Photo registration problems

I am printing photographs on an HP A516 and the pictures are no registering correctly. They print with a border of about 1/8 inch on the right side and the bottom of the picture and no border on the left side and top and it looks like some of the left side of the photo is getting cut off. I've tried everything I can think of in the printer settings to correct this but have had no luck changing this. Any ideas????   Thanks for the help.    Jerry

Hello Jerry,
I saw your post on the issue you are having printing photo's correctly on your Photosmart A516 printer. I understand you have tried to change the print settings, to no avail. I am going to recommend trying a few things.
First of all, lets see if the issue is hardware related by printing a test page to see if the same results happen:
Press the left arrow button or the right arrow button to open the Printer menu.
Use the arrow buttons to highlight Tools, and then press the OK button to select it.
Use the arrow buttons to highlight Print test page, and then press the OK button to select it.
Press the OK button to print the test page.
If the defects show on the printers test page, the issue is hardware related. If not, the issue is software related.
If the test page has the defect, Reset your Printer.
If the test page prints fine, lets move on to uninstalling the driver and reinstalling it. You will have to select which operating system you are working with.
Here are the instructions for how to Uninstall the Printer Software.
Restart your computer fully before reinstalling.
Reinstall by clicking on this link: HP Photosmart A516 Compact Photo Printer Drivers.
Try printing again from your computer.
I hope this helps.
Good luck
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Similar Messages

  • Photo sync problem with Windows Vista?

    I did some searching and was wondering if there is a solution to the photo sync problem with Windows Vista. I have gone the route of changing some of my photos to bitmap files but this is was way too much work just to view on ipod. I like to email Apple but could not find a link to do so. As far as I know I have all updates but still the iPod does not sync photos. Is there an update to this that I am missing or am I stuck changing all my photos to .bmp files?
    Thanks,
    Dean.

    I checked out the article and not much help, thanks anyway.
    Would it make a difference if I purchased Adobe Photo Album or would I still be stuck with changing and saving files to .bmp extensions? I have Adobe Photoshop album starter but still have to change file extensions.
    If someone has a solution to this problem I would really be greatfull. I did contact Dell as this is a brand new computer and that was a wash. They did give me a number for Apple but of course I bought the iPod off of ebay and has no warranty on it so unless I pay a fee I'm not calling. It just blows my mind that Microsoft and Apple can't or won't come up with a fix. But I guess when Microsoft wants you to buy the Zune or Apple wants you to buy the overpriced Macintosh why would they waste time on having there products compatible with each other.
    Thanks.

  • ICloud photo stream problem

    Hi all - I really need your help. 
    My iPhoto '11 was working just fine until I upgraded it to 9.4.3.  I also just installed the recent system upgrade.  Now I am having multiple problems. It seems to stem from Photo Stream.  Activity Monitor shows that Photo Stream is using up gobs of CPU which is strange since it is supposed to not be working...
    In iPhoto, under the preferences, it shows that Photo Stream is not enabled.  If I check the box to turn it on, it just unchecks itself just as quickly.  But in the system preferences, it shows that Photo Stream is set up just fine.  Photo Stream is certainly not working.  And it seem to be totally screwing up iPhoto.  I have tried multiple iPhoto fix options (option alt fixes, restoring a backup library, uninstalling then reinstalling iPhoto) with no improvement.
    I'm not sure if the problem is coming from iPhoto or iCloud Photo Stream problems.  I am running OSX 10.8.4 on a 3.4 GHz Intel Core i7.
    Can anyone tell me what to do?  Thank you so much!

    Well Old Toad, I am stumped.
    I double checked and logged out of iCloud in both user accounts and made sure that PS was not enabled on either library.  Then I restarted the computer.  I went back to my main user account (second account set up = non administrator account) and to my main iPhoto library, logged into iCloud, tried turing on PS = did not work.
    If I do the exact same thing as above for a restore of a backup of my library = does not work.
    If I do the exact same thing above but log in with my first account (not my main one but it is the admin account on the computer) and access the test library I created = PS works just fine with no problem.
    It seems the problem with PS is limited to my primanry account (non-admin).  Do you think the admin privaledges difference between the two accounts could be the problem...?
    As always, I am thankful for your time and advice.

