PI Self Test for NetWeaver

In running the PI Self Test for NetWeaver, I am getting 22 out of 24 of the steps to successfully execute. We are using NW 7.1 for PI with Ehnacement Pack 1 and stack 6. The steps not completing successfully are "Check Web Services setup" and "Check whether blocked bgRFC queues exist on IS client".
The error message for the "Check Web Services setup" is "Execution of Function SRT_TECHNICAL_SETUP_CHECK ends with an error (cause:bgRFC destination is not operational, error code:000)."
The error message for the "Check whether blocked bgRFC queues exist on IS client" is "Execution of Function SRTUTIL_CHECK_QUEUES ends with an error (cause:bgRFC Inbound Destination cannot be determined., error code:000)."
I have looked in SBGRFCCONF and SM59 and find that the users are defined and seem to have the proper roles. Has anyone encountered these on the PI Self Test for NetWeaver and - if so - where should I be checking for my mistake.

Hello
The 2 steps fail because SOA runtime/configuration tools are not configured, and the bgRFC which is only used by SOA web services is also not configured. If you don't use SOA scenarios and only PI functionality you can ignore these error messages.
Check note #1286149 Configuration Wizard: PI Self Test for NetWeaver, for further details.
Regards
Mark

Similar Messages

RWB - Integration Engine self test - web service security and proxy

Hi,
I am working with a new installation of PI 7.0. In the runtime workbench, under self test for integration engine, there is this error/warning:
""Details for 'Is Web service security available?'
Communication error: Proxy calls are not permitted on sender or receiver side on the IS (client)""
What exactly is the problem? Is there any additional configuration needed within PI to use proxies? We do not have the cryptographic toolkit installed. Is that nesseccary to work with proxies? We have done several other scenarios with RFC, MAIL, HTTP, etc and they work fine. If anyone else had this problem and managed to fix it, please let me know..
Thanks,
Lasya

You can ignore this error. It is simply a warning that says message level security has not been configured. Without message security too, you can do proxy communication.
But, if you want to configure messag level security, go through XI Config guide section 12.4.
Message was edited by: Jay

Software Updates for Remote PXI System/DAQ-mx Self Test

1) In MAX, I'm attempting to run the Labview Realtime Software Installation Wizard. When I select the software for install, I get an error "Cannot Process Install because other Dependencies are required: Labview RT 7.1.1". What should I do to correct the problem? I'm trying to update both DAQMx and Traditional DAQ from 7.2 to 7.3. The wizard actually indicates that the remote system only has 7.2, and that it sees that 7.3 is available.
2) Also in MAX in the Remote System Tree, I get an error when trying to perform a self test on my PXI-6025 card, or when I attempt to reset it. The error code is 88705. I noticed on another post that there might be the need to perform a repair of the installation. This was done for both DAQMx and Tranditional DAQ, neither of which fixed the problem.
3) In MAX I have used the Tools>>Traditional NI-DAQ Configuration>>Remote DAQ Configuration to configure my PXI-6025 DAQ channels, accessory, device #, etc. I then proceed to run a Analog Input VI on the remote system by correctly targeting it and selecting i.e. channel 0. No errors occur. However when I try and select "Browse" under the channel control, the "Select Names" window pops up empty. I would assume that this window would pop up with the DAQ channel names assigned during the channel configuration of the PX-6025??? Whats missing here?
Thanks
Pete.

Hi Pete,
I'm assuming you are using LabVIEW RT 7.1, since that is a requirement for using DAQmx. Here are my responses for your three issues:
1) You are correct in assuming you can upgrade the DAQ drivers in the manner you outlined, normally that works fine. However, as the following KnowledgeBase points out, the list of dependencies vary for different installs.
http://digital.ni.com/public.nsf/websearch/F5D80FBE806B4B9D86256F0F005630CF?OpenDocument
Do you have LabVIEW RT 7.1.1 installed, which appears to be the required dependency? If not, you may download this from ni.com>>Drivers and Updates
http://digital.ni.com/softlib.nsf/MainPage?ReadForm&node=132010_US
If so, but the problem persists, please post all versions of your software so I can determine where the incompatibility lies.
2) After we take care of upgrading the DAQ drivers, let's see if the 88705 error goes away, it might take care of it.
3) Again, all the steps you described are correct. It might be that all these problems are related and due to a bad install of NI-DAQ.
When a number of software issues like this arise all at once, it might be best to just re-format the controller and perform a fresh install of everything. Often times that will correct the erroneous behavior.
Regards,
Jeff M.
Applications Engineering
National Instruments

