PIX Firewall 525 can not start

Hi,
Today my colleague add 2 lines of access-list to our PIX 525. After 10 minutes, my firewall was rebooted and until now can't start. The booting process as listed below.
The questions are :
1. What is my OS version? Flash?
2. How to remove those 2 lines (reset the config to default)?
3. How to solve the issue?
Thanks,
Andy
Booting process
================
Rebooting..þ
Wait.....
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 00 00   8086   7192 Host Bridge
00 07 00   8086   7110 ISA Bridge
00 07 01   8086   7111 IDE Controller
00 07 02   8086   7112 Serial Bus         9
00 07 03   8086   7113 PCI Bridge
00 0D 00   8086   1209 Ethernet           11
00 0E 00   8086   1209 Ethernet           10
Cisco Secure PIX Firewall Embedded BIOS Version 4.3
Wait...ndeavor Board, Boot Block BIOS
+------------------------------------------------------------------------------+
|          System BIOS Configuration, (C) 2000 General Software, Inc.          |
+---------------------------------------+--------------------------------------+
| System CPU           : Pentium III    | Low Memory           : 638KB         |
| Coprocessor          : Enabled        | Extended Memory      : 255MB         |
| Embedded BIOS Date   : 08/25/00       | Serial Ports 1-2     : 03F8 02F8     |
+---------------------------------------+--------------------------------------+
Cisco Secure PIX Firewall BIOS (4.0) #39: Tue Nov 28 18:44:51 PST 2000
Platform PIX-525
System Flash=E28F128J3 @ 0xfff00000
Use BREAK or ESC to interrupt flash boot.
Use SPACE to begin flash boot immediately.
Reading 1528320 bytes of image from flash.
256MB RAM
System Flash=E28F128J3 @ 0xfff00000
BIOS Flash=am29f400b @ 0xd8000
mcwa i82559 Ethernet at irq 11 MAC: 0006.5336.8129
mcwa i82559 Ethernet at irq 10 MAC: 0006.5336.8128
                               ||        ||
                               ||        ||
                              ||||      ||||
                          ..:||||||:..:||||||:..
                         c i s c o S y s t e m s
                        Private Internet eXchange
                        Cisco PIX Firewall
Cisco PIX Firewall Version 6.2(1)
Licensed Features:
Failover:           Enabled
VPN-DES:            Enabled
VPN-3DES:           Disabled
Maximum Interfaces: 8
Cut-through Proxy: Enabled
Guards:             Enabled
URL-filtering:      Enabled
Inside Hosts:       Unlimited
Throughput:         Unlimited
IKE peers:          Unlimited
An internal error occurred. Specifically, a programming assertion was
violated. Copy the error message exactly as it appears, and get the
output of the show version command and the contents of the configuration
file. Then call your technical support representative.
assertion "addr < sfmm_chip_size" failed: file "sfmm.c", line 254
No thread name
Traceback:
0: 802decd5
1: 8007a8ce
2: 800769bb
3: 80078223
4: 8007635e
5: 800017d5
6: 800758ab
7: 80120ed6
    vector 0x00000003 (breakpoint)
       edi 0x8007a887
       esi 0x000000fe
       ebp 0x7ffffcb8
       esp 0x7ffffcac
       ebx 0x8007a5a3
       edx 0x000003fd
       ecx 0x0000000a
       eax 0x00000042
error code n/a
       eip 0x802dffac
        cs 0x00000008
    eflags 0x00000046
       CR2 0x00000000
Stack dump: base:0x7ffffc2c size:64, active:64
0x7ffffd2c: 0x00020000
0x7ffffd28: 0x807f2828
0x7ffffd24: 0xfffe0000
0x7ffffd20: 0x00000300
0x7ffffd1c: 0x800769bb
0x7ffffd18: 0x7ffffd48
0x7ffffd14: 0x00000001
0x7ffffd10: 0x00000002
0x7ffffd0c: 0x800762f4
0x7ffffd08: 0x804a849c
0x7ffffd04: 0x00000020
0x7ffffd00: 0x805100c0
0x7ffffcfc: 0x7ffffd48
0x7ffffcf8: 0x8007a887
0x7ffffcf4: 0x000000fe
0x7ffffcf0: 0x8007a5a3
0x7ffffcec: 0x8007a8ce
0x7ffffce8: 0x7ffffd18
0x7ffffce4: 0x80317cd4
0x7ffffce0: 0xffffffff
0x7ffffcdc: 0x80078163
0x7ffffcd8: 0x807f2828
0x7ffffcd4: 0xfffe0000
0x7ffffcd0: 0x805100c0
0x7ffffccc: 0x000000fe
0x7ffffcc8: 0x8007a5a3
0x7ffffcc4: 0x8007a887
0x7ffffcc0: 0x802dec68
0x7ffffcbc: 0x802decd5
0x7ffffcb8: 0x7ffffce8
0x7ffffcb4: 0x00000046
0x7ffffcb0: 0x00000008
0x7ffffcac: 0x802dffac *
0x7ffffca8: 0x00000042
0x7ffffca4: 0x0000000a
0x7ffffca0: 0x000003fd
0x7ffffc9c: 0x8007a5a3
0x7ffffc98: 0x7ffffcac
0x7ffffc94: 0x7ffffcb8
0x7ffffc90: 0x000000fe
0x7ffffc8c: 0x8007a887
0x7ffffc88: 0x00000003
0x7ffffc84: 0x80004779
0x7ffffc80: 0x7ffffcb8
0x7ffffc7c: 0x802c4deb
0x7ffffc78: 0x7ffffc98
0x7ffffc74: 0x7ffffd48
0x7ffffc70: 0x00000001
0x7ffffc6c: 0x000000fe
0x7ffffc68: 0x8007a5a3
0x7ffffc64: 0x7ffffd48
0x7ffffc60: 0x80120ed6
0x7ffffc5c: 0x00000007
0x7ffffc58: 0x7ffffcac
0x7ffffc54: 0x80002d70
0x7ffffc50: 0x7ffffc80
0x7ffffc4c: 0x7ffffcac
0x7ffffc48: 0x80002ab0
0x7ffffc44: 0x00000040
0x7ffffc40: 0x7ffffc80
0x7ffffc3c: 0x74656720
0x7ffffc38: 0x7ffffe28
0x7ffffc34: 0x2c737261
0x7ffffc30: 0x8007a887
Nested traceback attempted via interrupt.
Traceback output aborted.
Rebooting..þ