  • Element v.11 & 9 Photo mail problem with MS Outlook

    Looking for a fix:  Elements v.11 has a photo mail problem with Microsoft Outlook mail, even when Outlook is designated the defaul e-mail program in Windows internet.
    Is there a fix??  Thanks.

    I just posted the same problem and so I'll join this thread, hoping to see an answer to your question.  By the way, this PSE11 feature worked fine for me with Outlook 2007, but stopped working when I upgraded to Outlook 365.

  • IPad photo syncinc problem from Aperture

    Hi,
    I have a weird photo sync problem (Itunes 10.0.1, Aperture 3.0.3). Sometimes when I add a project to Aperture and an album under that project, I can't sync that to my ipad as Itunes doesn't see any pictures in the album.
    My Aperture library is huge so I'm not syncinc all of it, just selected photos. When I open iTunes, plug iPad in and go to iPad photos page, the project and the album appear in the list but if I check either one of those, the number on the right showing the number of photos in the album/project, is zero and nothing gets synced.
    Sometimes I've been able to fix this by restarting aperture and itunes. I've tried reprocessing previews (previews are 2560x2560) but it doesn't seem to help anymore.
    I've sort of localised the problem to Aperture. When I quit aperture, an information window "updating information for sharing previews" and a progress bar apperars. If this takes only a couple of seconds, then iTunes doesn't seem to detect any changes I've made. Sometimes it takes from 30 seconds to a minute and usually after that everything works.
    I tried to google this and others seem to have had similar problems but I didn't find a solution. Is there one?

    Hello,
    Try the troubleshooting help Aperture 3: Troubleshooting Basics
    Repairing the Aperture database and repairing permissions may help.
    If you have Aperture 2, go here. Aperture 2: Troubleshooting Basics
    Carolyn

  • I can't import my photos from my digital camera (Sony) this problem is recent. I have imported photos without  problem a problem before.

    I can't import my photos from my digital camera (Sony) to my iPad, this problem is recent. I have imported photos without  problem a problem before. Is this problem due to the IOS 6 update? How can I fix it?

    I have the same problem and apple needs to fix this - but in the mean time you can manually select the vertical photos then "import - import selected" and you can get your verticals. We need a better fix. THIS IS A BUG!

  • Cisco 9951 and cucme registration problem

    Hi Everybody
    I am trying to register a cisco 9951 phone to a cucme. The phone was previosly connected and registered to a cucm 9.1, now it must be registered in the cucme. The problem is that the status messages of the phone show that the phone has 9.3(2) firmware version and the cucme has 9.2(1) sip9951.9-2-2SR1-9.loads. It means that the phone has a higher version than the version in the router flash (cucme).
    I tryed tod download a newer cucme file-set but the last version available in cisco.com is the 10.0 and it has the sip9951.9-2-2SR1-9.loads file which is still older than the version in the phone. So the phone doesnt register.
    I follow step by step the instructions to configure and register ip sip phones to cucme. but I am stock.
    here is the configuration:voice register global
     mode cme
     source-address X.X.6.54 port 5060
     max-dn 10
     max-pool 5
     load 9951 sip9951.9-2-2SR1-9
     timezone 42
     tftp-path flash:
     create profile sync 0001184550824421
     camera
     video
    voice register dn  1
     number 4002
     name SIPPhone 2
    voice register pool  1
     id mac 501C.BFFC.DD85
     type 9951
     number 1 dn 1
     username nico password 12345
     description +571344002
     camera
     video
    tftp-server flash:Phones/9951/dkern9951.100609R2-9-2-2SR1-9.sebn alias dkern9951.100609R2-9-2-2SR1-9.sebn
    tftp-server flash:Phones/9951/kern9951.9-2-2SR1-9.sebn alias kern9951.9-2-2SR1-9.sebn
    tftp-server flash:Phones/9951/rootfs9951.9-2-2SR1-9.sebn alias rootfs9951.9-2-2SR1-9.sebn
    tftp-server flash:Phones/9951/sboot9951.031610R1-9-2-2SR1-9.sebn alias sboot9951.031610R1-9-2-2SR1-9.sebn
    tftp-server flash:Phones/9951/sip9951.9-2-2SR1-9.loads alias sip9951.9-2-2SR1-9.loads
    tftp-server flash:Phones/9951/skern9951.022809R2-9-2-2SR1-9.sebn alias skern9951.022809R2-9-2-2SR1-9.sebn
    the status mesages on the phone say:
    Upgrade rejected: HW compat failure. Must use 9.3(2) or later release on this phone
    Error updating locale
    It still shows:
    File not found United_States/g4tones.xml
    File not found SIP_English_United_States/ik-sip.jar
    Those files tha the phone doesnt find are in the cucm 9.1. I tryed to put them in the flash and configured the tftp-server command and I also downloaded the 9.3(2) from the cucm and copied to the router flash, but it still has registrations problems.
    I also tryed to reset the phone to the factory defaults but this sequence with # key and 123456789*0# doesnt aply to sip phones and the procedure of the following link still doesnt work:
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cuipph/9971_9951_8961/10_0/english/adminguide/P567_BK_A27DADFD_00_adminguide-8961-9951-9971-10_0/P567_BK_A27DADFD_00_adminguide-8961-9951-9971-10_0_chapter_010100.html
    Please help me with this issue.
    Best regards

