Pix 501 VPN Passthrough
I am a novice/new cisco user. I have been struggling trying to configure a Cisco Pix 501 to allow passthrough of VPN traffic. I have reviewed many articles and posts but have not had success in putting the proper configuration together. I am running a Symantec VPN client to a Symantec Security Gateway. The VPN works fine when the PIX is out of the configuration.
The Pix is version 6.3 and I also have PDM 3.0 working. I am new to the routing world. I understand most concepts but I seem to be missing a vital piece of information. The error on the symantec VPN client is as follows. Error connecting tunnel to xxx.xxx.xxx.xxx. The server rejected the ISAKMP Security association. Make sure the Phase1 ID's, shared key and IKE policy are correct.
Thank you for your assistance.
Hello Tom,
I dont know if it works in 6x IOS but here is another inspection
fixup protocol ipsec-pass-thru
Also make sure that you did a one-to-one static mapping (conduits used in legacy IOS) for an unused public IP of yours because you can not PAT gre or esp to an internal host. And you may also need an outside acl
access-list outside_access_in permit gre xxx
access-list outside_access_in permit ipsec xx
access-list outside_access_in permit esp xxx
access-list outside_access_in permit ah xxx
Regards
Similar Messages
-
Can't Connect to Pix 501 VPN on Network
Hi All,
I have a software VPN client that connects just fine to the PIX 501 VPN, but I cannot ping or telnet to any services on the LAN. Below is my config and results of show cry ipsec sa. I would appreciate any suggestions to fix this.
It's been a while since I have done this. When I check the DHCP address received from the VPN, the default gateway is missing. IIRC, that is normal. What is strange is that when I ping, Windows does not show any sent packets.
Thanks,
--Drichards38
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password bgVy005CZTsaMOwR encrypted
passwd bgVy005CZTsaMOwR encrypted
hostname cisco
domain-name xxxxxx.biz
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol ftp 1024-2048
fixup protocol ftp 49152-65534
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list acl-out permit tcp any interface outside eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq telnet
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 60990
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq echo
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any interface inside eq www
access-list acl_out permit tcp any interface inside eq ftp
access-list acl_out permit tcp any interface inside eq 3389
access-list acl_out permit tcp any interface inside eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 902
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list outside_cryptomap_dyn_20 permit ip any 10.0.0.0 255.0.0.0
access-list split_tunnel_acl permit ip 10.0.0.0 255.0.0.0 any
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside aa.bb.cc.dd 255.255.255.240
ip address inside 192.168.93.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool low_vpn_pool 10.0.1.205-10.0.1.210
pdm location 172.16.0.0 255.255.0.0 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 192.168.93.0 255.255.255.0 0 0
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.67 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.68 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.69 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.70 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.71 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.72 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.73 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.74 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.75 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.76 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.77 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.78 netmask 255.255.255.255 0 0
access-group acl_out in interface outside
rip inside default version 1
route outside 0.0.0.0 0.0.0.0 aa.bb.cc.dd 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
aaa authorization command LOCAL
http server enable
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map client authentication LOCAL
crypto map outside_map interface outside
isakmp enable outside
isakmp nat-traversal 20
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup MY_VPN address-pool low_vpn_pool
vpngroup MY_VPN dns-server 4.2.2.1
vpngroup MY_VPN default-domain xxxxx.biz
vpngroup MY_VPN split-tunnel split_tunnel_acl
vpngroup MY_VPN idle-time 1800
vpngroup MY_VPN password ********
telnet 0.0.0.0 255.255.255.255 outside
telnet 192.168.93.0 255.255.255.0 inside
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 60
console timeout 0
dhcpd address 192.168.93.230-192.168.93.240 inside
dhcpd dns ff.gg.hh.ii ff.gg.hh.ii
dhcpd lease 65536
dhcpd ping_timeout 750
dhcpd domain xxxxxx.biz
dhcpd auto_config outside
dhcpd enable inside
username xxxx password xxxxxxx encrypted privilege 15
cisco(config)# show cry ipsec sa
interface: outside
Crypto map tag: outside_map, local addr. aa.bb.cc.dd
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (10.0.1.205/255.255.255.255/0/0)
current_peer: jj.kk.ll.mm:1265
dynamic allocated peer ip: 10.0.1.205
PERMIT, flags={transport_parent,}
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0
#pkts decaps: 38, #pkts decrypt: 38, #pkts verify 38
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: aa.bb.cc.dd, remote crypto endpt.: 97.93.95.133
path mtu 1500, ipsec overhead 64, media mtu 1500
current outbound spi: 3a898e67
inbound esp sas:
spi: 0xeeb64931(4004923697)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel UDP-Encaps, }
slot: 0, conn id: 1, crypto map: outside_map
sa timing: remaining key lifetime (k/sec): (4607993/28610)
IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0x3a898e67(982093415)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel UDP-Encaps, }
slot: 0, conn id: 2, crypto map: outside_map
sa timing: remaining key lifetime (k/sec): (4608000/28574)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:I just set the logging to high on all areas of the Cisco VPN client. Below is the resulting log. Everything looks ok from here:
Cisco Systems VPN Client Version 5.0.03.0530
Copyright (C) 1998-2007 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 5.1.2600 Service Pack 3
29 09:57:02.887 09/03/12 Sev=Info/4 CM/0x63100002
Begin connection process
30 09:57:02.897 09/03/12 Sev=Info/4 CM/0x63100004
Establish secure connection
31 09:57:02.897 09/03/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "a.b.c.d"
32 09:57:02.907 09/03/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with a.b.c.d.