SAP EhP1 SPS6 for NetWeaver 7.0 - tp status 230

While installing SAP EhP1 SPS6 for NetWeaver 7.0 in PBW
(BI production system) the process fails at phase
MAIN_NEWBAS/TABIM_UPG - with tp status 230 and unresolved requests in
buffer.
Anyone has a clue ?
Best regards,
Roger
PHASES.LOG
1 ETQ201 Entering upgrade-phase "TABIM_UPG" ("20110716054322")
4 ETQ399 Set environment for standard connect:
2 ETQ367 Connect variables are set for standard instance access
4 ETQ399 System-nr = '61', GwService = 'sapgw61'
4 ETQ399 Environment variables:
4 ETQ399 dbs_db4_schema=SAPR3
4 ETQ399 auth_shadow_upgrade=0
1 ETQ206 Executing pre-phase DB specific actions.
1 ETQ200 Executing actual phase 'MAIN_NEWBAS/TABIM_UPG'.
1 ETQ399 Phase arguments:
2 ETQ399 Arg[0] = 'TABIMUPG.BUF'
2 ETQ399 Arg[1] = 'TABIMUPG.TPP'
2 ETQ399 Arg[2] = 'TABIMUPG.TP0'
2 ETQ399 Arg[3] = 'TABIMUPG.ELG'
2 ETQ399 Arg[4] = 'XPRASUPG.BUF'
2WETQ399 tp terminated with status 230
4 ETQ380 computing toolpath for request "TP_ACT_ON_NEW_BUFFER"
4 ETQ381 request "TP_ACT_ON_NEW_BUFFER" means "act on the tp buffer,
new format"
4 ETQ382 translates to group "R3UP_TOOL_GROUP_SYS"
4 ETQ383 translates to path "/usr/sap/PBW/SYS/exe/run"
2 ETQ399XAnalyze summary error logfile TABIMUPG.ELG and remove all error2 ETQ399Xconditions as described in the upgrade manual
1 ETQ207 Executing post-phase DB specific actions.
4 ETQ010 Date & Time: 20110716054327
SAPehpi.log
CURRENTPHASE MAIN_NEWBAS/TABIM_UPG
...started at 20110716054322
...begin processing at 20110716054322
INFO: Nothing has been done in TABIM_UPG.
..times self: 0.130000/0.060000 usr/sys, children 1.110000/0.000000
usr/sys.
..finished at 20110716054327 with status UNRESOLVED REQUESTS IN BUFFER.
Error message set: 'Unresolved requests in buffer PBW
Check logfiles 'TABIMUPG.ELG'
and '/BWIASP1/usr/sap/PBW/put/EHPI/abap/log/SAPehpi.ECO''
...begin dialogue at 20110716054328

Added *allobj to PBWOFR user profile and repeated the phase with success.

To check ink levels I am told to print self test. page from cpu or printer.

There is no way to print a test page on my" psc 2410 all in one" connected to a HP cpu with Win 7, 64 bit. Is there a workaround/

The page here shows how to print a self-test report from the front panel, but it does not appear to have ink level information. I have not used a PSC 2410 for years, but the following may give you what you need: press the # and * buttons together on the printer. The screen will say "Enter special key combination". Press 1 2 3. This should bring up a service menu. Use the right arrow button repeatedly to bring up a "Special Reports" screen, OK, then right arrow to select "Cartridges" or some similar, then press OK. A page will print with ink level information shown about the middle of the page.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Ipod nano starts with a self-test after sleep

My new Ipod nano runs a kind of self-test if it was at sleep for a couple of hours.
Does this have to be? If not how can I determine specifically what is wrong? Thanks

Gert,
When iPods are not used for a period of 24 hours of more then they go into something called "Sleep Mode" or "Deep Sleep".
You'll see the Apple logo when you try to turn your Nano back on which is normal, you are "waking up" the iPod.
I've never heard or seen of such self-test, is it still on self-test? Or you want suggestions on how to get out of that?

