Pio 110D on the way....question regarding firmware

I finally pull the trigger and ordered a Pioneer 110D from OWC (along with 2GB ram, too!). Obviously I won't know what firmware it has until I get it hooked up, but I wanted to be prepared to upgrade it in the meantime.
I found the DVRFlash utility, but can only seem to locate a firmware updater for WIndows with the lastest 1.39 firmware. I have access to a PC that I could put the drive in to flash if needed, but I'm not sure this would be the best option. If I can't find that firware for DVRFlash, it's my only option, though!!
Anyone give me pointers on this or thoughts? Thanks.

The firware that's listed for Windows on Pioneer's site is the one you want. They label it as Windows since the download contains the firmware files (two of them) and a Windows-only program to perform the flash. Because the flash program Pioneer provides is Windows-only, that's why we have to resort to using the DVRFlash utility.
When you download the .exe file from Pioneer, you'll probably have to use Stuffit Expander to decompress the file. You'll end up with a folder that contains the three files mentioned above. Move the two firmware files (They probably end in .139 or something) into the same folder as the DVRFlash executable. Then, just follow the instructions that came with DVRFlash and you should be good to go.
Make sure you're using DVRFlash version 2.2. The GUI version, DVRFlashX, is only at version 2.1 and doesn't support the DVR-110D.
The 1.39 firmware must only be a few days old. I had looked last week and it was still at 1.37.
Hope this helps.

Similar Messages

Question regarding firmware reset and provide the Hash to the advisor assisting you.

Hash: C0224060G9GF1YM1H45B4D010997AAEBE

This is not Apple Support, and no one here knows anything about your contact with Apple.

I was given a task to find out more information on the following before we purchased anything. Please, can you answer the following questions regarding the IEEE 488 to Ethernet.

1) How do we connect our network analyzers to the network?
2) What do we need to purchase?
3) How much is this going to cost us?
4) What kind of capabilities will this give us? (if any)

I think you are talking about the GPIB-ENE from NI.
1) You have to setup the ENET box by giving it an IP address. You may also need your Sys Admins help to do this. After that you will need to install the software, connect to the ethernet and connect to the equipment.
2) GPIB-ENET/100 from NI. Not sure if the NI488.2 comes with it or seperately, but you need it also.
3) Between $1,000 and $1,500 (US)
4) I like this solution. It allows you to control IEEE 488
equipment from virtually anywhere. You do not have to have a GPIB controller on every PC, but only on the equipment to control. I have test stations that I roll from place to place. I don't have to worry about connecting the station to a PC. I simply plug the station into the LAN and use any PC I want.
If you have e
quipment that you would like to control from anywhere or move from place to place this is the only way to go.
Kevin

Answer the following question regarding GUI_UPLOAD and Open Data Set

1. whats the connection or relationship of S_GUI to GUI_UPLOAD?
2. GUI_UPLOAD saves files to local directory of a use while OPEN DATA SET saves/archives files in the server directory. Where is the risk directed towards consuming disk space? Server disk or workstation disk space?
3. how will this work for multiple files?
4. Regarding Open Data Set - How the files will be put in AL11?

The GUI_DOWNLOAD only download the file to local PC...so any abap code running in other pc will not able to use the file.
BUt if you use open dataset to load the file APPLICATION server any ABAP pogram can access the file.
Following code explains how you load file using open data setto appl server,
you can check in t-code AL11 for files/dir in applicatin server.
you to change the value of myfile variable in my code..
you have to give the full path of the dirctory.
plz reward points if it hlps you.
Report ZANID_TEST2 message-id ZM.
data begin of itab occurs 0. "your internal table
include structure MARA.
data end of itab.
*--file upload purpose--
DATA: BEGIN OF it_file OCCURS 0,
buffer(200),
END OF it_file.
DATA: myfile(128) type c value 'E:\usr\sap\put\sample1xx.txt',
start-of-selection.
*--populating itab--
select * from mara into corresponding fields of table itab
up to 100 rows.
perform UPLOAD_FILE_TO_APPL.
*--form definitin--
form UPLOAD_FILE_TO_APPL.
OPEN DATASET myfile FOR OUTPUT IN TEXT MODE.
IF sy-subrc NE 0.
MESSAGE e999(zm) WITH 'File could not be opened'.
ENDIF.
*-- creating the file data table
loop at itab.
*-- i am only taking two fields
concatenate itab-matnr itab-matkl into it_file-buffer
separated by space.
append it_file.
endloop.
LOOP AT it_file.
TRANSFER it_file-buffer TO myfile.
CLEAR IT_FILE-BUFFER.
ENDLOOP.
CLOSE DATASET myfile.
IF sy-subrc NE 0.
MESSAGE e999(zm) WITH 'File could not be closed'.
ENDIF.
endform. " DUPLOAD_FILE_TO_APPL