33 09:57:02.917 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to a.b.c.d
34 09:57:03.228 09/03/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
35 09:57:03.228 09/03/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
36 09:57:03.228 09/03/12 Sev=Info/6 IPSEC/0x6370002C
Sent 47 packets, 0 were fragmented.
37 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
38 09:57:03.979 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, VID(Xauth), VID(dpd), VID(Unity), VID(?), KE, ID, NON, VID(?), VID(Nat-T), NAT-D, NAT-D, HASH) from a.b.c.d
39 09:57:04.039 09/03/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
40 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
41 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
42 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
43 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000082
Received IOS Vendor ID with unknown capabilities flag 0x000000A5
44 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
45 09:57:03.999 09/03/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
46 09:57:03.999 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to a.b.c.d
47 09:57:03.999 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
48 09:57:03.999 09/03/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0x0421, Remote Port = 0x1194
49 09:57:03.999 09/03/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
50 09:57:03.999 09/03/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
51 09:57:04.029 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
52 09:57:04.029 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_INITIAL_CONTACT) from a.b.c.d
53 09:57:04.029 09/03/12 Sev=Warning/2 IKE/0xA3000067
Received Unexpected InitialContact Notify (PLMgrNotify:886)
54 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
55 09:57:04.039 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from a.b.c.d
56 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
57 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 2 seconds, setting expiry to 86398 seconds from now
58 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
59 09:57:04.039 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
60 09:57:04.039 09/03/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
61 09:57:09.327 09/03/12 Sev=Info/4 CM/0x63100017
xAuth application returned
62 09:57:09.327 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
63 09:57:09.367 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
64 09:57:09.367 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
65 09:57:09.367 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
66 09:57:09.367 09/03/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
67 09:57:09.387 09/03/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
68 09:57:09.387 09/03/12 Sev=Info/5 IKE/0x6300005D
Firewall Policy: Product=Cisco Systems Integrated Client Firewall, Capability= (Centralized Protection Policy).
69 09:57:09.387 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
70 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
71 09:57:09.427 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
72 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.0.1.205
73 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 4.2.2.1
74 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = xxxx.biz
75 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
76 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 10.0.0.0
mask = 255.0.0.0
protocol = 0
src port = 0
dest port=0
77 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
78 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
79 09:57:09.427 09/03/12 Sev=Info/4 CM/0x63100019
Mode Config data received
80 09:57:09.427 09/03/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 10.0.1.205, GW IP = a.b.c.d, Remote IP = 0.0.0.0
81 09:57:09.437 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to a.b.c.d
82 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
83 09:57:09.477 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from a.b.c.d
84 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
85 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000046
RESPONDER-LIFETIME notify has value of 4608000 kb
86 09:57:09.477 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to a.b.c.d
87 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=D70550E6 OUTBOUND SPI = 0xB335C6DA INBOUND SPI = 0xE99E1A59)
88 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xB335C6DA
89 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0xE99E1A59
90 09:57:09.527 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 172.16.0.11 0.0.0.0 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
91 09:57:10.448 09/03/12 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=10.0.1.205/255.0.0.0
DNS=4.2.2.1,0.0.0.0
WINS=0.0.0.0,0.0.0.0
Domain=xxxx.biz
Split DNS Names=
92 09:57:10.458 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
10.0.0.0 255.0.0.0 10.0.1.205 10.0.1.205 25
10.0.1.205 255.255.255.255 127.0.0.1 127.0.0.1 25
10.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 25
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 10.0.1.205 10.0.1.205 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 10.0.1.205 0.0.0.0 1
255.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
93 09:57:10.458 09/03/12 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
94 09:57:10.458 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
10.0.0.0 255.0.0.0 10.0.1.205 10.0.1.205 1
10.0.1.205 255.255.255.255 127.0.0.1 127.0.0.1 25
10.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 25
a.b.c.d 255.255.255.255 172.16.0.1 172.16.0.11 1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.1 255.255.255.255 172.16.0.11 172.16.0.11 1
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 10.0.1.205 10.0.1.205 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 10.0.1.205 0.0.0.0 1
255.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
95 09:57:10.458 09/03/12 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
96 09:57:10.508 09/03/12 Sev=Info/4 CM/0x6310001A
One secure connection established
97 09:57:10.618 09/03/12 Sev=Info/4 CM/0x6310003B
Address watch added for 172.16.0.11. Current hostname: toughone, Current address(es): 10.0.1.205, 172.16.0.11.
98 09:57:10.638 09/03/12 Sev=Info/4 CM/0x6310003B
Address watch added for 10.0.1.205. Current hostname: toughone, Current address(es): 10.0.1.205, 172.16.0.11.
