PI 7.30 dual stack - different time in rwb, pimon and ABAP stack
Hi @all,
I am working with the client on a PI 7.30 dual stack system.
During monitoring of message processing I saw that there are differences in the time displayed while monitoring the processing of identical messages
e.g. channelmonitor (mdt/channelmonitorservlet and rwb) is 1 hour behind pimon
The time displayed in the ABAP Stack (Menu System - Status) differs also 2 hours ahead of pimon.
Are there java parameters to configure the used time zone and which could be reason for this behaviour.
For me it seems strange that there is a difference between to tools (channelmonitor and pimon) I was supposing are based on the same technical stack
Would be nice to have the same time throughout the whole system.
Any help appreciated.
Best regards
Jochen
Hi Jochen,
I did not found the option to change the time zone for pimon. Please refer the below wiki it might helpful
PiMon_TroubleshootingGuide - Technical Operations - SCN Wiki
PiMon_Frequently Asked Questions - Technical Operations - SCN Wiki
regards.
Harish
Similar Messages
-
Hi Experts,
i am now confused about these two stacks: Java Stack and ABAP Stack.
for IR objects, like DT, MT, SI, MM, SM, Action, Process Integration Scenario
for ID objects, like profile agreements, receiver determination, interface determination,
1. where are these objects stored in? Java or ABAP stack?
and i know Adapter Engine is run on JAVA Stack while Integration Engine is on ABAP Stack.
2. how do they call the objects stored in different stack during processing?Hi,
1. where are these objects stored in? Java or ABAP stack?
These objects are basically developed on the JAVA stack, when they are activated their runtime version is created on ABAP stack, which you can check in SXI_CACHE transaction.
2. how do they call the objects stored in different stack during processing?
Runtime versions of these objects are responsible for the execution of the interfaces.
-Supriya. -
Installing Java Stack and Abap Stack, same machine.
Hi all:
Does anybody installed Java Stack and Abap Stack on the same machine?
I installed ABAP stack first, and am trying now to install Java stack but it seems like at the end of the process, ABAP stack. (is not working now).
Any idea?Not sure about installing both as I haven't tried either!
Anyway, in theory if the SIDs and instance numbers are completely different, then you should be OK. If you ahev the same SID or instance number, I can see possible problems,
Portal only runs on Java, so in theory any Java system will be OK. NWDW would be a good choice. -
SMSY for ERP JAVA and ABAP Stack
Hi Folks - I have installed SAP ERP 6.0 EHP5 in one database called T12. Now there is a need for a Java stack and I have installed the Java stack in another database called J12.
I was able to define the ABAP stack on system landscape and MOPZ is working fine. However, I am not sure how I should go about the Java (J12) instance definidstion on SMSY.
I am using Somlam 7.1 on Oracle Linux system.
ABAP stack is on ERL 6.0 EHP5 and Java stack is Netweaver 7.0 EHP2.
J12 and T12 systems are connected via JCO.
SLD has been defined for both stacks and they are using the local SLD for the SolMan.
Your help is much appriciated.Sunny - I checked the SLD and It is working fine. There were couple of issues that I fixed. Since I defined the Java system manually I delete it. Hopefully SLD will populate the definition.
In same note, Would it be possible that installing ERP java and ABAP stack on different hosts (stand alone) is causing this issue, especially they are using different Sid's?
I was reading SAP Note 1344564, It states
III.Some Main Instances include other Main Instances (E.g., in SAP
ERP 6.0, Main Instance SAP NW - Enterprise Portal includes SAP NW -
EP Core.). If the including Main Instance is installed, it's not
necessary to mark the included Main Instance(s) for relevance.
Is this mean in SMSY I do not have to define any product for the Java engine? When installing the Java, I had to create the product manually to be able to generate the installation key.
Your input is appreciated.
Edited by: kourosh Ghouchkhani on Nov 22, 2011 1:20 AM -
How to check Integration Server Client and ABAP stack Client?
How to check Integration Server Client and ABAP stack Client? How to check,,pls tell in detailed steps???
Points would be awarded.
