PI 7.0, SP 12, Communication Channel not available

Hi everyone,
I have installed SP12. In Component monitoring, communication channle button is not there. Can anyone tell me why? What i have to do with this?
Rgs
Bala

Hi Bala,
1.Have you done the post installations procedures ??
2. You have import the latest SAP BASIS Component to your design time environment.
Regards
Ramesh P

Similar Messages

  • Requested circuit/channel not available

    Hello,
    I have a problem with a PRI link. We have installed CCM 3.3(3) and a 3745 with a PRI link to the telco. The 3745 is configured as a MGCP gateway. When I try to initiate an outbound call, I get the following Q931 debug message:
    *Mar 1 01:47:14.967: ISDN Se3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0005
    Bearer Capability i = 0x8090A3
    Standard = CCITT
    Transer Capability = Speech
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA9839F
    Exclusive, Channel 31
    Calling Party Number i = 0x0081, 'XXXXXXX'
    Plan:Unknown, Type:Unknown
    Called Party Number i = 0x80, 'XXXXXXXXXX'
    Plan:Unknown, Type:Unknown
    *Mar 1 01:47:15.127: ISDN Se3/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x8005
    Cause i = 0x82AC - Requested circuit/channel not available
    When I try an inbound call I get a busy signal, and a similar debug message (if I use another router to initiate that ISDN call).
    This is the "show ISDN state" screen:
    ISDN Serial3/0:15 interface
    dsl 0, interface ISDN Switchtype = primary-net5
    L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
    Layer 1 Status:
    ACTIVE
    Layer 2 Status:
    TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0xFFFF7FFF
    Number of L2 Discards = 1, L2 Session ID = 13
    So I presume there is nothing wrong with the signalization??
    I contacted the telco person, and he told be that he sees some kind of BLOCKING state on our side of the PRI link.
    Please help or give at least some guidelines what to try next!
    Thanks in advance...

    Haha, 11 years later this post save us on CUCM 8.6.2, disabled "Inhibit restarts at PRI initialization" Works Excellent on the E1 affected.
    THANKS A LOOOT.

  • TV Says Channel Not Available

    So My TV says channel not available and I called Verzion and they are not able to help me.  I pay almost $200 dollars a month for service and I get the run around.  I am about to cancel my service if someone doesnt call me back or send a tech out to find out why is it that I am calling twice in one month for the same issue.

    One of course is to make sure its a channel you are suppose to get.
    Complaining here is just complaining to your Peers.  YOu need to follow through with contacting Verizon support.  http://www22.verizon.com/content/contactus/

  • One TV keeps getting message this channel not available

    OK so one TV an older one, in my home keeps getting the message this channel not available.  I went through ll the trouble shooting steps.  My other two TVs are fine but they are new one's.  This is my grandpas' old one.

    I'm sure it happens to many channels from time to time, because that is what happens to me.  On the DVR or on the HD STB.  Tonight I sat down to watch the Yankees play the Phillies on ESPN.  My 2 favorite teams, very excited.  At first ESPN doesn't load, then I get the BSOD w/ the white letters in the middle of the screen telling me the channel is unavailable.  It provides me w/ 2 options.  Option 1 is to switch away from this channel and back again (didn't work).  Option 2 is to call the toll free number, input a code and everything will be fine. 
    So I called the toll free number, entered the codes as prompted, and listened to the robot lady while she reset my DVR.  She told me to look for the yellow light to the left of the display after the reset and if the yellow light wasn't there, to turn on the DVR using the power button on the DVR.  I did not see the yellow light, so I turned the power on as instructed by the robot lady.  However, still no yellow light.  The robot lady is only prompting me to say next, repeat the instructions for the #%&^*(*&%@!!!#%$^ yellow light, or say problem fixed.  When I took her up on her offer of more info, she simply repeated the thing about the yellow light.
    How about adding a prompt to her repertoire asking if the yellow light isn't there.... I guarantee this will be the most used prompt.
    Meanwhile, I am too experienced and sane to call for tech support, live chat is always unavailable, so I am left waiting for some verizon kool-aid-drinking "guru" to tell me my coax is bad in the forums.
    Good night.

  • Channel not available. and bad gateway

    TO add to our new fios installation woes we are now getting channel not available error on one of our boxes as well as the bad gateway error. 
    I discontected all the coax and reconeted and tried all the trouble shooting steps.. any advice?
    Thanks
    I should add this is only happening on a few channels that i can find. syfi hd is one.  ALso im not seeing this issue on our main box. 
    UPDATE: channel not available fixed by tech who installed the proper spiltters.