99 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
100 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
101 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xdac635b3 into key list
102 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
103 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x591a9ee9 into key list
104 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 10.0.1.205
105 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 172.16.0.11. SG: a.b.c.d
106 09:57:10.638 09/03/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
107 09:57:19.741 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
108 09:57:19.741 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445672
109 09:57:19.772 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
110 09:57:19.772 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
111 09:57:19.772 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445672, seq# expected = 3951445672
112 09:57:30.257 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
113 09:57:30.257 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445673
114 09:57:30.297 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
115 09:57:30.297 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
116 09:57:30.297 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445673, seq# expected = 3951445673
117 09:57:40.772 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
118 09:57:40.772 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445674
119 09:57:40.802 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
120 09:57:40.802 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
121 09:57:40.802 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445674, seq# expected = 3951445674
122 09:57:54.291 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
123 09:58:04.306 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
124 09:58:14.320 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
125 09:58:24.334 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
126 09:58:34.349 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
127 09:58:41.359 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
128 09:58:41.359 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445675
129 09:58:41.389 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
130 09:58:41.389 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
131 09:58:41.389 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445675, seq# expected = 3951445675
132 09:58:54.378 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
133 09:59:04.392 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
134 09:59:14.406 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
135 09:59:24.421 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
136 09:59:34.435 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
137 09:59:41.946 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
138 09:59:41.946 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445676
139 09:59:41.976 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
140 09:59:41.976 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
141 09:59:41.976 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445676, seq# expected = 3951445676
142 09:59:54.464 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA -
Hi,
We have a customer with a Pix 501(v6.3.4)(PDM v3.02) Firewall.
We can succesfully setup a VPN connection, but the client loses the Internet connection when the VPN connection is up. I found some articles on the Internet about split tunneling, but I cant figure out how to do this.
Can someone please help me out?I suppose 501 is Easy VPN server
Split tunnel says what traffic goes to VPN tunnel if you dont have split tunnel enabled all traffic iis encrypted you need specify with ACL what traffic should be encrypted
check following example whe is ACL 80 used for split tunnel
http://www.cisco.com/en/US/products/sw/secursw/ps2120/products_configuration_guide_chapter09186a0080172787.html#wp1062497
M.
Hope that helps rate if it does -
PIX 501 VPN HELP NO NETWORK ACCESS!
I need some help please..
I am trying to connect Windows 7 VPN to L2TP access on the PIX 501. I know that PIX 501 doesn't allow MSCHAP v2. The VPN connects fine but when trying to access the local network and shared drives remote desktop I am not able to connect. I already I have the IPV4 / IPV6 IP Settings on the VPN for use default gateway on remote network unchecked. Can you please help me configure this correctly if I am configuring incorrectly.
PIX Version 6.3(4)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd ANRIhDDsTteQmCkO encrypted
hostname pixfirewall
domain-name controller.hopto.org
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list out2in permit tcp any interface outside eq www
access-list out2in permit tcp any interface outside eq https
access-list out2in permit tcp any interface outside eq 3074
access-list out2in permit udp any interface outside eq 88
access-list out2in permit udp any interface outside eq 3074
access-list out2in permit udp any interface outside eq domain
access-list out2in permit tcp any interface outside eq domain
access-list out2in permit udp any interface outside eq 1701
access-list nonat permit ip 192.168.1.0 255.255.255.0 172.17.130.0 255.255.255.192
access-list vpn-cryptomap permit ip any 172.17.130.0 255.255.255.0
pager lines 24
logging on
logging timestamp
logging standby
logging buffered informational
logging trap informational
mtu outside 1500
mtu inside 1500
ip address outside dhcp setroute
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool l2tp-pool 172.17.130.1-172.17.130.254
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 192.168.1.0 255.255.255.0 0 0
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) tcp interface www 192.168.1.33 www netmask 255.255.255.255 0 0
static (inside,outside) tcp interface https 192.168.1.2 https netmask 255.255.255.255 0 0
static (inside,outside) tcp interface domain 192.168.1.30 domain netmask 255.255.255.255 0 0
static (inside,outside) udp interface domain 192.168.1.30 domain netmask 255.255.255.255 0 0
static (inside,outside) tcp interface 3074 192.168.1.30 3074 netmask 255.255.255.255 0 0
static (inside,outside) udp interface 3074 192.168.1.30 3074 netmask 255.255.255.255 0 0
static (inside,outside) udp interface 88 192.168.1.30 88 netmask 255.255.255.255 0 0
access-group out2in in interface outside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-l2tp
crypto ipsec transform-set cisco-l2tp esp-3des esp-sha-hmac
crypto ipsec transform-set cisco-l2tp mode transport
crypto dynamic-map l2tp 30 set transform-set cisco-l2tp
crypto map dmu 30 ipsec-isakmp dynamic l2tp
crypto map dmu interface outside
isakmp enable outside
isakmp key ******** address 0.0.0.0 netmask 0.0.0.0
isakmp identity address
isakmp nat-traversal 20
isakmp policy 5 authentication pre-share
isakmp policy 5 encryption 3des
isakmp policy 5 hash sha
isakmp policy 5 group 2
isakmp policy 5 lifetime 28800
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 15
console timeout 0
vpdn group 2 accept dialin l2tp
vpdn group 2 ppp authentication pap
vpdn group 2 client configuration address local l2tp-pool
vpdn group 2 client authentication local
vpdn group 2 l2tp tunnel hello 60
vpdn username Brandon password *********
vpdn enable outside
dhcpd address 192.168.1.2-192.168.1.33 inside
dhcpd dns 4.2.2.1 4.2.2.2
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
username Brandon password PX78ZeD.LCbQntqy encrypted privilege 15
terminal width 80
Cryptochecksum:6e43dff6ef4837997276c092f9204707
: end
Thanks,
BrandonYes, you can modify it.
By the way, here is a good link about MS:
Troubleshooting Microsoft Network Neighborhood After Establishing a VPN Tunnel With the Cisco VPN Client
HTH.
Portu. -
Can any one please advise me I am trying to set up a VPN on my PIX 501 and for some reason it is not working. I have posted the scrips below. If someone can advise me what I need to change that would be great.