Arnabhi,
Must be the server has different clients,one declared as application server ie abap stack client and the other declared as Integration server ie XI. U might be trying to open idx5 in application server client, in which idx5 exists but you cant open the screen even, that can be achieved through we02.
000 is the default client when XI server is installed .We can create separate clients on the system through sccl tcode.
As told we can find the client on sap logon screen.
Logon to sxmb_adm and check whether the client is declared as an application system(r/3) or Integration server(xi).Try idx5 in xi not r/3
Edited by: NagaDurga Nannapaneni on Aug 28, 2008 11:36 AM -
Java and abap stack connection
Hello,
how to check connection b/w Java and ABAP stack.
I am getting below error :
SAP:Code area="MAPPING">JCO_SYSTEM_FAILURE</SAP:Code>
<SAP:P1>connection to partner 'localhost:0' broken / CPIC-CALL: 'ThSAPCMRCV' : cmRc=20 t</SAP:P1>
We did some upgrades of kernel and jvm and started getting this error.
Please suggestHi,
Check this threads
JCO_SYSTEM_FAILURE
JCO_SYSTEM_FAILURE
JCO_SYSTEM_FAILURE . Pls help
Regards
Ramesh -
How is the interface between the Java Stack and ABAP stack is achieved?
How is the interface between the Java Stack and ABAP stack is achieved?..Please send me the answer to [email protected]
Hi,
By interface, I assume you mean the connection between the ABAP and the Java stacks in a double stack system.
The connection from Java to ABAP is through JCo connections defined in the WebDynpro section of the J2EE start page. So Java to ABAP requests are processed through JCo.
The connection from ABAP to Java is through RFC connections defined in TA SM59. The ABAP to Java requests are processed through RFC.
Refer https://dsd.esco-salt.com/StartPage/documents/integration/3.html for detailed explanation.
The UME can be maintained in either ABAP or in JAVA depending on the persistence.
Refer: http://help.sap.com/saphelp_nw70/helpdata/en/5b/5d2706ebc04e4d98036f2e1dcfd47d/frameset.htm
Check UME data source configuration.
Some quick FAQs can be found at:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/ad47eb90-0201-0010-7cb2-ddfa5ed879ec
Hope this helps.
Best Regards,
Srividya.R -
JAVA Stack and ABAP Stack not in Sync
Hi,
when i logged into the MI Server(7.0) gonr thru the following navigation :
Administration-->Mobile Infrastructure---->Mobile components
which i click on the search button i am getting the following error
"JAVA Stack and ABAP Stack not in Sync"
Already i redeployed the sapjra.rar, still i find the error unchanged.
Any help on this would be great........
Thanks,
vijay.Hi
Refer this link
Need to Configure MI Server 7.0
As explained by veeraragavan in this link follow these steps
Following are in brief the roles required, just forward the same to your BASIS administrator.
In the ABAP Stack -Under Transaction SU01:
End User:
SAP_MI_SERVICE
Administrator / Critical Developers:
SAP_J2EE_ADMIN
SAP_MI_ADMIN
In the J2EE Stack - Under Identity Management:
End User:
No role required. You can give a role for display: SAP_JAVA_NWMOBILE_ADMIN_READONLY
Administrator / Critical Developers:
SAP_JAVA_NWMOBILE_ADMIN_SUPER
regards
Manohar
Edited by: Gouri Manohar Gadhamsetty on Jan 19, 2009 7:17 AM -
Communicate link between Java and ABAP Stack for https
I have configured https in both the java and abap stacks (we have a double stack configuration). Due to our future configuration I have changed the hostnames to fully qualified hostnames per SAP instructions.
The question I have is does anyone know what RFC destinations or JCo settings I need to change to make https complete?
I have the problem where when I fire off the Integration Builder from within the ABAP stack (SXMB_IFR) I get a straight hostname (no domain name). Where is this configured? Any help is appreciated..Check the exchange profile (Administratio tab in /rep/start/index.jsp page; you will have to enter it manually since it is throwing error from SXMB_IFR).
Regards,
Henrique. -
JAVA and ABAP stack support pakages
Hi,
I am new on installation of solution manager server.