Change the way questions are submitted!#!$!#$!# -- QUEST - VIDEOS IN DOCK

First of all, you've got to change the fact that you can only post a question under a new forum. It took me 20 minutes of frustration to figure that out. It's not intuitive and should be changed!!#$!#$!#$!#$!#$
My problem is that I bought an home stereo system with an iPod dock. I'm using a brand new iPod Touch. I'm trying to watch downloaded exercised videos in my exercise room on the iPod Touch hooked up to my new stereo system. The problem is that when I place the iPod Touch in the dock and play the videos, the videos are shown horizonatally, not vertically. I'm trying to watch videos with the iPod Touch in the Dock. How do I fix it so I can watch them vertically

Can't help with your video issue, but I'm not sure what you mean by "can only post a question under a new forum". At the top of each forum is a link just below the forum title that is called "Post a new topic". That's the link you're looking for. Not sure what route you had to take.

Question regarding Polling data from database using DB Adapters in BPEL

Hi,
I have the following question regarding Polling data from database using DB Adapters in BPEL -
If I am selecting data from multiple tables/view to ultimately generate hierarchical xml document, is there a way that I specify polling all of these tables/views. Is polling limited only to one table/view?
Thanks
Ravi

Hi Ravi,
your question seems to have been answered for the question of polling a set of tables with one as the root, and getting back a hierarchical xml representing multiple related tables.
However you can also poll for changes to both the root table and its related tables. Not sure if this was your question or the one already answered. If the former please check out the sample
bpel/samples/tutorials/122.DBAdapter/advanced/polling/PollingForChildUpdates
Thanks
Steve

Questions regarding Adobe Interactive Forms capabilities

Hi,
We have the following questions regarding Adobe Interactive Forms.
1. Not able to create a text field with dynamic size according to the data entered in the text field in a form with Static Content type forms.   We use a scroll area, but cannot print content that is not visible in the scroll area.
    We currently have Designer 7.0 and 2004 SP 16. I tried to set Form Properties -> PDF Render Format to be Acrobat 7.0 Compatible Dynamic PDF but the text field did not grow dynamically.
2. Another requirement is that once one form is accepted by the Customer, we need to generate a second, new form (with all user entered information from the first form) and the customer should be able to print the form.
    To implement this, we need to have a form that can support dynamically growing text field in some areas, and specific positioning of form elements for other areas. Can we have a dynamic form which lets the fields grow dynamically according to the data entered in the field and with specific positioning of elements?
3. Sending emails from Offline forms Requirement is to send an email as soon as the form is accepted by our Customers. But the Customers can complete the form offline. Is it possible to automatically send an email in an offline forms without having the user push the send button from their email application? Can the Adobe Form do that part automatically?
Appreciate any help regarding above questions.
Thanks,
Kalyan

HI Francois,
Thank you very much for the very helpful information.
1. I am able to insert now the floating field inside a static text but the text does not grow dynamically even when I set the form type to be "Flowed Content". Is it something that required Adobe Designer 7.0 and also 2004s ADS?
2. I can still select only Flow or position content from the option but how can we use both in the same form? I am using Adobe Designer 7.0 and it allows to select only one. Is it again a problem in lower versions that I use?
3. This is an excellent idea and I strongly believe this is going to work (am trying to create POC for this solution). The form should be able to call the webservice as long as the user is connected to internet.
Can you provide your views on the first two points. I appreciate your help.
Thanks,
Kalyan

Question regarding mic plugged into audio in/optical digital audio in port

So I have this external headset... headphone/mic set combo... I plug the headphone jack in the headphone slot and the mic jack in the audio in/optical digital audio in port slot in the back of my IMAC. I go to my system preferences select "sound" and "line in - Audio line in port". But when recording, it's still recording from the internal mic? How do I just record just from the external mic??? What am I doing wrong? I've read all the other questions regarding how to get the external mics to work, but it's still recording from the internal mic? Help?
Mac OS X (10.4.9)

I never expected APPLE wouldn't make a mac that didn't have a proper mic jack?
It has a proper one, a good one, a professional one, not the toy that comes with most PCs. Apple has used line level analog audio input for years.
From Wikipedia;Line level is a term used to denote the strength of an audio signal used to transmit analog sound information between audio components such as CD and DVD players, TVs, audio amplifiers, and mixing consoles.
In contrast to line level, there are weaker audio signals, such as those from microphones and instrument pickups, and stronger signals, such as those used to drive headphones and loudspeakers. The strength of the various signals does not necessarily correlate with the output voltage of a device; it also depends on the source's output impedance, or the amount of current available to drive different loads.

