Photosmart 7510 wireless problem.. Fed Up

I have a Photosmart 7510 and it keeps loosing connection with my router. I am fed up turning it off and on,so I am going to wire it directly into my Mac via USB CABLE. Is there any setting that I have to change on my Mac ? Or can I start printing right away ?  

Do you want to work on the wireless issue at all?
To answer your question, first download and install this: http://support.apple.com/kb/DL907
Restart your Mac.
Now, plug the printer directly into your Mac.  Within a minute or so you will be able to print/scan.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

  • MAC can't find HP Photosmart 7510 wirelessly

    I cannot make my HP Photosmart 7510 link to my Mac which runs on 10.8.3. I have downloaded the software from the link below:
    http://ftp.hp.com/pub/softlib/software12/COL44228/mp-107205-1/HP_Mountain_Lion_Ink_SW_v12.23.38.dmg
    I have connected the 2 by cable, set everything up, it all says it works - when I remove the cable it gives me the message below - can you help?
    The wireless network settings were successfully downloaded to your device. However, your Mac was unable to locate the device on the network.
    Please make sure that:
    • Your Mac is connected to a wired or wireless network that has access to your device.
    • Your device is connected to the wireless network "XXX".
    Click "Retry" to attempt to connect again using the current settings. Click "Go Back" to enter different settings.

    That is close.  To verify that the "Service Order" is correct, click the gear icon at the bottom of that window and select Set Service Order.  Drag the connetion types around to get the proper order.  Your Mac prioritizes network connections in the order you set in this window.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Photosmart 7510 cartridge problem error

    I keep getting a "Cartridge Problem" error.  It says "until cartridges are installed, make sure the printer is turned on to avoid damage to the printer. 
    I have new cartridges in and everything looks okay but I cant get past this message.
    Help please!

    Hi SLC123,
    I understand you have a Photosmart 7510 that is giving you a cartridge problem error even though all of the cartridges are inserted. I'm sorry to hear this, but I will definitely do my best to help you!
    I will recommend that you start with following this 'Ink Cartridge Problem,' 'Incompatible Ink Cartridge,' or 'Ink Cartridge Failure' Message Displays o... document and these steps should be able to help.
    Hope this helps, have a great day!!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

  • Photosmart 7280 wireless problem

    My photosmart all in one 7280 printer stops printing and leaves jobs in the print que.  I am using a wireless home network to connect to my Dell laptop using Windows Vista. Anyone else having problems or have you fixed a similar problem?

    hello,
    make sure you have the exact ip address.
    press the setup button of the printer and use the arrow button and go to network and press ok.
    look for view network settings and press ok.
    look for print network configuration page and press ok.
    check the ip address and take note of it.
    in your computer, click on start and click on control panel,
    click on printers
    right click on your printer driver and click properties
    click on ports and check the port that has a check mark
    if port is not using the exact ip address, click on configure port, change the ip address with the ip address on the configuration page.
    click apply and click ok
    try to print again
    keep me informed please..

  • HP Photosmart B110a wireless problems !!

    OK I've trawled every forum and wasted an awful lot of time courtesy of HP !! Have a MacBook Pro, iPhone4 & 3GS + iPad2 ; all connected via a Netgear 834bg, all software/firmware up to date. It has to be said I'm fairly Tech Savvy and can solve/hack most problems, that is apart from WiFi connection to a HP printer. Had a C4580 before the B110a, this worked brilliantly over Wifi (scan/print) up until 18 months ago after an update (Apple/HP). As mentioned it stopped working, thought WiFi radio was bust but eventually came to the conclusion that it was working OK - nevertheless went foe an upgrade (or so I thought) for iPad/iPhone/AirPrint connectivity. Well I have now eventually managed to 'connect' MacBook / IP4/iPad etc. no thanks to HP and its useless manuals and install procedure (went through this at least 5 times - from scratch !!). As said I'm fairly capable in solving tech problems, this has been an appalling struggle !!! Judging from this support website and other forums it is a slim comfort to see how many people have real difficulties with what should be a straight forward install procedure. HP is as a company very good at producing greatly hyped websites and advertising about their products - what if YOU (HP) put as much effort in getting your products to work straight out of the box ?? Any Apple product I have bought have ALWAYS worked - just like that, don't get me wrong I've been a great fan of HP as a company until this purchase. There are a lot of customers fumbling in the dark with WiFi and connectivity issues; very obviously so in this forum !!
    As for the comment  'Want Good Answers - Ask Good Questions' ; how about
    'Want Happy customers ? Write good Software !!
    I will share my solutions at a later stage, hopefully it will offer some solutions - I do not want 'HP users' to go through the same HP-Hell as I have 

    OK just to clarify how I managed to get what somehow looks like a reasonable/stable connection, this follows trawling this and other forums for clues - Thanks to those who have provided me with some of these clues, can't remember names
    You need to get in to the EWS (embedded web server) of the printer, paste URL from network configuration page into Safari etc. (192.168.0.xx). See screenshots: Assign Manual IP4 adress+ subnet+default gateway. You also need to get to the Advanced section in Network Tab, make sure you've got WPA (PSK) with 13chars+ password, WEP will not work ! I stress that this procedure is tested for MACBook/iPad2/iPhone4 only, but should work for Windows as well. So BIG question to HP : WHY oh WHY is all this necessary ????

