PIX-520 watchdog failure problem
I tried to upgrade PIX-520 ios version up to 6.1(1) with a floppy disk which is created by boot helper file bh61.bin PIX firewall opened in boothelper> mode easily after booting floppy. Then i tried tftp downloading into the flash the file pix611.bin . There was no error but instead of asking do you want this file write to flash it rebooted with the following error!
"Watchdog timeout failure! Please contact customer support."
After all, i recognized solution by "erasedisk" file but the problem is still there. After downloading erasedisk611.bin file its output was the same. Again a watchdog timeout failure. In attachment there is a command output off all this.
What i have to do to solve this problem in ease?
Thank you.
Did you got the pix working?
I am having troubles but tried to install 7.x.
Now I am getting the Watchdog timeout failures and even when trying to use erasedisk611.bin the messages keep comming.
Jeroen
Similar Messages
-
Urgent help with PIX 520 & downgrade to 4.X ver.
Hi all,
I need help with the problem which occured recently my colleague.We had got PIX 520
with ver 6.x. But my colleague inserted into floppy disc drive floppy with ver. 4.4.7 and rebooted PIX. And it downgraded
PIX OS.
From that time we cannot boot PIX.
I tried to create bootable disk and throught tftp insert newer PIX OS but I see still this output. And PIX still reboots.
On card with Flash inserted in PIX I see the jumpers. Could someone explain me meaning?
Any idea...??
BR
jlThis section describes how to change the PIX Firewall to an earlier version of the software than the version currently running on your PIX Firewall unit. You can only downgrade the PIX Firewall software if your platform supports the earlier version.
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/upgrade.html#wp1016359 -
I have a Cisco PIX 520 that I know nothing about. The problem I have come into is that my NAT pool is running dry and I am getting clients without access to the internet. I would like to add a PAT but I have no idea what I am doing or where to start.
Could someone give me the proper commands to do this?
I don't know what more information you need so please ask questions!
Thanks.Ok, I added the PAT on Monday morning. First I ran 'global (outside) 1 123.123.123.63 netmask 255.255.255.255' and I got a warning which I can't remember the exact wording of but it was something to the effect of being an IP that is broadcast off. So instead of saving that setting I exited out of the system and the added 'global (outside) 1 123.123.123.14 netmask 255.255.255.255' and then did the 'write memory' command. I ran 'sh global' and got:
pix# sh global
global (outside) 1 123.123.123.35-123.123.123.62 netmask 255.255.255.0
global (outside) 1 123.123.123.63 netmask 255.255.255.255
global (outside) 1 123.123.123.14 netmask 255.255.255.255
As you can see it saved both the PAT enteries, not sure if this is going to be a problem and I am not sure what the command is to delete the entry.
Monday afternoon I found out that some clients were still having trouble connecting to the internet. I did some investigating and found that I need to run 'clear xlate' for the PAT to work. I did so and everything has seemed fine until today.
