Photoshop Lag on Windows 8 after few days after installation
Hi all guys. I need your help if anybody can help me. When I install Photoshop everything is working perfectly but after few days Photoshop starts lagging. If I unninstall it and install it again there is not any lag and It's working good but after few days the lag is back. I'm confused really because on Windows 7 there is not that lag (Just on Windows 8). I'm using Photoshop in my job pretty much and this problem confuse me.
Everything is slowing down. If I make selection it takes effect after 3-4 seconds, if I'm using brush it takes effects after 3-4 seconds too. Whole Photoshop is lagging.
Similar Messages
-
NB305-105 - Battery empty after few days
Hi,
I have a Toshiba NB305-105 (2 Gb Ram - 250 GB HDD) with Windows 7 (64) Ultimate. My battery (6 cells) has a long life about 6 hours but I don't manage why when switch-on the day after the PC the battery is discharged. I verify that PC is right switch-off and not in hibernate/stand-by but after some days the battery is complete empty.
Someone has had the same problems?
Thank for any help.
RegardsHey,
After few days the battery shouldnt be empty but it will lose a little bit power, thats normal behavior on all notebooks. Normally up to 5-10% is normal each night/day.
In your case I would check the BIOS. There you should find options like Wake up on LAN, Wake up on Keyboard and USB Sleep & Charge. Disable all these options because they are consuming power while notebook is turned off.
I did the same after this it lose just 2-4% so its very good! :) -
hi i have an iphone 4s i did an update to ios 7 , after few days i got message to update it againe to 7.0.2 but i got a message to connect my iphone to the itune.and in my computer i got a message the iphone could not be restored error occurred 29
l3az wrote:
... got a message the iphone could not be restored error occurred 29
Error 20, 21, 23, 26, 28, 29, 34, 36, 37, 40
These errors typically occur when security software interferes with the restore and update process. Use the steps to troubleshoot security software issues to resolve this issue. In rare cases, these errors may be a hardware issue. If the errors persist on another computer, the device may need service.
Also, check your hosts file to verify that it's not blocking iTunes from communicating with the update server. See the steps under the heading "Blocked by configuration (Mac OS X / Windows) > Rebuild network information > Mac OS X > The hosts file may also be blocking the iTunes Store." If you have software used to perform unauthorized modifications to the iOS device, uninstall this software prior to editing the hosts file to prevent that software from automatically modifying the hosts file again on restart -
Dear All,
I have purchased IPhone 5S in Florida Mall when I was traveling to US from India.I bought this phone in unlocked condition. I started my phone when I came back in India. After few days (4-5 days) it started giving blue dump regularly. Then I have contacted Authorized service centre (Maple) in India (Maharashtra – New Mumbai) and then Maple checked with Apple and Apple said this phone is not under International Warranty. But when I purchased this phone form Apple Florida Mall ,I have been told by Zach McKenzie (Sales Person) that it has an international warranty and u can approach to any authorized centre in India for any issues. And that’s the reason I have bought this phone.
But now I am in big trouble so tell me how can u help me in this regards.Note this is a user forum hosted by Apple. You aren't talking to Apple here just other users.
Note that the iPhone warranty is NOT international and never has been. Your iPhone must be serviced in the country of purchase.
https://www.apple.com/legal/warranty/ -
i was using 3G in my iPad 3, after few days the 3G icon disappeared and instead E icon appeared and my net is very slow with this E icon
Did you Check in settings - cellular data that 3G is enabled? Menus could be named slightly different since I use iOS 6.
-
High memory utilization after few days - ciscoworks LMS 4.0.1
Hello,
I have the problem that our ciscoworks server gets out of memory after few days. The memory utilization is always getting higher an higher (above 95%). Sometimes it is only after 3 days and sometimes it is after 1 week. So it happens not regulary. Has anyone an idea what could be the problem? I have made an screenshot from the services which use a lot of memory. And at this time the memory utilization is getting higher and higher again....I think there is a problem with tomcat or dbsrv10.exe, there are also a lot of cwjava.exe running.
