Pin definition for TV OUT Connector (C&S)

I`ve bought graphic card MSI GeForce4 Ti4200 TD 64MB but there was no the cable for TV connecting. I`ve bought the cable, but it does not work. Do anyone knows the pin definition for " TV_OUT Connector (C&S)", because I can`t find it in user`s guide.

Could you help me? I own a FX 5200 8907 TD128, and the 4 pin S-Video outputs B&W image. The card came with a S-Video to RCA cable, but it isnt useful. Software setting doesnt have an effect. When in the POST the TVoutput is enabled by default and it outputs color images!. Changing PAL from NTSC doesnt have an effect. I did this with 2 RCA TVs and with a VCR. Still Black and White!!!.
I thought i had to buy a new cable but in the setup or during Windows load the outputs works good. May it be a VGA BIOS problem???
PLEASE HELP

Similar Messages

Pin layout for TV out header on RS480M2-il motherboard

Hello,
Does anyone know where I might find the pin information for the TV out header on this board (MS-7093)? I have the version with the COM port on the back panal rather than the TV out connectors, and can't find the MSI TV bracket anywhere, but have found something I could use if I knew which pin carried the composite signal.
Is there any risk of damaging anything if I just go by trial and error; there are five pins on the motherboard, the others being for s-video.
Thanks for any advice,
Frazer

MOBO for ms-7093 RS482M2 http://global.msi.eu/index.php?func=proddesc&prod_no=214&maincat_no=1#
manual for the RS482M2 http://global.msi.eu/index.php?func=downloaddetail&type=manual&maincat_no=1&prod_no=214
The TV out is JTV1
The manual is your friend. Pg 2-17

Fault pin invalid for PWM out?

LabVIEW for ARM 2009
Luminary chip
Whether the picture options are not checked, no matter Fault pin high or low, PWM Pins always signal output?

It's a rather self explanatory problem. Your axi_pwm_0_PWM_Out is 4 4 bit port but the external pin axi_pwm_0_PWM_Out_pin you defined is single bit only. Make axi_pwm_0_PWM_Out_pin into 4-bit wide and your problem should go away.

Is my 'pin number' for porting out my number the same as my 'billing password'?

Also I'm on a family plan, if there's one 'pin number', does the whole family share that one pin or is it by device?

When you port you need your cell number, your Verizon wireless account number and the account pin. The pin normally is the last four digits of the account owners social security number.
Please note if you are just a line on the master account only the account owner can port the number over to another carrier.
Good Luck

Diagram showing the connector pin assignments for a TBX-68 terminal block

Could someone provide me with a diagram showing the connector pin assignments for a TBX-68 terminal block? The terminal block is connected to a PCI-6204E board.
Thank you for your time
Andrew Lockyer

Since pins 1 through 68 are clearly marked on the terminals, I'm guessing that what you really want is the pin out of your DAQ board. That information should be in the manual that came with the board. I could find no reference to a 6204 board on NI's site so I can't point you to an electronic version that you can download. Double check the model number of your board. Once you locate the manual and the pin out of the 68 pin connector on your board, then everything else is simple. Assuming you have a 68 pin ribbon cable connected between the board and the terminal block, then pin 1 on the board is pin 1 on the terminal block, etc.

Scale definition for theme is out of range

Hi,
I am getting the following error when viewing a FOI layer using mapviewer javascript API
[oracle.sdovis.theme.pgtp] Scale definition for theme is out of range.
Once I've got this error, I need to restart oc4j again in order for the map to come up.
I've set the dimension info to -180<x<180, -90<y<90. I am able to see the theme in mapbuilder or perform spatial query. Any idea what might went wrong?
Thanks

I noticed the error is caused by not setting the initial map center and zoom level. Once I added the following code, the error went away.
mapview.setCenter(MVSdoGeometry.createPoint(-122, 37,8307));
mapview.setZoomLevel(4);
What I don't understand, however, is why can't I use FOITheme.zoomToTheme() to replace the code above?

How can I find out my PIN number for my old ipad that has been disabled

I need help to find out my old PIN number for my old ipad it has been disabled as I can't remember what my pin is

http://support.apple.com/kb/ht1212

Dimensions of the 160-Pin Cable for the NI PXI-2530B

Hello,
My mechanical design team wants to know the measurements of the 160-Pin Cable for the NI PXI-2530B. It will be a while before we receive the cable we ordered. I could not find a data sheet with the measurement details; are they? Alternatively, is Figure 1 in the Installation Instructions drawn to scale?: http://www.ni.com/pdf/manuals/375656b.pdf
Thanks!
Solved!
Go to Solution.

