Pismo does not boot after replacing hard drive

We have had an old Pismo for several years now. Two or so years ago we decided to replace the stock 6GB hard drive, which was getting full, with a new 60GB drive. We cloned the old drive via target disk mode, popped in the new drive, copied the data back (again via target disk mode), and were surprised when we were met with the flashing question mark/system folder icon. Sort of left it at that and forgot about it.
I stumbled upon the Pismo again today and decided to see if I couldn't get it working. After going through a few "why won't this even turn on" sessions (the machine hadn't been powered on in a few years, so pulling the internal battery and resetting the PMU fixed that), I popped the old drive back in and the machine booted just fine. Cloned the original drive (again) using Carbon Copy Cloner via target disk mode to a disk image on my MacBook. Powered it down, put the new (60GB) drive back in the Pismo, cloned the disk image back to the new drive. The data's there, because I can browse it in target disk mode, but I can't boot off the new hard drive. I can't boot off my Tiger install DVD either - the DVD drive spins up and tries to access the disc, but won't boot. I'm going to try and get my hands on the CD version of Tiger to see if there's a difference using that.
Disk Utility on the MacBook says there's nothing wrong with the Pismo's hard drive, but I'm not convinced that's the case. I'd heard about Pismos being picky with certain types of hard drives, is this true? If not, what other issues might be leading to this behavior?

Is this perhaps an artifact of the drive being formatted via target disk mode on my MacBook
I suspect that the problem lies somewhere in that situation. I suggest that you boot from the install disk as I suggested previously and reformat the HDD and reinstall the OS.
Formatting, Partitioning Erasing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
• Boot the MacBook Firewire Target Disk Mode.
• Insert install disk into MacBook's optical drive.
• Connect computers via firewire cable
• Option Boot Pismo.
• Select Install Disk for startup and click on the straight arrow.
• Select language
• Go to the Utilities menu (Tiger and later) Installer menu (Panther & earlier) and launch Disk Utility.
• Select your HDD (manufacturer ID) in left side bar.
• Select Partition tab in main panel. (You are about to create a single partition volume.)
• Click on Options button
• Select Apple Partition Map (PPC Macs)
• Click OK
• Select number of partitions in pull-down menu above Volume diagram.
(Note 1: One partition is normally preferable for an internal HDD.)
• Type in name in Name field (usually Macintosh HD)
• Select Volume Format as Mac OS Extended (Journaled)
• Click Apply/Partition button at bottom of panel.
• Select Erase tab
• Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
• Check to be sure your Volume Name and Volume Format are correct.
• Click Erase button
• Quit Disk Utility.
Open installer and begin installation process.
cornelius

Similar Messages

"F11 System Recovery" during boot does not work after Cloning hard drive.

Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
Startup Menu (F11 System Menu works properly) only on original hard drive.
Following obtained from Disk Management & diskpart in Command Prompt.
GPT Disk <700GB>
Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
Partition 7 NTFS Primary 26MB/350MB [Recovery]
Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
Acronis True Image 2015
Acronis Backup for PC
AOMEI Backupper Professional
Macrium Reflect
Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
“Recovery
Your PC needs to be repaired
A required device isn’t connected or can’t be accessed.
Error code: 0xc0000225
You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
Thank you in advanced.

Hi,
How did you clone the HDD ? One-for-one or different method ?
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Time Machine does not start after external hard drive is connected

Time Machine does not start after external hard drive is connected

These are the iCloud storage options: http://www.apple.com/icloud/includes/lightbox-storage.html
Also bear in mind that:
1. restoring data over icloud takes time
2. iCloud is not designed as a replacement to Time Machine.

MacBook Pro will not boot - have replaced hard drive and problem persists

Macbook Pro Mid 2010
4gb ram, 2.4 GHz Intel core 2 duo
Originally when I received a folder with a flashing question mark upon startup, I assumed I had a failed hard drive. I went ahead and installed a new 500GB hard drive in my machine and installed OS X Snow Leopard. I upgraded to OS X Mavericks, and I had everything running properly. The next day, I went to startup and my Mac would not boot again. The dreaded folder and question mark were back.
I'm wondering what else could be causing this problem? Is it something I can diagnose and repair myself or will I be better off taking it into someone at this point?
Thank you!