Kindly regards
David MayerHello,
I have the same problem. First time I've tried to upgrade memory from 8gb to 16gb but I am still experiencing same issues (Memory is running on 98%). I'm not sure exactly what process it is causing this issue, because when I've checked all proccesses from all users running on this server and count them there is no 15 gb at all. My guess is the same for tomcat server which is responsible for RME collector, or correct me if I'm wrong.
Do you have any idea what can cause this problem.
I've tried to upgrade then to Cisco works Prime lan management 4.1, but server went with same issues.
Thanks a lot -
i have 2 iphone 3gs so i plugged 1 of them into my laptop and i downloaded i tunes everything was ok i downloaded songs so after few days i got the other i phone and i did the same thing but every thing (pictures,contacts)of the1 phone was restored to the second i phone and all the pictures of the 2 phone had gone and it only had pictures and contacts of the 1 phone anybody plz help i am in egypt and there is noo apple stores in egypt so plz help
plzzzzz help quick
-
DreamWeaver 5 quit working a few days after I downloaded.
DreamWeaver CS5 (Trial) quit working a few days after I downloaded it. I have tried reinstalling but now it won't work. The program starts but then hangs up during launching.
Try
http://forums.adobe.com/thread/629224
http://forums.adobe.com/thread/417116 -
Hi, I recently updated my IOS to 7.1.1. After few days the camera apps is missing. I'm not able to find camera anywhere in my mobile. Please help me to get it back. thanks
Hello there, Kumarlmk.
The following Featured Discussion deals with the issue you seem to be describing and provides some workable solutions:
The Camera app is suddenly missing from...: Apple Support Communities
https://discussions.apple.com/thread/5284736
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
C3750 Unable to ssh after few days!
Hi all,
If anyone could help me please, I'm having a problem with my switch, it seems that I'm losing the ablity to ssh to the switch after few days but if I reload it I can ssh into it again with no problem! At first I thought it was something wrong with my configuration so I've reconfugred the ssh, username, domain name and cleaned the rsa keys and regenrated new new ones.
My switch version is:
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9NPE-M), Version 15.0(1)SE3, RELEASE SOFTWARE (fc1)Thank you guys for the reply,
This is what I get when I try to ssh:
ssh [email protected]
[email protected]'s password:
Permission denied, please try again.
And Leo Laohoo, you guessed it right! it's look like a memory leaks, this is the output for "sh log":
*Mar 5 17:19:57.579: %AAA-3-ACCT_LOW_MEM_UID_FAIL: AAA unable to create UID for incoming calls due to insufficient processor memory
*Mar 5 17:19:58.385: %AAA-3-ACCT_LOW_MEM_UID_FAIL: AAA unable to create UID for incoming calls due to insufficient processor memory
*Mar 5 17:19:59.005: %AAA-3-ACCT_LOW_MEM_UID_FAIL: AAA unable to create UID for incoming calls due to insufficient processor memory
*Mar 6 23:22:38.979: %PARSER-5-CFGLOG_LOGGEDCMD: User:console logged command:!exec: enable
cs08#
Do you guys think of any work around other than down/upgrade the software? cuase the biggest issue now is, it's one of 9 switches that all run the same ISO version and all of them are on new production data center, and honestly I've had other weird issue with other switches too! -
HELP MY MAC BOOK PRO has a problem.
FROM A FEW DAYS AFTER A FEW HOURS .. PART ONE FAN AS HE HAD SUPERHEATED PC! is NORMAL?? do??Firstly, you aren't in MacBook Pro forum.
MacBook Pro
http://www.apple.com/support/macbookpro/
CAPS isn't really of any help reading or getting help.
