Picture gallery for installing the MaxUpgrades P/N SZ-MP2009OPT06

Thought I'd post a few pics for the installation.
Note that the long red SATA data cable runs from the PCIe card's SATA data connector over to the Optical drive bay and connects to the Optical drive's SATA data port. It can be routed behind the Optical drive bay's backplate (as shown) or thru a small opening at bottom left corner (looking at it from the inside) of the plastic bracket that houses the sliding metal flaps that open for the Optical drive's tray. A small screw on left of bracket may have to be loosened some to get the cable end thru the gap.
Note how the assembly will ultimately sit inside the Optical drive bay and position cables to make them tidy before sliding the assembly into the bay.
The two SATA disks will show up in System Profiler and Disk Utility as being in "upper 1" and "Upper 2".
I RAID-0 (software striped using Disk Utility) the two 1.5 TB disk and ran 4 simultaneous mkfile processes in Terminal.app and used Activity Monitor to observe the i/o rate. With 4 mkfile processes running the i/o rate topped out at around 205 MBytes/sec. I launched a 5th mkfile but the i/o rate did not increase beyond the approx 210 MBytes/sec. I assume the 210 MBytes/sec was maxing out the 3Gb/s specs for the disks.
I then ran a Disk Utility single erase of writing zero to the RAID-0 set. This took close to 24 hrs to complete without any errors.
I hope the picture gallery help others with their installation.
Picture gallery at http://gallery.me.com/barrysharp#100326

It can be routed behind the Optical drive bay's backplate
So when you take off the back plate, the cable drops down and swings over to the card, or does it then have to go over or behind the power supply. I loosened and took out that little screw in the front and it was still unusually difficult to thread the cable, really the connector, through it. I was able to get one through but it seemed impossible to put another through.
And all the power you needed came from within the optical bay, right? Do you know of another place where one can get power from?

Similar Messages

Is there a package for installing the FlexNet service only?

Hi,
we are trying to virtualize Acrobat Pro 9 using Softgrid/App-V. Unfortunately the FlexNet service does not support virtualization. According to the virtualization community a possible workaround would be a local installation of the FlexNet service on our terminal servers.
To do that I need an installation package for the FlexNet service only or command line parameters for installing the service from the normal package without installing acrobat.
Is such a package or command available somewhere?
Thanks!

There is no standard iView for ME53N, but you can create you own iView which will point to any SAP Transaction in either WinGui or WebGui Mode and assign it to end users.
Refer to the following standard SAP help:
[http://help.sap.com/saphelp_nw04/helpdata/en/88/266a3e54a2e946e10000000a114084/frameset.htm]
Regards,
Trikanth Basetty

Please prepare asap an extension for installing the new Jquery Mobile 1.2.0 release, which is now th

Please prepare asap an extension for installing the new Jquery Mobile 1.2.0 release, which is now the latest stable version, please. Many thanks, Adolf

Krrish,
So do you mean that the BPEL respository was already there when you did the install? If yes, then that explains the mismatch error. You should always clean up the old references if doing a reinstall. Drop the user and schemas related to PM and do a reinstall.
--Shiv

Patches required for installing the configuration management workbench?

Hi Team,
Please list all patches required for installing the configuration management workbench in Oracle Apps version 11.5.10.2 ?
Please let me know.
Thanks,
Suman V.

Hi;
I also suggest to check:
How to Configure the Oracle Configuration Manager with Support WorkBench [ID 1174943.1]
Regard
Helios

Already i download driver for install the windows, i can get the drivers but i can't install windows, how i can install windows without downloads driver again

already i download driver for install the windows, i can get the drivers but i can't install windows, how i can install windows without download driver again

This seems to be a commercial product. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
You can find the Commercial Laserjet board here:
http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

