PI2.1 3rd Party devices

Hi,
I have recently installed a HA pair of PI2.1 NCS appliances and so far so good.
I have a number of 3rd party device that I would like to add.
I have uploaded the specific MIB's for these devices and created Custom SNMP templates to use to monitor them. These templates have been deployed via "Monitoring Deployment" on the 3rd party devices.
The question I have is where can I now see the detail that PI is retrieving when it SNMP polls these 3rd party devices using the custom template.
I would have thought it would be visible in the Device Work Centre when you click on a device, like it is with the Cisco ones but nothing else is showing except for the usual IP address, product family etc  information.
Any ideas ?
cheers
Rich

Changing the local ssh client to v2,1 doesnt work.
You need to change /etc/ssh/ssh_config
# Protocol 2,1
>>> comment out
not the sshd_config, this will change the SSH-access to the PI-server self.
In our case we extended the vty input to telnet for the few older ssh1 only image devices
Steffen

Similar Messages

  • 3rd party device support

    Hi,
    Is there going to be any change in the way MARS would support 3rd party devices (non-cisco) like checkpoint, Intrushield etc in future?
    Thanks in advance,
    Valsa Raj

    1. Discovery supports many non-CDP modules such as ping sweeps, ARP cache lookups, and routing table lookups.  However, Topology Services still requires CDP to build interconnections between devices.
    2. Yes, non-Cisco devices will show up on the Topology Map with a generic icon.
    3. There is no restriction except it has a maximum of 50 devices.
    4. The Fault component of LMS 4.0 can integrate with HPOV NNM.

  • Use of files dowloaded from i-tunes store on Roku (3rd party device)

    Hello,
    I have a Roku soundbridge system which play my music from my Mac compute r(via wifi). Unfortunaley it does not succeed to play the files bought on i-tunes store as it says they are protected. How can i take out the protection or have it read by my system. On roku site, i only find "apple does not allow streaming of files downloaded from their music store to 3rd party device." Is there any solution for me to listen to the albums i have bought on my system??? thks for your help

    Sorry, but as Roku's web site says, no third-party devices can play tracks purchased from the iTunes Store. Tracks from the iTunes Store can only be played in iTunes or QuickTime Player or on an iPod, Apple TV, iPhone or iTunes-equipped Motorola cell phone.

  • HT204368 Can you (Handoff) control your iphone with 3rd party devices ? (Like making calls, sending message, etc...)

    I am wondering if you can control your iphone or other iOS devices with 3rd party devices? I have in mind like making calls, sending sms, etc....
    Thank you!

    No,

  • ISE iPEP + 3rd party device VPN bridge or route mode

    Dear All,
    I would like to get some advice from the community regarding my idea.
    We would like to integrate ISE iPEP with a 3rd party VPN device using bridge mode.
    However i can only find documents describing the following scenarios,
    - routed mode with VPN device
    - bridge mode with Wireless Controller
    So the questions is that is bridge mode supported if i would like to integrate ISE iPEP with a 3rd party VPN device or is it even possible to achive this kind of deployment?
    Thank you in advance.
    Best Regards,
    Erik Molnar

    Thanks for the reply Marcin.  Both of your suggestions are good ones, however in this scenario both DC firewalls are alive at the same time, so there needs to be some kind of logic on the device at the remote site to say that it should only use tunnel B if tunnel A is down.
    Thinking on this, is it possible to run an 'interface' or 'routed' mode IPSEC VPN with the ASA?  I know this is possible with the Fortigates and think it's the default mode for Junipers.  If that were possible we might be able to have both tunnels up and have OSPF run over them which would be another way to solve this problem.

  • Ethercat 3rd Party Device Profile XML File not complete

    Hi all,
    I'm trying to use a Schneider LXM32 servo drive coupled to a NI cRIO 9074 Ethercat master.
    The problem is that my LabVIEW project is not showing me the full device profile.
    There are 4 available PDO for this device :
    1) Cyclic Synchronous Position
    2) Cyclic Synchronous Velocity
    3) Cyclic Synchronous Torque
    4) Free switching beetween 1) 2) or 3)
    BUT, I only see the firts PDO parameters after importing the xml file. If I open the xml file manually, I see that all the PDO are available.
    The xml file is available in this post.
    Of course, I need to operate in the 4) mode, not the 1)
    Help me, please....
    Sébastien MICHAUD
    CLD
    Attachments:
    Schneider_Electric_LXM32M_V114.zip ‏18 KB