  • Photosmart c4599 wireless problem

    Hi,
    I'm trying to set up my C4599, but whenever I go through the setup process I get the following error after the diagnostic test:
    "The connected printer does not support wireless networking"
    How can I solve this?
    Thanks

    I got the same message installing a C4580 on Windows XP connected with a cable to a Linksys 54G wireless router "The connected printer does not support wireless networking".  It also stumped the support tech.  In my case, no amount of fooling with the firewall, channel, rebooting, etc. made one whit of difference.  I tried to install on my Vista laptop.  Same error (but I could continue if I connected to HPsetup under wireless networks - not a working solution, though).  However the support tech noted that I had other HP services installed on the XP.  That gave me an idea.  I did have an HP D4200 installed.  I used add or remove programs on the control panel to remove all HP products.  I rebooted everything.  Then the C4580 installed.  I gather the C4580 installation software is simply incompatible with the D4200 software since I tried the installation on two very different computers with only the wireless router and the D4200 in common and ended up with the identical error message.
    After installing, I still got an error about a firewall possibly blocking a port.  It asked if I wanted to continue via USB.  I did so.  I shut down both the printer and the computer.  The printer hung on shutdown, and I had to unplug it.  I also removed the USB cable.  When I turned things back on, they worked.  My Vista laptop already had the drivers and fired up without further ado.  However, if the printer is turned off, the laptop connection goes offline and does not immediately come back online when the printer is turned on.  One can click the printer icon and make it online, but it is a little irritating.
    Message Edited by gernt on 04-16-2009 06:30 AM
    Message Edited by gernt on 04-16-2009 06:35 AM

  • HP Photosmart 7510 printer wireless connection to Mac Book Pro

    My new HP Photosmart 7510 wireless printer won't stay "connected" to my Mac Book Pro.  Every time I try to print, it says it is "looking for printer" and "printer is disconnected."  Sometimes it finds the printer and I get the pages, but several times, it hasn't found the printer at all.  Thanks!

    Hi there clhs,
    Could you provide the community with a little more information to help narrow troubleshooting? How are we connected to the printer USB/Wireless/ethernet?
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Issue setting up eFax on HP Photosmart 7510 e-All-in-One "Problem connecting to internet"

    I'm having an issue setting up eFax on my new HP Photosmart 7510 e-All-in-One. I am following the on-screen instructions and receive an error "Problem connecting to internet" when trying to register the account. The ePrint service is working, and I can use the facebook app on the printer so it seems to be connecting to the internet. I am uncertain how to resolve the issue.

    Let's set a static IP address and external DNS for the printer:
    - Print a Network Config Page from the front of the printer. Note the printer's IP address.
    - Type that IP address into a browser to reveal the printer's internal settings.
    - Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
    - On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
    - Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
    - Enter your router's IP (on the Network Config Page) for the gateway.
    - Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS.
    - Click 'Apply'.
    Now, shut down the router and printer, start the router, wait, then start the printer.
    After this you may need to redo 'Add a Printer' using the new IP address.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Problem with HP Photosmart 7510

     Everytime I go to print something on my HP Photosmart 7510 printer I have to shut down the printer and restart it to print anything. It's almost like it goes into sleep mode but doesn't  "wake up"

    Hi @jrs67413
    This document contains information about the possible causes of a lost wireless connection, tips for avoiding the issue, tips for maintaining a connection, and troubleshooting steps to help you restore the wireless connection on your printer; Printer Does Not Maintain Wireless Connection.
    In addition to the solutions offered in the document and what you have probably already tried, please ensure the printer is connected directly to a wall outlet and not into a surge protector/ power bar. Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector
    In this document you will see,
    ISSUE:
    Problems or issues may arise when an HP LaserJet series printer is connected to an uninterruptible power supply (UPS), a power strip, or a surge protector
    This is not limited to Laserjet printers.
    It is also good, if you haven't already, to be sure the printer firmware is up to date.  Getting Printer Updates for HP Photosmart 7510 e-All-in-One Printer Series
    I hope this is helpful. 
    I just thought of something else you could try. Use the steps below to disable UPnP in the printers EWS,
    1. Typing the printers assigned IP address into the address bar of Internet Explorer. (you can get this from the report you would have printed while following the steps in the document I posted above)
    2. Click on the Network Tab at the top
    3. Select the Networking option on the left
    4. Click on UPnP option on the left
    5. Select the 'Disable UPnP' radio button
    6. Click 'Apply'
    Also, I would like to disable to IPv6 on the printer. This setting can sometimes cause issues. Use the instructions below to disable the IPv6
    On the front panel of the printer, touch the Wireless icon, it's the second of the four icons on the top.
    Navigate through the Wireless menu to  Advanced Settings and go to IPv6
    Turn IPv6 off
    I will watch for a reply from you. Thanks.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • HP Photosmart 7510 occasional​ly loses its wireless settings