On my test machine I wasn't able to connect to the internet. I ran 'sh xlate' and got this:
pix# sh xlate
87 in use, 99 most used
Global 123.123.123.38 Local 192.168.74.87
Global 123.123.123.58 Local 192.168.74.58
Global 123.123.123.61 Local 192.168.74.99
Global 123.123.123.46 Local 192.168.74.14
Global 123.123.123.41 Local 192.168.74.95
Global 123.123.123.39 Local 192.168.74.124
Global 123.123.123.52 Local 192.168.74.123
Global 123.123.123.35 Local 192.168.74.17
Global 123.123.123.43 Local 192.168.74.43
Global 123.123.123.48 Local 192.168.74.105
Global 123.123.123.47 Local 192.168.74.128
Global 123.123.123.30 Local 192.168.74.30
Global 123.123.123.33 Local 192.168.74.33
Global 123.123.123.45 Local 192.168.74.31
Global 123.123.123.50 Local 192.168.74.101
Global 123.123.123.37 Local 192.168.74.93
Global 123.123.123.60 Local 192.168.74.60
Global 123.123.123.10 Local 192.168.74.10
Global 123.123.123.57 Local 192.168.74.89
Global 123.123.123.56 Local 192.168.74.56
PAT Global 123.123.123.63(1469) Local 192.168.74.94(1890)
PAT Global 123.123.123.63(1471) Local 192.168.74.94(1892)
PAT Global 123.123.123.63(1470) Local 192.168.74.94(1891)
PAT Global 123.123.123.63(1497) Local 192.168.74.94(1918)
PAT Global 123.123.123.63(1496) Local 192.168.74.94(1917)
PAT Global 123.123.123.63(1499) Local 192.168.74.94(1920)
PAT Global 123.123.123.63(1498) Local 192.168.74.94(1919)
PAT Global 123.123.123.63(1501) Local 192.168.74.94(1923)
PAT Global 123.123.123.63(1500) Local 192.168.74.94(1921)
PAT Global 123.123.123.63(1503) Local 192.168.74.94(1925)
PAT Global 123.123.123.63(1502) Local 192.168.74.94(1924)
PAT Global 123.123.123.63(1489) Local 192.168.74.94(1910)
PAT Global 123.123.123.63(1488) Local 192.168.74.94(1909)
PAT Global 123.123.123.63(1491) Local 192.168.74.94(1912)
PAT Global 123.123.123.63(1490) Local 192.168.74.94(1911)
PAT Global 123.123.123.63(1493) Local 192.168.74.94(1914)
PAT Global 123.123.123.63(1492) Local 192.168.74.94(1913)
PAT Global 123.123.123.63(1495) Local 192.168.74.94(1916)
PAT Global 123.123.123.63(1494) Local 192.168.74.94(1915)
PAT Global 123.123.123.63(1481) Local 192.168.74.94(1902)
PAT Global 123.123.123.63(1480) Local 192.168.74.94(1901)
PAT Global 123.123.123.63(1483) Local 192.168.74.94(1904)
PAT Global 123.123.123.63(1482) Local 192.168.74.94(1903)
PAT Global 123.123.123.63(1485) Local 192.168.74.94(1906)
PAT Global 123.123.123.63(1484) Local 192.168.74.94(1905)
PAT Global 123.123.123.63(1487) Local 192.168.74.94(1908)
PAT Global 123.123.123.63(1486) Local 192.168.74.94(1907)
PAT Global 123.123.123.63(1473) Local 192.168.74.94(1894)
PAT Global 123.123.123.63(1472) Local 192.168.74.94(1893)
PAT Global 123.123.123.63(1475) Local 192.168.74.94(1896)
PAT Global 123.123.123.63(1474) Local 192.168.74.94(1895)
PAT Global 123.123.123.63(1477) Local 192.168.74.94(1898)
PAT Global 123.123.123.63(1476) Local 192.168.74.94(1897)
PAT Global 123.123.123.63(1479) Local 192.168.74.94(1900)
PAT Global 123.123.123.63(1478) Local 192.168.74.94(1899)
PAT Global 123.123.123.63(1513) Local 192.168.74.94(1935)
PAT Global 123.123.123.63(1512) Local 192.168.74.94(1934)
PAT Global 123.123.123.63(1515) Local 192.168.74.94(1937)
PAT Global 123.123.123.63(1514) Local 192.168.74.94(1936)
PAT Global 123.123.123.63(1517) Local 192.168.74.94(1939)
PAT Global 123.123.123.63(1516) Local 192.168.74.94(1938)
PAT Global 123.123.123.63(1518) Local 192.168.74.94(1940)
PAT Global 123.123.123.63(1505) Local 192.168.74.94(1927)
PAT Global 123.123.123.63(1504) Local 192.168.74.94(1926)
PAT Global 123.123.123.63(1507) Local 192.168.74.94(1929)
PAT Global 123.123.123.63(1506) Local 192.168.74.94(1928)
PAT Global 123.123.123.63(1509) Local 192.168.74.94(1931)
PAT Global 123.123.123.63(1508) Local 192.168.74.94(1930)
PAT Global 123.123.123.63(1511) Local 192.168.74.94(1933)
PAT Global 123.123.123.63(1510) Local 192.168.74.94(1932)
Global 123.123.123.59 Local 192.168.74.116
Global 123.123.123.9 Local 192.168.74.9
Global 123.123.123.54 Local 192.168.74.96
Global 123.123.123.18 Local 192.168.74.18
Global 123.123.123.15 Local 192.168.74.15
Global 123.123.123.11 Local 192.168.74.11
Global 123.123.123.24 Local 192.168.74.24
Global 123.123.123.32 Local 192.168.74.32
Global 123.123.123.44 Local 192.168.74.44
Global 123.123.123.49 Local 192.168.74.108
Global 123.123.123.36 Local 192.168.74.106
Global 123.123.123.55 Local 192.168.74.55
Global 123.123.123.51 Local 192.168.74.102
Global 123.123.123.40 Local 192.168.74.40
Global 123.123.123.42 Local 192.168.74.42
Global 123.123.123.53 Local 192.168.74.114
Global 123.123.123.62 Local 192.168.74.97
Global 123.123.123.34 Local 192.168.74.34
Global 123.123.123.26 Local 192.168.74.26
As you see I have 87 in use, 99 most used. I don't even have that many systems in the building. All the PAT global connections are my test machine.