    Hi,
    Thank you for your answer.
    I successfully modified the XML file of my Schneider drive :
    Now I have a lot of others problems (I have made a request on NI France, I supposed you are the one who phoned me today).
    1) The XML file of my LTi DRiVE (another drive of the test bench) is done like this (see attachment):
    1) I can't move the Sm tag because it's already everywhere
    2) I don't understand why 4 devices are exposed.
    Additionnaly, see below the LabVIEW project with this device :
    3) The I/O exposed for the 2 Devices (Schneider and Lti) are shared variables. But I want to poll these I/Os every 125µs. The scan engine can run at 1 ms. So, if a put a "percentage of each scan period" to 1% (the default value is 40%), will I be able to poll every 10 µs ?
    In this example :
    https://decibel.ni.com/content/docs/DOC-11191
    The scan period is 4 ms at the best, so with 40% of each scan period, it represents 1.6 ms.... am I correct ?
    4) Is it necessay to use NI SoftMotion (https://decibel.ni.com/content/docs/DOC-11191) to get/set data to a motor drive ? Is it much more easy with NI SoftMotion ?
    Thanks,
    Sébastien MICHAUD
    Attachments:
    LUST_22_SO.zip ‏2 KB

  • Line in for itunes - Use computer audio in or 3rd party device

    I wanted to know if there were any devices or a way to get something recognized by itunes that you could plug in something like a live band, that would be recognized as a device and then just select that device and it would play the audio from that thru itunes.
    The reason for this is I use apple remote and airport expresses throughout my house to play music. It would be nice to be able to pipe in sound from another source and select it thru apple remote and play that audio thru the airportexpresses.
    For example, someone brings over a record player and we hook it up, plug the RCA outputs into the device or line in on the computer. Then when itunes is opened the device/line in shows up as a source, and I guess to fit into apples schema, there would be one "song" on the device and it would just "play" that which would then send the incoming sound thru itunes and play over the speakers thru airportexpress.
    Im suprised there is no device or option to play "line-in" or maybe there is a way to have the sound line in of the computer be used. Im sure there are lots of applications for this.  I suppose its possible apple doenst want this option but maybe someone out there has some kind of work around to accomplish my goal.
    Thanks
    james
    Maybe it could be something line a live podcast or personal radio station that could be set up. I just thought of this looking at the catagories.

    I eventully figured out how to do this. It cant be done in Itunes. You have to use airfoil not itunes to broadcast to the airtunes speakers. You can select any input or program to supply the sound.  If you want to control this from your iphone you need to install ReeMote and the ReeMote server on your mac to control airfoil Volume, you can not control the input selection from the reemote application.  This must be done on the Mac but it defaults to the previous selected input all the time on startup.

  • Connecting 3rd party devices to my computer

    How do I connect lap tops and i phones to my imac so that they can access app stores etc?

    Like I said before, you can connect 2 iPods to one computer. However, there are multiple options. If you don't care whether some of his songs are on your iPod, and vice versa, you can use the same user on the computer. Now... If you each want your own library, there's two ways you can set this up: #1 - Create a new user on the computer, and install iTunes 7 there. Then, one of you use one user, and the other can use the created one. The songs can be different on in iTunes on either user, it'w a whole new library. #2 - If you don't want to create a new user on the computer, you can set your iPods to "manually update songs" so that iTunes doesn't automatically put all the songs in the library on the iPod. With this method, you have to manually drag songs you want from iTunes to your iPod icon in iTunes. That way, you can selectively put your songs on your ipod and he can put his on his iPod using the same library.
    Hope this helps

  • Bluetooth Audio Control from 3rd party devices

    I just bought 2010 Mazda3, and it has Bluetooth handsfree calling and audio capability. I have paired my iPhone 3G to my car and can stream music from my iPhone to my car stereo via Bluetooth but I cannot control my iPhone through the car's controls. My Mazda has the ability, but Apple needs to update to the newer/advanced Bluetooth profile.
    Attention Apple: Please update to A2DP AVRCP

    BobbyR1984 wrote:
    ...Attention Apple: Please update to A2DP AVRCP
    Welcome to the discussions,
    This is a user to user forum and Apple will not hear you. You can address Apple directly here: http://www.apple.com/feedback/iphone.html

  • ACS autherization for 3rd party device

    Hi all,
    I am trying to set up AAA authentication and autherization for nortel passport through ACS 4.2 server.
    i am sucessful in getting authentication through RADIUS but need to control autherization of nortel passport through ACS.. Can anyone suggest how to do it. I have mentioned few command of nortel...
    Hardware - Nortel passport 7480 / Nortel Multiservice Switch
    7480
    Software - PCR 9.1
    Commands -
    1) d -p vr/* pp/* ipp log/*
    2) ping -ip(10.2.1.14) vr/2 ip icmp
    3) d -p sig/*
    4) d sig/*
    5) d -p vsr/*
    6) d -p vroute/*
    Need help...
    Regards
    Amar

