PICL configuration missing for T2000

Hi,
we recently tested removing power from one half of a T2000, but no alarms/errors were reported. The following output can be seen:
# /usr/sbin/prtpicl|grep -i ps
          pseudo (devctl, 8100000820) Compare this to a SUNW,Sun-Fire-880
# /usr/sbin/prtpicl |grep -i ps
              PS0_PR_SENSOR (gpio, 80000001e7)
              PS1_PR_SENSOR (gpio, 800000022a)
              PS2_PR_SENSOR (gpio, 800000026d)
              PS0_SLOT (picl, 800000018d)
                  PS0 (picl, 800000019c)
                      PS0_3_3V_I_SENSOR (digital-sensor, 80000001ab)
                      PS0_5V_I_SENSOR (digital-sensor, 80000001b5)
                      PS0_12V_I_SENSOR (digital-sensor, 80000001bf)
                      PS0_48V_I_SENSOR (digital-sensor, 80000001c9)
                      PS0_SENSOR_VALID_SWITCH (switch, 80000001d3)
                      PS0_FAN_FAIL_SENSOR (switch, 80000001d8)
                      PS0_TEMP_FAIL_SENSOR (switch, 80000001dd)
                      PS0_I_SHARE_FAIL_SENSOR (switch, 80000001e2)
              PS1_SLOT (picl, 8000000192)
                  PS1 (picl, 80000001a1)
                      PS1_3_3V_I_SENSOR (digital-sensor, 80000001ee)
                      PS1_5V_I_SENSOR (digital-sensor, 80000001f8)
                      PS1_12V_I_SENSOR (digital-sensor, 8000000202)
                      PS1_48V_I_SENSOR (digital-sensor, 800000020c)
                      PS1_SENSOR_VALID_SWITCH (switch, 8000000216)
                      PS1_FAN_FAIL_SENSOR (switch, 800000021b)
                      PS1_TEMP_FAIL_SENSOR (switch, 8000000220)
                      PS1_I_SHARE_FAIL_SENSOR (switch, 8000000225)
              PS2_SLOT (picl, 8000000197)
                  PS2 (picl, 80000001a6)
                      PS2_3_3V_I_SENSOR (digital-sensor, 8000000231)
                      PS2_5V_I_SENSOR (digital-sensor, 800000023b)
                      PS2_12V_I_SENSOR (digital-sensor, 8000000245)
                      PS2_48V_I_SENSOR (digital-sensor, 800000024f)
                      PS2_SENSOR_VALID_SWITCH (switch, 8000000259)
                      PS2_FAN_FAIL_SENSOR (switch, 800000025e)
                      PS2_TEMP_FAIL_SENSOR (switch, 8000000263)
                      PS2_I_SHARE_FAIL_SENSOR (switch, 8000000268)
          pseudo (devctl, 8000001ff3) Looking at the PICL installation for the two types of machines, there are obvious differences:
# ls /usr/platform/SUNW,Sun-Fire-T200/lib/picl/plugins
libpiclsbl.so
libpiclsbl.so.1
# ls /usr/platform/SUNW,Sun-Fire-880/lib/picl/plugins/
libpiclfrutree.so
libpsvcplugin_psr.so.1
picldevtree.conf
libpiclfrutree.so.1
libpsvcplugin.so
piclfrutree.conf
libpsvcplugin_psr.so
libpsvcplugin.so.1 Are there configuration files missing for T2000 machines? Where can I get them? Or is there something else wrong?
Regards,
Kevin

When the OS was installed to the new system, which Cluster was selected ?
I seem to recall that with the V880's you needed at least Developer
to get all the necessary PICL functions, End-User was not sufficient.
Perhaps there is some difference between your two systems.

Similar Messages

  • ISG Debug - IP configuration missing for radius proxy session initiation

    Folks,
    We are trying to configure the ISG as a Radius-Proxy for EAP Authentication. I have configured aaa server radius proxy, clients and aaa auth radius-proxy group as per the guide. I have my interface config as follows:
    interface TenGigabitEthernet0/2/0.205
    encapsulation dot1Q 205
    ip vrf forwarding CS
    ip address 10.20.0.1 255.255.224.0
    ip helper-address global 172.X.X.X
    no ip redirects
    no ip proxy-arp
    ip tcp adjust-mss 1420
    service-policy type control DEFAULT_RULES
    ip subscriber l2-connected
      initiator dhcp
      initiator radius-proxy
      arp ignore local
    When I try to connect a wifi client to an AP, I can see that the AP is forwarding the Access-Request to the ISG but the ISG does not forward it to the AAA. In the ISG debug I see the following message:
    RADIUS: IP configuration missing for radius proxy session initiation
    Can any one help to identify what is missing here pls?
    Thank You in advance!