After a few minutes I was able to connect to the internet without doing anything. I ran 'sh xlate' again and got:
pix# sh xlate
39 in use, 99 most used
Global 123.123.123.38 Local 192.168.74.87
Global 123.123.123.58 Local 192.168.74.58
Global 123.123.123.61 Local 192.168.74.99
Global 123.123.123.46 Local 192.168.74.94
Global 123.123.123.41 Local 192.168.74.95
Global 123.123.123.39 Local 192.168.74.124
Global 123.123.123.52 Local 192.168.74.123
Global 123.123.123.35 Local 192.168.74.17
Global 123.123.123.43 Local 192.168.74.43
Global 123.123.123.48 Local 192.168.74.105
Global 123.123.123.47 Local 192.168.74.128
Global 123.123.123.30 Local 192.168.74.30
Global 123.123.123.45 Local 192.168.74.31
Global 123.123.123.50 Local 192.168.74.101
Global 123.123.123.37 Local 192.168.74.93
Global 123.123.123.60 Local 192.168.74.60
Global 123.123.123.10 Local 192.168.74.10
Global 123.123.123.57 Local 192.168.74.89
Global 123.123.123.56 Local 192.168.74.56
PAT Global 123.123.123.63(1589) Local 192.168.74.94(2011)
PAT Global 123.123.123.63(1588) Local 192.168.74.94(2010)
PAT Global 123.123.123.63(1590) Local 192.168.74.94(2012)
Global 123.123.123.59 Local 192.168.74.116
Global 123.123.123.9 Local 192.168.74.9
Global 123.123.123.54 Local 192.168.74.96
Global 123.123.123.18 Local 192.168.74.18
Global 123.123.123.15 Local 192.168.74.15
Global 123.123.123.11 Local 192.168.74.11
Global 123.123.123.24 Local 192.168.74.24
Global 123.123.123.32 Local 192.168.74.32
Global 123.123.123.49 Local 192.168.74.108
Global 123.123.123.36 Local 192.168.74.106
Global 123.123.123.55 Local 192.168.74.55
Global 123.123.123.51 Local 192.168.74.102
Global 123.123.123.40 Local 192.168.74.40
Global 123.123.123.53 Local 192.168.74.114
Global 123.123.123.62 Local 192.168.74.97
Global 123.123.123.34 Local 192.168.74.34
Global 123.123.123.26 Local 192.168.74.26
So as soon as my test machine connected it dropped to 39 in use, 99 most used. I'm not sure why that happened.
So my next questions for you are,
1. Do you know what that error is that I got from the first PAT entry?
2. Is it bad that I currently have two PAT's?
3. If I have to remove one of the PAT's what is the command for doing so?
4. Why did it take a few minutes before I could get out to the internet from my test machine?
5. Why did the PAT show so many IP's running through it before it connected and so few after?
Everything is going well so far and I appreciate everything you have done for me this far. I would still be banging my head against a wall if it wasn't for you.