I just install solution manager server EHP1 on windows 2003. Now I want to patch my server.
I have abap and java stack on my server. Can I use jspm to upload my new patches for both Java and ABAP stack or I should use SPAM for abap stack and jspm for java.
Thanks RezaHello Reza,
Just to clarify, Best practise is to update your kernel to the latest before you start patching in your system.
So download SAPEXE.SAR (Database independent kernel package), SAPEXEDB (Database dependent kernel package) and IGSEXE.SAR (IGS Package) from the SMP. kernel is dependent on your operating system and database and therefore make sure you download the right package otherwise you'll end up in messing up the system.
follow SAPnote # 19466 for help.
Once you are done with the kernel update then patch you Abap stack by SPAM and JAva stack by JSPM.
I hope that makes things clear.
Best Regards
NIraj -
Hi All,
I am still not clear about role/function of java and abap stack in XI.
Can anybody explain?Sireesha,
Tha ABAP stack consists of the Integration Server which in turn contains your Integration Engine and Business Process Engine.
The J2EE stack contains the Adapter Engine and your IR and ID run on the J2EE engine.
Most of XI pipelines happens in the ABAP stack.
All messsages picked by the Adapter Framework running on the J2EE engine are passed to the Integration Engine, which does the routing. The mapping program again gets executed on the Java stack and the rest of the pipeline servies are executed again on the ABAP stack and so on.
please go through links::
ABAP and JAVA in Netweaver stack
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/media/uuid/4aa47d27-0a01-0010-5db4-bb62dfc8c069?prtmode=navigate -
Ok, so this was more tedious than I thought it would be, but things actually seem to be working at this point.
Goal: Create a Dual Band network with Time Capsule (N only) and a Linksys WRTSL54GS (B/G)
Time Capsule: 1000BaseT wired, and 802.11N 5Ghz only wireless
Linksys: 100BaseT wired, and 802.11G 2.4Ghz wireless
Airport Utility 5.3.1
Time Capsule v. 7.3
I set Time Capsule up first, following the step by step directions for "Create a wireless network"
802.11N only, 5Ghz
WPA2 Personal
DHCP 192.168.1.1 (kinda important)
This worked fine-tested on a C2D iMac, both thru ethernet and wirelessly thru N. Time Machine backed up fine.
Now the tricky part, configuring the Linksys.( I just want to mention I had to reset this thing completely about 10 times to get it to work, using a miniscrewdriver)
Starting with a freshly reset Linksys, I connected from my MacBook ethernet port to one of the Linksys ethernet ports (Not the WAN)
I disabled Airport
I logged in to 192.168.1.1 using blank for login, admin for password (default for Linksys)
I did the following:
1) Confirmed Internet Connection Type was "Automatic Configuration-DHCP"
2) Changed Network Setup to "DHCP Server-DISABLED"
3) Turned off the Firewall settings in Security (not sure if this is necessary)
4) Changed the Operating Mode from "GATEWAY" to "ROUTER"
5)Changed the SSID to "LinksysG_ONLY" or something like that
After each one of these steps, I had to save the configuration, thru the Linksys browser interface-which blows.
6) Finally, I changed the Local IP Address of the Linksys from 192.168.1.1 to 10.0.1.251 (thanks to Henry B. for that)
7) And....I no longer had access to the Linksys at all! This stumped me for a while, until...
8) I checked my Ethernet settings (in System Preferences/Network): 192.168.1.1 was set as default router address. But my Router (at least for configuration purposes) was now 10.0.1.251, so it could no longer find it.
9) So I added a new Ethernet port (using the "+" sign), called it Ethernet-Linksys. Set it to Manual. Put in an IP of 10.0.1.250, and a Router IP of 10.0.1.251.
10) I got access to the Linksys setup page again! (Note: I'm sure there is an easier way to do this, but this is how I got mine to work )
11) I set up WPA security again, set it to an unused channel (2 in my case), mixed b/g network.