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password P@55w0rd! encrypted
passwd P@55w0rd! encrypted
hostname CFSLXAKALAZ
domain-name akademic.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
no fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name 192.168.2.0 VPN
object-group service RemoteDesktop tcp
port-object range 3389 3389
access-list inside_access_in remark Allow all outbound UDP port 53 for DNS
access-list inside_access_in permit udp any any eq domain
access-list inside_access_in remark Allow ping to any external IP
access-list inside_access_in permit icmp any any
access-list inside_access_in remark Allow all outbound TCP connections
access-list inside_access_in permit tcp any any
access-list outside_access_in remark Allow external DNS via UDP
access-list outside_access_in permit udp any eq domain any
access-list outside_access_in remark Allow ping from outside to inside
access-list outside_access_in permit icmp any any
access-list outside_access_in remark Remote Desktop to any internal IP
access-list outside_access_in permit tcp any any object-group RemoteDesktop
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 10.20.58.30 255.255.255.0
ip address inside 192.168.2.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool donkpool 192.168.2.50-192.168.2.60
pdm location 10.20.58.0 255.255.255.0 outside
pdm location 192.168.2.0 255.255.255.0 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
route outside 0.0.0.0 0.0.0.0 10.20.58.1 1
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 10.20.58.0 255.255.255.0 outside
http 192.168.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
vpngroup donk address-pool donkpool
vpngroup donk idle-time 1800
vpngroup donk password P@55w0rd!
telnet 10.20.58.30 255.255.255.0 outside
telnet 192.168.2.0 255.255.255.0 inside
telnet timeout 5
ssh 10.20.58.0 255.255.255.0 outside
ssh 192.168.2.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.128-192.168.2.252 inside
dhcpd dns 158.152.1.58
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
terminal width 80
terminal width 80You are missing a lot of config, depending on what type of vpn you are trying to setup please follow the links below to complete it:
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/ipsecint.html
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/sit2site.html
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/basclnt.html -
I can connect but don't see any network resources.
The Vpn Client, ver:5.0.01, is running on an xp machine.
The network it is connecting to is behind a pix501- Ver. 6.3(5).
When the connection is made the remote client gets an assigned address from the vpn pool 192.168.2.10- 192.168.2.25:
The vpn client log shows:
Line:45 18:07:27.898 08/12/09 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.10/255.255.255.0
DNS=0.0.0.0,0.0.0.0
WINS=0.0.0.0,0.0.0.0
Domain=
Split DNS Names=
This is followed by these lines:
46 18:07:27.968 08/12/09 Sev=Warning/2 CVPND/0xE3400013
AddRoute failed to add a route: code 87
Destination 192.168.1.255
Netmask 255.255.255.255
Gateway 192.168.2.1
Interface 192.168.2.10
47 18:07:27.968 08/12/09 Sev=Warning/2 CM/0xA3100024
Unable to add route. Network: c0a801ff, Netmask: ffffffff, Interface: c0a8020a, Gateway: c0a80201.
48 18:07:28.178 08/12/09 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
49 18:07:28.198 08/12/09 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
50 18:07:29.760 08/12/09 Sev=Info/4 CM/0x6310001A
One secure connection established
I can ping, from the remote client, to an inside ip behind the pix even
when I get the "add route failure" shown above, but i can't ping the computer name.
I enabled NAT traversal using the PDM, But when I connect with this option I get the error that the "Remote end is NOT behind a NAT device This end IS behind a NAT device" and ping fails.
Behind the pix are a few computers with no central server so I'm not passing a WINS server to the remote client.
I set up the vpn with the wizard.
Attached is the config file.
Any suggestions would be appreciated.
Regards,
HughHugh, sure you can rate based on the overall of the conversation but you are not obligated to do so but certainly would be nice to provide ratings.
To summarized the overall narrowing down possible issues, the main goal was to ensure RA VPN configuration on the PIX501 was corrected.
1- We enabled NAT-T on the firewall - even though this was not the issue but it is required to have it there should you RA VPN from other locations - NAT travseral makes the firewall aware of NAT devices from other ends - here is some good information on NAT-T for reference in future
http://www.microsoft.com/technet/community/columns/cableguy/cg0802.mspx
2-We corrected the VPN POOL network /28 as well as the nonat access list and crypto acl to be consistant.
Here is a link for future reference with numerous PIX configuration scenarios
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/prod_configuration_examples_list.html
lastly - your only remaining issue we can say is purely isolated with MAC machine and vpn client software.
You could perhaps try different version of the client in the MAC, or also look into release notes open caveats to rule out cisco cleint versioning and MAC versioning if there is any issues.
http://www.cisco.com/en/US/products/sw/secursw/ps2308/prod_release_notes_list.html
Regards -
Pix 501 VPN Wizard, no internet
Using the straight forward VPN
Remote Access to VPN
Cisco Client 3.x or higher
Group Name & Preshared key (no cert)
EECA, Local
VPN pool configured
.....all standard stuff.
I can connect but I cannot access the internet.
Questions:
Why can't I see my network server? I can sort of map a drive by typing in \\myserve\shared folder
Why can't I get on the internet when connected to the VPN?
VPN client 5.0..07.0410
PDM 3.0.4
Pix 6.3.5
ThanksYes, you can modify it.
By the way, here is a good link about MS:
Troubleshooting Microsoft Network Neighborhood After Establishing a VPN Tunnel With the Cisco VPN Client
HTH.
Portu. -
PIX 501 VPN users can log in but no remotedesktop
Login accepted by PIX but users cannot see the network nor remote desktop to their PC.
