Pink noise in audigy 2 zs video editor!!!

Hello! I'm italian so sorry for my bad english!...
Yesterday i've bought a audigy 2 zs video editor for my work... i've installed drivers and software (updated on creative page)... i was ready to capture video and audio, BUT after capturing the file has audio problems...
I can see video (good quality), but the audio track was corrupted... you can hear only a noise... like pink noise (the noise used to test P.A. audio system)!!!
WHY??
My Pc configuration is this:
AMD 64 3400+
Gb Ram
2 hd 250 Gb
Ati Radeon X700

LpGroove,
Take a look at the Movie Creation Guide (in your product and also at: http://www.soundblaster.com/products...ationGuide.pdf) chapter 7, and page 7-6 in particular. Make sure your audio source is connected to the correct audio inputs (near the video inputs) and the Creative Mixer settings are correct.
-Chris

Similar Messages

  • Audigy 2 Video Editor - Inspire 5.1 Digital 5

    How could I have sound with my Inspire 5. Digital 5700 with the digital DIN connector using a Audigy 2 ZS Video Editor Card ?
    I have sound on 2 channels with the optical and/or coaxial cables, but I want to have the 5 channels thrue the DIN cable. Where must I put the connectors and how must I configure the parameters in my computer ?
    I have the DIN-DIN connector and the DIN-Jack adaptator.
    Thank you in advance for you answer.
    Malou.

    Daedalus3,
    I know I've addressed this one before ... I have never heard of any Audigy soundcard, including Video Editor, taking a 5. compressed signal into the S/PDIF and recording it as a *.ac3 (for example). I do not know of commercial audio software apps that support this and anyway there would be an outcry from the RIAA because such a facility would remove all "roadbumps" to jacking commercial surround recordings at full resolution.
    You can record a stereo uncompressed stream from the SPDIF (e.g. the output of a DAT player or of various other consumer audio devices).
    -Chris

  • Vista Drivers for the Audigy 2ZS Video Editor

    OK, so I know I'm only one of 20 people in the world who were ever stupid enough to buy one; but I am disappointed to see that there is so far no Vista beta driver support for the device.
    Are there plans to ever support it under Vista?
    As half of the internals are an Audigy 2ZS sound card for which Creative are developing Vista drivers, the job is surely half done? Modifying the existing USB video capture driver surely can't be too difficult?
    Must say, that if this device is ignored under Vista, it will be the last Creative product I ever buy .....
    Nigel

    I wish someone from Creative would give a definiti've answer to this question.
    I've had the Video Editor for about a year so it's hardly old technology, and Vista was in development last Summer. The Audigy ZS sound drivers are being developed for Vista, how diffcult can it be to get the Video drivers modified to run under Vista?
    Nigel

  • Audigy 2 Video Editor Sound Issue

    The sound is great, but for some reason every once in a while i get this problem and i cant figure out why... I plugged in my headphones to the soundcard so i dont disturb my parents yesterday and when i took it out the sound wont come out of my speakers anymore. I can only hear sound through my headphones. I rmember I did something in the past and i got it working again through the speakers but I can't remember. Can anyone please help because I'm getting annoyed that I have to listen through my headphones now. Thanks

    I also had this problem today. Did anyone ever find a solution?

  • Creative audigy 2 zs video editor probl

    please help how could u adjust the frame size and the video bit rate of audigy 2 video editor before capturing
    it seems that the video bit rate and frame size remains fixed cannot adjusted
    why is it audigy 2 ve is recognized as unknown msdv at the source of ulead video studio?
    please help
    regards
    dan

    Thank you for the reply split0,
    as for the informati've post, thank you for the compliment, i tend to not open a thread at all unless i have spent enough time on the problem and searched around enough for solutions, and after that i only post if it has enough info regarding everything in inside the thread.
    In regard to the known incompatibility list, unfortunatly this is one of the things i checked beforehand already.
    The PCMCIA adapter in my laptop is a Texas Instruments PCI-8x2/7x2/6x2 CardBus-controller.
    Which is one of the most common controllers and should normally not cause any troubles at all, also in another thread on this forum i found a differant driver for it, i even tried that with no result sadly.
    At the moment personally i am thinking the whole problem lies within not being able to uninstall the onboard sound card to full extent somehow, and while i posted here i also have all this info in a direct message sent to creative, and even acer for that matter.
    In hopes of some kind of solution for this so i can keep my hopes up for not having to return the card itself.
    What bugs me is that there is option at all to disable the onboard sound through the bios.
    Because right now whenever i install the ZS notebook card it checks hardware for the onboard first installing it again, then setting priority for the zs notebook.
    This is what seems to result in the crashes through a conflict in drivers in my idea, but thats just a hunch which i cant do anything about currently in regard to testing unless someone has an idea for me to try.
    Message Edited by Natharneal on 05-23-2008 0:54 PM