Questions regarding DTP

Hello Experts
I am trying to load data from ODS to a Cube and have the following questions regarding DTP behaviour.
1) I have set the extratcion mode of the DTP to delta as I understand that it behaves like init with data transfer for the first time. However, it fetches the records only from the change log of the ODS. Then what about all the records that are in the active table. If it cannot fetch all the records from the active table then how can we term it as init with data transfer.
2) Do I need to have to seperate DTPs - One for full load to fetch all the data from the active table and another to fetch deltas from the change log.
Thanks,
Rishi

1. When you choose the Delta as Extraction mode you get the data from only change log table.
Change log table will contain all the records.
Suppose when you run a load to DSO which contains 10 records and activate it. Now those 10 records would be available in Active table as well as Change log.
Now in the Second load you have 1 new record and 1 changed record. When you activate, your active table will have 11 records. The change log will have before and after image records for the changed record along with 11 record.
So The cube needs that images, so that data can't be mismatched with old data.
2.If you run the full load to Cube from DSO you need to delete the old request after the load. which is not necessary in the previous case.
In Bi 7.0 when you choose full load extraction mode you will have flexibility to load the data either from " Active Table or Change log table".
Thanks
Sreekanth S

Questions regarding using the .monitor command to retur a animated image and we would like feedback to a designed webpage that is monitoring a 5kW windturbine:)

I'm embedding a front panel image in an existing HTML dokument. I would like to use the command .monitor in the URL together with the refresh command so the VI automatic will reload every 20 secund. This actual work, but simultaneous I want to have the possibility to refresh manually so I don't have to wait 20 sec before new values is shown in the display. Is this possible to do?
Another question: Since the real time display updates 1-2 times a secund the command .monitor is used to get a animated picture of the Real Time Display.
There are several ways to add animation on to web pages. The techniques used h
ere are the �server push� and �client pull�which makes the browser repeatedly reloads a changing inline image to provide crude animated sequences. This is not the most efficient way as this result�s in an image being re-transmitted for each frame of the animation. The command .monitor with the attribute refresh and lifespan in the URL trigger this �server push� and �client pull� techniques.
I use this automatic refresh uploading of the display so that it each time shows different values, is this called crude animation?Then I'm wondering what I'm suppose to use the command lifespan to?I can't see the use of it in my display.....?
link to the webpage so you can have a look at the display:
http://134.7.139.176/.monitor?Real%20Time%20Performance.vi&refresh=20
This is a project that I'm working together with another Norwegian friend. WE are very happy for feedback on our web page and displays go to: http://www.ece.curtin.edu.au/~peersena/ if you would like to view itThanks

Annis,
One of the other things to keep in mind is that the generation of an image does take some computing power so having the generation and the acquistion on the same machine is not always ideal. If you're using the machine that is publishing the front panel just to collect data it's not so much of an issue.
If you really want to monitor in "Real-Time" using Remote Panels (requies LabVIEW 6.1) is your best option. This posting has more information on using Remote Panels and links to some live examples:
http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=506500000008000000C0660000&UCATEGORY_0=_49_%24_6_&UCATEGORY_S=0&USEARCHCONTEXT_TIER_0=0&USEARCHCONTEXT_TIER_S=0&USEARCHCONTEXT_QUESTION_0=web+control&USEARCHCONTEXT_QUESTION_S=0
Remote panels makes it possible to control the application remotely as well.
With .monitor the only way I've been able to manually refresh is to "Shift+Refresh" on the browser.
Regards,
Kamran

Reading the older questions, is there a way in which the full screen slide shows can be saved and/or exported?

Reading the older questions, is there a way in which a full screen slide show (such as places or geotagged photo's) can be saved and/or exported for viewing by another party?

Yes. Just export the slideshow and select your preferred output size.
Regards
TD

Question regarding the Transformation activity in BPEL

Hi,
I have a question regarding the Transformation activity in BPEL.
I have a database adapter that uses a PL/SQL API. The API returns two tables of nested objects and it automatically generates a schema for me based on the outputs structure. I need to use the Transformation activity to map both these out parameters to root element in the destination.
The element in the destination is "unbounded". Please take a look at the following screen shot -
http://www-apps.us.oracle.com:1100/~rvishnuv/transform1.gif
From the screen shot, you can notice that I have two XML segments X_TEST_TBL and X_TEST_TBL1 in the source and I have one GLOGXMLElement ("unbounded") in the destination. I need to map each of the source elements to the same destination. Then internally, I will be mapping the elements of X_TEST_TBL to "Location" segment/element and the elements of "X_TEST_TBL1" to "ItemMaster" segment/element. If I try to use "foreach" and map second
element "X_TEST_TBL1" also GLOGXMLElement using the foreach, I get the following error -
http://www-apps.us.oracle.com:1100/~rvishnuv/transform1_error.gif
Let us say my X_TEST_TBL contians two records and X_TEST_TBL1 contains one record. Is there any way that I can use these two out parameters to map to the same destination (GLOGXMLElement) so that my final document contains multiple "GLOGXMLElement"s that represents data from both the output parameters? i.e. there should be in total of three occurances of GLOGXMLelement in the output document such that two occurances correspond to data obtained from X_TEST_TBL and one corresponds to data from X_TEST_TBL1.
Please let me know if there is any way to achieve this.
Thanks
Ravi

Is the listed $200 credit towards a trade-in on top of the original trade in value of a phone, or the maximum amount?

