Phone USB disconnect not detected

On my one PC, PC Suite does not detect when I disconnect my E51 phone from the USB cable in PC Sync mode.
This one happens on this specific PC, so it must be a setup problem there.
I am running PC suite 6.85.14.1 on WinXP SP2 patched up to date. No problem on another box with same motherboard and software using the same phone.
If I connect in data transfer mode, I use the "safely remove hardware" function of WinXP before I disconnect and all is fine. This is not available in PC Suite mode.
If I unplug the cable from the phone in PC suite mode, PC Suite does not detect that the phone is disconnected, no matter how long I wait.
After this, the whole USB system seems to be confused. No other USB devices are detected when plugged into any other USB port. After reboot all is fine again.
I guess this is a Windows problem rather than a PC suite problem.
Any idea what is going wrong and how to correct this?

i had other similar problem with usb devices, maybe when we use more usb devices could be a conflict on system, does exist a tool that clean up all old usb connection?
bye.

Similar Messages

[SOLVED]Usb drive not detected in kde

not appear in the notification, but in dmesg appear
5458.314319] usb 2-3: new high-speed USB device number 4 using ehci-pci
[ 5458.508037] usb-storage 2-3:1.0: USB Mass Storage device detected
[ 5458.508098] scsi12 : usb-storage 2-3:1.0
[ 5458.508149] usbcore: registered new interface driver usb-storage
[ 5459.585989] scsi 12:0:0:0: Direct-Access USB DISK Pro PMAP PQ: 0 ANSI: 4
[ 5460.612052] sd 12:0:0:0: [sdb] 31260672 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 5460.613431] sd 12:0:0:0: [sdb] Write Protect is off
[ 5460.613434] sd 12:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 5460.614802] sd 12:0:0:0: [sdb] No Caching mode page found
[ 5460.614805] sd 12:0:0:0: [sdb] Assuming drive cache: write through
[ 5460.619671] sd 12:0:0:0: [sdb] No Caching mode page found
[ 5460.619674] sd 12:0:0:0: [sdb] Assuming drive cache: write through
[ 5460.642643] sdb: sdb1
[ 5460.649748] sd 12:0:0:0: [sdb] No Caching mode page found
[ 5460.649751] sd 12:0:0:0: [sdb] Assuming drive cache: write through
[ 5460.649753] sd 12:0:0:0: [sdb] Attached SCSI removable disk
[ 5476.956859] ath5k: ath5k_hw_get_isr: ISR: 0x00000400 IMR: 0x00000000
[ 5613.844729] usb 2-3: USB disconnect, device number 4
[ 5616.296689] usb 2-3: new high-speed USB device number 5 using ehci-pci
[ 5616.425854] usb-storage 2-3:1.0: USB Mass Storage device detected
[ 5616.425903] scsi13 : usb-storage 2-3:1.0
[ 5617.501846] scsi 13:0:0:0: Direct-Access USB DISK Pro PMAP PQ: 0 ANSI: 4
[ 5618.534031] sd 13:0:0:0: [sdb] 31260672 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 5618.535398] sd 13:0:0:0: [sdb] Write Protect is off
[ 5618.535401] sd 13:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 5618.536784] sd 13:0:0:0: [sdb] No Caching mode page found
[ 5618.536790] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[ 5618.541762] sd 13:0:0:0: [sdb] No Caching mode page found
[ 5618.541765] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[ 5618.564608] sdb: sdb1
[ 5618.571842] sd 13:0:0:0: [sdb] No Caching mode page found
[ 5618.571845] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[ 5618.571847] sd 13:0:0:0: [sdb] Attached SCSI removable disk
uname -a
Linux tarro 3.13.5-1-ARCH #1 SMP PREEMPT Sun Feb 23 00:25:24 CET 2014 x86_64 GNU/Linux
cat /etc/group
root:x:0:root
bin:x:1:root,bin,daemon
daemon:x:2:root,bin,daemon
sys:x:3:root,bin
adm:x:4:root,daemon
tty:x:5:
disk:x:6:root,darkmind
lp:x:7:daemon,darkmind
mem:x:8:
kmem:x:9:
wheel:x:10:root,darkmind,pct
ftp:x:11:
mail:x:12:
uucp:x:14:
log:x:19:root
utmp:x:20:
locate:x:21:
rfkill:x:24:
smmsp:x:25:
http:x:33:
games:x:50:darkmind
lock:x:54:
uuidd:x:68:
dbus:x:81:
network:x:90:darkmind,pct
video:x:91:darkmind,pct
audio:x:92:darkmind,pct
optical:x:93:pct,darkmind
floppy:x:94:
storage:x:95:darkmind
scanner:x:96:pct,darkmind
power:x:98:
nobody:x:99:
users:x:100:pct
systemd-journal:x:190:
polkitd:x:102:
transmission:x:169:
avahi:x:84:
usbmux:x:140:darkmind
ntp:x:87:
mysql:x:89:
kdm:x:135:
git:x:999:
pct:x:1001:
(i'm darkmind)
somebody help?
Last edited by dunkles (2014-02-25 22:50:53)