    Glad to hear the channel issue is fixed. We would like to help with the gateway problem. I need to get come circuit information from you. I have sent you a private message to get more information.
    Anthony_VZ
    **If someones post has helped you, please acknowledge their assistance by clicking the red thumbs up button to give them Kudos. If you are the original poster and any response gave you your answer, please mark the post that had the answer as the solution**
    Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or plan

  • PI 7.1 RFC Communication Channel not found

    Hello,
    We have recently upgraded to PI 7.1 and I am having a problem getting my RFC adapter to work.  This is the error message:
    Error when calling an adapter by using the communication channel CC_UDF_RFC_CALL_TO_PI_ABAP (Party: , Service: IS_D06, Object ID: 5873a160602e3be5866ab820596b752c) The channel with object ID 5873a160602e3be5866ab820596b752c could not be found in the Integration Server Java Cache. Check if the channel exists in the Integration Builder Directory and execute a refresh of the Java Cache
    I went to SXI_CACHE and refreshed (Delta nad Complete).  I can see that the CC exists in integration builder.  
    How can I determine what is causing this error?
    Thanks,
    Matt

    Also check the cache notification after activating the Comm channel in ID whether cache is properly updating for the changes in the comm channel.
    Menu--> Environment --> Cache Notification
    If cache notification is proper thentry to refresh CPA cache using following URL and execute ur scenario.
    [http://<host>:<port>/CPACache/refresh?mode=full]
    Edited by: Samiullah Qureshi on May 14, 2009 8:36 AM

  • Error in communication channel " not initialized"

    Hi All,
           I'm working in FIle to mail scenario. In this scenario whenever i upload a text file to the R/3 application server. that file should be sent (as a attachment with a mail) to any email id. I did all the required configuration in IR. but i'm verymuch confused in ID configuration. I have created both sender and receiver communication channel in the same business system which refers a sender (R/3) System.sender communication channel is working fine. but when i activate the receiver communication channel it shows an error "not initialized".
    So kindly let me know,
    1. Should i use business system for my receiver end?,If so how do i create it?
    2. is receiver agreement, receiver determination, interface mapping necessary? If so, how do i configure it? because i'm not using any recever service since i'm sending mail to my mail box.
    note:
    It would be very helpful if u refer any link to find out the recever determination and interface determination configuration for this type of scenario.
    Thanks & Regards,
    hari.

    Provide us the XML formed after mapping.
    make sure that the msg type name is Mail and the name space name is http://sap.com/xi/XI/Mail/30.
    regards
    krishna

  • Error in JMS Communication Channel not raising alert

    Processing Errors in JMS Communication Channel are not raising alerts.
    The settings on the communication channel retires are set at 3 and 5min interval.
    In RWB the JMS communication channel shows processing errors but an alert is not raised.
    The alert are configured in our system and we even have a catch all alert rule with * (wildcard). Errors in PI message processing are raising alerts but errors in Comm Channel are not raising alerts.
    The message in SXI_MONITOR shows as processed successfully but when we check the RWB and Comm. Channel Monitoring we see processing errors "Channel error occured; detailed error description: JMS error: Connection to the server has been terminated; Linked error: Connection reset, Error Code:null"
    Are we missing any configuration? How do we get alerts/notifications if there are errors in Comm. Channel without having to login into RWB and watch it periodically?
    Any help is greatly appreciated.
    RM

    Hi,
    What is the staus of Communication channel in RWB when it fails, RED ??if yes then it should genarate alert.
    create one more alert for specific to JMS interface and check it out.
    Regards,
    Raj

  • Mail Sender Communication channel not polling

    Dear all,
    In our PI 7.1 Sever, we have observed a issue.
    Sender mail communication channel status is green in RWB-->Channel monitoring but the channel does not pick up any mails form the mailbox.
    After we stop and then start the channel, it is picking up the mails.
    Any pointers on the root casue for this issue and any resolution steps or any SAP Notes to implement will be of great help.
    Regards,
    Younus

    Hi,
    Is it like everytime you have to restart the mail channel again and again?
    Sometimes it happens, a quick restart will refresh the adapter cache and the messages are processed.
    So, its not a problem.
    Regards,
    Sushama