    Hi all,
    I am trying to set up AAA authentication and autherization for nortel passport through ACS 4.2 server.
    i
    am sucessful in getting authentication through RADIUS but need to
    control autherization of nortel passport through ACS.. Can anyone
    suggest how to do it. I have mentioned few command of nortel...
    Hardware - Nortel passport 7480 / Nortel Multiservice Switch
    7480
    Software - PCR 9.1
    Commands -
    1) d -p vr/* pp/* ipp log/*
    2) ping -ip(10.2.1.14) vr/2 ip icmp
    3) d -p sig/*
    4) d sig/*
    5) d -p vsr/*
    6) d -p vroute/*
    Need help...
    Regards
    Amar
    Hi Amar,
    Check out the below link for radious authorization confguration on ACS
    http://www.ciscosystems.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.0/user/guide/c.html#wpxref31687
    Hope to Help !!
    Ganesh.H

  • 3rd party IPS fail open device

    HI all,
    I am looking out for a 3rd party hardware device for IPS 4240 hardware fail open in case if my IPS unit has any hardware problems.
    Please suggest me on different model no/make for any 3rd party devices.
    Thanks
    pratik

    Hi Pratik,
    I am not aware of any.
    However,  Cisco IPS 4260 and IPS 4270-20 support the 4-port GigabitEthernet card (part number IPS-4GE-BP-INT=) with hardware bypass.
    This 4GE bypass interface card supports hardware bypass.
    http://tools.cisco.com/squish/878Dd
    Regards,
    Sid Chandrachud
    Cisco TAC - Security Team

  • 3rd party sip device music on hold not working.

    When creating that COP file, I added the music on hold feature, meaning Music on hold is supported. After the customer installed the COP file into CUCM, created the new device, and configured MOH to play Cisco's sample audio, the MOH does not work. All other features work including Enhanced Message Waiting Indicator, Call Waiting, and Shared Line Appearance.
    When they create a new device in CUCM they follow these steps:
    1. Device > Phones
    2. Add New
    3. Select MH iOS (this is the 3rd party device that has been installed on CUCM via the COP file)
    4. Select Next
    5. Fill out the fields
    6. Select Save and Apply Config
    Please provide the solution or input why it is not working.
    Thanks & Regards,
    Guru

    System Version: 9.0.1.11012-1
    We only hear the Initial and Periodic announcements during the time between the periodic we just get dead air

  • Airplay no longer working with 3rd party after upgrading to Maverick.

    I updated my MacBook Pro this week and I have noticed that the airplay icon is no longer showing up in iTunes to connect to my Denon Amplifier. The interesting thing is that my old iPad 1 that I have that is still running 5.1.1 can connect and play to the receiver just fine.
    Was there an update to the airplay software that would affect 3rd party devices? I was not able to find any new updates for my receiver.

    I woke up this morning with the same problem (all was fine last night).  Only way to get all my mailbox folders back was to use Time Machine while in Mail, choosing the backup file from previous night and selecting EACH MAILBOX to restore (23 for me).  All appears okay so far today (except some of my accessories in the menu bar are gone). 
    I sure hope an update comes SOON.  In anticipation of Mavericks and the new MAIL I switched from Outlook 2011 3 weeks ago transfering 17,000+ files and would hate to back