    Kiran,
    Did you follow this guide? It looks like the interface configuration is there but you didnt include the actual radius configuration does it follow the guide here -
    http://www.cisco.com/en/US/docs/ios/isg/configuration/guide/isg_radius_proxy.html#wp1055053
    Thanks,
    Tarik Admani

  • Link missing for appraisal documents in MSS Status overview

    Hi all,
    For ESS Status overview page of Flexible Appraisal document, the appraisal documents are listed with links. when we click the link, its taking to the appraisal document.
    For MSS Status overview page of Flexible Appraisal documents, the appraisal documents are shown as texts and there is no link. (hyperlink). Opening the document is possible only by clicking 'Display' or 'Edit' button.
    I have checked throughout the SDN and unable to find the problem. Our functional team says that the link was appearing before. Could some one help on what configuration is necessary to get the link for appraisal documents in MSS
    Thanks,
    Kothand

    Hi Deepak,
    I think i have not made the details clear. Its not the tag or the text values i am talking about.
    Its the POWL page where i am not able to view the link for appraisal documents .
    Below is our MSS landing page for appraisal document
    [MSS Landing page  - |http://www.freeimagehosting.net/8ad47]
    Below is our ESS landing page for appraisal document
    [ESS Landing page -|http://www.freeimagehosting.net/f3572]
    The hyperlink property is missing in MSS page. I beleive its some IMG configuration or portal configuration missing for MSS.
    Can someone Please throw some light on this
    Regards,
    Kothand

  • The boot configuration data for your Pc is missing or contains errors: error code 0x000014c

    Hello, 
    See if any body may help here... I get this blue screen:
    RECOVERY
    Your PC needs to be repaired: 
    The Boot Configuration Data for your PC is missing or contains errors.
    file:\\EFI\Microsoft\Boot\BCD
    Error code: 0xc000014c
    You'll need to use the recovery tools on your installation media. If you don't have any installation media (like a a disc or USB device), contact your system administrator or PC manufacturer.
    Press Esc for UEFI Firmware Settings
    First I was able to get into the option 11 and run the whole factory reset, i was so happy because I tought it will be easy.. but then after I did the factory reset.. I keep getting this blue screen. if I press ESC I get into this next screen:
    F1 System Information
    F2 System Diagnostics
    F9 Boot Device Options
    F10 BIOS Setup
    F11 System Recovery
    ENTER - Continue Startup.
    this is what happen when I click any of this options:
    F1 I get into the System Information with no problems, then I click <ESC> to continue and get back to the last screen... then I press F2 and super, I am able to run Memory Test and Hard Drive Check 100% with no problems in any of those, after I am done with my teste I press exit and I am back to the F1,F2, ETC menu... now I want to try F9, F10 or F11. bummer.. in this 3 options I get back to the blue screen described at the beggining of this post. (I already connect a USB with an boot loader, which works perfectly) 
    so I can't do anything, nothing at all!! crazzines. 
    So what I did to check why I can't get into the BIOS or at least to boot from my USB... I removed the botton cover of my laptop and removed the hard drive and that's how then I was or I am able to Log into the BIOS, - I did the changes to boot first from the USB and then from the HD and this is how I was able to boot from the USB - BUT If I connect back the Hard drive, I am not able to get into the BIOS or boot from the USB - so basically I am stuck in this blue screen and I can't boot from a USB if I have the HD connected.. I can't use any option.. no BIOS, nothing.. only if again, i disconnect the HD.  
    This is an:
    HP ENVY TS Sleekbook 4
    PRODUCT NUMBER  D1A99UA#ABA
    SYSTEM BOARD ID: 1894
    Bios F.25 
    **** I though that by updating the BIOS I may be able to get help, nothing. What I did is, I removed the HD and then and boot from the USB and with a DOS command propmt I excecuted the Bios Update from F.21 to f.25... but again, when I installed the hard drive back, BUMMER, nothing I can't do nothing but this silly blue screen. 
    Any idea of what should I do? 
    Thanks in advance.
    This question was solved.
    View Solution.

    If you can't access BIOS with the hard disk connected, you certainly won't be able to boot to the usb recovery flashdrive. That is indicative of a failed hard disk.
    Install a new hard disk and then boot to the recovery flashdrive.
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Missing configuration entry for data - index relationship

    IN ST04 -> configuration -> Data Class
    all data classes are in yellow I'm trying to activate them and getting the following error
    "Missing configuration entry for data - index relationship"
    This is the result of  a system copy
    Thanks
    Kkhaldoun

    Hi All,
    Just an update, I was able to get around my problems by patching the 2004s media from sp6 to sp8, uninstalling my scs, and database and re-installing from the patched media.