Hard Drive failed both postive read and smart short self test

Hello, my Lenovo Think Pad's Hard Drive failed both targeted read test (error code WHD20-HJF) and the smart self test (error code WHD16-KPY). I admit that I'm an older user and I have no idea what this means and what is the possible fix for it.
I am open to all suggestions;
THANKS,
Octavious ONeal

Hi, Octavious
When the hard drive fails those tests, it's an indication that the drive is dying. It's recommended to back up any valuble data on the hard drive and then replace it soon. The drive may still work for a little while, but it will likely stop working sometime soon.
Hope it helps,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

HDD replaced with SSDHDD & Drive Self Test failed hardware scan by LSC

Hello! Happy new year!
I bought a new SDDHDD instead of the HDD that came with the laptop when I bought it because it was faulty.
I want to make sure that the new drive isn't faulty when running the hardware scan using Lenovo Solution Center (LSC), I got this result code: WHD01V000-HK9V1D - Warning for the SMART Drive Self Test. However I tried testing using HD Sentinel and SeaTools but they showed no errors.
Note: I'm taking LSC seriously because it showed warnings then critical alerts before my first HDD failed so I don't want to ignore it.
Please let me know what it means and if I should worry or how to fix the problem? Or does it simply not support SDD?
Thanks for reading this long message! (Sorry)

Hi, quocphong
It sounds like the hard drive is running okay overall, but it has some bad sectors in it. You will not be able to read or write to these sectors. That being said, I would first try running a ChkDsk on the hard drive and see if any of the sectors can be repaired. To run a ChkDsk, go to Computer and right-click on the C: drive and select Properties. Navigate to the Tools tab and select the box that says Check now... This should scan the drive for errors and attempt to fix them if possible. The test can take a while, so I would do it when you will not need access to your computer.
If the test is not able to fix the errors, then I would contact Lenovo at 120-11072 (Toll Free) or +(84) 8 3521 8000 (Standard Charges Apply) and discuss a hard drive replacement with them. As for Windows, you will need to ask for recovery discs as well. Lastly, I would backup everything on the current hard drive so that it is not lost.
Hope it helps,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

Linkage Error in Mapping and Operation mapping testing for Synchronous in NWDS

Dear Experts,
Hope you all are doing fine..
I am working in a synchronous scenario Proxy via SAP PI 7.4 to JAVA Application supporting JSON.I wrote JAVA program to convert JSON to XML and while performing test for the JAVA mapping in response structure at Operation Mapping,I am receiving following error..
LinkageError at JavaMapping.load(): Could not load class: json2xml/bin/pack/EsrJson2Xml
java.lang.NoClassDefFoundError: json2xml/bin/pack/EsrJson2Xml (wrong name: pack/EsrJson2Xml) at
java.lang.ClassLoader.defineClass1(Native Method) at java.lang.ClassLoader.defineClassCond(ClassLoader.java:735)
at java.lang.ClassLoader.defineClass(ClassLoader.java:716) at java.lang.ClassLoader.defineClass(ClassLoader.java:537)
at com.sap.aii.ib.server.mapping.execution.MappingLoader.findClass(MappingLoader.java:195)
at java.lang.ClassLoader.loadClass(ClassLoader.java:372) at java.lang.ClassLoader.loadClass(ClassLoader.java:313)
I followed some of discussions for the Linkagae error http://scn.sap.com/thread/1418477 but could not help..
Following are details of my NWDS and PI server:
SAP NetWeaver Developer Studio
SAP Enhancement Package 1 for SAP NetWeaver Developer Studio 7.3 SP10 PAT0000
Compiled the project with JAVA SE-1.6 as well as 1.5
SAP PO 7.4 Java Only , Release: NW731CORE_10_REL
SP: 05 JDK: jdk16 Latest Change: 353688
I have taken care to export all the Jar files used in NWDS to be exported and then imported as Archived files in PI server.
But could not see the 5 jar files in ESR. I hope there is some issue with name as can see in the log.Can the issue be solved?
How to test the Operation mapping for Synchronous Message in NWDS?
Regards
Rebecca

Dear Hareesh and Experts,
I resolved the issue by doing the below steps.
1. Downloaded the JDK5 and updated the Java console i.e. JRE 15.
2. I had created this project using the JAVA Compiler with JAVA SE1.6 initially. Changed this to 1.5 in the Properties of the Project.
3. Uploaded the project again in ESR Imported Archive.
The issue is solved.
Thanks a lot for all your inputs.