  • Upgrade to Windows 8.1 Pro Update 1 and it killed all my 3rd party drivers

    Hoping someone can help - my PC upgraded Windows 8.1 Pro (fresh install a few months ago) with the 'Update 1 patch' which was made available a few days ago.  It was done via Windows Update - I let it do its thing for about 15 minutes, restart etc.
    Once the machine restarted, I noticed the following:
    - no network connection
    - no sound
    - no working camera
    I went to the device manager and see a stack of 3rd-party devices with exclamation marks, all stating code 28 (the drivers for this device are not installed).  I go to each device and try to update the drivers - it looks like its going to work and then
    gives the error "The system cannot find the file specified".
    I do some googling and find the setupapi.dev.log.  The log for every device with a problem reads like this:
    >>>  [Device Install (DiShowUpdateDevice) - HDAUDIO\FUNC_01&VEN_10EC&DEV_0900&SUBSYS_1043859D&REV_1000\4&83A6FBB&0&0001]
    >>>  Section start 2014/04/12 01:23:46.588
          cmd: "C:\Windows\system32\mmc.exe" C:\Windows\system32\devmgmt.msc
         dvi: {DIF_UPDATEDRIVER_UI} 01:23:46.608
         dvi:      No class installer for 'Audio Device on High Definition Audio Bus'
         dvi:      Default installer: Enter 01:23:46.647
         dvi:      Default installer: Exit
         dvi: {DIF_UPDATEDRIVER_UI - exit(0xe000020e)} 01:23:46.686
         ndv: {Update Driver Software Wizard for HDAUDIO\FUNC_01&VEN_10EC&DEV_0900&SUBSYS_1043859D&REV_1000\4&83A6FBB&0&0001}
    !!!  ndv:      Driver package import failed for device.
    !!!  ndv:      Error 2: The system cannot find the file specified.
         ndv:      Installing NULL driver.
         dvi:      {Plug and Play Service: Device Install for HDAUDIO\FUNC_01&VEN_10EC&DEV_0900&SUBSYS_1043859D&REV_1000\4&83A6FBB&0&0001}
    !    ndv:           Installing NULL driver!
         dvi:           {DIF_ALLOW_INSTALL} 01:23:48.883
         dvi:                No class installer for 'Audio Device on High Definition Audio Bus'
         dvi:                No CoInstallers found
         dvi:                Default installer: Enter 01:23:48.883
         dvi:                Default installer: Exit
         dvi:           {DIF_ALLOW_INSTALL - exit(0xe000020e)} 01:23:48.884
         dvi:           {DIF_REGISTER_COINSTALLERS} 01:23:48.884
         dvi:                No class installer for 'Audio Device on High Definition Audio Bus'
         dvi:                Default installer: Enter 01:23:48.885
         dvi:                Default installer: Exit
         dvi:           {DIF_REGISTER_COINSTALLERS - exit(0x00000000)} 01:23:48.885
         dvi:           {DIF_INSTALLDEVICE} 01:23:48.885
         dvi:                No class installer for 'Audio Device on High Definition Audio Bus'
         dvi:                No CoInstallers found
         dvi:                Default installer: Enter 01:23:48.886
    !    dvi:                     Installing NULL driver!
         dvi:                     Install Null Driver: Removing device sub-tree. 01:23:48.887
         dvi:                     Install Null Driver: Removing device sub-tree completed. 01:23:48.890
         dvi:                     Install Null Driver: Restarting device. 01:23:48.892
         dvi:                     Install Null Driver: Restarting device completed. 01:23:48.892
         dvi:                     Install Device: Starting device. 01:23:48.892
         dvi:                     Install Device: Starting device completed. 01:23:48.893
         dvi:                Default installer: Exit
         dvi:           {DIF_INSTALLDEVICE - exit(0x00000000)} 01:23:48.894
         ump:      {Plug and Play Service: Device Install exit(00000000)}
         ndv: {Update Driver Software Wizard exit(00000002)}
    <<<  Section end 2014/04/12 01:23:50.286
    <<<  [Exit status: FAILURE(0x00000002)]
     It seems like 'update 1' as crapped all over my driver store.
    What can I do to fix this - I have tried a raft of things such as pnputil commands to add the driver INFs manually (they fail saying 'element not found'), but still I am stuck without sound, network and camera.
    This will be the last time I let Microsoft update automatically install - it will now be 100% manual, and done after a few weeks to ensure there aren't bugs.

    espero y te sirva este link :)
    http://blogs.itpro.es/octaviordz/2014/04/05/actualizar-de-windows-8-1-2012r2-a-windows-8-1-ws2012r2-update-con-script-de-powershell/
    Freelance-IT http://www.freelance-it.com.mx

  • Abort/Exit 3rd party program

    Hi!
    I've developed a test system that flashes a device via a 3rd party flasher (hardware and software).
    Sometimes the 3rd party program freezes or crashes for an unknown reason, can be hardware or software.
    I communicate with the 3rd party program in a separate loop and uses the System Exec.vi to call the 3rd party program via its Command Prompt tool.
    I am pretty sure, without actually having tested, that the rest of my application is responsive and running.
    Question:
    I could implement a timer function that after X milliseconds says "Hey! You havn't completed the flash sequence in the time I gave you, ABORT!'.
    But... is there some way to kill that 3rd party program automatically when a timer indicates a problem? Without the user having to open the Task Manager and end the process manually.
    Or maybe another way to solve the problem.
    Best regards
    Peter

    What is that 3rd party device?
    Funny story:  I was working along side another developer that was having a simillar issue.  Out of the blue the 3rd party flash programmer would just hang up.  This is not desired in high volume automated production test systems.  After a few days of banging on the problem they asked me for ideas.  I immediately whent to the manufactures web-site saw they had a FAQ section and that FAQ#2 was "Is the xxx Device suitable for automated high volume systems?"
    BINGO!  one more mouse click and I found the answer.  "No, this is not an anticipated use case for xxx device.  Every once in a while the device becomes unresponsive requiring a system reboot to restore proper operation."
    This is what I call "Other people funny"  its only funny when it does not happen to you.
    Jeff

Maybe you are looking for