  • I am facing error while running Quickpay in Fusion payroll that "The input value Periodicity is missing for element type KGOC_Unpaid_Absence_Amount. Enter a valid input value". Any idea?

    I am facing error while running Quickpay in Fusion payroll that "The input value Periodicity is missing for element type KGOC_Unpaid_Absence_Amount. Enter a valid input value". Any idea?

    This is most probably because the Periodicity input value has been configured as "Required" and no value has been input for it.
    Please enter a value and try to re-run Quick Pay.

  • 'schema is missing for the component ' while creating a web service

    Hello,
    I am trying to create a web service in Application Explorer on my dev server as described in:
    http://download-east.oracle.com/docs/cd/B31017_01/integrate.1013/b28996/config.htm#BABBJHHF
    I use an adapter for JDE Edwards EnterpriseOne. After supplying the parameters (service, license, method name) I get: com.ibi.bse.AddWSWorker:java.lang.Exception: schema is missing for the component.
    I think the environment (JDE system, GenJava files) is configured correctly as I am able to communicate using J2CA.
    Debug mode produces ibse_log.txt with some errors (below) but this does not give me a clue to the solution. Could you point me in the right direction?
    20070507-16:54:04 DEBUG com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:adapter factory method: [GETCOMPONENT]
    20070507-16:54:04 DEBUG com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:iwae method: [GETCOMPONENT] with idx [4]
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.edaqm.XDClassLoader:com/jdedwards/application/interop/jdejava_cfin/D0100033.class found as url jar:file:///C:\oracle\product\10.1.2\as_1\adapters\application\lib\JDEJAVA_CFINInterop.jar!/com/jdedwards/application/interop/jdejava_cfin/D0100033.class
    20070507-16:54:05 ERROR com.iwaysoftware.ibse.iwse.SimpleConfig:Error, properties generation
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:output:<?xml version="1.0" encoding="UTF-8" ?>
    <SOAP-ENV:Envelope xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
    <SOAP-ENV:Body>
    <GETCOMPONENTResponse xmlns="urn:schemas-iwaysoftware-com:dec2002:iwse:af">
    <sid>2FDCA46F4D0D87AEBB2EF26FDF3949B4</sid>
    </GETCOMPONENTResponse>
    </SOAP-ENV:Body>
    </SOAP-ENV:Envelope>
    20070507-16:54:05 INFO com.iwaysoftware.ibse.iwse.IBSEServlet:Received connection from host [10.1.1.27] with ip [10.1.1.27] and user [null]
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:Enter: doPost()...
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:request pathInfo [XDSOAPAdapterFactory]
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:request query [null]
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:soap action is []
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:<?xml version="1.0" encoding="UTF-8" ?>
    <SOAP-ENV:Envelope SOAP-ENV:encodingStyle="http://schemas.xmlsoap.org/soap/encoding" xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/">
    <SOAP-ENV:Header>
    <ibsinfo xmlns="urn:schemas-iwaysoftware-com:dec2002:iwse:af">
    <service>iwae</service>
    <method>GETSCHEMA</method>
    <license>admin</license>
    <disposition/>
    <Username>ibseadmin</Username>
    <Password>1234512340023212232</Password>
    </ibsinfo>
    </SOAP-ENV:Header>
    <SOAP-ENV:Body>
    <GETSCHEMA xmlns="urn:schemas-iwaysoftware-com:dec2002:iwse:af">
    <sid>2FDCA46F4D0D87AEBB2EF26FDF3949B4</sid>
    <component location="services/JDEJAVA_CFIN/B0100033/GetEffectiveAddress" name="GetEffectiveAddress"/>
    </GETSCHEMA>
    </SOAP-ENV:Body>
    <SOAPAction agentName="XDSOAPAdapterFactory" cid="1D90AB1A134EFDA81C656CA404EEC38D"></SOAPAction>
    </SOAP-ENV:Envelope>
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:adapter factory method: [GETSCHEMA]
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:iwae method: [GETSCHEMA] with idx [17]
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.edaqm.XDClassLoader:com/jdedwards/application/interop/jdejava_cfin/D0100033.class found as url jar:file:///C:\oracle\product\10.1.2\as_1\adapters\application\lib\JDEJAVA_CFINInterop.jar!/com/jdedwards/application/interop/jdejava_cfin/D0100033.class
    20070507-16:54:05 ERROR com.iwaysoftware.ibse.iwse.SimpleConfig:Error, schema generation