Try monitoring the temperature so you know for sure. Yes it can run hot.
http://www.bresink.de/osx/TemperatureMonitor.html
You may want to boot from your original OS X DVD - hold D on statup - and that way run Apple Hardware Test -
My Mac Book Pro 13 inch shuts down when I insert some usb on port. It will be dead for few days (no power, can't charge as well, no restarting) and after few days it will work? Any one facing same issue and any solutions please...
Hi ohmghimire,
Thanks for visiting Apple Support Communities.
If you're seeing unexpected behavior when using USB devices, try resetting the SMC on your MacBook Pro:
Resetting the SMC on portables with a battery you should not remove on your own
Note: Portable computers that have a battery you should not remove on your own include MacBook Pro (Early 2009) and later, all models of MacBook Air, and MacBook (Late 2009).
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
You can find the article with these steps here:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/HT3964
If you still see this behavior after resetting the SMC, or your computer won't turn on, try the steps in this article next:
Troubleshooting: My computer won't turn on
http://support.apple.com/kb/ts1367
Best Regards,
Jeremy -
In my iPhone 4s, since I updated to the latest iOS 6.1.2 I have noticed that my battery drains very quickly, and that after 15 days after date, I lost the cell signal, I have 3g, but I can not call or receive calls or sms. HELP!
Sorry for my bad english :S
Please, please help meContact the carrier.
-
After HP replaced the motherboard, and few days later I got a black desktop and windows not genuine afterwards. Any suggestion what I should do. I tried to use Microsoft support website on the server, and it will not let me proceed to any of their site.
The browser display security certification invalid. Any help would be appreciated.
Kind RegardsHave you tried re-activating your copy of Windows? Eg, either using the prompt that appears or going into My Computer properties and checking the activation status at the bottom of the page?
From memory, when you activate a copy of Windows it makes a note of the currently installed hardware (spec, serial numbers etc) so you can't just copy all the files onto another machine and use it there. My guess is that the setup has changed enough for
it to no longer recognise it as the same machine (though I thought it normally takes a few elements changing to trigger that reaction), and so thinks it's no longer genuine. Getting Windows to activate again may work, otherwise you'll probably need to phone
Microsoft to get them to sort it out and allow it to activate again. -
Mac set-up window appears 3 days after upgrade-everything was fine 'til now
I posted a question recently in the iMac (CRT) forum and linked to it here (regarding disappearing finder/desktop on my father-in-law's computer after an OS 10.3 upgrade via DVDs purchased from Other World Computing). I solved the problem (or so I thought) by purchasing a different set of Panther CDs (from applerescue.com) and installing them.
Unfortunately, he can't get into his old desktop and files again. But the problem is different than the one that presented itself on that previous upgrade. At least after that one, he had access to his old files, etc.
The installation (Archive and Install) was done on Thursday. Several reboots were successful that day. I left the upgrade (from 10.3) to 10.3.9 for another time. My father-in-law started up successfully that night, Friday, and Saturday (though he ran into a problem with a printer that was not recognized - easily repaired, had that been the only problem). This morning, Sunday, he started up and was unhappily presented with the OS X welcome screen. I ran over to his house this afternoon and was unable to bypass the screen by any method I knew of (as I said, his computer behaved normally prior to today --- booted right up into his account as before the upgrade for the past three days). I started to enter information into the unavoidable fields, but aborted when I realized that I might not have access to his old accounts (and files, which we had backed up, of course).
What could possibly be causing the welcome window to show up? I've only seen it in two circumstances: 1) Starting up a new computer; 2) When doing an erase and install.
While waiting to see whether anyone has a clue as to what has happened, I will connect my computer to his and see whether all his old files are intact.
In case it helps, here is the older item regarding this computer posted in the iMac G3 forum:
http://discussions.apple.com/thread.jspa?threadID=759902&tstart=0
Thanks for your insight (as opposed to iSight).
Leonard
G5 iMac (iSight) Mac OS X (10.4.7) 1.5 Gb RAMThe old iMac is now working fine, so I've marked the question as answered, even though I still don't know why the problem occurred or how, exactly, it got fixed.