ewaller wrote:I am not sure what that means. Are you expecting a pop up notification in KDE?
yes
ewaller wrote:Does Dolphin show the volumes?
not show the volumes, nothing happens when plug a usb drive
ewaller wrote:Do you have udisks installed? How about udisks2?
yes

USB devices not detected in VMware [SOLVED; Using Virtualbox instead]

I am running Arch as a host and XP on VMWare workstation 7. My primary purpose of installing XP on VMWare was to use my edit my Line6 POD (behaves as a usb sound card) and get my USB TV Tuner box to work. The big problem that I am facing is that VMWare is not detecting any USB device (not even my USB Hard Drive).
I have the usb controller installed.
Any suggestions?
Last edited by devadittya (2009-11-24 20:04:45)

I don't know vmware but with other virtual machines there is often a configuration option whether usb drives should be automatically mounted or not. Sometimes automounting also only works if the vm has the focus, i.e. is the active window.

Hp Pavilion DV4-1235ee No sound & Usb port not detecting.

In my laptop Hp Pavilion dv4-1235ee there is no sound coming from the internal speakers. If I connect external speaker its works fine. Usb port is not detecting now. any help will be appreciated.

What is the current Operating system on your notebook? I suspect we have issue with internal speaker on hand...but would like to reinstall the Audio Driver and check...
Again for the USB, we can try and install Chipset driver and check...
Although I am an HP employee, I am speaking for myself and not for HP.
Make it easier for other people to find solutions, by marking my answer with 'Accept as Solution', if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

X220: external USB keyboard not detected in BIOS

Hi!
I use an external USB keyboard attached to the port replicator of my X220. When Windows is booted the keyboard works without any problems. But I cannot use the keyboard pre-boot, e.g. to enter the HDD password after starting up, to configure the BIOS, etc.
I tried all USB ports both of the port replicator and the X220. The keyboard is still not detected by the BIOS (Version 1.20) and there are no BIOS options to enable "USB keyboard support".
Has anyone experienced similar problems? Are there any solutions to get the keyboard detected by the BIOS?
Thank you for your support!

@beastiesoft and earthartja,
If I am not mistaken, we are discussing this on the T series thread. Check here.
http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T420-Not-recognizing-keyboard-before-OS-loa...
@someotherguy,
Drop you an email on this.
//JameZ
Check out the Community Knowledge Base for hints and tips.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
X240 | 8GB RAM | 512GB Samsung SSD

USB Port not detecting device

My usb port on the side of the pc both are not detecting any device. How to fix it?

A good place to start troubleshooting is this HP document, Troubleshooting USB Connections (Windows 7).
If you don't have Windows 7 or if you have further problems, please to provide more information when you post again. The more information you provide, the more likely it is that you'll find someone here to help you.
Welcome to the forum,
GeorgeFN
GeorgeFN
I work on behalf of HP.