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.edaqm.XDClassLoader:com/jdedwards/application/interop/jdejava_cfin/D0100033.class found as url jar:file:///C:\oracle\product\10.1.2\as_1\adapters\application\lib\JDEJAVA_CFINInterop.jar!/com/jdedwards/application/interop/jdejava_cfin/D0100033.class
    20070507-16:54:05 ERROR com.iwaysoftware.ibse.iwse.SimpleConfig:Error, schema generation
    20070507-16:54:05 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:output:<?xml version="1.0" encoding="UTF-8" ?>
    <SOAP-ENV:Envelope xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
    <SOAP-ENV:Body>
    <GETSCHEMAResponse xmlns="urn:schemas-iwaysoftware-com:dec2002:iwse:af"/>
    </SOAP-ENV:Body>
    </SOAP-ENV:Envelope>
    20070507-16:54:19 INFO com.iwaysoftware.ibse.iwse.IBSEServlet:Received connection from host [10.1.1.27] with ip [10.1.1.27] and user [null]
    20070507-16:54:19 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:Enter: doPost()...
    20070507-16:54:19 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:request pathInfo [XDSOAPAdapterFactory]
    20070507-16:54:19 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:request query [null]
    20070507-16:54:19 DEBUG com.iwaysoftware.ibse.iwse.IBSEServlet:soap action is []
    20070507-16:54:19 DEBUG com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:<?xml version="1.0" encoding="UTF-8" ?>
    <SOAP-ENV:Envelope SOAP-ENV:encodingStyle="http://schemas.xmlsoap.org/soap/encoding" xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/">
    <SOAP-ENV:Header>
    <ibsinfo xmlns="urn:schemas-iwaysoftware-com:dec2002:iwse:af">
    <service>iwae</service>
    <method>ADDWS</method>
    <license>admin</license>
    <disposition/>
    <Username>ibseadmin</Username>
    <Password>1234512340023212232</Password>
    </ibsinfo>
    </SOAP-ENV:Header>
    <SOAP-ENV:Body>
    <ADDWS xmlns="urn:schemas-iwaysoftware-com:dec2002:iwse:af">
    <sid>2FDCA46F4D0D87AEBB2EF26FDF3949B4</sid>
    <component location="services/JDEJAVA_CFIN/B0100033/GetEffectiveAddress" name="GetEffectiveAddress"/>
    <svcname>test6</svcname>
    <svcdesc>test6</svcdesc>
    <licname>test</licname>
    <mthname>GetEffectiveAddress</mthname>
    <mthdesc>test6</mthdesc>
    </ADDWS>
    </SOAP-ENV:Body>
    <SOAPAction agentName="XDSOAPAdapterFactory" cid="FC73705AC1A76B30A602E68CCD627EC2"></SOAPAction>
    </SOAP-ENV:Envelope>
    20070507-16:54:19 DEBUG com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:adapter factory method: [ADDWS]
    20070507-16:54:19 DEBUG com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:iwae method: [ADDWS] with idx [9]
    20070507-16:54:19 DEBUG com.iwaysoftware.ibse.edaqm.XDClassLoader:com/jdedwards/application/interop/jdejava_cfin/D0100033.class found as url jar:file:///C:\oracle\product\10.1.2\as_1\adapters\application\lib\JDEJAVA_CFINInterop.jar!/com/jdedwards/application/interop/jdejava_cfin/D0100033.class
    20070507-16:54:19 ERROR com.iwaysoftware.ibse.iwse.SimpleConfig:Error, schema generation
    20070507-16:54:19 ERROR com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory:XD[FAIL] cause: 0 subcause: 0 message: schema is missing for the component
         at com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory.buildSchemaInfo(XDSOAPAdapterFactory.java:1556)
         at com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory.addMethod(XDSOAPAdapterFactory.java:1628)
         at com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory.addService(XDSOAPAdapterFactory.java:1492)
         at com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory.handleADDWS(XDSOAPAdapterFactory.java:1376)
         at com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory.processWithDB(XDSOAPAdapterFactory.java:1858)
         at com.iwaysoftware.ibse.iwse.XDSOAPAdapterFactory.process(XDSOAPAdapterFactory.java:186)
         at com.iwaysoftware.ibse.iwse.IBSEServlet.doPost(IBSEServlet.java:550)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
         at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:824)
         at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:330)
         at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:830)
         at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:224)
         at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:133)
         at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:192)
         at java.lang.Thread.run(Thread.java:534)
    pawel

    There is a note 1818432 for this issue.