Using PDM 2.0 novice admin.
and ideas?can they ping the private IP's of their PC?
-brad
www.ccbootcamp.com -
Cisco Pix 501 - Need help with VPN passthrough
Greetings!
Currently I have a Cisco Pix 501 version 6.3(1) which is in front of my Windows Server 2008 box. I am fairly new to firewalling, especially with the Cisco Pix; I have been able to accomplish some port forwarding for CCTV camera software, etc. but am coming to a standstill attempting to connect a company laptop (Windows 7 Professional) to the server via VPN.
Previously we had another facility which was able to connect through VPN but it has since been removed (and always seemed to not be very stable to begin with - though it was connecting to a Server 2003 box rather than 2008).
I have been through several articles both here and other forums and have attempted several of the proposed fixes. I'm almost sure at this point I've probably opened up more of my firewall then necessary and may have duplicate information attempted to complete this passthrough. My Server 2008 resides at 192.168.1.15, below is what I have thus far. The "crypto map" sections were all completed long before I took over, I believe this is how the old VPN was set up. What I have added since beginning this endevour is the "fixup protocol pptp 1723", the "access-list" entries relating to both pptp and gre, and the "static (inside, outside)" relating to the pptp.
I am still continuously getting an error on the laptop of "800" whenever I try to connect to the VPN. Any help would be greatly appreciated as I am rapidly losing hair attempting to get this situated.
: Saved
PIX Version 6.3(1)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password RysZD25GpRAOMhF. encrypted
passwd 0I6TSwviLDtVwaTr encrypted
hostname Lorway-PIX
domain-name lorwayco.com
fixup protocol ftp 21
fixup protocol ftp 22
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
no fixup protocol smtp 25
fixup protocol sqlnet 1521
names
access-list 80 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list 80 permit ip 192.168.1.0 255.255.255.0 192.168.4.0 255.255.255.0
access-list outside_access_in permit icmp any any
access-list outside_access_in permit tcp any any eq 50000
access-list outside_access_in permit udp any any eq 50000
access-list outside_access_in permit tcp any any eq smtp
access-list outside_access_in permit tcp any any eq www
access-list outside_access_in permit tcp host 66.242.236.26 any eq smtp
access-list outside_access_in permit tcp host 208.21.46.12 any eq smtp
access-list outside_access_in permit tcp host 68.59.232.176 any eq smtp
access-list outside_access_in permit tcp any any eq pop3
access-list outside_access_in permit tcp any any eq https
access-list outside_access_in permit tcp any any eq ftp
access-list outside_access_in permit tcp host 68.53.192.139 any eq smtp
access-list outside_access_in permit tcp any any eq ftp-data
access-list outside_access_in permit tcp any any eq 1009
access-list outside_access_in permit tcp any host 192.168.1.122 eq 7000
access-list outside_access_in permit tcp host 192.168.1.122 any eq 7000
access-list outside_access_in permit tcp any any eq 7000
access-list outside_access_in permit tcp any any eq pptp
access-list outside_access_in permit gre any any
access-list 10 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list 20 permit ip 192.168.1.0 255.255.255.0 192.168.4.0 255.255.255.0
access-list 30 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside 74.221.188.249 255.255.255.0
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list 80
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) tcp interface 3389 192.168.1.15 3389 netmask 255.255.255.255 0 0
static (inside,outside) tcp interface 50000 192.168.1.160 50000 netmask 255.255.255.255 0 0
static (inside,outside) udp interface 50000 192.168.1.160 50000 netmask 255.255.255.255 0 0
static (inside,outside) tcp interface smtp 192.168.1.15 smtp netmask 255.255.255.255 0 0
static (inside,outside) tcp interface https 192.168.1.15 https netmask 255.255.255.255 0 0
static (inside,outside) tcp interface www 192.168.1.15 www netmask 255.255.255.255 0 0
static (inside,outside) tcp interface pop3 192.168.1.15 pop3 netmask 255.255.255.255 0 0
static (inside,outside) tcp interface 7000 192.168.1.122 7000 netmask 255.255.255.255 0 0
static (inside,outside) tcp interface pptp 192.168.1.15 pptp netmask 255.255.255.255 0 0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 74.221.188.1 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
snmp-server host inside 192.168.1.118
no snmp-server location
no snmp-server contact
snmp-server community public
snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-pptp
sysopt connection permit-l2tp
crypto ipsec transform-set lorway1 esp-3des esp-sha-hmac
crypto map lorwayvpn 30 ipsec-isakmp
crypto map lorwayvpn 30 match address 30
crypto map lorwayvpn 30 set peer 66.18.55.250
crypto map lorwayvpn 30 set transform-set lorway1
crypto map lorwayvpn interface outside
isakmp enable outside
isakmp key ******** address 66.18.50.178 netmask 255.255.255.255
isakmp key ******** address 66.18.55.250 netmask 255.255.255.255
isakmp identity address
isakmp nat-traversal 20
isakmp policy 9 authentication pre-share
isakmp policy 9 encryption 3des
isakmp policy 9 hash sha
isakmp policy 9 group 2
isakmp policy 9 lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 60
console timeout 0
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
terminal width 80
Cryptochecksum:5c7b250c008519fe970262aa3bc28bb5
: endConfig looks good to me.
I would actually upgrade your PIX to the latest version of 6.3.x if you still have access to the software center as this PIX is on its EOL and you are running an extremely old version of code.