12) Finally, I moved the ethernet cable from my MacBook directly to one of the ethernet ports on the Time Capsule. I did NOT hook up the other end to the WAN on the Linksys (which for some reason I had done 100 times before) I left it in one of the 4 ethernet ports on the Linksys. Repeat, the WAN (ethernet) port remains empty.
13) I then turned Airport back on the MacBook, connected to "LinksysG_ONLY", and...I was online. And everything seems to work.Hi kjk et al,
I've been searching the boards for something like what you have described in such nice detail. Before Time Capsule, I used a Netgear g router connected to the cable modem and an older Apple base station connected to the Netgear as a bridge. I removed the Netgear and set up my Time Capsule as the primary. The newer computers in my network can access the Time Capsule, but the old Dell with a 802.11g wireless card cannot. I don't remember seeing where I could access TC to change a setting of "N only" or b/g, but I am guessing that it is running N.
I tried to follow the steps you used for Linksys. The pre-step 1 thing, resetting it "10 times to get it to work" - how do you know when it is really reset? With Netgear plugged into electricity, I stuck a paper clip into the hole labeled on the diagram as "restore factory settings" and watched the color of the IO icon change from green to amber to green. I did it again for good measure.
I plugged ethernet from PowerBook G4 into Netgear not-WAN ethernet ports (like your MacBook to Linksys). I disabled Airport. Using Safari, I logged into 192.168.0.1 and got to the Netgear SmartWizard configuration assistant. It says, "No Internet Connection Detected. Please check the connections to the Internet WAN port and cable/DSL modem" - so I looked at your instructions but see no mention of connecting the router to the modem.
Trying to follow your numbered steps...
1. In SysPrefs: Network, Location showed Automatic, Configure showed Using DHCP.
2. I don't see an option in Network to "DHCP Server-DISABLED", but I can choose Configure: OFF. I clicked Apply but browser still gives same message.
I don't know how to continue the steps. -
System time for Java Stack and ABAP Stack of PI
HI,
We have a scenario in which we have a synchronous flow of data. In the forward flow we have used field UZEIT in an RFC Lookup to register the inbound time and in the reverse flow we have used current time function of SAP PI mapping. PI time is the local time of the server, However UZEIT is 4 hours ahead compared to PI time.
Both the Java and the Abap stack are installed on the same server.
Kindly let us know the reason for the difference in time on both the stacks.
Regards,
Milan ThakerHi,
Yes I am refering to the System->Status time in ABAP Stack. Could you please tell me where can I check the System time of JAVA stack. I got one XML file in UME which refers to some timestamp in com.sap.security.core.usermanagement but I failed to locate this field. Please let me know where can I find the Java stack time and how can that be synchronized with ABAP.
Also, is there any time zone settting in JAVA for UTC , the way we have in ABAP
Regards,
Milan Thaker -
Different time in show clock and show calendar
Hi all,
I am having problem with figuring out how to adjust time between show calendar and show clock.
Basically time difference between this commands is roughly 40 minutes.
