PIX - IOS Router Redundancy
PIX at remote, Dual Interface/Dual ISP IOS Router at core.
Is there a way to have an IPSEC Tunnel fromt he PIX to the Dual ISP Router at the core?
Can't get the PIX to pass traffic over the second IPSEC Tunnel when one ISP/Interface goes down at the IOS Router.
Help!
Thanks,
Bob
PIX-501 at the remote
Cisco1721 with Dual ISP feeds at Central site.
I want two tunnels from the PIX to the Cisco1721.
One ISP goes down, tarffic goes over the second tunnel.
Thanks,
Bob
Similar Messages
-
Cisco IOS Router to PIX VPN Issues
Hi Everyone,
I have a small issue here which someone may be able to shed some light on.
I have a Cisco IOS router which is terminating a site-to-site VPN connection on the dialer interface. The PIX on the other end is behind a NAT router. The tunnel is being established and one subnet is able to see another when the tunnel is up. The thing we are having an issue is both networks on each side of the VPN contain multiple subnets and i cannot connect to all the subnets over the same tunnel.
Any ideas.Yes all this is setup.
I have just found out that Cisco IOS can only make connections from 1 network per crypt map unless multiple connections are made from server to host. This is quite disturbing because i have not seen this in any documentation.
Does anyone know of IOS to PIX IPsec with multiple subnets on each side of the network. -
Moving a dial-in PPTP from PIX to Router (IOS)
I've moved a dial-in PPTP config from a PIX to a IOS router, but I cannot find the equivalent IOS commands for the PIX config:
vpdn group 1 client configuration dns x.x.x.x
and
vpdn group 1 client configuration wins x.x.x.x
Anybody know what the equivalent IOS config is?Following URL will help you for the details of the PPTP configuration :
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080143a5d.shtml -
I have two issues but related and need help:
anyone know how to disable or stop a radius host test message send every seconds from a IOS router after the test statement removed and all radius server information removed from the configuration? I have this odd testing for the new ISE server. the purpose of testing is not for load balancing, but find out if IOS support different protocol using radius other than PAP if PPP is not used. after the test, I cannot stop it. I have a case opened with Cisco, the answer is no way to stop it other than reboot the router. I tried to remove aaa new model and add it back, no help. I have put an access-list on the LAN interface deny the IP any to the radius host and port, no match found.
On the ISE (version 1.1.1), due to the IOS router test cannot be stopped, the alive authentication page fills up all the authentication failure messages. anyone know how to block the host from ISE live authentication log (the router has been removed from the device page)?
below is part of messages from the IOS router (version 15.0.1M6) debug. where 10.2.2.144 is the ISE IP and totally removed from the config. there is no any radius or the ISE IP in the config.
Aug 28 10:21:15.384: AAA/SG/TEST(Req#: 1): Sending test AAA Access-Request.
Aug 28 10:21:15.384: AAA/SG/TEST(Req#: 1): Sending test AAA Accounting-Request.
Aug 28 10:21:15.384: AAA/SG/TEST: Verifying if further testing required to determine server state.
Aug 28 10:21:15.384: AAA/SG/TEST: DEAD state verification already in progress for server (10.2.2.144:1645,1646).
Aug 28 10:21:15.384: AAA/SG/TEST: Server (10.2.2.144:1645,1646) assumed DEAD. Dead time updated to 60 secs(s).
Aug 28 10:21:33.752: AAA/SG/TEST: No Test response from server (10.2.2.144:1645,1646)
Aug 28 10:21:33.976: AAA/SG/TEST: No Test response from server (10.2.2.144:1645,1646)
Aug 28 10:21:33.976: AAA/SG/TEST: Necessary responses NOT received from server (10.2.2.144:1645,1646).
Aug 28 10:21:33.976: AAA/SG/TEST: Server (10.2.2.144:1645,1646) marked DEAD. Dead time set for 60 sec(s).
Aug 28 10:21:33.976: AAA/SG/TEST: Server (10.2.2.144:1645,1646) removed from quarantine.
Aug 28 10:22:33.976: AAA/SG/TEST: Verifying if further testing required to determine server state.
Aug 28 10:22:33.976: AAA/SG/TEST: Server (10.2.2.144:1645,1646) quarantined.
Aug 28 10:22:33.976: AAA/SG/TEST: Sending 1 Access-Requests, 1 Accounting-Requests in current batch.
Aug 28 10:22:33.976: AAA/SG/TEST(Req#: 1): Sending test AAA Access-Request.
Aug 28 10:22:33.976: AAA/SG/TEST(Req#: 1): Sending test AAA Accounting-Request.
Aug 28 10:22:33.976: AAA/SG/TEST: Verifying if further testing required to determine server state.
Aug 28 10:22:33.976: AAA/SG/TEST: DEAD state verification already in progress for server (10.2.2.144:1645,1646).
Aug 28 10:22:33.976: AAA/SG/TEST: Server (10.2.2.144:1645,1646) assumed DEAD. Dead time updated to 60 secs(s).
Aug 28 10:22:52.760: AAA/SG/TEST: No Test response from server (10.2.2.144:1645,1646)
Aug 28 10:22:53.176: AAA/SG/TEST: No Test response from server (10.2.2.144:1645,1646)
Aug 28 10:22:53.176: AAA/SG/TEST: Necessary responses NOT received from server (10.2.2.144:1645,1646).