If you place your Windows server bypassing the PIX temporarily, I assume you are able to connect to the VPN? -
PIX 501 passthrough with to a Win VPN Server
Can this piece of %^$ pix 501 allow port 1723 to be open so users can connect to a Windows VPN server configured by PDM?
pix 6.3(5)
Outside staic IP - whatever 111.111.111.111
Inside 192.168.1.1
Win VPN server 192.168.1.10
Thanks to anybody that can help.
Note - I wnat to know if thi can be accomplished using PDM 3.0.4
This pix has to have a use other than a glorified 4 port switchYes you can enable PIX501 with version 6.3.5 for PPTP pass through.
Command line:
static (inside,outside) tcp interface 1723 192.168.1.10 1723 netmask 255.255.255.255
fixup protocol pptp 1723
access-list permit tcp any host 111.111.111.111 eq 1723
If you don't already have an access-list applied to outside interface, then you also need the following:
access-group in interface outside
Then "clear xlate" after the above configuration. I also assume that you would like to use the outside interface ip address of the PIX for the translation. Otherwise, if 111.111.111.111 is actually a spare public ip address, then the above static command should say:
static (inside,outside) 111.111.111.111 192.168.1.10 netmask 255.255.255.255
Yes, it can be accomplished using PDM. But i have to apologize that i don't have a handy access to a PDM hence, i can only advise you on the configuration using CLI.
Hope that helps a little. -
Persistent VPN between PIX 501 and ASA 5505
I am a networking newbie with 2 small retail stores. I would like to create a persistent VPN between the stores. I already have a PIX 501 firewall, and I am looking at getting an ASA 5505. Would I have any problems creating a persistent VPN between these two firewalls?
No problems whatsoever :-)
There are loads of examples for the config on the Cisco website, and basically these boxes can run exactly the same software, so the config on each is virtually the same. Main difference is the ASA defines the interfaces in a different way. Even if you have different versions of software, say 6.3 on the PIX and 7.2 on the ASA they will still work fine for the VPN, just the configs will be a lot more different. Hope this helps to remove any worries you had? -
Problem with VPN by ASA 5505 and PIX 501
Hi
I have this scenario: Firewall ASA 5505, Firewall Pix 501 (with CatOS 6.3(5) ).
I have configured this appliance for Easy VPN (server is ASA) and PIX, and remote Access with Cisco client vpn (for internal lan ASA).
When i configure the ASA i have this problem, when i configure nat for easy vpn.
This is my nat configuration:
nat (inside) 0 access-list 100
nat (inside) 1 192.168.1.0 255.255.255.0
nat (inside) 1 0.0.0.0 0.0.0.0
nat (inside) 0 0.0.0.0 0.0.0.0 outside
when i put this command:
nat (inside) 0 access-list no-nat
this command is necessary for configuration of easy vpn, but the previous nat:
nat (inside) 0 access-list 100
is replace with the latest command.To identify addresses on one interface that are translated to mapped addresses on another interface, use the nat command in global configuration mode. This command configures dynamic NAT or PAT, where an address is translated to one of a pool of mapped addresses. To remove the nat command, use the no form of this command.
For regular dynamic NAT:
nat (real_ifc) nat_id real_ip [mask [dns] [outside] [udp udp_max_conns] [norandomseq]]
no nat (real_ifc) nat_id real_ip [mask [dns] [outside] [udp udp_max_conns] [norandomseq]]
For policy dynamic NAT and NAT exemption:
nat (real_ifc) nat_id access-list access_list_name [dns] [outside] [udp udp_max_conns] [norandomseq]
no nat (real_ifc) nat_id access-list access_list_name [dns] [outside] [udp udp_max_conns] [norandomseq] -
Remote access VPN issues using Pix 501
We have taken over a network where there was little to no documentation. I have a remote access VPN terminated on a Pix 501 that is having a connectivity issue. I can connect using Cisco VPN Client. There is a server on the inside network that is used for mail etc. It has an IP of 192.168.0.4. I cannot ping it from my VPN session but from the Pix itself, I can ping it. There are different source IP's as the IP pool for the VPN session is 172.16.x.x and the inside network is 192.168.x.x. I can ping other hosts on the same inside network that are in the ARP table of the Pix. I have attached the configuration of the Pix 501. After researching, I cannot figure out what the issue is. I was assuming it was the route inside 172.16.x.x was set incorrectly but I can ping some hosts on the 192.168.x.x network. Thanks
Aru,
Hi. Thanks for responding. I did try and remove that route inside command and I still could not ping the server. I also tried removing those static translations and did a clear xlate but still no luck. This one has me puzzled. Especially since I can ping other hosts on that network and also ping the server but only from the Pix. The source on the Pix would be different 192.168.0.x than when I am connected using the VPN 172.16.1.x. That is the biggest difference. If it was routing, I would assume I could not ping any host on the 192.168.0.x network from the VPN session. I did remove that route inside as all of the other config examples did not have a specific route statement for the local pool even though it is not on the inside network. I have limited knowledge of their network as we just were told to manage it. Thanks again. -
Upgrading PIX 501 across L2L VPN
I have a PIX 501 running 6.3(5) and just need to upgrade PDM. The PIX is at a remote site and the TFTP server is across the tunnel at our corporate site. I'm not sure what to put in the tftp-server command since the TFTP server is actually out the outside interface but across the tunnel. I'm not sure what the PIX will use to source the TFTP packets. If it is the outside interface address then the PIX won't properly protect it in the tunnel. If it is the inside interface address then it should but how can that be specified. How do I copy files via TFTP across a VPN tunnel established on the outside interface?