Here's the latest, for anyone interested in the outcome:
When we last looked in on our father-in-law's hapless computer, it was displaying the welcome screen/set-up window after the Archive and Install of 10.3 from a new set of (supposedly) universal install disks. It was behaving like a new computer that had never been used before (or like a computer whose OS was installed after a complete wiping of the disk). An examination via our own G5 iMac (with the CRT iMac in Target Disk Mode) showed that all the files and accounts were intact, yet the computer was still insisting that we set up an account so we could use it.
Concerned that we might lose (easy) access to the old main account - even though we had backed up everything, I elected to reinstall the OS hoping to avoid erasing the disk. When I had done this a few days ago (using the new disks to install 10.3 over the 10.3.9 version that was working but not showing the desktop/finder), I did an Archive and Install, since (of course) I couldn't install an earlier version on top of a later version.
This time, I had the Upgrade option available. I have no idea why, since I was installing the same version of the software as was in the machine already. (That may be normal, however. I don't know, nor does it matter particularly.) I chose that option, rather than Archive and Install hoping the iMac would rediscover its accounts.
The installation went smoothly (though it took lots longer, since I forgot to de-select all the printer drivers and other language support). However, I was presented with the welcome screen yet again. A quick check, again via the G5 with the CRT iMac in Target Disk Mode, showed that all the files and accounts were still there.
I had nothing to lose, so I set up a new account. Once I had a desktop, I went to System Preferences/Accounts, and saw that both older accounts were still there (marked as Administrator accounts as before). I changed the login preferences, selecting the old main user account for automatic login.
I restarted, and the old desktop appeared. All the files were intact and accessible, so I updated to 10.3.9 with the matching Java update.
Hopefully that's the end of it. The previous strange behavior is still a mystery, though.
As to the disks, I understand the nature of machine specific disks and the problems they can cause, even though those eMac DVDs worked fine with my old retired PowerBook. Those disks were sold as UNIVERSAL install disks (or I wouldn't have bought them) by Other World Computing - I wonder how they can make that claim. Those disks also installed 10.3.4 on the iMac (which I then updated to 10.3.9), but the Finder did not work, and I couldn't get a desktop, as I said in an earlier message. Why they worked on the PowerBook, i don't know.
This latest set of Panther disks (3 CDs) were sold by applerescue.com as universal install disks also. They are version 10.3 only (not 10.3.x) and are not marked for any particular machine. However, they are white, not black like the illustration that Don and others have linked to as being the retail version of the OS. Are they the problem? Who knows? And where did they come from if they aren't the retail version or a machine specific version?
Sooner or later, I'd like to figure all of this out, but for now we have a working computer.
(Thanks again to Don Morgan.)
Leonard
G5 iMac (iSight) Mac OS X (10.4.7) 1.5 Gb RAM
Maybe you are looking for
-
The iTunes library on our laptop is correct and up to date with recent purchases and downloads; however, our desktop does not have any of these when using it. Home sharing is turned "ON" with both computers. Why is the desktop not showing the same c
-
Can no longer pull clip into timeline from Viewer??
I no longer have the ability to drag a clip, or sub clip if I've chosen in and out points, into the timeline from the Viewer. When I attempt to do this the clip moves as if I'm repositioning the clip within the Viewer window, but does not move to the
-
THE BEST OF MAY Have you seen this page? It´s incredible!!! I think that I know what it is, but I am not sure. This is the page: http://www.lanzadera.com/curio200 Please if you know what it is, send me and e-mail. Mitch
-
Remove Blank Page conditionally in Smartforms
Hi Experts this is Arun, I have Requirement in such a way that, Form should contain three different pages which display three different records using three different internal tables.My problem is I have to avoid second and third page if it does not
-
Unicode word boundaries in Regex
Dear All, I am using the following simple regex: "\\w+" which matches one more word characters. My problem is that it is not matching unicode characters which are part of my language. Is there any way to force java regex engine to include unicode cha