Urgent help!!!

Similar Messages

PIX firewall 525 on Voice Network for 5000 CC calls

Dear all ,
can some one suggest me will it be recommended to use PIX firewall 525 on Voice ( sip ) network for 5000 CC to 1000 CC calls in signaling mode since our server are using public IP so will i be able to use it without NAT / PAT also will there be any issue of QOS .
Regards

Sohail,
If your idea is to add some security between your devices the PIX will work fine (I will prefer and ASA since it can run the latest software). The quality of your voice traffic shouldn't be impacted by the PIX.
Luis Silva

Error "can not start the configuration in parallel does not correct"

Hello everybody,
I have Windows 7 SP1, and when I install Business Objects 4.1 Client, it is install correctly but when i execute the program, for example BO Rich Client, an error appear "can not start the configuration in parallel does not correct" Could you help me?
Thanks in advance!

Check this KB
1678498 - BI 4.0 Universe Designer Gives Side-by-Side configuration incorrect Error

Can not start data Collection service

I have installed Fabric Manager version 3.3.(4). In the Performance Web Client I can not start the service Data Collection is in starting forever.
I also could not stop it. I rebooted the server and the status for this service is in starting.
Thanks,

Please provide more details like: Server OS, Java version, and what type of database you are using for the FM Server. Have you considered using a newer version of FM Server?

I can not start secion in creative cloud from a macbook

I can not start secion in creative cloud from a macbook, always comes CERRO secion, and never I log in I can not start secion indesign folio builder fails me in muse could not enter if you remove it to install again, now I can not download, I tried / Library / Application Support / Adobe / OOBE rename the folder to OOBE_old setup Guide, and simply does not work, if we are paying the membership of adobe creative cloud, at least ask for is a solution, timely responses because we are losing time and therefore money, if they are solving a problem is better than what we say and if more users seek solutions and only wait.
En español.
No puedo iniciar secion en creative cloud desde una macbook, siempre sale CERRO SECION, y nunca me conecto, en indesign no puedo iniciar secion de folio builder me da error, en muse tampoco podia entrar a si que lo elimine para poder instalar nuevamente, ahora no puedo descargar, he intentado / Library / Application Support / Adobe / OOBE cambiar el nombre de la configuración rápida carpeta para OOBE_old, y simplemente no funciona, si nosotros estamos pagando la membresia de adobe creative cloud, lo menos que pedimos es una solucion, respuestas oportunas porque estamos perdiendo tiempo y consecuencia dinero, si estan resolviendo algun problema es mejor que lo digan y a si nosotros los usuarios no buscamos mas soluciones y solamente esperaremos.
we want a valid and positive response

Hello, could you please try the steps posted here: http://helpx.adobe.com/creative-cloud/kb/unable-login-creative-cloud-248.html
Please let me know if you are successful or not.