  • Audigy 2 ZS Video Editor -5.1 input via SPD

    <SPAN>
    <SPAN>
    <IMG height= alt="" src="http://forums.creative.com/i/p.gif" width= border=0>Ok, I'm a little frustrated now but I'm sure and hope this is my fault and not the one of the device. I bought an Audigy 2 NX which isn't able to capture and encode 5. audio streams. Now I bought the Audigy 2 Video Editior and it doesn't seem to capture 5. either. I have a digital cable receiver connected to the SPDIF input of Audigy and have the receiver set to play a 5. Dolby Digital stream. However, all Audigy 2 does is playing a crackling sound.All encoders at the Device Management are enabled. Doesn't the Audigy 2 Video Editor support 5. input streams?

    Daedalus3,
    I know I've addressed this one before ... I have never heard of any Audigy soundcard, including Video Editor, taking a 5. compressed signal into the S/PDIF and recording it as a *.ac3 (for example). I do not know of commercial audio software apps that support this and anyway there would be an outcry from the RIAA because such a facility would remove all "roadbumps" to jacking commercial surround recordings at full resolution.
    You can record a stereo uncompressed stream from the SPDIF (e.g. the output of a DAT player or of various other consumer audio devices).
    -Chris

  • Audigy 2 Zs "video" editor ??

    Hi. Will there in nearby future be developed a driver suit for the Audigy 2 video editor for vista, or perhaps a driver for the video portion of the unit, so?that I?can get to use the unit for primary reason why the product was purchased.

    Some tips from another user:
    I have used the follwoing procedure to install a working configuration of the Audigy 2 ZS Video Editor in a clean install of Vista Ultimate.
    () Download from Creative Labs (US) site: http://us.creative.com/support/downloads/ the following files:
    (a) Creative Sound Blaster USB Series Windows Vista Driver .00.0060 - USBVS_PCDRV_LB__00_0060.exe (from the Vista section)
    (b) VidCap for Creative Sound Blaster Audigy 2 ZS Video Editor .00.000 - A2VX_PCVDE_L9__00_000.exe (from the WinXP section)
    (2) Use WinZip or WinRAR to open the file (b) and extract the folders \DrvInst and \Vidcap into your Vista Downloads folder.
    (3) Connect the Video Editor to the power supply and a video source; connect the USB cable to your PC. Ignore the "Found NEw Hardware" dialog that pops up.
    (4) Doubleclick on file (a) to install the Creative Sound Blaster USB Series Windows Vista Driver, and follow prompts as required; accept all defaults. After install is complete, let the PC reboot.
    (5) After rebooting, in the "Found New Hardware" dialog that appears, select the options to search for a driver, don't go online to search, browse for a driver and point the search at the \DrvInst folder you extracted in (2) above. The USB video driver will be installed from the \DrvInst\Video\Driver\Win2k.
    (6) After the video driver is installed, doubleclick on the Setup.exe file in the \Vidcap folder you extracted in (2) above to install the Vidcap application.
    (7) Setup the options in Vidcap, and run a test recording.
    Happy capturing under Vista.

  • Acer Laptop with Video Editor No so

    Hello,
    I have the ACER TravelMate 4654LMi NoteBook and the SoundBlaster Audigy 2 Video Editor.
    I connect everything but I could not see the image of the Notebook on the Sony Wega TV (s-vhs connected).
    It is also connected with the home theatre Sony but I can't hear anything.
    May be I am doing something wrong but I don know.
    Can I play a Game in the Notebook, and Wath it on the TV as a I Hear the Sound on the Home Theatre Speakers? How should I install it !! Please help me !!!
    Thank you
    mickeith