I got a question regarding the hard disk.

I got the following Question. I have the new 10.7.1 software, and of course two partitions, BOOTCAMP and Macintosh HD.
And the problem is that in BOOTCAMP are the folders : Application, Library, System, User. And if I put some music in iTunes the music of course will be copied into User/.../iTunes etc... and u can imagine that the partition BOOTCAMP is only a 20GB partition, so that soon the partition will be full. How can I solve the Problem, to move the folders Application and User in the Macintosh HD, when i try to do it okay...but i can't delete from Bootcamp, it says “Applications” can’t be modified or deleted because it’s required by Mac OS X.
regards Raphael S.

Why do you have this 20GB?
Back it up.
Remove it.
Extend the Mac Extended volume.
Restore files.
If you have set application preferences for /Volume/BOOTCAMP/somethingorother
You will of course need to change it back to normal ~/
Your description though sounds like it was Mac OS X, not Windows.
If necessary clone both partitions and erase the whole raw drive (WDxxxxxx) to one when you erase. Then restore.
Had you said how it got this way....

Question regarding the installation of a J2EE 6.40 Add-in

Hi all,
I would like to install a J2EE engine on a test instance of ECC 5.0 and have a few questions regarding the installation...
Do I have to use the MASTER CD to first install the J2EE engine (Support Package 0) and then apply the latest support packages found on the SAP Marketplace?
Or should be able to directly install the J2EE Add-In by using the latest support packages found on the SAP Marketplace?
Best regards,
Xavier Vermaut

Thanks Bhavik for your reply,
That's what I actually thought but I get the following problem... Here's what I wrote into my customer message... I am still waiting for an answer and would like to get this solved ASAP
Dear SAP,
We would like to install the J2EE 6.40 Add-In on our ECC 5.0 instance
(TST) but get the following error message at the very beginning of the
installation
> Cannot find an installed ABAP system, which is a prerequisite for a
> J2EE Add-In installation. The installation cannot continue.
We checked the installation logs (sapinst_dev.log) and found the
following :
> Found these instances:
> sid: MGR, number: 00, name: DVEBMGS00, host: erpqs1a
> sid: TST, number: 10, name: DVEBMGS10, host: erpqs1a
Why does the installation say that it can not find any ABAP systems when
having previously found the 2 different instances running on this
server?
Would this problem be related to the fact that we have two instances on
this server?
Please find hereunder the way we performed this installation :
01) Download of the 4 different parts of SAP J2EE Engine 6.40 SP 10
     (Solaris 10 - Oracle)
     Part I   : SAPINST10_0-20000121.SAR         (Solaris 64)
     Part II : CTRLORA10_0-20000121.SAR         (Solaris 64)
     Part III : J2EERTOS10_0-20000121.SAR        (Solaris 64)
     Part IV : J2EERT10_0-10001982.SAR          (OS Independant)
02) Extract these 4 archives into /install/J2EE_640
03) Check Java Version and Environment Variables
04) Check Solaris Pre-Requisites
05) Adapt "product.xml" as specified in OSS Note 697535 (IGS)
06) Log in as 'root'
07) Set DISPLAY environment Variable
08) Move to the Installation directory
      ( /install/J2EE_640/SAPINST-CD/SAPINST/UNIX/SUNOS_64 )
09) ./sapinst
10) In the 'Welcome to Netweaver Installation' screen, select
      => Dialog Instance Finalization
Any idea how to get this solved?
Best regards,
Xavier Vermaut
Message was edited by: Xavier Vermaut

Ocr question - after ocr text still displays the way it was before - can the letters be changed?

hi!
i have a question regarding ocr.
the function works perfect but after ocr the letters still get displayed the way they looked from scanning.
is there a way the replace the (recognised) letters by a vector font?
shouldnt be a problem as the letter recognition worked .
cheers
frank

It would be helpful if you'd tell us what version of Acrobat you're using. The names and locations of the commands move with different versions.
The option you want is called ClearScan.
This method synthesizes a new Type 3 font that closely approximates the original, and preserves the page background using a low-resolution copy.

Pio 110D on the way....question regarding firmware

Similar Messages

Maybe you are looking for