Can not start Enterprise Manager web page

I can not start Enterprise Manager web page.
Here is my steps:
1. Start enterprise manager
emctl start
Waiting for EM to initialize ...Started
2. Check status:
emctl status
EMD is up and running : 200 OK
3. Start the web page
http://myhost:1810/
4. get following error
"There was no response. The server could be down or is not responding"
System info:
Database: 8.1.7.2
OAS: 9.2.0.2
JDK: 1.3.0_02
Server OS: SunOS 5.8
My question is where is the log file of enterprise manager and what the problem is.
Thanks in advance
Don

diego,
Thank you for your help. when I try your command I get following error:
emctl start iasconsole
Unknown command option
Usage::
emctl start|stop|status
emctl reload | upload
emctl set credentials [<Target_name>[:<Target_Type>]]
emctl gencertrequest
emctl installcert [-ca|-cert] <certificate base64 text file>
emctl set ssl test|on|off|password [<old password> <new password>]
emctl set password <new pwd>
emctl authenticate <pwd>
emctl switch home [-silent <new_home>]
emctl config <options>
emctl config options can be listed by typing "emctl config"

"can not start a job" issue in AWM

Hi ALL,
I am maintaining my cube from PLSQL with following options
1. buildtype = "BACKGROUND"
2. trackstatus = "true"
3. maxjobqueues = 3
i get following error when i see the "olapsys.xml_load_log" table
***Error Occured: Failed to Build(Refresh) DB_OWNER.MY_ANALYTICAL_WORKSPACE Analytic Workspace. Can not start a job.
Can anybody explain when and why this error occurs? I have wasted a lot of time searching for this issue, but have found no person facing such issue.
Hi Keith, it will be great if you can answer this one.
My database version is 10.2.0.4.0 and AWM version is also 10.2.0.3.0
Kind Regards,
QQ
Message was edited by:
dwh_10g

Applies to:
Oracle OLAP - Version: 10.1 to 11.1
This problem can occur on any platform.
Symptoms
- We have an AW maintenance / refresh script or procedure that contains BuildType="BACKGROUND", so that the AW maintenance task will be sent to the Oracle Job queue.
- When we execute the AW maintenance / refresh script or procedure, we do not get any errors in the foreground, the script/procedure has been executed successfully.
- However when we look into the build/refresh log (see <Note 351688.1> for details) we see that the maintenance/refresh task failed with:
13:29:39 Failed to Submit a Job to Build(Refresh) Analytic Workspace <schema>.<AW Name>.
13:29:39 ***Error Occured in BUILD_DRIVER
- In the generated SQL trace for the session of the user who launches the AW build/refresh script or procedure, we see that ORA-27486 insufficient privileges error occurred at creation of the job.
We see from the relevant bit of the SQL trace that err=27486 occured while executing the #20 statement which is 'begin DBMS_SCHEDULER.CREATE_JOB ...', and the statement is parsed and tried to be executed as user having uid=91:
PARSING IN CURSOR #20 len=118 dep=2 uid=91 oct=47 lid=91 tim=1176987702199571
hv=1976722458 ad='76dd8bcc'
begin
DBMS_SCHEDULER.CREATE_JOB(:1, 'plsql_block', :2, 0, null, null, null,
'DEFAULT_JOB_CLASS', true, true, :3); end;
END OF STMT
PARSE
#20:c=1000,e=1100,p=0,cr=0,cu=0,mis=1,r=0,dep=2,og=1,tim=1176987702199561
EXEC #20:c=65990,e=125465,p=10,cr=1090,cu=3,mis=1,r=0,dep=2,og=1,tim=
1176987702325167
ERROR #20:err=27486 tim=465202984
Cause
User who tries to create a job (executes DBMS_SCHEDULER.CREATE_JOB() procedure) does not have the sufficient privileges.
Solution
1. Identify the user under which the job is supposed to be created. This user is not necessarily the same as the user who launched AW build/refresh script or procedure. Get the corresponding username from one of the %_USERS views e.g. from ALL_USERS.
e.g.
SELECT user_id,username FROM all_users WHERE user_id=91;
2. Identify the system privileges currently assigned to the user by connecting as the user whom the privileges need to be determined, and execute:
SELECT * FROM SESSION_PRIVS ORDER BY PRIVILEGE;
3. Ensure that the CREATE JOB privilege is listed.
The CREATE JOB privilege can be granted in various ways to a user:
- via role OLAP_USER or via role OLAP_DBA (see view ROLE_SYS_PRIVS for what privs are assigned to a role):
GRANT OLAP_USER TO <username>;
- explicitly
GRANT CREATE JOB TO <username>;