The step-by-step guide for installing the Oracle Database and Oracle9iAS Portal

All,
I made a step-by-step guide for installing the Oracle 8.1.7 database and Oracle9iAS 1.0.2.1 (HTTP Only) install on a 'clean' Windows 2000 machine. The guide has a screen shot of every single step that I went through to get an installation of the database and Oracle9iAS Portal to work.
Because I left my email in the guide, everyone will be sending me email with questions about their particular install. [What I really wanted was some positive feedback email to show to my manager... hint hint.] As I do not want to troubleshoot everyone's install by email, I started this thread.
Let's start the step-by-step install guide discussion here.
As a start, here is what I did NOT want to do with the guide: I did not want to 'redo' the current Oracle9iAS installation guide. So I did not put any conditions in the guide. This is just what I had to do to take a clean Windows2000 machine (no Oracle software on it) and get it to work. If I keep on adding conditions, eventually I will end up with the installation document.
Also, in the next version (for the Oracle9iAS 1.0.2.2) I will probably start over again from scratch as we are planning on addressing some of the issues with the install.
Another thing I plan to do is put the following direct links in:
Oracle9iAS Portal: Troubleshooting Guide
Oracle9iAS Portal: Diagnostics Tool
Oracle9iAS Portal: FAQ
Have a look at the above, as they will answer probably all of your questions... But if not post away!
Thanks,
Rich

We do have installed a Lotus Notes LDAP. Unfortunately, the documentation is company internal in German.
The steps, in general, where:
1) Create physical connection (obviously, you did that)
2) Deploy the XML Descriptor for the LDAP under "UM Configuration => Data Sources"
We used a derivate of the Sun One LDAP Profile.
3) Match the assignement LDAP Group --> EP Role --> EP User via EP user management
4. The user, in our case, is always created in the LDAP first (from a different LDA administration group) and is then visible in the Portal)
I know, this is very generic, but the "magic" is in the XML profile and I haven't seen any documentation about it yet.

XML data set picture gallery for thinkbox/lightbox/lightwindow ?

Hi, I want to do a gallery using thickbox or lightwindow or
lightbox. I have the pictures in XML file. How can I make a
pictures gallery using data set. I loaded the XML hive and I
pointed to the pictures and gave them ds1
but when I put link reference to {perspImage}
I click the link and I get new browser window not even
lightwindow. Can someone with some experience help?
(I linked all scripts, css already in the HTML and I tested
it on a single picture and it worked but I need to get a gallery
based on images in XML file) please help.
Thanks

I managed to mash Spry/thickbox/jquery/XML together
http://www.stjohnhistoricalsociety.org/Photographs.htm)
several years ago. I can't really remember the details very
well - but I
had to reverse the normal sequence of thickbox magic
enhancement followed by Spry region expansion.

Help for install the mac Os x 10.4.11

Halo everyone!!
I Have a Mac Mini (PowerPc G4) , but he don´t Install the Mac Os x 10.3.1 , and my drive disk presents problem for read the disc , have as , install the Mac Os X for USB Drive ? and there how download the Mac Os X for apple suport ?
why my current Mac Os X this corrupted he is (Mac OS X 10.5.8) but Because problems i prefer the Mac os X Tiger
I thank the help

Is the 10.3.1 Disc the original one for this Mini series, or for another Mac?
You can't download 10.4, & it can be expensive...
http://www.ebay.com/sch/i.html?_nkw=mac+os+x+tiger+retail+10.4
See Tom's, (Texas Mac Man), great info on where/how to find/get Tiger...
https://discussions.apple.com/message/15305521#15305521
Or Ali Brown's great info on where/how to find/get Tiger...
http://discussions.apple.com/thread.jspa?messageID=10381710#10381710
Do you have the 10.5 Install Disc?

Where are _correct_ directions for installing the Adobe Flash Reader plug-in

There are directions for installing Adobe Flash Player in its new Firefox incarnation as a plug-in rather than its old incarnation as a stand-alone program. Unfortunately, the directions are not for the current versions of either Firefox or Adobe Flash Player, and not only don't work, but don't even make sense. Are there _correct_ directions somewhere that will let a reasonably naive user install this plugin? Following the existing directions get conformation at ever step that the installation has succeeded, but in the case, nothing is there to run. As a result, that huge fraction of the web using Adobe Flash Player is now broken for me.
== This happened ==
Every time Firefox opened
== Firefox changed Adobe Flash Player to be used as a plug-in.