Please look on the screenshot:
Also my router configurations is:
! No configuration change since last restart
! NVRAM config last updated at 05:26:42 GMT Mon Dec 8 2014
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname RtrPod1
boot-start-marker
boot system usbflash0:c2800nm-advipservicesk9-mz.124-24.T1.bin
boot-end-marker
logging message-counter syslog
enable secret 5 $1$kABI$oyiPktODUDz4Ahdz7pCma0
no aaa new-model
clock timezone GMT 13
clock summer-time GMT recurring
clock calendar-valid
no network-clock-participate wic 1
network-clock-participate wic 2
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.110.0.1 10.110.0.10
ip dhcp excluded-address 10.115.0.1 10.115.0.10
ip dhcp pool Data
network 10.110.0.0 255.255.255.0
default-router 10.110.0.1
ip dhcp pool Voice
network 10.115.0.0 255.255.255.0
default-router 10.115.0.1
option 150 ip 10.115.0.1
no ip domain lookup
no ipv6 cef
ntp server 192.189.54.33
multilink bundle-name authenticated
voice-card 0
crypto pki trustpoint TP-self-signed-1408351535
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1408351535
revocation-check none
rsakeypair TP-self-signed-1408351535
crypto pki certificate chain TP-self-signed-1408351535
certificate self-signed 01
3082023F 308201A8 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31343038 33353135 3335301E 170D3134 31323037 31363236
34325A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 34303833
35313533 3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
81009EEF ADD1297E 7CD9BE3E 5BD3798D 10831172 0E025CB9 C7E57188 006DA7E1
E7B1D9A9 73EC5C53 841413DE E3E4AECD BC80C3D1 CC6BA113 B91CC736 16AF1576
F37F8437 C9577F4A 0AE72460 1E524E06 74E8DD39 E6952E1F 85547E71 1AD3DE5A
6DCB12E9 BD953716 13B41148 320EC307 9E45B084 80D0591A E49E8AE2 D87C0716
86430203 010001A3 67306530 0F060355 1D130101 FF040530 030101FF 30120603
551D1104 0B300982 07527472 506F6431 301F0603 551D2304 18301680 14880D89
51BCB633 B6F32385 71C9A39E 72149EAF 99301D06 03551D0E 04160414 880D8951
BCB633B6 F3238571 C9A39E72 149EAF99 300D0609 2A864886 F70D0101 04050003
8181001C 63A1BE6C BC96B738 05446ABC ACE19FBF 0054F6B5 100BA758 9A48FAF8
34B65325 3A374B08 2D8919BF 09ED604F 2F1B7A33 C25CFC7E 6DD55DA6 02CD7E78
4272ADF7 15158EDE 4A1115A9 06BBDA02 E65E5AC8 559103C4 98EF7371 20568663
ADF16711 60F8C5E0 ECDB5321 B3ABB8D5 2F42F19E 07D65ADF BABCDE63 50B43773 87AD10
quit
username student privilege 15 secret 5 $1$o8qC$cxUuwRjEtfvasjtjfNZAv/
archive
log config
hidekeys
controller E1 0/1/0
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
interface GigabitEthernet0/0.110
description Data VLAN
encapsulation dot1Q 110
ip address 10.110.0.1 255.255.255.0
interface GigabitEthernet0/0.111
description Management VLAN
encapsulation dot1Q 111
ip address 10.111.0.1 255.255.255.0
interface GigabitEthernet0/0.115
description Voice VLAN
encapsulation dot1Q 115
ip address 10.115.0.1 255.255.255.0
interface GigabitEthernet0/1
ip address dhcp
duplex auto
speed auto
interface Serial0/0/0
no ip address
shutdown
clock rate 2000000
interface BRI0/2/0
no ip address
interface BRI0/2/1
no ip address
interface Service-Engine1/0
no ip address
shutdown
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.15.1
ip http server
ip http authentication local
ip http secure-server
ip http path usbflash0:/gui