Error Message: "Skype can not start because the system is not available"

Try to reset all Skype settings. Quit Skype or use Windows Task Manager to kill any Skype.exe process. Go to Windows Start and in the Search/Run box type %appdata% and then press Enter or click the OK button. The Windows File Explorer will pop up. There locate a folder named “Skype”. Rename this folder to something different, e.g. Skype_old. Next go to Windows Start and in the Search/Run box type %temp%\skype and then press Enter or click the OK button. Delete the DbTemp folder. Restart Skype. N.B. If needed, you will still be able to re-establish your call and chat history. All data is still saved in the Skype_old folder.

Okay!
I'm newbie here, but it doesn't matter. I dont want to do here anything else, just write off my opinion about the Microsoft's "new" Skype, and I hope they will read...
This is a cropped image - of course hungarian, because I'm hungarian, but I think many of us could see this as well. How this is possible? "The Skype can not start because the system is not available" *** What kind of system? The Skype was on a P2P system, where is impossible that the system is not available! This is why the skype was much better than the Microsoft's messenger. Then they bought it, and make it wrong...
I found a solution for this problem, this can happen if my client is not updated. But IT IS!
How does it works? Can we use the **bleep** Skype how we would like to use? Or this time we need to find an other application (like Viber), and using that while they not buying that as well, just because that is better?
Edited to conform with the Community Guidelines
Subject/title edited to better reflect post content.

IIS Site Hosted in Web Role can not start up

Hello Team,
We occured a problem when deploying application to web role
the WaIISHost can not start up and there are two error information in event log :
Application: WaIISHost.exe
Framework Version: v4.0.30319
Description: The process was terminated due to an unhandled exception.
Exception Info: System.IO.FileLoadException
Stack:
at Microsoft.WindowsAzure.ServiceRuntime.Implementation.Loader.RoleRuntimeBridge.<InitializeRole>b__0()
at System.Threading.ExecutionContext.RunInternal(System.Threading.ExecutionContext, System.Threading.ContextCallback, System.Object, Boolean)
at System.Threading.ExecutionContext.Run(System.Threading.ExecutionContext, System.Threading.ContextCallback, System.Object, Boolean)
at System.Threading.ExecutionContext.Run(System.Threading.ExecutionContext, System.Threading.ContextCallback, System.Object)
at System.Threading.ThreadHelper.ThreadStart()
Faulting application name: WaIISHost.exe, version: 2.3.1198.663, time stamp: 0x53115226
Faulting module name: KERNELBASE.dll, version: 6.3.9600.17031, time stamp: 0x53089862
Exception code: 0xe0434352
Fault offset: 0x00000000000068d8
Faulting process id: 0x6d4
Faulting application start time: 0x01cf89326cfa011a
Faulting application path: E:\base\x64\WaIISHost.exe
Faulting module path: D:\Windows\system32\KERNELBASE.dll
Report Id: ad418c8f-f525-11e3-80bc-00155dd153c7
Faulting package full name:
Faulting package-relative application ID:
if we miss some files when deploying the environment and how to check what files are missing.
thanks in advanced.