You can try replacing the hard drive cable...
Have you tried resetting the PRAM and SMC?
Does the hard drive boot when connected externally?

IMac won't boot after replacing hard drive and restoring from Time Machine

I was having problems with my iMac but upgraded to Lion when it came out. Had a few good days and then my hard drive died.
I had the drive replaced and the repair people put Snow Leopard on the new drive.
I then tried to restore everything from my Time Machine backup. At first when I tried to log on the computer wouldn't accept my password (i know it was right).
I decided to reinstall again using the snow leopard dvd i had. This time, the computer booted up (didn't ask me for a passord) and looked like it was in the process of setting things up. But Mail kept saying it was going to import messages but then quit and restarted a few seconds later. When i quit it it just came back again and again. I could see Chrome open behind it with my bookmarks in the toolbar and see other restored things, but the overall look was grey and not everything was there.
When i restarted from the HD and not the dvd i could never get past various shades of grey and the circling progress indicator. Never booted up at all.
I read about Lion having some restore hd functionality but it doesn't show up when i restart with option key. Am I in limbo between operating systems?
Any advice as to steps to take? I don't know much about this stuff.
Thanks for any help.

Yes, if you picked a Snow Leopard backup, that's what you got.
You could pick a Lion backup, and it would restore it, but that wouldn't create the Recovery HD, which you will need, sooner or later. See Using the Recovery HD. You'll need to re-download Lion for that to be created.
When you do that, after downloading but before installing Lion again, you might want to do this: Making a Lion Install disc or partition. Then if you need to reinstall Lion again, you can do it from that, instead of having to download it again.

Macbook Pro does not boot after replacing HD

I have a Macbook Pro that I bought in early 2007. It came with 10.4, and I have since upgraded to 10.5, and then 10.6.
I decided to upgrade the original internal HD to a 500GB HD. I used Time Machine to back up the orignal HD.
After performing the surgery, I turned on the MBP with my Snow Leopard install DVD. After a while reading the DVD, the MBP spits out the DVD and displays the folder with the question mark.
I then create a recovery disk on an 8GB Flash Drive, using the Snow Leopard install disk as a source. I plug in the drive, start the MBP and hold down the 'option' key. I get a grey screen with a mouse cursor, but no drive icons.
I'm puzzled. The install DVD seems to look fine on other computers, as does the flash drive. I'm planning on getting a HD enclosure and cloning my old drive to the new drive, but does anyone have any suggestions as to what's gone wrong?
Thanks!

Dale Weisshaar wrote:
After performing the surgery, I turned on the MBP with my Snow Leopard install DVD. After a while reading the DVD, the MBP spits out the DVD and displays the folder with the question mark.
Are you holding down the small case letter c the whole time. Keep holding it till the install screen comes up.
Did that, still tried to boot (sounded like the drive was reading), and still got the folder with the question mark, and the DVD was ejected.
Also, it has to be a retail disk of Snow Leopard. A machine specific disk that came with another Mac will not work. You need the universal copy.
Right, my MBP came with 10.4 originally, so this was a retail disk.

MacBook Pro does not boot past apple screen after replacing hard drive

After replacing hard drive on MacBook Pro 13 inch early 2011 model, the screen only boots to the apple logo. Do I need to re-install the OS?

The problem is that the OS is not in any where else of the MacBook Pro than in the HD / SSD. If you replace the Hard Drive, then you will need to Re-install OSX into that hard drive, it's pretty easy.
1) Power up your Macbook Pro, as fast as you can press and hold the Option key (ALT). You'll see that it opens the bootable-devices you have, you'll see a Recovery partition, click it.
(If the Hard Drive contains data do the following)
2) In the menu select Disk Utility.
3) In Disk Utility go ahead and select the Hard Drive that is inside the MBP.
4) Erase the content.
(If the Hard Drive contains no data continue with the following jumping the last 3 steps).
5) Select Re-install OSX.
6) Select the Hard Drive in which you want to install it.
Follow the steps of everything else (it should take approximately 1 hour to do the whole thing).
Hope this helps!
Later.

