Pin connector for front headphone ja

The front headphone jack cable connection on my Dell 4600 is incompatible with my new Xtreme Gamer soundcard's male pin connection. Can anyone tell me where to find the correct female pin connector, and how do I know which leads go to which pin slots?Thanks?

more or less to adapt the here is the crude way to do it. DO AT YOUR OWN RISK. . Check to see if you have some slack from /8-/4" of an in in cable is going bye bye.2. Cut all the wires or the cable with all the colored ones in them about /2-" up the line.3. Strip exposed ends as to allow splicing on the Blue, Green, Yellow, Orange, Red, Black, and brown cables only.4. on the plug side twist together these wire colors [The should always be back to back]:?Blue and Green??Yellow and Orange5. Splice the wires together from plug piece to wires goint to front:??[Blue+Green {Step 4}] to just the Blue Wire?The Purple and Navy Blue that went into the hole next to plugged are not used trim all off plug.
[Yellow +Orange{Step 4}] to just the Yellow wire.
Brown to Brown?Black to Black?Red to Red6. Check your work: Wires not connected that lead to front of computer should be: Grey, Orange, Purple, and Navy.7. Use electrical tape to cover exposed splices area on each splice. Make sure tight at least 2 rotations.8. Use electrical tape to wrap all wires together and tightly.9. Plug the newly rewired plug into your SB Card.0. DONE.

Similar Messages

  • MOVED: 3-pin connector for fan

    This topic has been moved to Overclockers and Modding Corner.
    3-pin connector for fan

    Generally, the 3 pin connector on VGA cards is smaller than the CPU fan connector on a motherboard. You would need a converter or you may aslo need to mod the connector on the Zalman.
    You could check to see if the actual contacts between the two are the same, in some cases I have been able to use a dental pik to remove the contact pins from the female connector of the original fan's connector and install it into the larger size connector but it's been so long since I have done it. In some cases I have been able to find the little metal contacts at an electronics store and crimp them on myself.
    Since this is not an MSI product and this is an MSI forum, I have moved this topic from the VGA forum to here.
    Good luck.

  • Need the SCSI-II 100-pin connector for the PXI-6624

    Hi. I need to build a custom cable for the NI PXI-6624 and I would like to know where can I get the 100-pin connectors. Thank you.
    Daniel
    Chile

    You should be able to find the connectors here:
    Subminiature and Microminiature D Connectors .050 Series Cable Connectors (SCSI)AMP (749111-8)
    The parts are made by Tyco Electronics P/N: 749111-8
    Otis
    Training and Certification
    Product Support Engineer
    National Instruments

  • MS6167, USB pin outs for front port

    Can anybody tell me again the pin assignments of front usb header of MS6167.  I remember somebody figured  this out but that was quite a long time ago (may be almost two years ago).  The manual only indicated pin1 but no description and location of the other pins.  I contacted MSI regarding this matter but they rather refer it to you guys...he he.  Please help!  So I can install a usb port at the front of my pc casing.  I've read that wrong connection to the usb port can result to frying my precious usb device (my Acer usb external cd writer)

    Hey James,
    I've just sussed this one out, although I've used a back panel bracket:-
    I've purchased a Belkin F3U001 and successfully fitted it to my USB Front Header. Everything appears to be AOK.
    Just for any other interested MS-6167 owners the pins are (as per Motherboard):-
    5V/VCC * * Ground
    USBD0- * * Ground
    USBD0+ * * USBD1+
    Ground * * USBD1-
    Ground * * 5V/VCC (marked as 1 in Manual)
    This relates directly to Example D in the Belkin F3U001 Installation Instructions.
    Cheers,
    Pete.  :D

  • I need a 9-Pin Connector for a G4Ti4600 VTD

    What do I do? ?(

    Are you in the US? Order one from here:  http://store.apple.com/us/browse/home/shop_mac/mac_accessories/power?mco=MTM3NjU xNDg
    Or check out Best Buy.