    That's exactly what I was going to suggest.  I'd try it again after a Windows Update (over and over if necessary) and a reboot.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Some one help me pls on Audigy 2 ZS Video Editor

    dear all,
    can some one tell me that can i use dvd player video in to the Audigy 2 ZS Video Editor and the output of surround audio in my preamp with 5.1 speakers without using computer.
    can i use the Audigy 2 ZS Video Editor as a external av receiver for my digital tv and preamp and digital speakers.

    nelson007 wrote:
    dear all,
    can some one tell me that can i use dvd player video in to the Audigy 2 ZS Video Editor and the output of surround audio in my preamp with 5.1 speakers without using computer.
    can i use the Audigy 2 ZS Video Editor as a external av receiver for my digital tv and preamp and digital speakers.
    Never tried it but I guess it should work.

  • Audigy 2 ZS Video Editor - recording audio from optical digital in - sound drops

    Hi guys
    I've had an audigy 2 zs video editor for a couple of months now and it's greatly improved my audio output from my computer.
    But the other day I started trying to record vinyl onto my computer directly.
    In the past I've always used my hifi cd recorder deck, then ripped the audio off the cd.
    So I have my turntable connected to my amp, and I use my minidisc deck as a DAC, then record using an optical from my minidisc DAC, to the optical input on the front of the audigy.
    So I fire up the creative smart recorder software and start messing with the levels.
    I also use a free bit of software from
    http://www.darkwood.demon.co.uk/PC/meter.html
    called meterV which gives me a larger and more prominent read out of the level.
    I then fine tune the output level on my DAC.
    I have the stereo line out sockets on my audigy connected to an input on my hifi amplifier for listening to digital music etc.
    So I start the vinyl and the sound starts coming through my DAC into my soundcard, the level readings start going, and the sound comes out of my hifi speakers.
    My amp's switched to the audigy input - not the turntable
    The problem is... every 30 seconds or so, the sound cuts out for 2-3 seconds and then resumes.
    But the sound doesn't drop off on the level meters, or on the actual recording (recording 44.khz, 6bit wav file).
    Only on the stereo line out of the audigy.
    I ran the following test to see if the sound also cut out on the optical and coax outputs...
    Whilst recording from the optical input, I've also tried recording to a minidisc portable from the optical out at the same time.
    And the sound cuts out the same as when listening to the stereo line outs.
    So the sound cuts off on the line out, the optical out, and also the coax out.
    But this only happens when recording from the optical input.
    When recording from the stereo line in - the sound doesn't cut out on any output!!!
    The input selected in creative smart recorder is SPDIF.
    This problem happens when smart recorder isn't even running - if I'm just listening to the line outs the sound cuts out.
    But if I'm just playing back an MP3 or any sound, and there's nothing coming into the inputs, then playback is fine!!
    So it's not a connection issue!
    It doesn't seem to be triggered by sound frequencies - it seems to happen every 30-40 seconds no matter what is being recorded (it does the same thing when playing a CD so it's not just when using a turntable)
    I've tried restarting the computer several times.
    All the connections are properly seated.
    I've had task manager loaded whilst this is happening to check CPU usage, and nothing - it just continues in a fairly straight line as normal. No spikes in CPU usage (I would have thought it unlikely that the video editor would be affected by such things anyway being an external box).
    There is nothing else connected to USB - other than an internal memory card reader attached to a motherboard USB header.
    And a wireless adaptor also connected to the motherboard - but the problem still happens when the wireless adaptor is disabled.
    There's also nothing else connected to the USB ports on the Video Editor box.
    Machine spec:
    Shuttle SN4G2-v3
    AMD Athlon XP 3000+
    GB memory
    80GB IDE HDD, 2 x external Lacie FireWire 250GB dri'ves
    LG dual layer dvd/rw/ram
    Win XP Pro SP2
    I've not upgraded firmware or drivers - just used the installation from the CD.
    What confuses me is why this only happens when recording from the optical input, and it affects all outputs but the recording and the level monitor show no trace of the temporary loss in sound!
    So the audigy is receiving the sound, but it just drops off the outputs for some reason!
    Any ideas?
    I hope the above explanation is clear.
    Thanks
    Ben