Thank you. -
I have a new iMac14 with Yosemite. Every morning I now find a message saying my iMac has been restarted due to a "Sleep Wake Failure" problem and that a problem report has been generated. How do I fix this or even figure out what is wrong?
The warranty entitles you to complimentary phone support for the first 90 days of ownership.
If you bought the product in the U.S. directly from Apple (not from a reseller), you have 14 days from the date of delivery in which to exchange or return it for a refund. In other countries, the return policy may be different. If you bought from a reseller, its return policy applies. -
Hello, we are starting to plan our replcement of our existing PIX 520 (6.3) with a ASA 5520. Is there a tool (or guide) we can use to migrate the current config (at least parts of it) on our PIX to the ASA?
Thanks,
HarryHi,
The guide you need is here:
http://www.cisco.com/en/US/products/sw/secursw/ps2120/products_upgrade_guides09186a0080369ee2.html
HTH
Andrew. -
What is the average price apple repairing IPhone4s Display failure problem?
what is the average price apple repairing IPhone4s Display failure problem?
It depends. If your still within warranty and the display failure isn't your fault you just back up your phone then go to any apple retail store and they'll give you a new one for free. If it is your fault I would still back up your phone and go into the store. Then they'll charge you about £150 and will give you a new one. But you must have your phone backed up. That will be the first thing they ask you.
-
We are trying to fire up an old 520 to use in a lab but it doesn't have software in the flash. This is one of the floppy based ones. I can't find a boothelper on Cisco's site to create the bootdisk. It looks like Cisco still has software, but not boothelper files. Any idea if they are around someplace else?
Did you got the pix working?
I am having troubles but tried to install 7.x.
Now I am getting the Watchdog timeout failures and even when trying to use erasedisk611.bin the messages keep comming.
Jeroen -
Error Message: "Printer Failure" Problem with print or ink system . . .
Greetings!
I wasn't exactly sure where to post this, but the error message refers to printer or ink system failure so I thought this was a good place. I've been troubleshooting my parents HP OfficeJet Pro 8600 AiO for the last 2 or 3 hours with little success. I've contacted HP tech support but they wanted $200 for the work to be done and neither I nor my parents, who are retired and on a fixed income, have the money to spare.
The tech support people said it was probably a problem with the drivers, so I attempted to reinstall the software, but that didn't help at all. A brief description of the problem might shed some light on this awful situation. Since this morning, my father tried to print something and the printer itself gave the following error message on the front LCD panel on the device itself (ie, not on Windows, but on the printer's display):
"Printer Failure
There is a problem with the printer or ink system. Turn it off, then on. If the problem persists, contact HP."
Obviously my first course of action was to follow the directions. I turned it off, unplugged the cord, waited approx. 30 seconds, replugged it in and turned it back on. Nothing changed. I've also tried removing and replacing the Ink cartridges, checking the tray for a paper jam or shortage and performing a rain dance in the hopes of attracting the gods' attention xP. In short, I'm at my wits end and don't know where to go from here.
I'm unable to access the device's LCD display control panel, which controls the printer, as the error message cannot be closed. I've tried restarting the PC as well, and a lot of other basic deductive troubleshooting procedures to no avail (forgive my overuse of cliches).
Any help would be appreciated. Thank you very much in advance. I wish you all a great day, and may the god of printing protect you from the same situation. I can assure you it's most unpleasant.
Regards, Sean (frosztbyte)
P.S. I'm not sure what other information might be needed in order to help me, but ask and you shall receive any I can find.Hi frosztbyte,
I understand your parents have an OfficeJet Pro 8600 that is saying it has a printer failure, that you have thus far not been able to clear, despite your best effort and a rain dance (at least I know who to blame for the rain now ). I would be happy to help you as best I can!
The first thing I'd suggest you do is plug the printer directly to a wall outlet if it isn't already plugged to one, just to ensure the printer is getting all the power it needs to function properly. If that doesn't seem to change anything though, please have a look through this A 'Printer Failure' Message That Might Include an '0x610000f6' or '0x61xxxxxx' Error Code Displays o... document (it was steps for the same error without an error code as well) and hopefully it can help resolve the issue.
