------------------B PHONE
FXS PORT 2 RJ11 3-----------------------A ANALOGUE
FXS PORT 2 RJ11 4-----------------------B PHONE
FXS PORT 3 RJ11 3-----------------------A ANALOGUE
FXS PORT 3 RJ11 4-----------------------B PHONE
Ensure that all other wires are left disconnected -
EFTPOS No Response X0 Using FXS Port
Hi All,
Trying to get an EFTPOS machine working connected into an FXS Port using SCCP/STCAPP Protocol for call control.
The port is registered in CUCM, I can connect an analogue phone to the port and successfully call the Bank's 1800 Number etc, I can make other external calls no problem.
When I try the EFTPOS Machine, the call setup runs through normally and I see the call is then in a connected state. Approx about 10 or seconds later the call is cleared by the local device with an 0x8090 code Normal Clearing. The call is then disconnected and released as per any other call.
The EFTPOS Machine prints a error for "Declined No Response X0"
I have attached the following debugs.
debug isdn q931
debug voip vtsp all
debug vop ccapi inout
debug voip rtp session named-event
Calling Number is 0245604627
Called Number is 1800509183
General environment setup is as follows.
EFTPOS connect to FXS Port -> Registered to CUCM (9.1.2) -> SIP Trunk -> IOS 15.x -> ISDN Pri.
Any feedback i smuch appreciated.
BenNot so sure if the service code being utilize by the FXS is the same as what is mentioned in VSA.Then again, the manual says "dial the corresponding * code on the client station" and if you look at an SPA9xx phone, it has the following codes defined for call park and call unpark code.
*38
*39 -
CLID presentation fails on FXS port
i have a mgcp gateway with a nm-hd-2v , and the modules vic2-2fxo ,vic2-2fxs
The CLID of the external call is presented normally on my fxo port and displayed on the IP (soft-)phones.
I dont see the nr getting presented on the FXS port when i debug.
Called number and calling nr remains empty.
I see a calling nr when i do a csim start <exention>
caller-id enable is configured on the fxs port configuration at the gateway.
tried several type of caller-id alerting methodes without success.
When connecting the same phone on the pstn, i get the clid normally so it is something in the configuration
regardsHi,
Yes - you are correct. Looked at this one too quickly.
You will want to make sure the CPTONE defined on the port is for the country the phone is manufactured for, and that the voice-pport has the 'caller-id enable' command.
If those are both correct, and I'm guessing that they are since some caller-id works, then you need to inspect the gateways that take the calls to begin with.
Do you have caller-id trouble for internal calls also?
How do these calls come into your network?
hth,
nick -
Connection PLAR on FXS port 2821
I have an anlog phone that is located by the main gate. The phone has been extended and terminated into an FXS port on a 2821 router. I am trying to configure a connect PLAR on he FXS port, so that when the phone goes off-hook it dials an internal VoIP extension.
I am not having any luck. Any help would be appreciated. My config is below:
voice-port 1/0/5
timing hookflash-in 50 0
connection plar 220005
description North gate
caller-id enable
dial-peer voice 220005 pots
destination-pattern 220005
port 1/0/5
dial-peer voice 100 voip
preference 1
destination-pattern 220...
modem passthrough nse codec g711ulaw
session target dns:CallAgent01
voice-class codec 1
voice-class h323 1
dtmf-relay h245-alphanumeric
no vad
Thanks!!
JaimeYosh - do I need to remove dial-peer voice 220005 pots for the PLAR to work correctly?
Thanks,
Jaime
Maybe you are looking for
-
Error exporting BI Report to Excel
Hi All, We are experiencing strange error, while exporting to Excel. We have a sales report which extract data for 3 regions US, ASIA, EUROPE. The amount of data for particular month is as follows: No Of Rows File
-
can anybody tell me why i get the famous cant open core dll? in acrobat?
-
Fluxbox-like tabs in openbox via tool ?
Hi! I am happy fluxbox user. Now I am tempted to switch to openbox, BUT I would miss tabs (=auto-grouped windows with tab ower group, like fluxbox - see http://fluxbox.sourceforge.net/features/tabs.php). I would like not to repeat things said elsewhe
-
When installing Acrobat Pro, I receive these errors: EAccess violation in module AcrobatPro_11_Web_WWMUI.exe at 0001B7D6 access violation at address 0041B7D6 in module AcrobatPro_11_Web_WWMUI.exe Read of access 00000008 The program will not run. Help
-
hi,, i am pursuing a course in advance software technologies and have to do a project for four months.. i want to do a thesis , can you please suggest me some topics on which i can do thesis, considering that i only am familiar with ABAP.. please obl