Phonon settings reset each login.

This might not be a big deal, but it's really annoying.
Each time I log into KDE, I have to go to the "Audio Hardware Setup" tab and set it to use my sound card instead of my graphics card.
I don't even know why my graphics card is there.
Is there a way to save phonon's settings?

Further on this, the latest login today resulted in the mouse scroll setting being retained but not anything else.
Also I didn't get the Apple ID prompt.
Not sure what this means.
Cheers
Tim

Similar Messages

System preferences reset each login

Hi,
(iMac 2009) Just installed Mountain Lion, full refomat, set up a new admin account, then used migration assistant from a dmg backup to move everything.
Everything restored - apps, users, etc - all usable.
I want to use the account that was previously my admin account as my "normal" account as that is the one with all the mail, music, etc.
Logging in with the account is all good. I start changing things to my liking - change my desktop picture to something pretty, remove the question mark apps from the Dock, remove the "natural" scrolling for the mouse, etc - everything good while in that session.
I logout and then log back in as the same user - everything is reset back - question marks back, old ugly desktop picture, natural mouse scrolling, etc.
First clue is each time I login, I'm prompted with "Apple ID needed" and asked about iCloud connection. Again.
Logging in with the newly created admin user does not cause this problem and date/time and other parameters are all ok.
Maybe it is something with permissions, perhaps because the account is the "old" admin account from Snow Leopard? I'm not getting any errors that I can see.
I thought it was my problem when running the update/migration the first time, so I reformatted, reinstalled and re-migrated to the same result.
Any thoughts or suggestions? I'm tearing my hair out here (and I don't have much left!).
Cheers
Tim

Further on this, the latest login today resulted in the mouse scroll setting being retained but not anything else.
Also I didn't get the Apple ID prompt.
Not sure what this means.
Cheers
Tim

I had to reset my Apple password and now my iTunes and iCloud passwords no longer work. How do I get them linked again and under the same password. I've tried my new password on each login screen and it isn't accepted.

I had to reset my Apple password and now my iTunes and iCloud passwords no longer work. How do I get them linked again and under the same password. I've tried my new password on each login screen and it isn't accepted.

Hi skippy2012trev,
Welcome to the Apple Support Communities!
I understand that you updated your Apple Id and password but now you are being prompted for the old information in iCloud. You are on the right track by changing the Apple ID back to the previous email address temporarily so that you can sign out. You should not need to verify the email address. After you edit the Apple ID back to the old email address and then sign out of iCloud on your iPhone, edit the Apple ID back to the address you would currently like to use. There is no need to change the password again, only the email address, unless you prefer to update the password again.
If you're asked for the password to your previous Apple ID when signing out of iCloud - Apple Support
Change your Apple ID temporarily
If signing out and back in to iMessage or FaceTime didn't help, try these steps:
Change your Apple ID to the Apple ID you used previously. You shouldn't need to verify the email address.
Tap Settings > iCloud. Complete these steps only if the Find My [Device] setting is turned on:
Scroll down and tap Sign Out, then tap Sign Out to confirm. If you're using iOS 7 or earlier, tap Delete Account, then tap Delete to confirm.
Tap Keep on My [Device] or Delete from My [Device]. In either case, your data remains in iCloud and will be updated on your device when you sign in to iCloud again.
Enter the password for your previous Apple ID.
Change your Apple ID to the new email address that you want to use. You'll need to verify the email address.
Return to Settings > iCloud and sign in with your new Apple ID.
Cheers,
Joe

ColdFusion Builder 3 Settings Reset on Restart

I've downloaded the ColdFusion Builder 3 trial and am experiencing some odd and very annoying behavior.
I've customized some code editor text font and color settings. I've added an entry to the CF Servers panel for an instance of ColdFusion 10 running inside a VMWare virtual server on my laptop.
When I restart Eclipse, all the code customizations I've made are reverted back to the default install settings and the entry in my CF Servers panel is gone.
I've been an IntelliJ user for well over a year, but in doing much more cfscript-based development the CF Plugin for IntelliJ is proving to be a hindrance so I thought I'd give CFB 3 a try and see if there were any improvements over CFB 2. However, I can't take this kind of behavior. Hopefully someone can give me a setting or someone else has seen this before and can give me an idea of where to start looking.
I have CF Builder installed as a plugin into Eclipse Kepler 64-bit for Mac. I added the CF Builder update site and have updated to CF Builder 3.0.0.290000. I also previously installed as the standalone version with no additional plugins and experienced the same behavior.
Anyone have any ideas?
Thanks,
Dan