tftp-server usbflash0:phone/7942-7962/apps42.8-4-1-23.sbn alias apps42.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/cvm42sccp.8-4-1-23.sbn alias cvm42sccp.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/jar42sccp.8-4-1-23.sbn alias jar42sccp.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/cnu42.8-4-1-23.sbn alias cnu42.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/dsp42.8-4-1-23.sbn alias dsp42.8-4-1-23.sbn
tftp-server usbflash0:phone/7942-7962/term42.default.loads alias term42.default.loads
tftp-server usbflash0:phone/7942-7962/term62.default.loads alias term62.default.loads
tftp-server usbflash0:phone/7942-7962/SCCP42.8-4-2S.loads alias SCCP42.8-4-2S.loads
tftp-server usbflash0:Desktops/320x196x4/big.png
tftp-server usbflash0:Desktops/320x196x4/small.png
tftp-server usbflash0:Desktops/320x196x4/List.xml
tftp-server usbflash0:Ringtones/Analog2.raw
tftp-server usbflash0:Ringtones/AreYouThere.raw
tftp-server usbflash0:Ringtones/AreYouTheref.raw
tftp-server usbflash0:Ringtones/Bass.raw
tftp-server usbflash0:Ringtones/CallBack.raw
tftp-server usbflash0:Ringtones/Classic1.raw
tftp-server usbflash0:Ringtones/Classic2.raw
tftp-server usbflash0:Ringtones/ClockShop.raw
tftp-server usbflash0:Ringtones/Drums1.raw
tftp-server usbflash0:Ringtones/Drums2.raw
tftp-server usbflash0:Ringtones/FilmScore.raw
tftp-server usbflash0:Ringtones/HarpSynth.raw
tftp-server usbflash0:Ringtones/Jamaica.raw
tftp-server usbflash0:Ringtones/KotoEffect.raw
tftp-server usbflash0:Ringtones/MusicBox.raw
tftp-server usbflash0:Ringtones/RingList.xml
tftp-server usbflash0:Ringtones/DistinctiveRingList.xml
tftp-server usbflash0:Ringtones/Piano1.raw
tftp-server usbflash0:Ringtones/Piano2.raw
tftp-server usbflash0:Ringtones/Pop.raw
tftp-server usbflash0:Ringtones/Pulse1.raw
tftp-server usbflash0:Ringtones/Ring1.raw
tftp-server usbflash0:Ringtones/Ring2.raw
tftp-server usbflash0:Ringtones/Ring3.raw
tftp-server usbflash0:Ringtones/Ring4.raw
tftp-server usbflash0:Ringtones/Ring5.raw
tftp-server usbflash0:Ringtones/Ring6.raw
tftp-server usbflash0:Ringtones/Ring7.raw
tftp-server usbflash0:Ringtones/Sax1.raw
tftp-server usbflash0:Ringtones/Sax2.raw
tftp-server usbflash0:Ringtones/Chime.raw
tftp-server usbflash0:Ringtones/Vibe.raw
control-plane
voice-port 0/2/0
voice-port 0/2/1
voice-port 0/3/0
voice-port 0/3/1
voice-port 2/0/0
voice-port 2/0/1
voice-port 2/0/2
voice-port 2/0/3
voice-port 2/0/4
voice-port 2/0/5
voice-port 2/0/6
voice-port 2/0/7
shutdown
mgcp fax t38 ecm
mgcp behavior g729-variants static-pt
telephony-service
max-ephones 5
max-dn 10
ip source-address 10.115.0.1 port 2000
load 7962 SCCP42.8-4-2S
max-conferences 8 gain -6
web admin system name webadmin secret 5 $1$MafG$7vShhmB.Tlfy22rnE88BK1
transfer-system full-consult
create cnf-files version-stamp 7960 Dec 08 2014 05:26:39
line con 0
exec-timeout 120 0
password cisco
logging synchronous
login
line aux 0
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
exec-timeout 120 0
password cisco
logging synchronous
login local
transport input telnet ssh
line vty 5 15
exec-timeout 120 0
password cisco
logging synchronous
login local
transport input telnet ssh
scheduler allocate 20000 1000
end
And my switch configuration is:
! No configuration change since last restart
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname SwPod1
boot-start-marker
boot-end-marker
enable secret 5 $1$LDXy$1QdQ73kHv.8sQenQNMq19.