If the issue persists after trying the wall outlet and that document I would advise you try call HP again. I believe the number you called previously may have not have been HP, but another company. If you're in North America just call 1-800-474-6836, and if you're anywhere else have a look at this Contact HP Worldwide page to see what number to call for your area.
Hope this helps, have a great day!!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP -
Nokia lumia 520 push notification problem with wha...
I have a Lumia 520, and i find that i do not receive push notifications for my whatsapp messages. I have to open the application before the messages come through. I would like to know how to correct this. I have checked all my settings.
On a HTC-forum I saw the next solution, and it works also for Nokia Lumia! That means it is a Microsoft Issue!
1) Unpin Windows store from start
2) ERASE Internet Explorer History
3) ADD new language to the keyboard (Settings-->keyboard-->add keyboards
(CHOOSE A LANGUAGE THAT REQUIRE DOWNLOAD)
4) When downloading is finished, it will ask to restart and install
5) After installation and restart do the following;
A) UNINSTALL WHATSAPP
B) REINSTALL WHATSAPP (you can get conversation history back when asked, so no problem)
After this the push function works, but there is still a delay up to 10 minutes! So when you test, be patient.
NO BETTER PRESSURE MEDIUM THAN ANTI ADVERTISING SO AFTER THIS EXPEDITION PLEASE CHANGE YOUR STATUS TEXT TO:
USING WINDOWS; THAT MEANS DELAY UP TO 10 MINUTES
When all Window Phone users display that message, Microsoft has to come with a final solution!
Please spread the word -
Is there any resolution to "SIM Failure" problem?
I get this failure message several times a week on HTC 8X. It doesn't seem to be fatal and sometimes the phone recovers itself from it or other times I have to reboot. I think it is somehow associated with poor signal reception problems. Anyhow it's annoying and is my only detraction to my Windows Phone.
Hello DanDuna, let's solve this mystery! Have you tried powering off and removing the Sim card to see if there are any scratches or if it fits within the tray without movement? Try testing in Safe Mode to see if error appears: http://vz.to/1lgrhf3 You may want to test with an alternate sim card as well. Keep us posted!
WiltonA_VZW
VZW Support
Follow us on twitter @VZWSupport -
New 520 w/sleeping problem
My new 520 w/Windows7 has a sleeping problem. In spite of the Control Panel Power Management options being set to NEVER for both Battery and AC Power which is confirmed in the Lenovo Toolbox, the computer enters the sleep mode in about one minute after no mouse or keyboard activity.
Lenovo support says it is an OS problem and MS Support insists it is a hardware problem. I'm stuck in the middle.Try uninstalling the Power Manager and power management driver.
Reboot then install both again and see if it helps.
*Non Lenovo employee*
I have a Y2P (i5) ... Feel free to ping me if you want me to test some applications with your Y2P if you have the same model. I don't mind keep doing recovery on it if needed .... =) -
How do i fix 'error; texture load failure' problems for an online game?
i play chaoticgame.com online. it currently has no admin staff to help. the problem is that the website pages do not fully load. there is a function i can access that shows me all the errors im getting, most are- error; texture load failure and error; failed downloading....
this is a recent problem. also if i access the website via iphone using wifi from my home connection i get the same errors, so i dont know if this is a interent connection problem because ive had no other problems with websites.
i believe it has something to do with texture memory?Hi Lorne.V.,
How exactly are you installing NI DAQmx on the target machines? Even if you include the DAQmx merge module in your build, you will still need to install DAQmx on the target machine separately.
Can you also confirm that the DAQmx.dll is installed in the same directory on both the development and deployment machines? And that you have the same version of DAQmx on both machines?
Regards,
Lindsey W. | Applications Engineer | National Instruments -
Cisco pix 501 open port problem
Hi,
I'm running a Pix 501 for Home office and I want to open first ports for my mail client for an outside located server.