Milan...
My apologies for taking so long to get back to this. I just did some testing tonight of your instructions as well as those by Kaif above.
Firstly, I installed ColdFusion 10 locally on my Mac. I added the local server to the CF Servers panel successfully. After restarting Eclipse, the localhost entry remained in the CF Server panel.
Secondly, I followed your instructions to make a new profile and make my font/coloring customizations in it. I restarted Eclipse and my font and color selections were maintained (through 3 restarts). I noted that my newly created profile was selected in Preferences after each restart.
I then added a remote CF 10 server to the CF Servers panel successfully (as noted by the panel telling me that the server was running and being able to launch the CF Admin from within Eclipse). At this point there were 2 entries in my CF Server panel--localhost and the one remote server that lives inside my VM. I restarted Eclipse and when it came back up, only the localhost server remained. I might add that the VM has ColdFusion 10 installed in "multi-instance" mode and that the remote server instance that I added to the CF Servers panel was one of 4 CF instances configured and running inside the VM.
All the while, my font and color customizations have remained the way I set them.
So, it appears as though we're down to just one bug relating to remote server registrations in the CF Servers panel.
I saw that another user was reporting something similar in this thread: ColdFusion Builder 3 RDS and Remove Server settings reset on each restart so apparently it's not just me.
Thanks to you and everyone else for all the ideas and troubleshooting help thus far. At least at this point I think I might be able to use this for day-to-day coding, even though I really want the remote server system to work correctly so I can use the step debugger feature again.
Dan

My tab default is1.25 which is too big for the A5 document I'm working on, how do I change the default tab so that I don't have to reset each individual line?

My tab default is1.25 which is too big for the A5 document I'm working on, how do I change the default tab so that I don't have to reset each individual line?

Hi Hannah,
Inspector > Text > Tabs Button > Tab Settings > Default Tabs.
To set a tab stop on the go, click in the ruler.
If you can't see the ruler, Menu > View > Show Rulers.
To set tab stops for lines (paragraphs) you have already typed, select those paragraphs and set them all at once.
Also, have a look at Menu > Pages > Preferences > Rulers.
Regards,
Ian.

E4200 - Has to be Reset each few days.

my E4200 v1 has to be reset each few days is that normal? Seems not

Could you please share the exact issue that you are facing with the Router? Does it looses its connectivity every now and then? If YES, then it happens for both wired and wireless connection?
You should be able to get a good connection without having to be in the same room, but you do need to be in range of the router, and there may be interference in your home or neighborhood. You can adjust your settings to improve your signal. If you used the Cisco Connect installation disk, then open up the Cisco Connect software on your computer. Click on “Router setting” window, and then click on the “Advanced settings” button. That will opened the Router Setup page, then click on Wireless Tab and make the following adjustments:
Channel Settings of 2.4 GHz, set Channel Width to 20 MHz only and Channel to 6, 9, or 11.
You can even try lowering the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your router's main/ basic setup page).
If you configured the Router manually, open up the browser and type 192.168.1.1 in your address bar. That will open the Router setup page and you can set the channel as above.
You should also make sure you upgrade the drivers for the WLAN card on your laptop computers

Retaining individual icloud settings with separate logins.

My wife and I are set up as separate users with separate logins on our imac. Will the imac remember our individual icloud settings whenever we each login in? When icloud was 1st set-up it was done so under my login using my apple ID. Having now read more about icloud it seems very restrictive on how to keep our details separate. Its not clear to me how to resolve my issue from the discussions had so far.
What I'm trying to do:
I want to set up icloud so that when we each login to our imac under our separate accounts the imac will remember our individual icloud settings. We don't want share our apple ID or iCloud accounts.
Can this be done? Will the imac remember our individual settings? Our OS is Mountain Lion 10.8.5.
Any assistance on clarifying this issue for me would be great.
Thanks.

My wife and I are set up as separate users with separate logins on our imac.
Yes,
each of your separate useraccounts will store the settings you are making in the System Preferences panels for your individual account, including what you are setting up in your iCloud panel.
Regards
Léonie

Spotlight index lost after each login

Hello people,
I've got a very confusing thing going on with Spotlight on my mac.
After each login, Spotlight looses its index and I can't my files.
I have tried solving this problem with the app IceClean, using "sudo mdutil -i on /", dragging and remvoing something into the privacy tab in Spotlight's preferences and some other tips and tricks I got from this forum, but nothing worked.
The odd thing is, Spotlight finds the files, but only after some time. My guess it's restores the index or re-indexes everything. Yet that doesn't help since it gets deleted after the next login.
I am very confused right now. No solution seems to work I thought maybe you guys know some answer to that problem.
Any tip and help is greatly appreciated.
Best regards
Martin
I am using a Macbook Pro, Snow Leopard v10.6.6 (10J567)

No one?