  • Error : Tax statement item missing for tax code

    Hello Gurus,
    I have issue while releasing a billing document to accounting from VF02. The error says 'Tax statement item missing for tax code AA'
    Any idea??
    Prase

    Dear Prasanth,
    Please review note 112609 and 400766 carefully, which explain the
    tax rules.
    The FF805 error is most likely triggered due to configuration in
    the pricing procedure.
    If an active tax condition record is found (for example on UTXJ), even
    though it is statistical, the tax code (linked to the record) is then
    distributed to the active price conditions for that item pricing.
    When it passes to FI, the active tax condition is passed but not
    the price because an active price condition cannot be found.
    In the SD-FI interface, for every price condition sent over,
    there MUST be a tax condition sent over, hence the FF805.
    I think may be what is happening in your case.
    If after setting reference steps in your procedure according to the
    guidelines in 112609, you still encounter the FF805, please let me know.
    Hope this is helpful. Thank you.

  • Tax statement item missing for tax code A0

    I got intercompany billing that has not been released to accounting, when I tried to release to accounting got this error message :
    Field Profit Ctr is a required field for G/L account 6000 14112100
    Message no. F5808
    Diagnosis
    The value for field "Profit Ctr" in the interface to Financial Accounting is an initial value but you are required to make an entry in the field selection for G/L account "14112100" in company code "6000" linked to the field selection for posting key "50".
    System response
    Error
    Procedure
    It might be an error in the configuration of the G/L account field selection. The initial application, used to call up the interface must otherwise define a value for field "Profit Ctr". If this is the case, contact the consultant responsible for the application used to call up the interface or get in contact with SAP directly.
    when I looked at it because IV01 in billing document is empty and PI01 in sales document is empty, when I tried to add the value IV01 in intercompany billing manually and tried to release again got this error message:
    Tax statement item missing for tax code A0
    Message no. FF805
    Diagnosis
    No tax item exists for tax code A0 in a G/L account item. A possible cause is an incorrect transfer of parameters by the application to the Accounting interface.
    Procedure
    Enter an OSS message.
    Can someone help please? I can't correct the SO and DO because it's in the past already can't be reversed.
    regards,
    Dwi

    Hi,
    Please check the following note
    Note 971253 - Causes for error message FF805 in SD
    I hope it will help you.
    Regards,
    Jigar

  • Tax statement item missing for tax code O0

    Hi all,
    i am getting an error message while releasing SD billing documents to Accounting. the complete error message is
    NA FF805
    Text:
    Tax statement item missing for tax code O0
    Diagnosis:
    No tax item exists for tax code O0 in a G/L account item. A possible cause is an incorrect transfer of parameters by the application to the Accounting interface.
    Procedure:
    Enter an OSS message.
    It would be great help if some one reply back with what should i do..
    We are on R/3 4.7 enterprise
    Thanks in Advance
    Sivaram

    HI Sivaram,
    Please review note 112609 and 400766 carefully, which explain the tax rules.
    The FF805 error is most likely triggered due to configuration in the pricing  procedure.
    If an active tax condition record is found (for example on UTXJ), even though it is statistical, the tax code (linked to the record) is then distributed to the active price conditions for that item pricing.
    When it passes to FI, the active tax condition is passed but not the price because an active price condition cannot be found. In the SD-FI interface, for every price condition sent over, there MUST be a tax condition sent over, hence the FF805.
    I think this may be what is happening in your case.
    Normally it would not be advised to bypass the check in FI_TAX_SV_BSEG_BSET_GROSS - please note that when passing from SD to FI:
    -> There must be at least a revenue line for each tax line.
    -> For each revenue line containing a certain tax indicator there must be a tax line with this indicator.
    -> If a tax condition has base value = 0  OR is inactivated OR is statistical => then it is not passed to FI.
    I hope this information will help you to solve your issue. If it resolves your issue, kindly confirm this message at your earliest convenience. Otherwise, please give me feedback for further analysis.
    Please assign points if it useful.
    Regards
    Ravinagh Boni

  • Tax statement item missing for tax code O0 .     ||Message no. FF805

    Hi Gurus,
    I am trying to post SD billing document to accounting. The system issues error message FF 805 - Tax statement item missing for tax code O0. Our Development and Production systems are working fine and we have this issue with the quality system.
    The following TCODES are verified for the configuration in FI  and SD.
    FTXP, FS00, V/0K, V/08, VK13, MEK3, FB13, VK0A
    We have gone through the checklist specified in the following threads.
    Error : Tax statement item missing for tax code
    FF805 Tax statement item missing for tax code
    FF805 Tax statement item missing for tax code O0
    Tax code error
    Eror message FF805 when mwst based condition value is zero
    As well as refered the following OSS notes and checked the configuration with the development/production systems, which seems to be exactly same.
    Note 971253 - Causes for error message FF805 in SD
    Note 112609 - How are tax codes transferred to conditions ?
    Note 400766 - Changes in accounting interface for Release 4.6
    Please let us know if we are missing anythig else.
    Thanks,
    Veeru.