    Hi Sayeed,
    Can you please send accross SIP messages when phone is trying to register with CME ?
    Thanks
    Manish

  • Photo adding problem iphone 4g

    photo add problem from latest itues to iphone 4g  6.0.1

    Read the article from which the thread was created and follow the troubleshooting steps provided.

  • Photo tray problem

    The message on the screen  shows Photo tray Problem  -Reinset or lower photo tray

    Hello Wildo44,
    Welcome to the HP Forums!
    I understand you're receiving a message stating "Photo Tray Problem". I will do my best to assist you! What type of printer do you have? Click here to find out: Model Number.
    I would recommend following this entire HP document on The 'Photo Tray Problem' Message Displays on the Control Panel. Please post your results, as I will be looking forward to hearing from you.
    Have a great day!
    I worked on behalf of HP.

  • Photoshop/Elements to Revel Photo Migration Problem!

    What happened to my Photoshop/element photos? They were supposedly migrated, but I don't see them! I have no albums in my Revel account.I had a paid subscriiption and it was cancelled back in or around February, and told that the photos would be moved over to REVEL...Can anyone help me to get them back?

    First, thanks Pattie for following up with me. I am going to check my backed up hard drives to see if my photoshop materials are on them. It will take me a few days, as I have only small amounts of time to research it at this time. maybe a break will come in a day or two for a determination.
    Date: Mon, 12 Aug 2013 09:45:52 -0700
    From: [email protected]
    To: [email protected]
    Subject: Photoshop/Elements to Revel Photo Migration Problem!
        Re: Photoshop/Elements to Revel Photo Migration Problem!
        created by Pattie F in Photoshop.com Sharing and Storage - View the full discussion
    Michael-
    Is it possible you logged into Photoshop.com with a different email, or is it possible that you did not set up your Elements to sync with Photosho.com? These are the two main reasons users can not find their files.
    The Photoshop.com account created in 2009 with the email you use to log in to this forum has no files in it, and therefore, nothing migrated to the Revel account with the same login. You do have a Revel account with the same login, but it is also empty since nothing migrated.
    Pattie
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5587690#5587690
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5587690#5587690
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5587690#5587690. In the Actions box on the right, click the Stop Email Notifications link.
         Start a new discussion in Photoshop.com Sharing and Storage by email or at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

  • C7280 & Photo Tray Problem

    I have a C7280 that displays Photo Tray Problem.
    I am unable to clear this problem.
    I have tried pulling the tray out and reinserting it.
    I have tried powering the printer down by unplugging it.
    There is no telling what combination of buttons I have pushed.
    All of the above without any improvement.
    What do you suggest?
    Thanks for any and all help.

