Ping problem in the neighborhood and Msan can see the mac address of router
Hi everyone
i have a router 1941/K9 with card EHWIC-4SHDSL-EA ,i have configure this card in my router , the problem is I can not ping the ip @ Neighbourhood and the MSAN can't also see the mac-address of the router do you notice that the interface in the MSAN and in the router is UP / UP
anybody help me
Hi,
An ethernet interface will be always up/up and it goes down only if there is problem between the given port and the connected one. The issue can be anywhere else in the middle.
Similar Messages
-
Can we do MAC Address based routing in ASA5540
I have a network setup where two servers from inside need to communicate with a remote network via 2 VPN gateways. The destinations are same.
However, the chalange is each server need to follow it's own VPN gateway. Since i can't configure PBR (policy based routing) in ASA, can i configure something like MAC Address based routing. I can't use destination based routing since the remote network are reachable from the both VPN Gateways.
Advise needed.
Thanks in advance.
Regards,
R.Siva
Network Security Engineer.Hi
I am not shure i follow you correct here.
You want 2 servers to speak to the same network but over two different vpn units ?
If this is so then this could work
Just set the route to the other network on server 1 to the vpn gate 1
and route the other network from server 2 to the vpngate 2.
in windows the command is route add.
good luck
hth -
I am trying to move my itunes library from my old pc to my new imac, home sharing is on and I can see the shared library. My problem is that when I check the shared library to import it to my imac I cannot import it. Can anyone help me?
You need to transfer the iTunes Library from the most recent backup you made before the hard drive was replaced.
You can't transfer the full iTunes Library from the iPad back to iTunes.
There are third-party Windows applications that will transfer data from an iOS device, but they don't re-create the iTunes Library exactly as it was before. -
I have just bought a Humax 7500T PVR and a Humax W-Lan dongle to connect to my Airport Extreme.
I have put the mac address into the AE. The installation screen on my TV is picking up the network name but once appied it won't connect to the internet.
I've a few other things connected to the AE such as computers, ipad, itouch, etc, and have never had a problem connecting these once I've entered the mac address into the AE. Can anyone help me with this please?have you made sure that the network setting in the system preferences is set up to use dhcp? if not i would try changing it so that it shows that it is getting its address by dhcp
-
hello
The problem appeared two days ago is that I can't open my mail app. everything was fine and functional. Now I double click on the icon and it does not respond. it receives mail and I can see push notifications on the mail icon but when I try to open it is no use. OS Y 10.10.2 (14C1514)Please follow these directions to delete the Mail "sandbox" folder.
Back up all data.
Triple-click anywhere in the line below on this page to select it:
~/Library/Containers/com.apple.mail
Right-click or control-click the highlighted line and select
Services ▹ Reveal
from the contextual menu.* A Finder window should open with a folder named "com.apple.mail" selected. If it does, move the selected folder—not just its contents—to the Desktop. Leave the Finder window open for now.
Restart the computer. Launch Mail and test. If the problem is resolved, you may have to recreate some of your Mail settings. Any custom stationery that you created may be lost. Ask for instructions if you want to preserve that data. You can then delete the folder you moved and close the Finder window.
Caution: If you change any of the contents of the sandbox, but leave the folder itself in place, Mail may crash or not launch at all. Deleting the whole sandbox will cause it to be rebuilt automatically.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return. -
I already downloaded bbm, but the problem some of my friends i can see their profile pictures and there is a problem to invite a contact either barcode and through pin. Did you experience the same problem with mine???
I am sorry but your question is not completely clear. What Apple product are you having problems with?
If English is not your primary language, try posting in your native language.
Best of luck. -
Windows 7-8.1 Can not change the MAC Address on wifi and cannot load login page in public HotSpot.
Windows 7-8.1 Can not change the MAC Address on wifi and cannot load login page in public HotSpot.
Adapter: Ralink RT3070 Chipset wifi adapter
Tested: os Windows 8.1 Professional
Hot Spot: 802.11b
The first problem windows 7-8.1 got IP adress and connect he public HotSpot but cannot load login page or any other page. It does not work with it.