TylerThe PIX will use the same address as for other management methods (Telnet/Web/SSH).
Just modify the current ACL with a new Entry(ACE) that specifies to tunnel tftp traffic (UDP port69) between the PIX and the TFTP server(at corporate). That ACL gets assigned to a CRYPTO MAP (should already exist) and then Crypto MAP is the assigned to an interface (should already exist).
Reference: http://www.cisco.com/warp/public/110/38.html
Regards,
Ray -
Pix 501 IPSec VPN no LAN access and no ping
Hello,
I am attempting to setup an IPSec VPN in a basic small business scenario. I am able to connect to my pix 501 via IPSec VPN and browse the internet but I am unable to ping or connect to any devices in the remote LAN. Here is my config
show config:
nterface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password xxxxx encrypted
passwd xxxxxx encrypted
hostname pixfirewall
domain-name domain.local
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name 195.7.x.x BLR-Quadria
name 176.76.1.0 LAN-CEPIC
name 176.76.1.40 ADMIN
name 176.76.1.253 SRV-Linux
name 212.234.98.224 ADSL-Quadria
name 81.80.252.129 sylob
name 176.76.1.33 poste-pcanywhere
name 176.76.1.179 TEST
name 10.1.1.0 VPN_CLIENT
name 176.76.1.100 SRVSVG01
name 176.76.1.116 SRV-ERP01
name 176.76.1.50 SRV-ERP00
object-group network WAN-Quadria
network-object BLR-Quadria 255.255.255.248
network-object ADSL-Quadria 255.255.255.248
object-group network SRV-CEPIC
network-object SRV-Linux 255.255.255.255
network-object ADMIN 255.255.255.255
network-object SRVSVG01 255.255.255.255
network-object SRV-ERP00 255.255.255.255
network-object SRV-ERP01 255.255.255.255
object-group service TCP-Linux-Quadria tcp
port-object eq 1812
port-object eq 222
port-object eq 10000
object-group service TCP-TSE-Quadria tcp
port-object eq 3389
object-group service PCAnywhereUDP udp
port-object range pcanywhere-status pcanywhere-status
access-list outside_access_in permit tcp object-group WAN-Quadria host 195.7.x.x object-group TCP-Linux-Quadria
access-list outside_access_in permit tcp object-group WAN-Quadria interface outside object-group TCP-TSE-Quadria
access-list outside_access_in permit tcp any host 195.7.x.x eq pcanywhere-data
access-list outside_access_in permit udp any host 195.7.x.x object-group PCAnywhereUDP
access-list outside_access_in permit tcp any host 195.7.x.x eq smtp
access-list inside_outbound_nat0_acl permit ip LAN-CEPIC 255.255.255.0 VPN_CLIENT 255.255.255.224
access-list outside_cryptomap_dyn_20 permit ip any VPN_CLIENT 255.255.255.224
access-list inside_access_in permit icmp LAN-CEPIC 255.255.255.0 any
access-list inside_access_in permit ip VPN_CLIENT 255.255.255.0 any
access-list CEPIC_VPN_CLIENT_splitTunnelAcl permit ip LAN-CEPIC 255.255.255.0 any
access-list outside_cryptomap_dyn_40 permit ip any VPN_CLIENT 255.255.255.224
pager lines 24
logging on
logging console debugging
logging buffered debugging
logging trap debugging
mtu outside 1500
mtu inside 1500
ip address outside pppoe setroute
ip address inside 176.76.1.254 255.255.255.0
ip verify reverse-path interface outside
ip verify reverse-path interface inside
ip audit name attaque attack action alarm drop reset
ip audit name info info action alarm drop reset
ip audit interface outside info
ip audit interface outside attaque
ip audit interface inside info
ip audit interface inside attaque
ip audit info action alarm
ip audit attack action alarm
ip audit signature 2000 disable
ip audit signature 2003 disable
ip local pool VPN_POOL 10.1.1.10-10.1.1.20
pdm location ADMIN 255.255.255.255 inside
pdm location SRV-Linux 255.255.255.255 inside
pdm location BLR-Quadria 255.255.255.248 outside
pdm location ADSL-Quadria 255.255.255.248 outside
pdm location LAN-CEPIC 255.255.255.0 inside
pdm location poste-pcanywhere 255.255.255.255 inside
pdm location sylob 255.255.255.255 outside
pdm location TEST 255.255.255.255 inside
pdm location 10.10.10.0 255.255.255.224 outside
pdm location VPN_CLIENT 255.255.255.0 inside
pdm location VPN_CLIENT 255.255.255.224 outside
pdm location SRVSVG01 255.255.255.255 inside
pdm location SRV-ERP00 255.255.255.255 inside
pdm location SRV-ERP01 255.255.255.255 inside
pdm group WAN-Quadria outside
pdm group SRV-CEPIC inside
pdm logging debugging 100
pdm history enable
arp timeout 14400
global (outside) 10 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 10 0.0.0.0 0.0.0.0 0 0
static (inside,outside) tcp 195.7.x.x 81 SRV-Linux www netmask 255.255.255.255 0 0
static (inside,outside) tcp 195.7.x.x 222 SRV-Linux ssh netmask 255.255.255.255 0 0
static (inside,outside) tcp 195.7.x.x 10000 SRV-Linux 10000 netmask 255.255.255.255 0 0
static (inside,outside) tcp 195.7.x.x 1812 SRV-Linux 1812 netmask 255.255.255.255 0 0
static (inside,outside) tcp 195.7.x.x 3389 ADMIN 3389 netmask 255.255.255.255 0 0
static (inside,outside) tcp 195.7.x.x smtp SRV-Linux smtp netmask 255.255.255.255 0 0
static (inside,outside) tcp 195.7.x.x pcanywhere-data poste-pcanywhere pcanywhere-data netmask 255.255.255.255 0 0