My mac mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone

My Mac Mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone. I had switched the start-up disk back to the original of course. Now all I see is the Apple logo. What should I do? Thanks in advance.

Try disconnecting any external devices, especially hard drives
and try rebooting.
If that doesn't help, then :
If you are running Lion, boot to the Recovery HD and run a
Repair Disk on the OSX partition.
If Snow Leopard, boot to the installl DVD and run Repair Disk.
Also, you may want to bookmark this:
http://reviews.cnet.com/8301-13727_7-57345273-263/troubleshooting-the-boot-proce ss-for-intel-macs/?tag=txt;title
for future reference. It is a pretty good explanation of the
Mac boot process and how to identify where problems may be.

How do I reinstall CS6 Extended 64-bit after replacing hard drive and OS?

How do I reinstall CS6 Extended 64-bit after replacing hard drive and Windows 7 64-bit OS?

You can download the trial installer directly. Find the appropriate link below.
You must be on a trial download page to use the links, otherwise you get an error message.
For example, load the following page: http://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_elements&loc=us
before pasting the link into the address bar.
http://trials2.adobe.com/AdobeProducts/PHSP/13/win32/Photoshop_13_LS16.7z
http://trials2.adobe.com/AdobeProducts/PHSP/13/win32/Photoshop_13_LS16.exe
You need to kepp both files downloaded into same folder and after download click on .exe file to extract .7z

LR 5 does not recognize my external hard drive. It has recognized this drive in the past. No help at any Adobe site.

LR 5 does not recognize my external hard drive. It has recognized this drive in the past. No help at any Adobe site.

My external HD contains photos I have worked on in the past.
Additionally, I have added photos to LR5 directly onto my Mac HD. (38
photos added when working in the absence of my external HD)
Presently, in the Library mode, the Le Cie external HD is not seen in the
upper left hand corner "Source" location.
The only way to "see" the La Cie HD and its photos is in the "Import" mode.
These photos have previously been imported.
I wish to use the La Cie HD as my source in the Library mode and proceed to
the Develop mode.
In other words, work on my previously imported, previously worked on
photos, now on the La Cie.

New MBP i5 does not boot after hard disk swap

Hi there,
I received my new i5 MBP today. After booting it once with the installed HDD to check if it's ok, I exchanged the hard disk for the one in my Late 2008 Macbook Pro. After doing this, my Late 2008 Macbook Pro boots fine with the (new) hard disk from the new i5 MBP, but the i5 MBP does not boot with my old hard disk.
To give you some details:
- I have installed 10.6.3 on the (old) hard disk that's not booting.
- The i5 MBP boots fine from the installation DVD
- Disk utility finds and can read my hard disk, no errors
- PRAM NVRAM reset did not help
- when booting in safe mode, I can see the system stop booting after or while loading Extensions.mkext
My guess is, it tries to boot and load the wrong Extensions for the new system (CPU? GPU?). I have no idea how to fix this.
Any help would be greatly appreciated!

Focx,
Welcome to Apple Discussions.
Inserting the drive from an earlier model MBP will probably not work. The version of the system you have on that HD is designed for earlier hardware so when you put in in your new machine it's going to be recognized. What I'd recommend is re-installing the disk that came with the new machine and of course putting the 2008's disk back in the old machine. Then use Migration Assistant on the new machine and migrate your data from the old machine into the new machine.
This will provide a much more stable system and should work just fine.
Regards,
Roger