JKSH wrote:
Hello,
My mechanical design team wants to know the measurements of the 160-Pin Cable for the NI PXI-2530B. It will be a while before we receive the cable we ordered. I could not find a data sheet with the measurement details; are they? Alternatively, is Figure 1 in the Installation Instructions drawn to scale?: http://www.ni.com/pdf/manuals/375656b.pdf
Thanks!
What dimensions are you looking for?
I'm a little surprised that the length of the cables is not included in the datasheets (I did just look!) - I thought that when I ordered cables for the older-style PXI-2530 modules in my lab that the length was specified in the part description.
If you need the dimensions of the connectors, you can do a little reverse-engineering and identify the dimensions of the various components. The connector to the module is an LFH-160. The Digikey P/N for the body of a connector is WM4099-ND. It may be difficult to find the dimensions of the backshells, however. The 4 terminal block connectors are standard 50-pin D-Subs. There are many examples out whose dimensions you can review.
Jeff
Jeffrey Zola

How to create a page-definition for bounded task-flow?

I should be able to create a page definition which declare all bindings required for a bounded task flow.
How do I do it in JDeveloper 11.1.1.2?
How do I navigate to the page definition when I am in the bounded task flow "Diagram tab"?

I found out the following:
1. To create a page-definition file for a bounded task flow
Right click on the "Default" activity (not a view activity) of the bounded task flow, select "Create Page Definition" from the context menu.
2. To go the page-definition file for a bounded task flow
Right click on the "Default" activity (not a view activity) of the bounded task flow, select "Go to Page Definition" from the context menu.
My new question is:
In JDeveloper 11.1.1.2, how do I create page-definition for a bounded-task-flow if all activities are view activities (page fragments) ?
How does JDeveloper I want to create page-definition for the task-flow instead of create page-definition of the page fragment or the page?

Receiver server definition for file adapter

Hi,
I am trying to create a scenario where the data from SAP system goes to XI through ABAP proxy and has to write the data in the file.
My Question...
In the Integration directory my sender system is ABAP Proxy and receiver system is File adapter.
When I try to create a distribution channel of type XI adapter, I cannot select it as sender. By default it comes as receiver. How Do I go about doin this scenario.
Also, since I have to write to a file, it is my receiver(outbound adapter). Please can anyone tell me what would be the service definition for this as I am writing to a directory!!!
Thanks in advance.

Hi ,
That is what I have done.
XI Adapter(ABAP Proxy) is my sender system.
File adapter is my receiver adapter.
But I am unable to make a distribution channel with XI adapter as sender. The radiobutton of receiver is only active and I am unable to select the sender radio-button. Is this some sort of error.
Actually when I select XI, HTTP, IDOC and RFC adapter in communication channel, the receiver radiobuttion is selected by default and I am unable to select on sender radiobutton.
Have we missed out on any configuration?
thanks in advance

Editing XMP metadata in Bridge for checked-out files?

Our custom connector does not implement the WRITE_XMP_METADATA Capability because we do not want to change the XMP of a file in our DAM system without checking in a new file version.
However, when a file is checked out through Adobe Drive, we would expect to be able to edit its XMP metadata in Bridge just like we can for local files.
It looks like this is still not possible with Adobe Drive 3, i.e. if your connector does not implement the WRITE_XMP_METADATA Capability you cannot edit XMP for checked out files either.
It seems weird that you can edit XMP metadata for checked out files with regular CS applications but not with Bridge. Is this something that is expected to be fixed in a future version?
Thanks

In our design, editing XMP data in Bridge and in regular CS applications is different, the former one will be routed to SetXMPHandler in you connector, in the latter case, CS applications take the normal file writting ways to embed XMP data in the file content.
The purpose of this design is to offer similar user experience for normal users when they edit XMP data for AD assets and local file assets, they don't need to check-out files first.
To address your issue, I think you can add some codes in SetXMPHandler to auto check-out files before real XMP operation, and check-in them before exiting the handler
We will consider to make some enhancements for this part, that's, to allow editng XMP data for the checked-out files in Br, in the next release, thanks for this advice.

How can i remove the end pice/pin from my headphones out of my computer?

how can i remove the end pice/pin of my headphones out of my computer?

IF you cannot pull it out with your finger tips, you need to take the machine in for service to an Apple Store or AASP. Doing this type of work yourself could seriously damage the computer so it's best left to professionals.

Is the "Device Class Definition for Physical Interface Devices" specification implemented in Windows?