    Issue resolved, Ultimately there was some user-exit missing.
    Thanks,
    Veeru.

  • FF805 Error tax statement item missing for tax code

    I am getting the above error when am trying to release an invoice to accounting in VF02. We are using a pricing procedure that contains US tax conditions and Europe tax conditions and the European condition has got determined according to the access sequence and condition records maintained. The tax code shows up correctly in the sales order and the billing document. The FTXP configuration is also in place. Does anyone have any idea about how to fix this. Any guidance or help on this greatly appreciated.
    Thanks
    Bharathi

    Hello Bharathi,
    If the problem happens in the invoice relevant for US, please notice:
    For 'US' the tax jurisdiction functionality is activated and as a result
    the FI tax side has special requirements for SD invoices that will be
    posted to FI.
    Please check if the used pricing procedure is customized as a tax
    jurisdiction procedure (compare the standard RVAAUS).
    At least one tax condition has to be transferred with condition
    type (KNTYP) = '1'. That is a prerequisite for the filling of the
    deepest tax level (BSET-TXJDP) for the tax jurisdiction functionality.
    That is missing for the invoice and as the deepest level for the
    tax jurisdiction is missing, the error FF 805 will be issued.
    Please also refer to the SAP notes which might be helpful:
    other attached notes which should guide you:
    441456     Tax Shipments between the US and Canada using juris
    419124     Export billing document with tax jurisdictions
    380158     Jurisdiction code for export business transaction
    In the vast majority of cases, error FF805 occurs because of an error
    in your pricing procedure. The previously attached note 112609 explains
    in detail how tax codes are transfered to conditions.
    The note 400766 explains the checks performed by the system on the Tax
    codes:
    1. system checks whether there is a revenue line for each tax line.
    2. in the reverse case, for each revenue line containing a certain
       tax indicator there must be a tax line with this indicator.
    If the tax condition has condition value zero and condition base
    value zero, then it is not transferred to FI.
    If you have revenue lines containing a tax indicator XX, but no
    tax line with tax indicator XX, then the error FF805 issues, and
    it is justified. => Please check these informations. I have attached
    notes for further information.
    -> EXAMPLE
       If tax condition MWST has base amount zero and value zero; for this
       reason it is not passed to accounting. But, according to the
       criteria reported by note 112609, its tax indicator EG: A7
       has been assigned to the condition EG: ZBR1.
       So in accounting there would be a revenue line with tax indicator A7,
       but there isn't any tax line with indicator A7 (because MWST doesn't
       pass to FI). The note 400766 states situation is unallowed, and error
       FF805 is justified.
    Please review this information as hope it will help solve your issue.
    Best regards,
    Alex

  • Error: FF805 Tax statement item missing for tax code

    Hi all,
    We are getting an error when releasing billing document to accounting in 4.7system.
    Error: FF805 Tax statement item missing for tax code O0
    No tax item exists for tax code O0 in a G/L account item. A possible cause is an incorrect transfer of
    parameters by the application to the Accounting interface.
    Please give your inputs and will be rewared.
    Quick reponse will be appreciated.
    Thanks & Regards.

    Dear Mehak,
    I am sorry for the late reply, but I started (in fact) to work in SDN Forum this year, even I entered earlier.
    We have many FF805 errors reported by customers and the same solution has resolved the problem. Please note that the SD-FI interface changed from earlier releases. The note 400766 eplxains the checks made.
    So it is possible that now you get error message FF805, when in an earlier release you didn't get it, eventhough no customizing change.
    Please review note -> 392696   R/3 Tax Interface Configuration Guide
    However please note => In the vast majority of cases, error FF805 occurs because of an error in your pricing procedure. The attached note 112609 explains in detail how tax codes are transfered to conditions.
    The note 400766 explains the checks performed by the system on the Tax codes:
    1. system checks whether there is a revenue line for each tax line.
    2. in the reverse case, for each revenue line containing a certain tax indicator there must be a tax line with this indicator.
    If the tax condition has condition value zero and condition base value zero, then it is not transferred to FI.
    If you have revenue lines containing a tax indicator XX, but no tax line with tax indicator XX, then the error FF805 issues, and it is justified. => Please check these informations.
    -> EXAMPLE
       If tax condition MWST has base amount zero and value zero; for this reason it is not passed to accounting. But, according to the criteria reported by note 112609, its tax indicator EG: A7
       has been assigned to the condition EG: ZBR1.
       So in accounting there would be a revenue line with tax indicator A7, but there isn't any tax line with indicator A7 (because MWST doesn't pass to FI). The note 400766 states situation is unallowed, and error FF805 is justified.
    IMPORTANT: Just a hint, any issue with FI, kindly report in the forum:
    Expert Forums - SAP Solutions - ERP Financials
    There you will find a lot of people that works with FI and can help you with future issues, including me
    I hope I could help you
    Kind Regards,
    Vanessa Barth.