    I have a HP Photosmart 7510 which occasionally loses its WPA-PSK secret and manually set IP address.
    To solve the problem I have to re-enter the SSID's WPA-PSK secret and set the manual IP address (I prefer having the printer on a specific IP address).
    To my knowledge the printer has not been powered down and there were no power failure - though I would expect these values to have been stored in non-volatile memory.
    Is this a known issue?
    If so is there a firmware fix - currently running VEP1CN1137CR(113730)

    I can assure you that it is not a router issue.  It appears to me that it is a driver compatibility with Windows OS.  After trying to get to the bottom of this since my Photosmart 7525 was new and reading just about every forum and blog, I have come to the conclusion that the issue must be related to the HP driver itself.  
    The issue does not seem to affect any Mac systems, and from one forum someone was able to fix it by downloading new drivers compatible with 64-bit systems (which seem to not be affected by the glitch).  But that leaves us 32-bit people stuck with the current driver which does not work.
    The printer is connected with good signal to the wireless router (no matter who's router it is and what configuration is made).  The printer can be pinged from the router and any computer on the network which is not currently being affected by this issue.  However, the affected computer fails pings by either request timed out, or destination host unreachable.  Pings are successful from the affected computer to any other device on the network.  The only way to recover (at least for a few days) is to reboot the affected computer.
    Also, from the display on the 7525, the network tests pass without issue.  I can also download and print content from the internet with no issues.  
    Please do a quick google search of this issue and you will see several THOUSAND entries of people with the same request.  This is a serious issue that people are having and everything is pointing to an HP problem (not routers, improper installation of software or drivers, etc...).  I agree with several other customers that HP should be on the hook for this fix.  I will give it another couple weeks, then back to the store for a reliable unit from another competitor (Canon, Lexmark, etc..)
    Thank you in advance for escalating this issue to product engineering,
    S. Hunn
    There are 10 kinds of people in this world... Those who understand binary and those who do not.

  • HP Photosmart series 7510 wireless printer issue

    I have a  HP Photosmart series 7510 wireless printer.   
    My laptop is an HP Pavillion Entertainment PC dv9700.
    I am running Vista Home Premium with Service Pack 2.
    The printer stopped responding when I attempt to print something from the laptop, such as a web page or document.  When I print a diagnostic page it goes and responds right away. 
    Any ideas of what I may try.  When I set up a regular print job it just stays in the que and does not print.
    Thank in advance.

    Hello szwonders,
    I am sorry to hear you are having an issue with printing with your Photosmart 7510. Thank you for your information.
    I would like to help you.
    I recommend Resetting your Printer first, to see if that helps.
    Also, I recommend running HP's Print and Scan Doctor for Windows to search the driver and software to see if there are any issues.
    Please respond to let me know if this helped or if you have any other questions!
    Thanks,
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • I have a macbook pro. i have a photosmart 7510. we just bought a new windows tower and the printer works wireless for us, but now the mac does not print anymore wirelessly. i keep getting a message Network host 'HPE93F2A.local.' is busy. what can i do to

    I have a macbook pro. i have a photosmart 7510. we just bought a new windows tower and the printer works wireless for us, but now the mac does not print anymore wirelessly. i keep getting a message Network host 'HPE93F2A.local.' is busy. what can i do to

    it is a windows 8

  • Photosmart 7510 e-all-in-o​ne series/ Printhead problem.

    Our photosmart 7510 e-all-in-one series has an message that reads 
    Printhead appears to be missing, not detected, or incorrectly installed.
    Not able to locate the problem.
    Happened right after I changed the ink. 

    Hello harry4955,
    Welcome to the HP Support Forums!
    I see that the HP Photosmart 7510 is displaying an error regarding the print head is missing, stating after changing your ink cartridges.
    I was able to locate this HP document: 'Missing or Failed Printhead' or 'Printhead is Missing, Not Detected, or Not Properly Installed' Mes.... I hope it helps, if not you may need to call HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here.
    Regards,
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • Has anyone had a problem centering labels from microsoft word 2007 using the hp photosmart 7510? my

    Has anyone had a problem with printing labels centered on HP Photosmart 7510 e-All in one?  My labels are printed from Word 2007 and appear on the screen to be centered, however when I print, they are too high on the label.  Also when printing an e-mail the bottom of the page where it lists your email name is cut off.  Please help!!

    Hi,
    I'd been having this problem for probably round 30 years on many printers. I bought a labels printer few years back but I don't print labels everyday now.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • My iPad shows my Photosmart 7510 but won't print. Wireless commands from my computer to printer work

    My iPad shows my Photosmart 7510 but won't print. I've disconnected and reconnected printer, turned iPad off and on.  My computer communicates well wirelessly with the printer. Troubleshoot further?

    I would try a hard reset on the iPad.
    To do so, hold both the home button and sleep button down at the same time.
    Keep holding them until the device restarts and you see the Apple logo.
    Once you see the Apple logo, you can go ahead and release the buttons.
    Once the iPad is booted back up, try to print to your 7510 again.
    Let know if that helps resolve your issue or not.
    Best of luck,
    Kyle

Maybe you are looking for