There is no stand-alone Adobe Flash; never has been that I recall. The following will install the plugin.
'''Install/Update Adobe Flash Player for Firefox (aka Shockwave Flash)''': your ver. N/A; current ver. 10.1 r53 ('''important security update 2010-06-10'''; see: http://www.adobe.com/support/security/bulletins/apsb10-14.html)
~~red:Check your version here~~: http://www.mozilla.com/en-US/plugincheck/
See: '''[http://support.mozilla.com/en-US/kb/Managing+the+Flash+plugin#Updating_Flash Updating Flash]'''
-'''use Firefox to download''' and '''SAVE to your hard drive''' (save to Desktop for easy access)
-exit Firefox (File > Exit)
-''In Windows,'' check to see that Firefox is completely closed (''Ctrl+Alt+Del, choose Task Manager, click Processes tab, if "firefox.exe" is on the list, right-click "firefox.exe" and choose End process, close the Task Manager window'')
-''In Windows,'' double-click on the Adobe Flash installer you just downloaded to install/update Adobe Flash
-when the Flash installation is complete, start Firefox, and test the Flash installation here: http://kb.adobe.com/selfservice/viewContent.do?externalId=tn_15507&sliceId=1
*'''NOTE: On Vista and Windows 7''' you may need to run the plugin installer as Administrator by starting the installer via the right-click context menu if you do not get an UAC prompt to ask for permission to continue (i.e nothing seems to happen). See this: http://vistasupport.mvps.org/run_as_administrator.htm
*'''NOTE for IE:''' Firefox and most other browsers use a Plugin. IE uses an ActiveX version of Flash. To install/update the IE ActiveX Adobe Flash Player, same instructions as above, except use IE to download the ActiveX Flash installer. See: [[ActiveX]]
*Also see: http://kb.mozillazine.org/Flash ~~red:'''''AND'''''~~ [[How do I edit options to add Adobe to the list of allowed sites]]
'''''Other Issues''''': ~~red:You have installed plug-ins with known security issues. You should update them immediately.~~
'''Update Shockwave for Director (aka Shockwave Player)''': your ver. ~~red:10.1 (very old)~~; current ver. 11.5.7.609 (important security update released 2010-05-11; see http://www.adobe.com/support/security/bulletins/apsb10-12.html)
NOTE: this is not the same as Shockwave Flash; this installs the Shockwave Player.
~~red:Check your version here~~: http://www.mozilla.com/en-US/plugincheck/
SAVE the installer to your hard drive (Desktop is a good place so you can find it). When the download is complete, exit Firefox (File > Exit), locate and double-click in the installer you just downloaded, let the install complete.
See: '''[http://support.mozilla.com/en-US/kb/Using+the+Shockwave+plugin+with+Firefox#_Installing_Shockwave Installing Shockwave]'''
'''Install/Update Adobe Reader for Firefox (aka Adobe PDF Plug-In For Firefox)''': your ver. ~~red:8.2.3 (very old)~~; current ver. 9.3.3 (important security update release 06-29-2010; see: http://www.adobe.com/support/security/bulletins/apsb10-15.html)
~~red:Check your version here~~: http://www.mozilla.com/en-US/plugincheck/
See: http://support.mozilla.com/en-US/kb/Using+the+Adobe+Reader+plugin+with+Firefox#Installing_and_updating_Adobe_Reader
''You may be able to update from the Adobe Reader installed on your system'' instead of going to the Adobe site and downloading. Start > Program Files, find and click Adobe Reader to open, click Help, click Check for Updates. Allow the download/update to occur. If you use this method, no need to proceed with the instructions below, '''but''' do look at the two bulleted items at the bottom "'''NOTE for IE:'''" and "Also see:". Restart Firefox and check your new version here: http://www.mozilla.com/en-US/plugincheck/
''If you go to the Adobe site to download the current Adobe Reader:''
-'''use Firefox to download''' and '''SAVE to your hard drive''' (save to Desktop for easy access)
~~red:-See the images at the bottom left of this post to see the steps to take on the Adobe site~~
-exit Firefox (File > Exit)
-check to see that Firefox is completely closed (''Ctrl+Alt+Del, choose Task Manager, click Processes tab, if "firefox.exe" is on the list, right-click "firefox.exe" and choose End process, close the Task Manager window'')
-double-click on the Adobe Reader installer you just downloaded to install/update Adobe Reader
*'''NOTE: On Vista and Windows 7''' you may need to run the plugin installer as Administrator by starting the installer via the right-click context menu if you do not get an UAC prompt to ask for permission to continue (i.e nothing seems to happen). See this: http://vistasupport.mvps.org/run_as_administrator.htm
*'''NOTE for IE:''' Firefox and most other browsers use a Plugin. IE uses an ActiveX version. To install/update the IE ActiveX version, same instructions as above, except use IE to download the ActiveX installer. See: [[ActiveX]]
*Also see: http://kb.mozillazine.org/Adobe_Reader ~~red:'''''AND'''''~~ [[How do I edit options to add Adobe to the list of allowed sites]]