  • How to solve this "Prefix number: entry missing for system EC5 client 800"

    Hi,
       I am workflow learner, I am having theoretical knowledge on it.
    Now, I started to practice practically in my IDES server.
    I am getting an error message while I am trying to save my standard task with my object type and method and event (which were already created in SWO1).
      My error message details.....
    Prefix number: entry missing for system EC5 client 800
    Message no. 5W023
    Diagnosis
    Tasks, rules, and workflow definitions require an ID that is unique throughout all systems and clients. In this way, you can ensure that you can transport these objects from one system into another at any time (without restrictions). From a technical point of view, the uniqueness of the ID is ensured by what is known as a "prefix number". You can define a separate prefix number for every system and every client in table T78NR.
    System response
    If a prefix number is not defined in the client in which you are currently working, it is not possible to maintain (maintenance terminates).
    Even I tried to create on entry in the table T78NR, but as that is standard table, I am unable to make an entry.
    Hope we have to configure the workflow, I am not having any Basis consultant with me. Can anyone help to cross this problem.
    Thanks and Regards,
    Surender Batlanki.
    Edited by: Surender Batlanki on Oct 15, 2008 2:20 PM

    HI Surender and  Other SAP Work flow gurus
    Surender, u said, that you got the solution.
    As honestly speaking i am new to SAP Workflow. Can u please please guide me the instruction and document if any. I am practising in Test Server machine. I will be really happy that if u all GEMS helps me to get out of it.
    in Prefix number OOW4, system is asking me to enter, the Prefix number, Interval start, Interval End, and Check Sum.
    I entere the same 980 in prefix number, and i dont know what to enter the Interval start and interval end and check sum.
    Also there is some msg coming when i tried to manage some values, " NO Intervals can be reserved for this prefix number" - MSg No: 5W179.
    Please gurus help me.
    Regard
    Guru

  • Configure SSO for ITS to R/3 using SNC/Kerberos

    Our R/3 systems had been configured for SSO using SNC and Kerberos for awhile now.  We now have a requirement to configure SSO between ITS and R/3.  Since our R/3 env. has been using kerberos library, we won't be able to use SAP Cryptographic library.  I had modified the registry, environment and services in itsadmin to point to the kerberos library and principal names for agate and r/3 servers as described in SNC User Guide; also, I updated table SNCSYSACL with the Agate SNC name.  That seems to work fine.  From the trace file, it recognized GSS-API library for Kerberos and the SNC name for Agate.  However, when I tried to logon to R/3 from ITS, I still am being prompted with the logon screen to enter my SAP account/password.
    I found several whitepapers and documentations stating that ITS does support Kerberos for SSO but I couldn't find any procedure on how to implement it.  Following is the error I'm getting from the sapbasis.trc file but I can't find any document on this error:
    =====================================================
    [Thr 5284] SncInit(): Initializing Secure Network Communication (SNC)
    [Thr 5284]       PC with Windows NT (mt,ascii,SAP_UC/size_t/void* = 8/32/32)
    [Thr 5284] SncInit(): Trying environment variable SNC_LIB as a
          gssapi library name: "C:\WINNT\system32\gsskrb5.dll".
    [Thr 5284]   File "C:\WINNT\system32\gsskrb5.dll" dynamically loaded as GSS-API v2 library.
    [Thr 5284]   The internal Adapter for the loaded GSS-API mechanism identifies as:
      Internal SNC-Adapter (Rev 1.0) to Kerberos 5/GSS-API v2
    [Thr 2888] Sun Jan 15 22:44:59 2006
    [Thr 2888] <<- ERROR: SncSetParam()==SNCERR_PARAM_DENIED
    [Thr 2888] *** WARNING => NO Domain! domain==NULL means: No domain at all within the cookie. [sapss1_loctr 333]
    [Thr 2888] Sun Jan 15 22:45:29 2006
    [Thr 2888] *** WARNING => NO Domain! domain==NULL means: No domain at all within the cookie. [sapss1_loctr 333]
    =====================================================
    Does anyone know what am I missing?  Any help is greatly appreciated.
    Thank you!
    Diem