XI 2.0 WorkBench File Adapter Self-Test Error

I have installed the file adapter on our XI serve and when I perform the Self-Test I get the following error HTTP request failed. Error code: "401". Error message: "Authorization Required". I have the user XIRWBUSER defined to the Adapter Engine. What else am I missing?

Hi Dan,
You are thanking a poster for his answer.
Please next time also give him points.
See: /people/mark.finnern/blog/2004/08/10/spread-the-love
This time I did it for you.
Remember: When you ask a question you also assume the responsibility to assign points.
Please check your other questions and if the answers were good.
Spread the love and give some points.
Thanks in advance, Mark.

PCI-MI0-16XE-50 Failing Self-test

I am using a PCI-MI0-16XE-50 which is failing the self-test in MAX 3.1.1.3004. I have used the E Series Diagnostic Utility which gives the error "Error 10809 occurred at cwdaq: Starting DAQ operation Attempted to start a pulse width measurement with the pulse in the phase to be measured (e.g., high phase for high-level gating)." Windows XP detects the device fine, as does MAX. The obvious answer is that the device is broken, but is it feasible or economical to have the device repaired? What tends to cause this type of problem and/or how can it be corrected?
Thanks,
Brandon

Hello C.
You will need to contact National Instruments for a quote for repairing
you board. If you bought less than a year ago, it may still be under
warranty in which case it would not cost you anything to repair.
However, I would suggest in case you need to pay for repair to consider
getting one of the new improved and more performent yet low cost M Series devices.
Hope this helps.

Help! Ipod doing some crazy self test thing and now wants some remote test.

well i turned my ipod mini on this morning to plug into my headunit but it came up with some screen about memory and restarts and selftests etc (i couldnt get out of this screen) anyways i mustve pressed something and it went through this self test then started prompting me to do certain things (like check scrolls etc) this was okay then it came to a remote check. i dont have a remote for my ipod. It says i need to check volume, pause, play, next song etc and nothing i press on my ipod does anything. Can anyone help??? what should i do??
Thanks all.

thanks for reply but i tried that earlier and ipod wont respond to any commands from ipod buttons.

PCI-6221 fails self-test in MAX but device manager says it's working

Hi everyone,
I bought a few PCI-6221 (37-pin) data acquisition cards and have been able to get one to work but 3 others don't work.
Device Manager sees them and says they work. MAX sees them and when I run Self Test, they fail with error number
-50002. Motherboards in non-working systems are PC Chips M957G and P25G. OS is Windows XP Pro with SP2.
I already tried uninstalling SW and the board, reinstalling SW and the
board...autodetect etc works fine. I even reformatted
the HD on one of the computers and reinstalled the OS. Anyone have any ideas? Thanks in advance. Halden
[email protected]

Thanks Tom for your suggestion to try NI-DAQ 8.0. I just saw it today. Yesterday,
I was able to isolate 3 PCI-6221-37 boards as defective because they all wouldn't work in another computer while
one other identical model card did work in that same computer. I called to arrange to return them to NI and learned
that for these 3, I needed NI-DAQ 8.0. The fourth one was okay
with NI-DAQ 7.5. Apparently, this was a known problem.
I wish NI would have simply notified me that my boards would
not work with the software sent with them and sent the NIDAQ 8.0 CD as soon as they knew rather than have me
waste a day of my engineering time trying to figure it all out. Booo NI.
One of the boards has worked for almost a day under NIDAQ 8.0. I was able to make some progress on the
system I am building. But then it stopped working. LabVIEW
(version 7.0 executable) programs would not open completely
or would open slowly. One that accessed the COM port only (no
data acquisition) did work. MAX opened very slowly or not at all
and when I click on
Devices and Interfaces, the hourglass is up for a long time and finally the + icon goes away indicating that MAX is not
aware of any devices being present. The Windows Device Manager says the board is present and working. Windows
Task Manager lists LabVIEW Runtime and MAX when only MAX is open and indicates that MAX is Not Responding.
I shut down the computer, removed the PCI-6221 board, booted it up again, and MAX is the same way. I uninstalled
MAX and NI-DAQ LabVIEW 7.0 support and then reinstalled them.
Now the MAX loading window is up for more than a minute and NIMAX.exe is listed in Task Manager's processes. After
the first minute, LabVIEW Runtime appears in the Task Manager's
Applications list. After a while longer, the MAX window finally
opens
and MAX is listed in the Applications. I click on the + icon by Devices and Interfaces in MAX and the hourglass appears
and Windows Task Manager says MAX is Not Responding. Eventually, the + icon and the hourglass go away and
the Task Manager lists LabVIEW Runtime and MAX as Running.
I shut the computer off for several minutes, started it up again, and MAX is still takes a long, long time to open.
I haven't put the PCI-6221 card back in because MAX still isn't working.
What do you suggest I do next?
Thanks
Halden