But i get following error in the log:
106023: Deny tcp src outside:<ipmailserver>/993 dst inside:<ipoutsideinterface>/1729 by access-group "outside-mail"
here's my basic config:
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password YYYYYY encrypted
passwd YYYYYY encrypted
hostname sunny
domain-name ciscopix.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol ils 389
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
no fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list outside-mail permit tcp any any eq 465
access-list outside-mail permit tcp any any eq 993
pager lines 24
logging on
logging monitor emergencies
logging buffered informational
mtu outside 1500
mtu inside 1500
ip address outside dhcp setroute
ip address inside 192.168.10.254 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 192.168.10.0 255.255.255.0 0 0
access-group outside-mail in interface outside
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet 192.168.10.0 255.255.255.0 inside
telnet timeout 5
ssh 192.168.10.0 255.255.255.0 inside
ssh timeout 60
console timeout 0
dhcpd address 192.168.10.10-192.168.10.39 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
dhcpd enable inside
username stefan password YYYYY encrypted privilege 2
terminal width 80
Cryptochecksum:
: end
[OK]
What's the problem?
Any recommondations for the config anyway?
ThanksThanks Gerhard for the answer, but i don't want to redirect the port to an inside mail server.
I try to connect to an outside mail server with a mail client from an inside pc (who is in the dhcp ip pool, i.e. 192.168.10.22).
to open the ports i added:
access-list outside-mail permit tcp any any eq 465
access-list outside-mail permit tcp any any eq 993
access-group outside-mail in interface outside
but why is there a deny because of the access-group in the log?
106023: Deny tcp src outside:/993 dst inside:/1729 by access-group "outside-mail"
Regards S. -
How to solve pdp authentication failure problem?
I've bought an iPhone 4 and the text and calling work fine, as does wifi. However, when trying to use internet without Wifi I get a "Could not activate cellular data network - PDP authentication failure".
I tried both the things in my 4s but still the same problem...
Edit: My iOS is 6.1.2 -
How do I fix my plugin failure problems?
I recently have been having problems with watching vids on youtube. None of the vids play. All I see is plugin failure. So I downgraded from adobe 13 to 12 But still the same problem.
Safari > Preferences > Privacy > Cookies and other website data:
Press the”Details” button. A sheet will drop down.
Enter YouTube in the search box at the top right corner.
Highlight the YouTube entries that shows up.
Click the “Remove” button at the bottom, then “Done”.
It is better to keep the Adobe Flash Player updated.
1. System Preferences > Flash Player > Advanced > Delete All
Press the "Delete All" button
Install Adobe Flash Player.
http://get.adobe.com/flashplayer/
Download it first. Click Safari in the menubar and select “Quit Safari”.
Follow the prompts and install it.
Restart computer. Relaunch Safari.
2. Allow Plug-ins
Safari > Preferences > Security
Internet Plug-ins > "Allow plug-ins"
Enable it.
Maybe you are looking for
-
How to remove a hard drive on a Digital HiNote Ultra CT475
I have an old HiNote Ultra CT475, that I need to remove the hard drive and have destroyed. Anyone know how to get the case off with destroying it? I have the front edge up, cause I found screws under the foot pad in front. I do not see any more screw
-
Creation of delivery with zero stock
Hello, I have two SAP system, on both system the OSS note below was implemented: 712516 Delivery item created in spite of VL367 with quantity 0 On the 1st system, when I create a delivery foritem category LZN that has no stocks the system is allowing
-
Setting "reply-to" and "from" headers"?
Using mail.app in Snow Leopard - can someone advise how I can customize the mail headers? I use an email redirection service and publicize my "[email protected]" email address to all my friends. In reality, emails to this address get redirected to my
-
BPM Process Creation: Can't find bundle oracle.bpm.fusion.soa.msg
Hi I cant create a BPM process in my Jdeveloper .4, .5 or .6. I have updated all them with the BPM extension. While creating a BPM application, the technologies being included in the application, i.e. BPM and SOA are correct. However, on the next pag
-
Filters with variables user-exits on queries
Is it possible to define complex selection criteria by using the EXIT_SAPLRRSO_001?. Something similar to what we may do a select for Sap: Select * from table where ((field1 = value1 and field2 = value2) or (field1 = value3 and field2 = Value4)). I g