static (inside,outside) udp 195.7.x.x pcanywhere-status poste-pcanywhere pcanywhere-status netmask 255.255.255.255 0 0
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
aaa authorization command LOCAL
ntp server 193.55.130.2 source inside
ntp server 80.67.179.98 source outside
ntp server 194.2.0.28 source outside prefer
http server enable
http BLR-Quadria 255.255.255.248 outside
http ADSL-Quadria 255.255.255.248 outside
http ADMIN 255.255.255.255 inside
http LAN-CEPIC 255.255.255.0 inside
snmp-server host inside SRV-Linux
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt noproxyarp outside
sysopt noproxyarp inside
service resetinbound
service resetoutside
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
crypto dynamic-map outside_dyn_map 40 match address outside_cryptomap_dyn_40
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map client authentication LOCAL
crypto map outside_map interface outside
isakmp enable outside
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup CEPIC_VPN_CLIENT address-pool VPN_POOL
vpngroup CEPIC_VPN_CLIENT dns-server 176.76.1.2 ADMIN
vpngroup CEPIC_VPN_CLIENT wins-server ADMIN
vpngroup CEPIC_VPN_CLIENT default-domain domain.local
vpngroup CEPIC_VPN_CLIENT split-tunnel CEPIC_VPN_CLIENT_splitTunnelAcl
vpngroup CEPIC_VPN_CLIENT idle-time 1800
vpngroup CEPIC_VPN_CLIENT password ********
telnet timeout 5
ssh BLR-Quadria 255.255.255.248 outside
ssh ADSL-Quadria 255.255.255.248 outside
ssh LAN-CEPIC 255.255.255.0 inside
ssh timeout 5
management-access inside
console timeout 0
vpdn group pppoe_group request dialout pppoe
vpdn group pppoe_group localname xxxxx
vpdn group pppoe_group ppp authentication chap
vpdn username xxxx password xxxxx store-local
username vg_vpn password xxxxx encrypted privilege 3
username test password xxxxxx encrypted privilege 3
username quadria password xxxxx encrypted privilege 15
username jml_vpn password xxxxx encrypted privilege 3
username jr_vpn password xxxxx encrypted privilege 3
username js_vpn password xxxxx encrypted privilege 3
privilege show level 0 command version
privilege show level 0 command curpriv
privilege show level 3 command pdm
privilege show level 3 command blocks
privilege show level 3 command ssh
privilege configure level 3 command who
privilege show level 3 command isakmp
privilege show level 3 command ipsec
privilege show level 3 command vpdn
privilege show level 3 command local-host
privilege show level 3 command interface
privilege show level 3 command ip
privilege configure level 3 command ping
privilege show level 3 command uauth
privilege configure level 5 mode enable command configure
privilege show level 5 command running-config
privilege show level 5 command privilege
privilege show level 5 command clock
privilege show level 5 command ntp
privilege show level 5 mode configure command logging
privilege show level 5 command fragment
terminal width 80
Cryptochecksum:
I know this is a basic question but I would really appreaciate the help!
Thanks so much,Hi,
You could try to change the Split Tunnel ACL to Standard ACL
First removing it from the VPN configuration and then removing the ACL and creating it as Standard type ACL
Current
access-list CEPIC_VPN_CLIENT_splitTunnelAcl permit ip LAN-CEPIC 255.255.255.0 any
New
access-list CEPIC_VPN_CLIENT_splitTunnelAcl standard permit LAN-CEPIC 255.255.255.0
You could also try adding
fixup protocol icmp
fixup protocol icmp error
Have you monitored the logs while you are attempting to connect to the LAN network?
- Jouni
Maybe you are looking for
-
Hi, I got the error message while filling the data in setup table. i got message is follows in Joblog. Program terminated, time limit exceeded: 3,795,659 document item(s) updated Message no. M2227 Diagnosis The setup run exceeded the specified termin
-
BPEL Database Adapter data to B2B TP
Hi SOA/BPEL Experts In BPEL How we are going to Map my Data base data ie which i got from Database Adapter to the Partner Link Adapter Service Trading Partner Data for ex EDI, X12 V4010 210's. My Database data which i want to send to the Partner <---
-
Get/Set-NetQosPolicy with GPOs does not work
Hi, I am trying to set the QoS policy in a GPO via P$; I am using the latest patched 2012R2 Windows P$. I have noticed that when you run the command and use the switch -PolicyStore GPO:DOMAIN\GPONAME the command does not work. Bug ?? If you typ
-
In LV, using TS API, how do I specify the VI module for a Pass/Fail step?
I am writing a LabView VI which will let a user write a TestStand sequence. Each step in the seq is the same type, a Pass/Fail test. I need to specify for each step the LabView VI module location, and an input buffer. I am having difficulty finding o
-
What is it with Apple and Summer Time at the moment?
In iCal I can't scroll to April 2011 with the left tab if I have "Syria" timezone selected and can't book a multi-day event from the end of March beyond 1st April. If I switch the timezone to "Central European", then no problem at all. C'mon Apple...