[Solved]Usb Pendrive not detected

Hello, I have a xfce4 desktop and when i insert my flashdrive its not detected in thunar.
I have ticked the options to "mount removable device when inserted" and "mount removable drivers when hot-plugged".
What do I have to do to see my pendrive in Thunar!.
Thanks for reading
Last edited by Jean3799 (2014-06-24 06:00:36)

Make sure gvfs is installed.
sudo pacman -S gvfs
Read in the wiki here and here.

I phone cable is not detecting on any of my laptop ports or on the external charger

Hi,
I bought my I phone 5 around 3 months back and it was perfect till it stopped charging and as a result the cable is not being detected on my laptop or the external charger... Any suggestions?

Either the cable is bad and needs to be replaced, or there is a problem with the iPhone.
Do you have access to another cable that is known good - used by a friend, family member, neighbor, or someone you work with to rule in or out a problem with the existing cable?
If determined to be a problem with the existing cable, all package contents included with the iPhone are under the iPhone's one year warranty.

Airport Extreme and USB HD not detected in Vista but work in OSX

I have a hard drive and a printer connected to a USB hub that's hooked up to my Airport Extreme. USB hub is a good one, powered. Everything works like it should on the two Macs I have. Airport Utility detects everything fine, all works well. Great.
On my Vista PC, which is my main computer, being by far the most powerful, I have Airport Utility installed so that I can have access to my network hard drive. Weird thing is that it gets detected sometimes, and sometimes it doesn't. When I re-install Airport Utility, everything works for that session. After a reboot it may or may not work. Usually it stops working all together after 2 or 3 reboots.
Internet access works all the time, mind you, as well as printing to my printer that's connected to the extreme. Just no base station detected in Airport Utility and no hard drive access, because the base station isn't available.
Thing to note, my computer goes through a gigabit switch, D-Link DGS-2205 to get to the airport extreme. I have an iMac that also goes through that switch, but doesn't have these problems.
Any ideas what to do? I'm sick of re-installing Airport Utility every couple days.

Nobody had a similar problem? Re-running Airport Utility installer again and Repairing the current installation fixes it for a short period of time, but the same problem comes back after about 3 reboots. Any ideas?

Windows XP running on iMac, USB Printer not detected on Windows

Hi all,
I'm pretty sure this is not a Mac issue, however I've been trying to understand this problem and I didn't find a proper solution, maybe some of you can help with that.
The situation is:
iMac running Mac OS X 10.4.10 working fine with a Xerox Printer 8550 connected with a USB cable, however, in the same system my colleague has a Windows XP installed with BootCamp, the problem is that Windows Xp cannot detect the USB printer, have you heard anything like that before?
Any help is welcome.
Thanks in advance.
Kind Regards
Alatryste

should be only driver problem?
http://www.support.xerox.com/go/results.asp?Xlang=enUS&XCntry=USA&prodID=85008550&ripId=&Xtype=download

HP USB Drive not detected

I bought a new 16GB HP USB Drive a day ago. The drive is not recognised by my mac. When I plug the drive in nothing happens.
- other USB drives work as normal
- I tried both USB ports (i.e. it's not a mac hardware issue)
- the USB drive works with my PC
I don't see the USB drive in the disc utilities option. Can anyone suggest what I should do next?
Thanks in advance
Ian

BijanMacLover wrote:
The following worked for me like a charm but you have to try it at your own risk.
1- Using Bootcamp switch to Windows. It will detect your memory flash HP 16 GB.
2- Click on my Computer, then right click on HP 16GB icon
3- Select Format
4- Format your Flash selecting FAT32
5- When finished reboot back to MAC and you are ready to go.
Hope it works for all.
You don't need to boot into Windows, you can format the drive using Disk Utility in OSX

Ethernet to USB is not detected

I have recently bought a Ethernet to USB converter. When I connect it to my laptop it does not get connected ,It is getting detected and it is shown in PC settings>Devices.When I troubleshoot it,It shows that the drivers are not properly installed.
How to install the proper drivers? Hoping for a early reply
prudhvi

Try get the drivers from the vendors webpage. Furthermore, look if the NIC is supported by your Operating System
Best Regards,
Jesper Vindum, Denmark
Systems Administrator
Help the forum: Monitor(alert) your threads and vote helpful replies or mark them as answer, if it helps solving your problem.