  • ~~KT4V~~ Front Panel Pin Connectors (USB + Audio)

    Hello All
    I have a few questions on setting up the front panel pin connectors from my case to my new KT4V board.
    First question: USB
    My case is usb 2.0 (Raidmax Scorpio)it has two seperate pin connectors a 4 pin and a 4 pin + GND pin on the second wire. I assume I put the GND in the JUSB1 #10 slot which is marked (USBOC) in my manual. Is this correct?
    Second Question: Front Audio (Microphone, Headphones)
    The front panel Audio Connector: JAUD1
    The four pin connectors that my case has labeled is:
    1. MIC DATA
    2. MIC GND
    3. EAR R
    4. EAR L
    I am pretty sure MIC DATA goes in pin #1, and MIC GND goes in pin #2. As far as both EAR pins, I am not sure and would appreciate some help in this.
    Thanks in advance.
    ncarme  :D

    I know, I have the book in front of me. But the names on the board and my case are different. Thanks for the info on the usb, how about the audio inputs.
    Thanks.
    ncarme

  • Front Panel connector for JAUD1 on K9A2 Platinum mobo

    I bought some headphones for my computer and they work well when plugged into the line out and mic on the back. It's a pain unplugging my speakers in the back and plugging in the headphones, then switching back when I want my speakers again.
    I noticed there is an internal JAUD1 connector which suggests that I can attach a front panel audio device to it. Where can I get such a device and what is it called ( I can look on New Egg if I know what to look for ) ? Does MSI sell one ? Does it attach in front into one of my drive bays ( I have lots of them in a Lian Li case ) ? If I have the device attached and plug my headphones into it, can I listen to audio through my headphones without having to unplug my speakers ?

    Quote from: eldiener on 06-January-11, 01:23:43
    My case is about 10 years old I believe. It is a Lian Li PC-70USB Full Tower ATX Case and it still is excellent. But it did not come with a front panel audio connector. Is it possible to buy one anywhere which can fit into a drive bay and which connects to the JAUD1 on the K9A2 ? I will search New Egg for "front panel audio connector", and I will ask Lian Li if perhaps they have one for older cases.
    You can buy a new soundcard that comes with some front panel bay too ,though is much more expensive than a simple new case.
    If you managed 10 years without a front jack why would you want it now ?!
    Buy some USB headshones ,if there is a front USB connector ,maybe you get even better sound quality.
    The sound on the Platnium is not so great anyway ,i ve turned it off in the first 2 months of usage to use either X-FI either D1 which are much better sound wise.

  • TS2634 I bought a composite AV cable with 30 pin connector at a proper apple store for my ipad 2 which no longer works now i have updated to ios7 - please advise how to make this work ?

    I bought a composite AV cable with 30 pin connector at a proper apple store for my ipad 2 which no longer works now i have updated to ios7 - please advise how to make this work ?

    I have the same problem.
    Two similar discussions:
    https://discussions.apple.com/message/23081658#23081658
    https://discussions.apple.com/message/23281391#23281391
    I have not yet seen any official response to the question: "Is the Apple AV Composite cable fully supported with 30pin connector devices upgraded with iOS7 - specifically ? - eg. iPad 2, iPhone 4, iPhone 4s"
    If it is not currently supported is that then due to a bug / oversight and in that case is it something that will be fixed in the near future?
    Please let us know what feedback you got from asking Apple support.

  • Pin definition for TV OUT Connector (C&S)

    I`ve bought graphic card MSI GeForce4 Ti4200 TD 64MB but there was no the cable for TV connecting. I`ve bought the cable, but it does not work. Do anyone knows the pin definition for " TV_OUT Connector (C&S)", because I can`t find it in user`s guide.

    Could you help me? I own a FX 5200 8907 TD128, and the 4 pin S-Video outputs B&W image. The card came with a S-Video to RCA cable, but it isnt useful. Software setting doesnt have an effect. When in the POST the TVoutput is enabled by default and it outputs color images!. Changing PAL from NTSC doesnt have an effect. I did this with 2 RCA TVs and with a VCR. Still Black and White!!!.
    I thought i had to buy a new cable but in the setup or during Windows load the outputs works good. May it be a VGA BIOS problem???
    PLEASE HELP

  • Where can I find the pin-outs for 8-pin remote Hirose connector?

    Where can I find the pin-outs for 8-pin remote Hirose connector?

    Pin outs and wiring info is all in the Maintenance Manuals (same for all system cameras, F series, XDCAM etc.), - ask your local Sony Office if you want the info.The 8pin remote is for connection to the Sony RM-B150/170/750 remote control panels.For system cameras the same protocol is used between RCP panels, MSU, CCUs and camera heads.It is a proprietry system so extremely difficult to hack!The RM-B170 is the ideal panel to work with the PMW-F5/55. It will give basic painting control of R/B white & black painting, Master Pedestal, and Iris with the correct lens (Cabrio etc). It can also control remote Rec stop start.Regards, Clive. Sony ANZ.

  • Are there any headphones that work from the 30 pin connector?