    batfastad wrote:
    Sorry for not replying - have been away for the past few days.
    Ok, so I go to Creative Device Control, and on the PCI/USB tab I've changed the sampling rate to 48khz.
    It was previously at 44.kHz
    The bit depth is still at 6bit
    Now the problem seems to be solved.
    The problem was only with the output from the device. And now there are no skips!!
    Excellent!
    Why has that solved it though?
    I've read on other forums (head-fi) that the audigy cards do not run at 44.kHz nati'vely so the sound has to be downsampled.
    Is that skipping an artefact of that downsampling process?
    Will having that set at 48kHz, but recording to a 44.kHz 6bit wav file theoretically reduce the quality of the recording - compared to having it set at 44.kHz and recording a wav at 44.kHz?
    On the SPDIF tab the input sample rate is shown as 44.kHz - as that's what is output by the DAC in my minidisc deck.
    But when I changed the sampling rate on the PCI/USB tab, the SPDIF output sampling rate also changed to 48kHz.
    This means if I wanted to record from the optical output, whilst also recording to the computer, and that device only supported 44.kHz - I can't do that?
    You listed some main reasons to the truth, why Creative SB cards are not very popular on serious use (DAW). I.e. need for resampling. X-Fi's in creation mode are (least said to be) the only ones not resample everything.
    There is a setting for "Bit-Accurate-Recording" (digital modes only) --> have you tried if that works on your recordings?
    jutapa

  • Trouble using Creative Audigy 2 ZS Video editor with an external Dolby / DTS Deco

    I had purchased a Creative Audigy 2 ZS Video editor for following two requirements,
    I wanted to be able to Digitize video from almost any source.<
    And I also wanted to have an external Audio Card that I could share between my Home Desktop / Laptop and let Digital Audio Signal get to my Yamaha Reciever that powers a Bose Home Theater Speaker System.<
    My typical connection setup is,
    Desktop / Laptop >> USB 2.0 Shielded Cable >> Audigy 2 ZS Video Editor >> Optical Out >> LC Optical Cable >> DVD Optical In of Yamaha reciever
    I do not have WinDVD or any other program that can allow SPDIF in Pass Through Mode, so I use VLC as my media player. While playing DVD / other DivX / XVid videos with Dolby / DTS / AC3 audio track I get the option of setting the audio to SPDIF Pass through Mode and that's how I use it.
    It had been working fine for a while (6 months) and then I was not using the card for a while (been busy at work). And since then I'm not able to use this in SPDIF Pass Through Mode any more.
    Each time I select that mode in VLC the player kinda freezes and plays Media File with breaks, making it just un-usable. In case I leave the player audio option to Stereo output?mode it works fine, but I do get only Analogue Audio deli'vered to the External Recei'ver and to say the least, after listening to DTS / Dolby audio this simply doesn't cut it.
    I've already updated the latest drivers from Creative Site, have tried the card with two different Dell Laptops (D820 and D80) and my home desktop. It gives exactly same result in all cases.
    I've not tested DTS Decoding output from the Device itself, 'cause I don't have sufficient cables to take decoded output from the device and send that to the receiver. But in case I opt that option in VLC player The player keeps playing Video without any issues. I can't validate if it's decoding correctly or not, 'cause I don't have cables to connect all that outputs to the receiver.
    Can my problem be related to anything on the Optical connection cable itself?
    If someone could shade some light on this issue that would be really helpful.

    Hello,
    I have the exact same problem and would very much like to know if there are 64bit drivers available.
    Thanks in advance.

  • Creative Sound Blaster Audigy 2 ZS Video Editor

    Creative Sound Blaster Audigy? 2 ZS Video Editorc Hello.
    I've recently changed from WinXP Pro SP3 x86 to Win7 Ultimate x64.
    After installing the only available driver [Beta .0.0098] and rebooting, the Device Manager still lists an Unknown Device which corresponds to the video part.
    <img border="0"><a rel="nofollow" target="_blank" href="http://img38.imageshack.us/img38/8/videoeditorprob.jpg"]http://img38.imageshack.us/img38/8/videoeditorprob.jpg[/url]
    In Windows XP there were always two devices listed:
    - SB Audigy 2 ZS Video Editor Audio Device;
    - SB Audigy 2 ZS Video Editor Video Device.
    I've tried to do the steps mentioned here <a rel="nofollow" target="_blank" href="http://forums.creative.com/t5/Windows-Vista/WILL-YOU-SUPPORT-THE-AUDIGY-2-ZS-VIDEO-EDITOR-IN-VISTA/m-p/3602"]http://forums.creative.com/t5/Windows-Vista/WILL-YOU-SUPPORT-THE-AUDIGY-2-ZS-VIDEO-EDITOR-IN-VISTA/m-p/3602[/url] with both old and more recent XP/Vista 32/64 drivers and I still can't get the device installed and VidCap properly running.
    Thanks in advance.