Hello Baker.aveinc,
I understand that is a old thread, I will still go ahead and reply to this in case if this can be of help to other users.
The troubleshooting for this issue mostly depends on the status of the website on the portal. From the event logs, it appears that the faulty application is WaIISHost.exe.
I suggest that you have a look at this article that explains the scenario for Web Role Recycling.
http://blogs.msdn.com/b/kwill/archive/2013/10/03/troubleshooting-scenario-7-role-recycling.aspx
If this does not fix the issue, please post back with the status of the webrole on the portal
Thanks,
Syed Irfan Hussain

BPEL Server can not start after jazn default realm has been modified

Hi, everyone:
In order to customize my user task assigneeGroup, I set up a new realm in the jazn-data.xml using the shell (java -jar jazn.jar -shell). I tried to modify the jazn.xml file in %OraBPELPM%\integration\orabpel\system\appserver\oc4j\j2ee\home\config, and set the default-realm attribute to my new realm.
After these modification, the BPEL Server can not start, the server seems to stop after loading the first two EJB.
Does anyone ever encounter this problem? Could anyone help me?

It appears that I had the wrong oracle home and as a result some of the steps were skipped by the Universal Installer during installation, but installation was still claimed as successful. Even by launching the 'Mobile Server Repository Wizard' manually by running 'repwizard.bat' did not provide all the necessary window boxes to provide the details such as the SID, hostname, port number. I re-installed.
After starting the back-end database and then starting mobile server and testing in IE to see if the server was working by typing in http://<host name>:80/webtogo, I got the screen displaying mobile server.
Many thanks for your help.
Mark

Can not start mysql server

I recently installed mysql server on my mac os 10.6.8, earlier i had installed XAMPP on my machine but i have uninstalled it(deleted it & ran few commands in terminal), but now when i try to start server from preference pane it doesn't start & not from terminal also, it show " Could not startup MySql sever, Reason: error 255 OR Internal error"
It seems that the new mysql server settings clash somewhere with old XAMPP files/preferences. I don't even know if XAMPP is completely uninstalled or not
I'm not a mysql geek, i'm new to this! So, friends please help me with this, i need to get it working on my mac!!

I appreciate your help.
I have been offline for a long time since I had a business trip two week ago.
I can not start the apache http server, so it isn't on running status within NT services manager.
In fact, there is someting wrong---fail to create FastCGI when startup. Oracle system message tells me that syntax error exists on line 92 of isqlplus.conf but I don't know how to correct it.
Henry

Can not start http server

start http server powered by apache.I got such message:
'[alert]<5>...:FastCGI:CreateMUtex()failed
Syntax error on line 92 of c:/oracle/ora92/sqlplus/admin/isqlplus.conf:
Failed to create FastCGI application accept mutex'
my isqlplus.conf:
# Copyright (c) 2001, 2002, Oracle Corporation. All rights reserved.
# NAME
# isqlplus.conf
# PURPOSE
# Oracle HTTP Server directives for the iSQL*Plus server
# USAGE
# This file should be included in the Oracle HTTP Server
# "oracle_apache.conf" file.
# Enable handling of all virtual paths beginning with "/iplus/"
# Note: only /iplus/ is mapped, /iplus is not being mapped
<IfModule mod_alias.c>
Alias /iplus/ "C:\oracle\ora92\sqlplus\admin\iplus/"
# Disallow users from trying to access /iplus/ directory listing
<Directory "C:\oracle\ora92\sqlplus\admin\iplus">
AllowOverride None
Options FollowSymLinks
Order deny,allow
Allow from all
</Directory>
</IfModule>
# Maps all virtual paths beginning with "/isqlplus*" to the iSQL*Plus
# FastCGI application
<IfModule mod_alias.c>
ScriptAliasMatch ^/isqlplus(.*) C:\oracle\ora92\bin\isqlplus
ScriptAliasMatch ^/isqlplusdba(.*) C:\oracle\ora92\bin\isqlplus
<Directory "C:\oracle\ora92\bin">
AllowOverride None
Options FollowSymLinks
Order deny,allow
Allow from all
</Directory>
</IfModule>
# Enable handling of all virtual paths beginning with "/isqlplus"
<Location /isqlplus>
SetHandler fastcgi-script
Order deny,allow
# Comment "Allow ..." and uncomment the four lines "AuthType ..."
# to "Require ..." if Oracle HTTP authentication access is required
# for the http://.../isqlplus URL
Allow from all
#AuthType Basic
#AuthName 'iSQL*Plus'
#AuthUserFile C:\oracle\ora92\sqlplus\admin\iplus.pw
#Require valid-user
</Location>
# Enable handling of all virtual paths beginning with "/isqlplusdba".
# Note: Oracle HTTP authentication access must be configured to
# prevent unauthorized users performing DBA operations on
# the database
# Use the HTTP server utility script "htpasswd" to add users to the
# "iplusdba.pw" file.
<Location /isqlplusdba>
SetHandler fastcgi-script
Order deny,allow
AuthType Basic
AuthName 'iSQL*Plus DBA'
AuthUserFile C:\oracle\ora92\sqlplus\admin\iplusdba.pw
Require valid-user
</Location>
# Setup the iSQL*Plus FastCGI application.
<IfModule mod_fastcgi.c>
FastCgiServer C:\oracle\ora92\bin\isqlplus -port 8228 -initial-env iSQLPlusNumberOfThreads=20 -initial-env iSQLPlusTimeOutInterval=30 -initial-env iSQLPlusLogLevel=off -initial-env iSQLPlusAllowUserEntMap=none -idle-timeout 3600
</IfModule>