Help - Mac Mini does not boot after re-install of OS X

Hi,
I have a Mac Book Pro and Mac Mini. I needed to reinstall my Mac Mini but lost the install disks. The install disks of the Macbook do not work (machine specific). So what I did was boot the Mac Mini in firewire target mode and installed OS X to it from the Macbook. Worked ok. Except for one thing: The Mac mini does not boot the fresh OS X installation. I get a blinking folder icon with a question mark on top of it.
I booted from the Mac OS X install disk, repaired disk permissions etc. and tried to use the "Startup Disk" utility to select the hard drive as a boot device. But that utility does not offer me to select the hard disk, it doesn't even show up (while DiskUtility can perfectly see it).
Any hints for me? I am pretty much stuck right now.
Thanks

Well, see, the fact that it wouldn't let you boot from the MacBook install disks should have been your first clue to not try to do it. There's a reason it wouldn't let you. The MacBook install disks contain a version of the OS specific to the MacBook, in order to prevent people doing what you just tried to do (ie, installing the same copy of the OS on multiple machines).
If you don't have the Mac Mini system disks any more, you'll have to go buy a copy of OS X. You could also ask for help from an Apple Store, if there's one in your area, but I honestly don't know if they would give you new disks. I would think they should (for a small fee), since Mac Mini system disks would be useless to anyone who didn't already own a Mac Mini, but you never know.

HT201250 How to restore laptop from time capsule after replacing hard drive

How do I reload all my programs and files from a time capsule after changing hard drive? Also Apple store reloaded with Snow Leopard and not Lion. Will that be a problem? Thank you

Plug the external drive into a computer by usb or whatever box you have available..
When you say blank, is it correctly formatted.. we recommend HFS+ which is Mac OS Extended (jorrnaled)
Make sure you use GUID type disk setup not MBR if it came from PC world.
Copy the files via finder from TC to the external drive.

Windows Server 2008 R2 Does not boot When Back up drive removed

I have a windows Server 2008 R2 Standard server RAID 10 installed. I have a non raid drive installed as the backup HD. The Backup drive is now failing. When I went to switch it with a new one the system does not boot and is asking for
a boot drive. I have been searching for solutions and cannot find any. Any ideas?

Hi,
Could you confirm if your boot volume is on that non-RAID disk (maybe 2 volumes on that disk and one of them is the boot volume)?
At current situation, first please test to connect the failed disk back to the device and see if it will help.
Or you may need to run a boot-up repair with an installation disk.
If you have any feedback on our support, please send to [email protected]

My iMac does not boot after update!!!

I have just update my iMac (Intel) with Apple Software update. I have not updated for quite a while and obvious there were a bunch of stuff to update on my mac. However, when the computer requests a restart, my computer simply does not restart at all. I have tried to make it restart from the apple icon, and it still stay on. So I turn it off manually and the problem kicks in. My computer start with the grey apple icon screen and the little progress indicator, but it does not boot into OS X!!! It remains in a blue screen with the mouse pointer.
I restarted it again unplugging everying and nothing changed. Then I tried Disk Repair and it does not help neither. Then I tried to hold the power button while turning it on till I get the loud beep noise and flashy light. The problem stay the same. I do not want to erase my disk...
Someone Helps!
Intel iMac 20" Dual Core / MacBook Pro 15" Mac OS X (10.4.6)

Interesting. Have you installed any third-party RAM? Is there any possibility that your RAM became loose? Make sure your existing RAM is seated properly.
Have you performed a SMC reset?
Resetting the SMC can resolve some computer issues such as not starting up:
From the Apple menu, choose Shut Down (or if the computer is not responding, hold the power button until it turns off).
Unplug all cables from the computer, including the power cord and any display cables.
Wait at least 15 seconds.
Plug the power cord back in, making sure the power button is not being pressed at the time. Then reconnect your keyboard and mouse to the computer.
Press the power button on the back to start up your computer.
Are you able to boot in SAFE mode? If so, you can trouble shoot from there.
Be sure the computer is shut down.
Press the power button.
Immediately after you hear the startup tone, press and hold the Shift key.
Tip: The Shift key should be held as soon as possible after the startup tone but not before.
Release the Shift key when you see the gray Apple and progress indicator (looks like a spinning gear).

Pismo does not boot after replacing hard drive

Similar Messages

Maybe you are looking for