    Hello,
    I have the exact same problem and would very much like to know if there are 64bit drivers available.
    Thanks in advance.

  • Using Audigy 2 ZS Video Editor without compu

    Hi
    I've got the Audigy 2 ZS Video Editor and, as my front room decoder has just gone kaput, I'd like to use it as a decoder without having to have it plugged into my computer. However, I've run an optical cable from my DVD player to the A2 ZS VE and connected it to my 5. speakers - but no sound comes out. Do I give up here?
    Ta
    Neil

    Anyone know whether this is possible?
    I'd love to be able to re-write the functionality of the supplied remote control.
    Any chance of you guys at Creative releasing a small app which anyone could use to trigger a custom command on any remote control action?
    Thanks
    Ben

  • Audigy 2 ZS Video Editor & Vista Business installation iss

    So this is my letter to?Creative who have yet to respond, does anyone have a similar set up to me who can shed some light on this issue and fixing it. Having no sound and not being able to listen to itunes is not a good thing.
    To Engineers,
    Firstly id like to say I?m very disappointed in purchasing this $400 AUS SB Audigy 2 after looking on your website and seeing the Microsoft vista logo plastered everywhere thinking this device would be compatible, quite clearly it is not as I have installed/uninstalled drivers and disks..only to find that it is pointless..
    So here I am about to explain my situation in order for you guys to find me a suitable driver ASAP.
    I currently have a HP M777A running on Microsoft Vista Business with 3.06GHz and 2x GB Kingston Memory..
    In my office I have a 5. speaker surround which sits with my 9?LCD which I like to listen to music from and watch DVD?s.
    In my lounge room I have a 42? LG Plasma Display which also runs with my Denon AV4306 Recei'ver which also have a 5x speakers surround.
    Prior to Vista, I was able to watch DVD?s or listen to music through iTunes which was being powered through my PC, I was able to do this simultaneously in both rooms. This is what I need to achieve again very soon.
    After scouring dozens of websites and reading this products pitch lines which states that this virtually anything can be played through it, well this is why I bought it.. But I?m very disappointed.
    My question to you guys is this.
    . Is there a driver or something I can load up to fix my problem
    2. ?If NOT, then how long will it take to be released.
    3. ?If so, how do I find out about it when it is released.
    4. Etc etc.
    Please advise ASAP with a solution I can work with.

    Copied from the Video forum - (related to video operation under Vista)
    I have used the follwoing procedure to install a working configuration of the Audigy 2 ZS Video Editor in a clean install of Vista Ultimate.
    () Download from Creative Labs (US) site: http://us.creative.com/support/downloads/ the following files:
    (a) Creative Sound Blaster USB Series Windows Vista Driver .00.0060 - USBVS_PCDRV_LB__00_0060.exe (from the Vista section)
    (b) VidCap for Creative Sound Blaster Audigy 2 ZS Video Editor .00.000 - A2VX_PCVDE_L9__00_000.exe (from the WinXP section)
    (2) Use WinZip or WinRAR to open the file (b) and extract the folders \DrvInst and \Vidcap into your Vista Downloads folder.
    (3) Connect the Video Editor to the power supply and a video source; connect the USB cable to your PC. Ignore the "Found NEw Hardware" dialog that pops up.
    (4) Doubleclick on file (a) to install the Creative Sound Blaster USB Series Windows Vista Driver, and follow prompts as required; accept all defaults. After install is complete, let the PC reboot.
    (5) After rebooting, in the "Found New Hardware" dialog that appears, select the options to search for a driver, don't go online to search, browse for a driver and point the search at the \DrvInst folder you extracted in (2) above. The USB video driver will be installed from the \DrvInst\Video\Driver\Win2k.
    (6) After the video driver is installed, doubleclick on the Setup.exe file in the \Vidcap folder you extracted in (2) above to install the Vidcap application.
    (7) Setup the options in Vidcap, and run a test recording.
    Happy capturing under Vista.Message Edited by Dale-CL on 04-8-2007 :3 AM

Maybe you are looking for