The second problem Wifi canrd/configure/Advandes (No network adress change function).Tested with the default windows driver and the ralink rt 3070 driver the same problem.On windows XP the same function the same driver works perfectly.
multiple users to have expressed interest in the problem But Microsoft not corrected the problem window7-8.1 10?
lizardsystems.com/wiki/change_mac_address/faq/change_mac_address_in_windows_7
blog.technitium.com/2011/05/tmac-issue-with-wireless-network.html
superuser.com/questions/519189/how-to-change-the-mac-address-in-win-8-to-spoof-a-roku-player-through-a-wifi-spl
social.technet.microsoft.com/Forums/windows/en-US/59e07df3-471c-499e-ad5f-e7cb507595df/cannot-change-mac-address-in-windows-7-driver-has-option-doesnt-work-neither-does-regedit-ms?forum=w7itpronetworking
networksteve.com/windows/topic.php/CANNOT_CHANGE_WIRELESS_%28SPOOF%29_MAC_ADDRESS_ON_WINDOWS_7/?TopicId=16810&Posts=1
On windows XP or linux have a MAC adress Change function allow 00 mac adress and another normal mac adress range.On windows 8.1 all Mac changer program dont work.This 2,6,A,E on second adress are not vaild Mac adress. You simply can not use normal MAC
addresses on windows 8.1.When i connect the usb the Pc windows 8.1 recognizes the adapter but the default driver and the downloaded ralink driver the same problem.On windows xp the current driver works perfectly have (Local Mac Network Adress) funktion
and works with the 802.11b hot spot.I got the internet my PC and laptop too public HotSpots and another wifi HotSpots if wont work correctly i can not use neither the windows 7,8,8.1 or 10. Many users have expressed interest in the problem more forums.
The 3. problem im tested in virtualbox the windows 7 and 8.1 on 8.1 (on the blue wifi platform) not show correctly the signal strengh. On windows 7 show this correctly.The windows 7-8.1 Configure/advanced the advanced options on Ralink 3070 the default (windows
driver) somehow downgraded function is less than for Xp. Configure/advanced the advanced options (needs to be upgraded in the future) because it does not advance but rather regressed.
Today it is very common these wi-fi technology increasingly used (hotels,Public Hots Spots,Internet coffe,) growing free bublic wifi projects. The wifi funktions on windows need debugging and modernize.The quality of Wi-Fi is now the operating system
is now a thing order which is not good then the operating system is unusable.Hi,
For changing the MAC address for Windows 7 is designed with some limitation, we cannot get over it. Thanks for your understanding.
Under Windows 7, the possible range of spoofed addresses for wireless adapters that can be set is limited. To be used by Windows 7, a spoofed MAC address should have 0 as a least significant bit (unicast) and 1 as a second least significant
bit (locally administered) in the second nibble. Thus possible values for the second nibble are limited to 2, 6, A and E.
In other words
MAC address: “XY-XX-XX-XX-XX-XX” “X” can be anything hexadecimal. The hexadecimal “Y”, written in binary format, is Y: “kmnp”, where “p” is the least significant bit;
p=0 --> unicast;
p=1 --> multicast;
n=0 --> globally assigned MAC;
n=1 --> locally administered;
So, actually MAC can be changed to any combination in which p=0 and n=1;
“Y” can be 2, 6, A or E.
So the possible MAC addresses in Windows 7 for wireless adapters:
X2-XX-XX-XX-XX-XX
X6-XX-XX-XX-XX-XX
XA-XX-XX-XX-XX-XX
XE-XX-XX-XX-XX-XX
For the wifi hotspot issue, please check this blog to see if it can be helpful.
Windows 7 Connectivity Problems in Public Hotspots
http://blogs.technet.com/b/patrickr/archive/2010/07/28/windows-7-connectivity-problems-in-public-hotspots.aspx
Kate Li
TechNet Community Support -
Hay. i change the screen LCD in IPAD 2 3G but i don't know what happen. She was working and every thing it's ok. One time i turn off the ipad and turn on more time, i don't see good in LCD the brightness is to low and i can see any thing!! and i want to know why is happen
Assuming you mean that you performed the repair yourself, it would seem that you either obtained a defective screen or you did some sort of damage when you replaced the screen. You can try asking for assistance on ifixit.com, a site dedicate to those attempting their own repairs, or you can take the iPad to a shop and pay them to try to correct the problem for you. Apple will no longer touch your iPad now that you've attempted your own repairs.
Regards. -
Every time i scroll down in Gmail the page truns trasnparent and i can see my desktop
Windows 7 64 bit, Current Firefox and gmail. Every time i scroll down the page goes transparent and i can see my desktop. If i wait about 5 seconds the transparency goes away but the next time i scroll it comes back. This makes it very hard for me to read what i am trying to look at. I tried turning off the transparency in Win 7 but it did n ot make any diff. While i was typing this very msg if i went past the bottom or edge of the box the letters went transparent as well. Please help i am at a loss as to how to fix this problem.
ok so i am a nub..lol did not relize that 9 was live...lol Thanks and it looks like that prob is fixed.