Logitech USB headset not detected

When I run lsusb | grep Headset, it shows that the usb headset is plugged in(grep audio did not work).
Sample output:
Bus 002 Device 005: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset
But here's the problem, when I execute aplay -l, it gives me no sound cards found, though I even have a intel intergrated audio sound card.
I have gnome installed, so it uses pulseaudio, so I can't use alsamixer, but is I go into sound settings, it only says dummy output.
Other things to note:
- Do not have gnome-extra installed
- Have extra gst media codects
Thanks in advance,
Ahad

Hi daveodonoghue,
May i know does your machine works with other USB device? Please try update BIOS. If problem remain, please contact local lenovo for further assistance.
Worldwide Support Center phone list for ThinkPad, ThinkCentre and ThinkStation systems
http://support.lenovo.com/en_US/detail.page?DocID=HT036550
BIOS Update Utility for Windows 7 (32-bit, 64-bit), Vista (32-bit, 64-bit), XP - ThinkPad T420, T420i
http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS018785
Fred
T61 + X201i

USB Devices Not Detected and High CPU Usage

Hello, I'm using arch on a Dell 1720 laptop.
I have some weird issues involving detection of USB devices.
When the laptop is on battery and I plug in a USB mouse the power flickers on and flickers off again; nothing in the logs/dmesg.
If I then connect the AC adapter the reconnect the mouse, the same happens, except the CPU usage hits 87%+ on one core.
Running
sudo rmmod ehci_hcd
solves the problem; the CPU usage drops and the mouse gets detected.
Subsequent attempts to hotplug USB devices does nothing, no high CPU and no Power.
Rebooting the computer is the only way to use USB devices at the moment.
usb-autosuspend is disabled in laptop-mode.
uname -a:
Linux MatSalleh 2.6.39-ck #1 SMP PREEMPT Sun Jun 5 18:30:30 EDT 2011 x86_64 Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz GenuineIntel GNU/Linux
The same happens with the stock kernel too
My kernel line in grub:
kernel /vmlinuz26-ck root=/dev/sda3 elevator=bfq ro resume=/dev/sda2
Any ideas?
Thanks,
Chris.

lilsirecho wrote:Perhaps the USB connector is damaged, causing excess power drain suggesting that the current limiter isn't functioning.
I highly doubt it's that, it was working fine on ubuntu just days before...
tydell wrote:I had similar problem with USB pendrive, it wasn't detected and it makes high cpu usage. It was problem with ehci_hcd module
This one helps me to solve this problem
My USB devices don't even get detected, so that script won't work.
Last night I hibernated my computer after not using any USB devices, on resume, my CPU usage was 100%, removing the ehci_hcd module fixed it.
Any more ideas?
I'm tempted to build a vanilla kernel...

I-7565 USB DNET not detecting all DNET devices

hello,
I have a USB Devicenet device called ICP DAS I-7565 DNM.
I have connected it to a machine that has 9 devices but it always only detects 6 of them, i tried it on several machines but still the same result.
i also have a NI PCI and PXI 8461 cards that detect all 9 devices.
simplewho.exe also detected all 9 devices.
what could be wrong, how can i troubleshoot the USB device?
Please help

Hi freemason
I wonder if the 3 devices not been detected are always the same, or if this is more lika a "maximum number of devices to detect" issue. Have you tried to remove some of the detected devices to see if another one is detected?
Maybe you can contact the manufacturer of the I-7565-DNM to confirm if all the 9 devices you are trying to detect are supported by it.
WenR

Phone USB disconnect not detected

Similar Messages

Maybe you are looking for