    Are there any headphones that work from the 30 pin connector? Neither of my kids auxilary ports on their iPhone/iPods work.  Need another way to use with headphones.

    http://www.sonicelectronix.com/item_14260_1PR2-Universal-iPod-Adapter-to-RCA-Aud io-Connection-Cable-w-Charging-Capabilities.html

  • 16 pin PCB Mount connector for NI USB-6212

    I have the scew-terminated NI USB-6212 and am looking for a connector that will allow me to plug in an external PCB.  If anyone could provide a part number it would be greatly appreciated. 

    Poke around on Digikey and see what they have that suits your needs.  It's a 3.81mm-pitch connector, Phoenix Contact makes a bunch in their Combicon line. 
    NI also offers an OEM-flavored 6212 that has a standard 0.1"-pitch header on it.  For interfacing to a custom PCB, this is very much a better way to go. 
    DAQ mates right up to that 50-pin connector on my board.  (I'm using a 6211 with one 50-pin header on this product.)

  • Pin out for connector block - CB-50LP (50 pins)

    1. Need pin out designation for 50 pins connector block, for use in multifunction DAQ (6024E)
    2. Connections from 6024E to 68 pins connector block.

    1.  How are you connecting the 6024E to the 50 pin connector block?  Any special 68 to 50 pin cable or adapter should have a pinout that comes with it.  If you have an NI cable or adapter you should be able to look in that part's manual online at ni.com and find this pinout.
    2.  What specific 68-pin connector block are you using, is it an SCB-68?  For an SCB-68 the pins on the connector block are mapped to the same pin on the 6024E or any E-Series and most M-Series boards.  The pinout for the 6024E will be the pinout for the SCB-68. 
    Jason N    

  • Diagram showing the connector pin assignments for a TBX-68 terminal block

    Could someone provide me with a diagram showing the connector pin assignments for a TBX-68 terminal block? The terminal block is connected to a PCI-6204E board.
    Thank you for your time
    Andrew Lockyer

    Since pins 1 through 68 are clearly marked on the terminals, I'm guessing that what you really want is the pin out of your DAQ board. That information should be in the manual that came with the board. I could find no reference to a 6204 board on NI's site so I can't point you to an electronic version that you can download. Double check the model number of your board. Once you locate the manual and the pin out of the 68 pin connector on your board, then everything else is simple. Assuming you have a 68 pin ribbon cable connected between the board and the terminal block, then pin 1 on the board is pin 1 on the terminal block, etc.

  • Need 50-pin connector pin assignment list for valuemotion NuDrive 4SX-411

    Hi,
    I need a copy of the 50-pin connector pin assignment list for the valuemotion NuDrive 4SX-411.   I have the 321942B-01 User Guide document, but it does not contain the pin assignement list.   I can't find the information on NI's website.
    David Geminden

    You can find the pin assignment in the user manual of the PCI-7314/7324 ValueMotion controller. On page 38 in this document there is the 50 pin assignement of these boards, that is compatible to your NuDrive. Please note that this is the pin assignment from the controller's point of view.
    I hope this helps,
    Jochen Klier
    National Instruments

Maybe you are looking for

  • Yoga 2 Pro audio jack problem

    Greetings, Please know that I am not tech-savvy....at all!  I have been researching this prpblem for about a week, and did find some posts here that are similar to my problem but the 'fix' didn't work  I have owned my new Yoga 2 Pro 64 bit with Windo

  • ABAP code help

    Related to the previous question, the SHIFT command does not recognize the '#' sign over there. it does not eliminate so what I have used before to remove it is. this is the logic.. if znewlawsoncode+??? na 'abcdefghijklmnopqurstuvwxyz'.        shift

  • Password Manager 4 and IE9 webpage failure

    I have Password Manager 4 installed on my W520 Windows 7 SP1 -64Bit OS. I am experiencing an IE9 failure when accessing a particular webiste; The error displayed is as follows: I've isolated the issue to the following add-on: IePasswordManagerHelperC

  • Can I somehow teach my 6th gen Nano to tell me how far I've walked in miles rather than "steps," by telling it how long each of my steps is?

    Using the pedometer in a 6th gen Nano: Currently, it (very accurately) tells me how many steps I've taken when I go for a walk. Works fine. Meanwhile, on my own, I carefully calculated how far each of my "steps" is (2.231 feet/step, in case you're cu

  • Re-generating a report in transaction rsrt

    Hello All, Please advise on how to re-generate a report in transaction rsrt. Please also advise on what re-generating a report actually does. Thank you in advance. Regards, Keith