no aaa new-model
clock timezone GMT 13
clock summer-time GMT recurring
system mtu routing 1500
authentication mac-move permit
ip subnet-zero
no ip domain-lookup
crypto pki trustpoint TP-self-signed-2133227136
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2133227136
revocation-check none
rsakeypair TP-self-signed-2133227136
crypto pki certificate chain TP-self-signed-2133227136
certificate self-signed 01
3082023F 308201A8 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32313333 32323731 3336301E 170D3933 30333031 30303030
35385A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 31333332
32373133 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B71D E6CDD16E D6FEDB25 EC976368 7925A2F8 75EE3EF0 D4C371DA 4B5539BB
E3A9552F DE35F37B 45A2C5C4 30FEF8D7 C3C5C489 C08C8A90 B415D331 F4653100
DC1E0ECE D93B2BF5 339C7B3A D170B80A AFEE8DA9 A82263F9 6324F8FA 94BB253E
7B0B45D6 81E39078 1607DED1 85C69650 AB7D7419 96604F65 D9204BC8 1BC259BB
6D0B0203 010001A3 67306530 0F060355 1D130101 FF040530 030101FF 30120603
551D1104 0B300982 07537750 6F64312E 301F0603 551D2304 18301680 14C16878
2994DA55 82E0FAD0 046CED6D 0EBDA0EE AA301D06 03551D0E 04160414 C1687829
94DA5582 E0FAD004 6CED6D0E BDA0EEAA 300D0609 2A864886 F70D0101 04050003
81810090 C6829BAE 9B2A3A31 2A32C1FB AC7946E5 287A43B6 EC9F31D5 13296A2E
1810E5EB 2503617C C4CCDF9D 421E2372 E94A8BFA D73AB361 46BF80E4 B2C3E828
6DB62E7F DE5E0F6F B93A885E 3A5E13CA 6D95426C 9494C22D 005E8BC9 C6C012D5
DF186CFB 194BC416 89566F98 0C21CC79 D477022C A4845D94 EE0FC299 7C7710C5 32F314
quit
spanning-tree mode pvst
spanning-tree etherchannel guard misconfig
spanning-tree extend system-id
vlan internal allocation policy ascending
interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/2
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/3
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/4
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/5
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/6
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/7
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/8
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/9
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/10
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/11
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/12
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/13
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/14
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/15
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/16
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/17
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/18
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/19
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/20
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/21
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/22
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface FastEthernet0/23
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/24
switchport access vlan 110
switchport mode access
switchport voice vlan 115
spanning-tree portfast
interface GigabitEthernet0/1
interface GigabitEthernet0/2
interface Vlan1
no ip address
shutdown
interface Vlan111
ip address 10.111.0.2 255.255.255.0
ip default-gateway 10.111.0.1
ip classless
ip http server
ip http secure-server
ip sla enable reaction-alerts
line con 0
exec-timeout 120 0
password cisco
logging synchronous
login
line vty 0 4
exec-timeout 120 0
password cisco
logging synchronous
login
line vty 5 15
exec-timeout 120 0
password cisco
logging synchronous
login
ntp clock-period 36028575
ntp server 10.110.0.1
end
Any help will be highly appreciated.Have you tried using "ntp update-calendar"?
-
Relation and Difference between Java Stack and ABAP Stack
Hello,
This is harsha, i am new to XI.
i want to know the details of<b> java stack</b> and <b>ABAP stack</b> ?
how they are <i>related</i> to each other ?
which plays a major role at which time, can any one give a details explanation on this
thanking you with anticipation
regards
harsha
Message was edited by:
harsha vardhanHi ,
Integration related will be done in Integration Engine ,, it means in ABAP Stack..
I mean ..
Integration Engine and Business process Engine on ABAP Stack..
Rest of all components are on JAVA Stack..
see the below links
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/30f8bd90-0201-0010-dd9a-c8a7f52c47aa
Regards
Chilla
Maybe you are looking for
-
Exchange 2013 does not show AD people pictures
Hello, Exchange 2013 is configured in hybrid mode with exchange online. Majority of the mailboxes are located in Office 365. Also we have exchange 2007. When I open mailbox located on exchange 2013 and searching for people- I don't see their pictures
-
PSE10 not writing dates to files consistently
I asked essentially this question on Elements Village a few days ago. No responses as yet, so I thought I'd try here... In PSE10, I have many photos scanned to TIFFs. In the Organizer, I set the dates for these photos to match when the original phot
-
AOA How to remove the text from cells of JPanel. Just to refresh the GUI. regards
-
ICal preferences on my Mac not available on MobileMe?
I have iCal on my Mac set up to automatically generate an alarm and a message 24 hours before new events and to-dos. When I add new items to iCal on MobileMe, those default settings aren't available. When iCal syncs, the items I added on MobileMe don
-
Create a file xml using dbms_xmldom
i'm using dbms_xmldom to create a file xml. i use to create a node this line: IV_element:= dbms_xmldom.createElement(doc,'CATEGORIA'); dbms_xmldom.setAttribute(IV_element, 'natura','prova'); IV_node:=dbms_xmldom.appendChild(III_node,dbms_xmldom.makeN