-
I recently updated my IMac software to the latest version, now i can't see by WD back up drive in time machine. its conected to the firewire port ok and i can see it if i check firewire connections. The drive works ok on an old windows laptop. Any ideas.
leedssparky wrote:
Is it possible that i did this whilst updating the OS software whilst leaving the WD drive connected.
It's a good idea to eject and disconnect external HDs, just in case, but that shouldn't cause a problem.
Why when setting up time capsule, does it only look for WIFI drives through airport.
I think you're confusing Time Machine (the backup software) with a Time Capsule (Apple hardware combining a wireless router and HD). Unless you have a Time Capsule you want to back up to, there's no point to clicking the Set Up Time Capsule button, if that's what you mean:
I've attached the Firewire bus from system profiler, dont understand why i can see it there but not in TM.
There seems to be some sort of problem with the drive, since Disk Utility thinks it's fixed, but immediately the problem returns (per the first sample you posted).
How old is the drive?
If it's within the warranty period, you might want to contact WD or the place you bought it. -
I have rented a movie on apple tv and wish to finish it on my mac book air. When I open iTunes on my mac book air I can not see the movie in iTunes. It is an authorised device and I can see other purchases just. How do I fix it?
Rented movies downloaded to an Apple TV can't be transferred to any other device.
(86941) -
I just purchased two songs to put on my child's Leappad 2 MP3 player and I can see the songs under my music files but cannot save them because they were not downloaded as a MP3 file What can I do?
iTunes: How to convert a song to a different file format
-
I am trying to move a pdf file onto my iPad2, and it says that the device is not connected or has stopped working. But Windows 7 recognizes the device and I can see my pictures. Same thing happens when I try to put music onto the iPad.
When in iTunes on the computer,my our ipadmshould show under devices.
Click on your ipadmunder devices then go to music at top center of the iTunes window, check what you want to sync for music. You need to set it to a folder if I remember which would have your music in it you want synced.
Same with PDF files.....there should be an option for data or even PDF files at the top center area of iTunes when the iPad is clicked under devices.
If your iPad does not show or you cannot click on it under devices which is in the leftane of iTunes, the iPad is not being seen by the computer.
Try unplugging the USB cord from the laptop then give it a few and see if the computer picks it up. -
my mail app on I phone 4s crashes every time when i try to open, and i can see it thru the setting>general. also phone is overheating and spending battery fast. does any one has some answer on this or same issue? what to do did any has same issue? if i do an complete phone restore what will hapend ?
You can call Verizon to replace it or go to an applestore to replace it since it won't even power on with multiple chargers.
-
Aftger I upgraded to Yosemite I cannot see my iMac at home from my work (i.e in Finder window under shared devices). Note both my work and home iMac are connected to time capsules and I can see both of those time capsules but I cannot see either iMac from the other location. My guess is that the time capsule is blocking the connection to the iMac. One last comment occasionally (5% of the time) my iMac does magically appear in the shared Finder window but this is extremely rare. Any help????
Just discovered this one myself. OK, this may sound silly but place your cursor next to the word "Shared" on the finder sidebar. The "hidden" command "Show" will magically appear. Clicking that will display your other network attached devices.
This appears to be a new "feature" that some freaking genius thought was some how "Cool". My only assumption is that Apple programers expect users to randomly move their cursor around the screen in hopes of finding some critical function like looking for an easter egg in their favorite game.
Maybe you are looking for
-
Best practice for iTunes' music folder
i keep my music on an external drive, but want itunes to be able to play the songs. currently, the itunes music folder is set to its default location. i changed the preference to prevent iTunes from copying music to this location. i added music to iT
-
Find & Replace window missing in Toolkit CS5
Hello-- I just started using Adobe ExtendScript Toolkit CS5 after installing Photoshop CS5, and ran into a strange problem: the Find & Replace menu option and key command do not function correctly, in that I cannot access Find at all. The Find / Fin
-
VB CS4 - How send many textframe to a document to fill page and then another
Hi, Sorry by my bad english, I'm using CS4 and vbscript. Need to take information from several fields in a database and send it to an Indesign document. Progressively fill a page and then another. How do you add a textframe automatically for each fie
-
Base table for customer in R12
Hi, What is the name of base table for customer in R12? Thanks, GSM
-
Constants: "final static" vs. "final"
In a GUI object, I have some class constants that are only used internally. Example 1: private final int PREFERRED_WIDTH = MainWin.MAX_WINDOW_WIDTH; private final int PREFERRED_HEIGHT = 50;Example 2: private final JButton helpButton = new JButton("He