    Hi Markus,
    I also just installed/configured PAS for LDAP authentication using the "PAS for External Authentication Mechanisms" documentation.  I think the domain problem probably due to not having the external authentication mechanism install (in this case - PAS).  Does that sound right to you?
    I tried both options for ~extid_type parameter = "LD" and "UN".  I added the DN information to table USREXTID when ~extid_type="LD" but both options gave me error of "LDAP authentication failed".  I increased the trace level for sapextaut.trc but I don't see enough detail information.  Following are the errors/data from the trace file.  Can you please let me know how I can tell what string is being passed for authentication? 
    I'm quite sure the LDAP host and port data is correct since we've been using the same information for the SAP LDAP connector and we've been using our LDAP connector between MS AD and R/3 for a long time without any problem. 
    To logon to R/3 through ITS, I entered the AD account (CN attribute in AD) when I got the errors.
    Thank you very much for all your help.
    Diem Tran
    Trace:
    =====================================================
    2006-01-18T01:39:30.734 p001688 t4992 s0158B4E8 [sapextauth,  437]: W sapextauth: PAS session begins...
    2006-01-18T01:39:30.734 p001688 t4992 s0158B4E8 [sapextauth,  456]:     sapextauth: SncNameR3 is:    "p:na1adm/[email protected]"
    2006-01-18T01:39:30.734 p001688 t4992 s0158B4E8 [sapextauth,  462]:     sapextauth: SncNameAGate is: "p:[email protected]"
    2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth,  468]:     sapextauth: SNC_LIB is:      "C:\WINNT\system32\gsskrb5.dll"
    2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth,  568]:     sapextauth: XGatConnectSession leaving....
    2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth,  616]:     sapextauth: XGatHandleLogin called....
    2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth,  976]:     sapextauth: Entering XGatHandleLogin with LDAP...
    2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth,  993]: W Either ~login or ~password missing, returning XGDKRCloginrequired.
    2006-01-18T01:39:50.281 p001688 t4992 s00000000 [sapextauth,  398]:     sapextauth: XGatEventOpenSession called...
    2006-01-18T01:39:50.281 p001688 t4992 s0158B4E8 [sapextauth,  616]:     sapextauth: XGatHandleLogin called....
    2006-01-18T01:39:50.281 p001688 t4992 s0158B4E8 [sapextauth,  976]:     sapextauth: Entering XGatHandleLogin with LDAP...
    2006-01-18T01:39:50.296 p001688 t4992 s0158B4E8 [sapextauth, 1059]:     sapextauth: LDAP port ist 389
    2006-01-18T01:39:50.296 p001688 t4992 s0158B4E8 [sapextauth, 1261]: E sapextauth: LDAP authentication failed.
    2006-01-18T01:39:50.296 p001688 t4992 s0158B4E8 [sapextauth, 1277]: E sapextauth: Wrong try for user Tran_Diem
    2006-01-18T01:39:59.140 p001688 t4992 s00000000 [sapextauth,  398]:     sapextauth: XGatEventOpenSession called...
    2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth,  616]:     sapextauth: XGatHandleLogin called....
    2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth,  976]:     sapextauth: Entering XGatHandleLogin with LDAP...
    2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth, 1059]:     sapextauth: LDAP port ist 389
    2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth, 1261]: E sapextauth: LDAP authentication failed.
    2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth, 1277]: E sapextauth: Wrong try for user Tran_Diem
    =======================================================

Maybe you are looking for

  • Submit + destination

    hi All, I have a Z Function Module(RFC enabled) which passes the Program name its variant and the Destination. Inside this FM it call the JOB_OPEN Submit and JOB_CLOSE FM to trigger the report of different system. i mean if i m in sytem ABC and i wan

  • Description for Variable in variable screen

    Hi Forum, I am using variables type "Replacement Path" in a query for 0FISCYEAR and 0FISCPER3 through by another variable for 0FISCPER. The variables are functioning well, but in the screen of entrance of variables, the variable for 0FISCPER display

  • Microsoft Remote Desktop Preview for WP 8.1 - only for English OS?

    Hi I tried to install the Remote Desktop Preview for Windows Phone 8.1 on my Lumia 930 but got error 80073cf0. Can the preview only be installed on en-US localized devices? Regards Markus

  • A bapi problem of create sales order

    hello,experts, when I want to try the function of bapi 'BAPI_SALESORDER_CREATEFROMDAT1', the return message is the following, 'Material 4070111 is not defined for sales org.4050,  distr.chan.01,  language ZH',actually,the sales org.4050 is defined fo

  • I have a problem with my messages!

    I have the iPhone 5s and my messages take a while to send, when they do send they are being recieved multiple times and when I get messages I get them multiple times. How do I stop this?