Rosettanet Self Test Kit and XI

Hi,
We have developed some Rosettanet scenarios and now recently installed the Rosettanet Self Test Kit.
But we are finding it a bit confusing to link both XI and STK. How do we actually use the STK to test the scenarios with XI ?
ShaBZ ~~

I found this from one of the threads, a reply by Sam Raju;
>>>>>>
Part I. Test Using STK
In your XI ID:
1) Define both the parties 1) Shipper(Your Partner) 2) Receiver(Your company) with identifiers like DUNS Number.
2) In ID goto>Tools>Transfer Integration Scenarios from IR-->select the scenario "PIP3B2_Receiver" from the drop down list.
3) Follow the 4 steps in the config wizard.
4) While creating your CC, create it from the channel template delivered with the RosettaNet BP.
4.1) Specify the URL for STK which should be in the following format
http://<STK Server>:<port>/rosettanet/servlet/listenerServlet?userId=<Party Name> <b>>> the server is my ip but then what is the port ? Also i am using the default user TesterA so is it the <Party Name></b>
4.2)In the location fields, enter your location and your partner location. <b>>> your location and partner location -> can anybody elaborate ?</b>
In your STK
1) Start the RosettaNet STK.
2) enter the UserID<Partner Name in XI>
3) Select the Test Scenario, 3B2V01.01-AdvanceShipmentNotification-0001-Scenario-Shipper
4) Enter Global Business ID(DUNS Number) and Location ID for both the partners. These fields should be same as in your R/3 Party configuration.
5) Enter the URL as follows:
http://<XI Server:<J2EE_Port>/MessagingSystem/receive/RNIFAdapter/RNIF
If everything is configured correctly as mentioned, you should be able to test your single-action scenario.
~~~~~~~~~~
We have developed scenarios for PIP3A4's and 3C3's in XI and need further help to test it.

EHP1 for Netweaver Mobile 7.1 available or not?

I am trying to do a install of Netweaver 7.1, and for that reason I would like to have the latest version available. According to the installation and media guides, there should be a Install Master and Kernel 7.11 available but I am unable to locate this in the software distribution center. I can find it for Netweaver PI 7.1, but not for Netweaver Mobile. Anyone who knows more about this?
I could of course install 7.1 and then the EHP1 as an upgrade, but I already installed SQL Server 2008 and NW 7.1 can not be installed directly on MSSQL 2008, so I thought it woudl be easier to just make one install and save a lot of time and extra steps.

I have to come back to this topic, because of a reply I got in another thread some time ago from Mr Stefan Wawrzinek:
"SAP NetWeaver Mobile Always Connected is supporting Stylesheets with NetWeaver 7.1 EHP 1."
My goal by installing Netweaver 7.1 Mobile is to test the "Always Connected" functionality with mobile devices. The tests I have done with Netweaver 7.0 are very disappointing. Either I get good performance but absolutely zero control over the look & feel (using parameter PieClient), or I get terrible performance but a good looking interface (stylesheets and javascript too heavy for mobile devices).
So it seems I will anyway have to wait for EHP1. But what is puzzling me is the fact that there is no Java application server in Netweaver Mobile 7.1. Does that mean that SAP now supports the parameter PieClient for mobile-compatible rendering of HTML also for ABAP WebDynpro applications? With NW 7.0, it was necessary to use Java WebDynpro to use the PieClient parameter.
Any insight greatly appreciated!

PI Self Test for NetWeaver

Similar Messages

Maybe you are looking for