  • PI sender communication channel not reading files from NFS directory

    Hello,
    I have a sender communication channel configured to read file from NFS directory which is on ECC server. A program in ECC generates the file and puts it on the ECC server in the output directory. PI sender communication channel is supposed to pickup this file and process it. If I give the NFS path as the source directory, I am getting error: Configured source directory '//Server/DIR/OUT' does not exist. I tried putting '
    Server\DIR\OUT' too but same error. Do I have to add the NFS path of ECC into PI as logical path?
    Any suggestions?
    Thanks,
    Sangita

    Hello Sangita,
    Your ECC server is an external system, therefore you need to activate FTP service in that system and use the transport protocol FTP:
    http://help.sap.com/saphelp_nw04/helpdata/en/e3/94007075cae04f930cc4c034e411e1/content.htm
    You can use NFS protocol when you have a local directory in XI server.
    Best Regards,
    .Luis Bernal.

  • Communication channel not listed in RWB

    Hi,
    I'm facing a strange problem.
    Working on File to IDOC scenario. Suddenly my communication channel has stoppped listing in RWB.
    It say 0 channel found. Initially it was not so and I was able to monitor my channel.
    Any help on this ?
    Vikas

    Hi Vikas,
    -->In the ID deactivate your File sender communication channel and activate it.
    -->also refresh the cache.
    Thanks

  • Communication channel not selectable in monitoring

    Dear experts,
    From SAP 4.6c, I want to send data to XI via RFC adapter. I did the following:
    - create an RFC on sap 4.6 with no coding, only parameters;
    - import the RFC in the integration repository;
    - did the message- and interfacemapping to my outputstructure there;
    - configured everything in the integration directory, so comm.channel, send/receiv determination etc.
    - on the SAP system, created an abap that fills the parameters for the RFC and calls RFC with destination = XI system.
    I created a Sender Comm.channel (from SAP to XI) with adaptertype RFC and set it to Active.
    Now, when I look in the Communication Channel Monitoring in the Runtime Workbench, I can not select the CC. I'just does not appear when I press "input help" button. I must e forgetting something but I have no idea what...
    Can anybody please help?
    Thanks in advance
    William

    Hi JWD,
    Check in your change list whether it is activated or not. If activated you should be able to see.
    Regards,
    ---Satish

  • Communication channel not visible in RWB

    Hello everyone,
    I am not able to view the communication channel in RWB. This is a HTTP sender . i have imported it but still it is not visible in  RWB. what could be the reason ?
    Regards,
    Ravi

    Hi Ravi,
    In PI there are basically two types of adapter, adapter engine based and Integration engine based. Integration engine based adapters are HTTP, XI and IDOC. These adapters can be monitored from ABAP stack means from SXI_MONITOR and adapter engine based can be monitored from RWB. Due to this differentiation you HTTP adatper is not visitble in RWB. But you can monitor it from ABAP stack.
    Edited by: Rajhans Abhay on Jan 18, 2012 6:06 AM

  • Communication channel not present in Communication channel monitoring

    Hi All,
    We have the communication channel in Integration builder and it is active state. but we are not able to see it in C.C monitoring. and we are not sure whether the channels are started.
    how can we check whether the channels are started?
    and why the communication channel is not visible in C.C monitoring.
    It works fine in DEV and QA. but we are facing this issue in PRD

    Hi Ravi,
    in the cache connectivity test, all the components are in GREEN color (Enterprise Service Repository, Integration directory, Integration server - ABAP, , mapping runtime on central adapter engine, adapter engine, mapping runtime) . Only central adapter engine is in yellow color and the message says:
    Apr 19, 2010 6:16:28 AM - Cache notification from Integration Directory received successfully
    Attempt to fetch cache data from Integration Directory not yet started or still in process.
    Restarting the server also did not work.

  • Sender JMS Synchronous communication channel not picking up files from JMS

    Hello,
    One of our Sender JMS synchronous communication channel (used Sync/Async bridge in the module section to make it Synchronous) is not picking up files from JMS system though the channel looks to be active (greeen).
    When I am trying to stop the channel, it is giving error as "1 of 1 administered and selected channels have not been stopped", and after this when I start the cannel again it shows green but not picking up any files.
    if anyone is haivng any solution for this, please reply back.
    Thanks in advance.

    Messages available in JMS system? please check queue's if message were there and it is not picking up then some thing wrong with cc.
    simple solution create new communication channel with same details and try to use the same.

Maybe you are looking for