    Hi hamoonhamooni28,
    I understand you're having an issue with the photo tray on your Photosmart C7280 printer. I'm sorry to hear you've been having issues, but I will do my best to help!
    What kind of issue are you having?
    Do you get an error on the computer? Or on the printer?
    Where are you trying to print photos from? The computer or the printer?
    Once I have this information we should be able to move forward!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

  • HP C7280 Error Message "Photo Tray Problem"

    I have been through all the steps recommended for solving this but have no resolution.  HELP!

    | Photo tray problem
    +----------------------------------------------------
    | Lift the output tray up and verify that the photo tray
    |  is pushed in until it stops, then lower output all the
    | way down. Press OK button on the printer to
    | continue printing
    `--------------------------------------------------------------------------
    HP Photosmart C7280 All-in-One Printer
    1. Turn off printer.
    2. Pull out paper tray and photo tray
    3. Remove output duplexer (on back of printer)
    4. Open input sheet feeder (on top of printer)
    5. Open cartridge access door. (Basically lift up control panel and scanner section of the printer)
    6. Turn on printer (Power button on now raised control panel)
    7. Printer may display message "Performing printer alignment - Do not interrupt"
    8. Wait for a few minutes until printer stops making all setup noises.
    9. Close cartridge access door, close input sheet feeder, replace output duplexer, insert paper trays
    10. Do a test print.  All should be fine.

  • Registration problems

    I recently downloaded the free trial with which I am very impressed. I have started cataloguing past photos and have ordered the full version (shh from Amazon - sorry!). Whilst waiting for it to arrive I want to keep working on my pictures - I assume the tags etc will be imported into the full edition when it is installed.
    My problem is that everytime I complete the registration process form it 'fails to connect' despite me ticking all the boxes to be on mailing lists etc (which I don't normally like to do.) I'm in Europe (UK) and am running out of the number of times I can use the trial product - can you help?
    Thanks

    Thank you - yes but not just Firewall but all security things had to be disabled then it worked - will now scan for any nasties that came in at the same time!
    Very impressed with the speedy response - thanks.
    Gill

  • Photo gallery problems in Vista IE

    Hi there,
    I've made Spry Photo Gallery which works fine on Mac(Safari, Opera, Firefox) on Windows 2000 pro IE but don't work on Vista IE.
    I can not find a problem. Can anyone help!

    It is an HP dv6040ca that has vista 64-bit on it. It has a NVIDIA sata driver, that I have tried to up date today.
    Drat. HP has been offering a Microsoft Standard Dual Channel PCI IDE Controller Update/Rollback that has been helping with this sort of thing on desktop models (32-bit), but they aren't offering it on notebooks.
    Are you up to date on that BIOS update they are offering? (They don't say what it does, but it might be worth a crack.)
    Software & Driver downloads: HP Pavilion dv6040ca Notebook PC (Vista 64-bit)

  • LMS application registration problem

    Hi,
    I have a problem with the application registration of Campus Manager 5.2.1 under LMS 3.2.
    Right now in the "Functional" tab of the LMS portal the "Campus Manager" view is empty.
    In "Common Services" - "Server" - "Home Page Admin" - "Application Registration" Campus Manager is missing in the list of registered applications.
    I can connect to the Campus Manager using the direct link http://<servername>:1741/campus/adminIntro.do.
    The "CM" tab on the LMS portal page works.
    I tried to register it this way:
    In the CS Homepage Admin I click on "Register" - "Register from Templates" - "Next"
    Then I get the list of templates. I select "Campus Manager" - "Next".
    I enter these values:
    Server name: fully qualified name of the server
    Server Display Name: hostname of the server
    Port: 1741
    Protocol: http
    When I click on "Next" - "Finish" the Campus Manager is not added to the list of registered application and I get no error message.
    Did I enter wrong values? Where can I find corresponding log/debug messages?

    It sounds like the CMIC database may be corrupt.  There is a process to recover this, but it's somewhat complicated.  If you open a TAC service request, your engineer can walk you through the process.  This will clear out the CMIC database and reregister all applications.  That should sort you out.

Maybe you are looking for