I appreciate your help.
I have been offline for a long time since I had a business trip two week ago.
I can not start the apache http server, so it isn't on running status within NT services manager.
In fact, there is someting wrong---fail to create FastCGI when startup. Oracle system message tells me that syntax error exists on line 92 of isqlplus.conf but I don't know how to correct it.
Henry

Can not start plugs in

Using XI tools http://server:port/index.html
will show "SAP NetWeaver Administrator" click on it and click "monitoring" getting an error messages
"can not start plugs in"

HI mtravisawan Awan
This is aa network issue
YOur user dont have admin rights. So kindly ask your admin guy to assign a port in the gatway for your machine then definitly you wil be able to display the page.
regards
Sandeep
If helpful kindly reward points

Can not start HTTP_server using "opmnctl startall" after applying p4505133

After I apply patch 4505133 on win32
10.1.0.5 PATCH SET FOR ORACLE DATABASE SERVER
I can not start HTTP_Server using opmnctl startall, got following error in apache log file:
[Thu Mar 22 22:43:54 2007] [error] (2)No such file or directory: mod_plsql: Please check your enviroment.\nORACLE_HOME is [C:\\OracleHomes\\oms10g]\nPATH is [C:\\OracleHomes\\oms10g\\bin;C:\\OracleHomes\\oms10g\\Perl\\5.6.1\\bin\\MSWin32-x86;C:\\OracleHomes\\oms10g\\Apache\\Apache\\fastcgi;C:\\OracleHomes\\oms10g\\opmn\\bin;C:\\OracleHomes\\oms10g\\opmn\\lib;C:\\OracleHomes\\oms10g\\opmn\\bin;C:\\OracleHomes\\oms10g\\opmn\\lib;C:\\OracleHomes\\oms10g\\bin;C:\\WINDOWS;C:\\WINDOWS\\system32]\nNLS_LANG is [Not Set]
[Thu Mar 22 22:44:00 2007] [crit] (2)No such file or directory: mod_plsql: Unable to initialize Oracle OCI
Any idea what is going on?
thanks,

Thanks for u r reply.
resolved this issue
oracle/middleware/oracle_idm1/bin
oidldapd folder is missing. so we copied the folder from trail environment and placed in above directory and started opmnctl services.
it worked.
Thanks and Regards,
sri485.

Can not start Messaging server in Sun Java System Messaging Server 6 2005Q1

Hi all,
I installed Sun Java System Messaging Server 6 2005Q1 from Solaris 10 DVD on Solaris 10.
After the installation, I got directory server, admin server running but messaging server not running. I can not start Messaging server (start smtp, http, pop, imap). I found in directory which I installed messaging server but I could not see script "start-msg" and "stop-msg".
# pwd
/opt/SUNWmsgsr/sbin
# ls
MoveUser ha_ip_config imquotacheck imsdirmig mkbackupdir
UpgradeMsg5toMsg6.pl hashdir imsbackup imsexport readership
configure imexpire imsconnutil imsimport reconstruct
control-params.txt iminitquota imscripter imsrestore relinker
deliver immonitor-access imsdaaci mboxutil useconfig
Any idea what might have gone wrong?
Thanks.

Thanks.
I have a problem when I configure the Messaging Server (by running the /opt/SUNWmsgsr/sbin/configure script):
Hostname mailtest for this machine is not a fully qualified domain name. Please
correct this before attempting to configure Messaging Server. Please make sure
that your DNS is working properly.
<Press ENTER to continue> {"<" goes back, "!" exits}
Can you help me fix this problem?
Thanks.

PIX Firewall 525 can not start

Similar Messages

Maybe you are looking for