I need Help for Installing the JamVM on TS-7800 SCB

Hello,
can anyone give me some StarterHelp to install the JamVM (or any other VM) on the follwing SBC (Arm)?
http://www.embeddedarm.com/products/board-detail.php?product=TS-7800&tab=options
Didn't need I a crosscompiler for the target-arch? In the INSTALL-File of the jamvm-package i didn't reed somthing about using a crosscompiler.
For you help i'm very thanksfull.
Best regards.

can u guys solve the problems??? i also working on the ARM board which came from China. my problem also almost the same.still configure how to run the java program on that board. i just read from this journal, http://www.linuxjournal.com/article/8757. this author said that we don't have to install JVM in our target. we just have to use GCJ (GNU Compiler for Java), which is will compiles our Java source down to the machine code for the target. but, the author used PowerPC target, that was the issue. i already try this method but it was not working yet. i also don't know why yet.please let me know if u guys can slove your problems. tq~

What are the pros and cons for installing the OS X Yosemite while still using Adobe CS6 Softwares?

Having trouble understanding what are the benefits to install the new operating system for my iMac?

Having trouble understanding what are the benefits to install the new operating system for my iMac?

Please help me! I have gone through the steps for installing the newest version of Flash Player (at

least a dozen times and it says it is installed but afterwards, it is not. HELP!

first, uninstall fp, http://helpx.adobe.com/flash-player/kb/uninstall-flash-player-windows.html
then manually download and install the latest fp, http://www.adobe.com/products/flashplayer/distribution3.html

Any warnings or tips for installing the FSCM 9.2.001 Upgrade Image on VMware rather than on Oracle VirtualBox?

Our Network services group is pushing back the use Oracle VirtualBox since we have VMware as our standard. We have decided to not fight it, and install our upgrade and Update images on VMware. Did anyone experience any issues on VMware? And, if so, was there an easy enough workaround? Or, was it seemless? Thank you!!

I don't understand which instructions I have to make for oracle upgrade?
-- You have to follow all the instructions mentioned
(Just check for few if's for Cluster enabled, OID and OLAP databases. Perform these steps only if they apply)
Must I also make the 3. instruction? Connect to databse prior and drop?
-- Yes you should do
Must I also make the post install action for my database?
(startup migrate ...)
-- Yes. Do run catpatch.sql .
what means at post install actions the following:
'execute these post install actions only if you have one or more databases associated to the upgraded $oracle_homee.
-- In this step make sure you do step 1
1: Java VM and XML DB Requirements
Otherwise catpatch.sql will fail.
Do 2 and 3 only if applicable
Chandar
My database path is e:\oracle\oradata\database my oracle path is e:\oracle\ora92 have I in my case make the post install actions?

What is a proper location for installing the Trial?

(C://Program Files is not working...)

I am trying to download the Trial for CS6. Sorry I thought these question were specifically for issues with the 30 day Trial. This computer is running Windows XP. The default save location is C://Program Files. There is no error number. Here's what the error says:
"Adobe Download Assisstant
Sorry, an error has occured.
The application could not be installed at the selected location. You may not have sufficient privileges. Try installing to a different location or contacting your administrator."
I think you're right - seems like the problem is on the computer's end. I'm pretty bad with computers though so you'll have to tell me.
Before contacting an administrator (lengthy process), I want to get around the issue by trying on my own (i.e. maybe installing to a different location). Can you suggest other locations good for doing this or any alternative solutions?

HT1222 I dont know what password they need for installing the latest version of itunes because it isnt the same as my apple id

How am i supposed to download the latest itunes version if i dont know the password because its not the same as my apple id password

The password being requested is, as for any Mac OS X software update or application installation, the password to your user account in Mac OS X, or the user name and password to an account in Mac OS X that has administrator privileges if your account does not.
Regards.

Picture gallery for installing the MaxUpgrades P/N SZ-MP2009OPT06

Similar Messages

Maybe you are looking for