Can I assume that Windows will be able to handle my physical interface device if I follow the "Device Class Definition for Physical Interface Devices" specification while writing the firmware?
I'm trying to develop a device which handles rumble output from applications such as games. Applications would include e.g. racing games or simulators. I'm hesitant to just clone Xbox 360 Gamepad or Sidewinder USB reports. I'd like to correctly declare my
device as something on its own while still making use of already implemented OS-specific drivers. The purpose of the mentioned specification is exactly that as far as I can tell. I wasn't able to find concrete information about its level of support though.
The "USB device class drivers included in Windows" page (sorry I'm not allowed to post links yet..) seems to link to WinUSB which I'm not sure what to do with.

Thanks for your response. Well if everything was implemented at that time and it's still available it should be fine since the specification document's last version is dated 1999. I was just hoping there would be any form of documentation whether it's
supported and by which degree so I don't go through the trouble of figuring out how the firmware should be written according to the specification just to find out there is no OS driver implementation for it which would render my work more or less useless.
So I suppose I'm forced to go the trial and error path?

DW MX Site Definitions for Verizon FIOS? Mac

Hello, Everyone,
First time poster, longtime user/dabbler. All help is greatly
appreciated.
I'm using DreamWeaver MX for Mac and trying to do a site
definition for Verizon FIOS. The instructions on their web site do
not work, are sketchy at best anyway, and Verizon's tech people
don't give tech support on this in general and don't know the
answers so far!
Does anyone know what to put in the fields for an ftp
connection in site definition? Really - is anyone successfully
using DreamWeaver with Verizon fiber optic?

Send me your connection info offlist, please -
forums at great hyphen web hyphen sights dot com....
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"frankELF" <[email protected]> wrote in
message
news:[email protected]...
> Thanks for responding, Murray!
>
> Here is the meat of what is on Verizon's FIOs web site:
> QUOTE
> 2. Launch your FTP client.
> 3. If a dialog box does not automatically open, there
should be a
> prominent
> button or menu item for connecting to a remote host -
activate it.
> 4. In the dialog box that appears, you will need to
enter the following
> information:
> * HOST NAME: ftpmysite.verizon.net
> * User Name: your user ID (e.g. - jsmith)
> * PASSWORD: your password
>
> At this point, you should be connected to your site on
the Web server.
> ENDQUOTE
>
> In DreamWeaver MX, I put the HOSTNAME stuff in the field
for FTP Host. For
> the
> mysite part of the name there I put my subaccount email
address prefix
> [what I
> have before the @ part]. I put ftp with and without a
dot after it, and
> tried
> leaving out ftp.
> Where they ask for User Name, I again put in my
subaccount email address
> prefix in the DWMX Login field. The prefix happens to be
survivorevents.
> For PASSWORD, of course I put in the password for the
email subaccount.
> For Dreamweaver's Host Directory, I left the field empty
as I do with my
> cable
> internet company.
>
> The only thing that I DIDN"T DO that they mention
elsewhere on their site
> is
> to use the extension htm for my index file. I left mine
at html. I
> wouldn't
> think that would matter.
>
> I have been using a cable company that allows multiple
email addresses.
> But Verizon does a strange thing: there is a main
account and the rest are
> SUBemail accounts of the main one. For some reason, that
made it
> impossible for
> me to set up Apple's Mail application without the help
of tech support
> from
> Verizon. It is otherwise quite literally impossible. You
need to know what
> Verizon calls the subaccount, which is completely
different from what I
> enter
> it as.
>
> I did get the Verizon version of the name of the
subaccount and entered it
> under user name and that didn't help.
>
> In short, HELP!
> As always, any ideas are greatly appreciated.
> Sorry for the yelling.
>
>

IMP-00093: Inconsistency between dumpfile constraint definition for table

I am getting the following error while importing table. I have checked and I can see the table and constraint exist.
Anyone know in what situition this warning will be trigger out? Will this warning give any impact to the table or database ? any solutions?
Export file created by EXPORT:V09.02.00 via conventional path
import done in US7ASCII character set and AL16UTF16 NCHAR character set
. importing PROD_USR's objects into PROD_USR
. . importing table "FLPBABA" 29 rows imported
IMP-00093: Inconsistency between dumpfile constraint definition for table FLPBABA with columns ("FQ_FLPBABA_UPD_TMS" , "F9_FLPBABA_B4_AFTER")
Import terminated successfully with warnings.
Message was edited by:
cocorico78

The full error message might explain a little.
Oracle Error :: IMP-00093
Inconsistency between dumpfile constraint definition for table string with columns (string)
Cause
Import failed to locate a base table for a constraint that was defined in the dump file and statistics were not imported.
Action
Check to see if the table and constraint exist. If the table and constraint exist, then report this to Oracle Support Services as an Import internal error.

Pin definition for TV OUT Connector (C&S)

Similar Messages

Maybe you are looking for