How to reset my login password for macbook air

How can I reset my login password for my laptop? For some weird reason, my login password no longer works. I now have to get on by logging into guest and then clicking on my username.

Reset Password using Recovery HD
OS X 10.7 Lion /10.8 Mountain Lion
Follow the instructions in the first and third boxes.
http://pondini.org/OSX/Password.html

How do I save my Home sharing details on Apple TV. It resets each time I leave COMPUTER ...

How do I save my Home sharing details on Apple TV. It resets each time I leave COMPUTER ...

Welcome to the Apple community.
What makes you think it is resetting, are you sure it is not simply disconnecting.

When trying to reset my login / password, text in red says not connected to internet please verify connection, when the macbook air IS connected to wifi.

cannot reset forgotten login password.

You don't need to be connected to the Internet to reset the password.
Note: If you've activated FileVault, this procedure doesn't apply. Follow instead these instructions.
Start up in Recovery mode. When the OS X Utilities window appears, select
Utilities ▹ Terminal
from the menu bar at the top of the screen—not from any of the items in the OS X Utilities window.
In the window that opens, type this:
resetp
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window opens. Close the Terminal window to get it out of the way.
Select the startup volume ("Macintosh HD," unless you gave it a different name) if not already selected. You won't be able to do this if FileVault is active.
Select your username from the menu labeled Select the user account if not already selected.
Follow the prompts to reset the password. It's safest to choose a password that includes only the characters a-z, A-Z, and 0-9.
Select
 ▹ Restart
from the menu bar.
You should now be able to log in with the new password, but the Keychain will be reset (empty.) If you've forgotten the Keychain password (which is ordinarily the same as the login password), there's no way to recover it.

Since updating to iOS 6, my 4th gen iPod touch, and my 3rd gen iPad has sound in and out. Sometimes it's on, and then all of a sudden, no sound. I've tried everything from restarting to fully resetting each one starting fresh, but nothing. Please help.

Since updating to iOS 6, my 4th gen iPod touch, and my 3rd gen iPad has sound in and out. Sometimes it's on, and then all of a sudden, no sound. I've tried everything from restarting to fully resetting each one starting fresh, but nothing. Please help.

I have exactly the same problem. I have tried almost everything and I am nowhere near an Apple shop as I am working in Africa.
Did you manage to find a solution? Help please if possible. Regards Az

Settings reset code?

Does anyone know the code for a total settings reset on the N95 please

It must only be in a few thousand posts on these forums so pretty obscure.
Revert to factory defaults: *#7780#
Soft reset: *#7370#
Hard reset: power off. Hold down '3', '*' and 'call'. Power on with those buttons pressed. Release them when the phone shows the nokia "handshake" logo or the language selection screen.
Do a backup first - these procedures will wipe your settings at least, and the resets will wipe everything in the phone's central memory (but not the content of the memory card).
Was this post helpful? If so, please click on the white "Kudos!" star below. Thank you!

Settings reset when Comp resta

Since downloading 2.8.0004, whenever I restart my computer ALL my sound settings reset to stock settings. (Volume settings, Mic settings, etc). So everytime I restart my computer I need to go through all my settings and put them back where I want them.... EVERYTIME. I tried to figure it out on my own, but I'm at my wits end.
Any help you guys could give me would be very much appreciated.
System Specs
SoundBlaster X-Fi ExtremeGamer
Asus P5N-D
Intel Core2 Quad CPU Q9300
Nvidia EVGA 8800gtx
Vista Home Premium x64
4gb Mushkin Extreme RAM
Anything else you need, please let me know.

Hello Nafets727,
You might want to check this thread.

HT4623 i reset my login two days ago, now I can't remember it and my Ipad is disable and I was told to connect to iTunes

I reset my login on my ipad two days ago, today I can't remember what I changed it too. My Ipad is disabled and I was told to connect to ITunes

1. Turn off iPad. Press and hold the Sleep/Wake button for a few seconds until the red slider appears, slide to turn off.
2. Connect USB cable to computer
3. Press and hold the Home button down and connect the docking end of cable to iPad
4. Continue holding the Home button until you see the "Connect To iTune" screen
5. Release the Home button
6. Open iTune (make sure you have the newest version of iTune)
7. You should see "iTunes has detected an iPad in recovery mode"
8. Use iTune to restore iPad
Note: You need to be patient and repeat the above many times to recover your iPad. Data will be lost.

Phonon settings reset each login.

Similar Messages

Maybe you are looking for