Aug 28 10:22:53.176: AAA/SG/TEST: Server (10.2.2.144:1645,1646) marked DEAD. Dead time set for 60 sec(s).
Aug 28 10:22:53.176: AAA/SG/TEST: Server (10.2.2.144:1645,1646) removed from quarantine.
Aug 28 10:21:15.384: AAA/SG/TEST(Req#: 1): Sending test AAA Access-Request.
Aug 28 10:21:15.384: AAA/SG/TEST(Req#: 1): Sending test AAA Accounting-Request.
Aug 28 10:21:15.384: AAA/SG/TEST: Verifying if further testing required to determine server state.
Aug 28 10:21:15.384: AAA/SG/TEST: DEAD state verification already in progress for server (10.2.2.144:1645,1646).
Aug 28 10:21:15.384: AAA/SG/TEST: Server (10.2.2.144:1645,1646) assumed DEAD. Dead time updated to 60 secs(s).
Aug 28 10:21:33.752: AAA/SG/TEST: No Test response from server (10.2.2.144:1645,1646)
Aug 28 10:21:33.976: AAA/SG/TEST: No Test response from server (10.2.2.144:1645,1646)
Aug 28 10:21:33.976: AAA/SG/TEST: Necessary responses NOT received from server (10.2.2.144:1645,1646).
Aug 28 10:21:33.976: AAA/SG/TEST: Server (10.2.2.144:1645,1646) marked DEAD. Dead time set for 60 sec(s).
Aug 28 10:21:33.976: AAA/SG/TEST: Server (10.2.2.144:1645,1646) removed from quarantine.
Aug 28 10:22:33.976: AAA/SG/TEST: Verifying if further testing required to determine server state.
Aug 28 10:22:33.976: AAA/SG/TEST: Server (10.2.2.144:1645,1646) quarantined.
Aug 28 10:22:33.976: AAA/SG/TEST: Sending 1 Access-Requests, 1 Accounting-Requests in current batch.
Aug 28 10:22:33.976: AAA/SG/TEST(Req#: 1): Sending test AAA Access-Request.
Aug 28 10:22:33.976: AAA/SG/TEST(Req#: 1): Sending test AAA Accounting-Request.
Aug 28 10:22:33.976: AAA/SG/TEST: Verifying if further testing required to determine server state.
Aug 28 10:22:33.976: AAA/SG/TEST: DEAD state verification already in progress for server (10.2.2.144:1645,1646).
Aug 28 10:22:33.976: AAA/SG/TEST: Server (10.2.2.144:1645,1646) assumed DEAD. Dead time updated to 60 secs(s).
Aug 28 10:22:52.760: AAA/SG/TEST: No Test response from server (10.2.2.144:1645,1646)
Aug 28 10:22:53.176: AAA/SG/TEST: No Test response from server (10.2.2.144:1645,1646)
Aug 28 10:22:53.176: AAA/SG/TEST: Necessary responses NOT received from server (10.2.2.144:1645,1646).
Aug 28 10:22:53.176: AAA/SG/TEST: Server (10.2.2.144:1645,1646) marked DEAD. Dead time set for 60 sec(s).
Aug 28 10:22:53.176: AAA/SG/TEST: Server (10.2.2.144:1645,1646) removed from quarantine.
Thanks in advance,It seems reload is the only way to fix it. I don't think there is any way to stop or ignore messages for specific host in live authentication page of ISE. From security point of view it is required to logs all the authentication hits.
Regards,
~JG
Do rate helpful posts! -
AnyConnect VPN Client on IOS Router
Hi Guys, I configured AnyConnect SSL VPN on Cisco 2811 router. It works perfectly when I login via web and run secure mobility client. However, when I connect directly from the mobility client connection fails. It does not even ask me for username and password.
Mar 7 21:36:47.613: %SSLVPN-5-SSL_TLS_CONNECT_OK: vw_ctx: UNKNOWN vw_gw: VPN_GATEWAY i_vrf: 0 f_vrf: 0 status: SSL/TLS connection successful with remote at
Mar 7 21:36:47.617: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.621: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.745: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.749: WV: Entering APPL with Context: 0x49233618,
Data buffer(buffer: 0x4925DA18, data: 0x3F57ED98, len: 1,
offset: 0, domain: 0)
Mar 7 21:36:47.749: WV: Fragmented App data - buffered
Mar 7 21:36:47.749: WV: Entering APPL with Context: 0x49233618,
Data buffer(buffer: 0x4925D818, data: 0x3F2033F8, len: 242,
offset: 0, domain: 0)
Mar 7 21:36:47.749: WV: Appl. processing Failed : 2
Mar 7 21:36:47.749: WV: server side not ready to send.
Mar 7 21:36:47.749: WV: server side not ready to send.
Mar 7 21:36:47.749: WV: server side not ready to send.
Mar 7 21:36:47.753: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.753: WV: server side not ready to send.
====================
Here is the config:
=====================
crypto pki trustpoint VPN_TRUSTPOINT
enrollment selfsigned
serial-number
subject-name CN=academy-certificate
revocation-check crl
rsakeypair RSA_KEY
crypto pki certificate chain VPN_TRUSTPOINT
ip local pool VPN_POOL 192.168.7.100 192.168.7.150
webvpn gateway VPN_GATEWAY
ip address <ip>
ssl trustpoint VPN_TRUSTPOINT
logging enable
inservice
webvpn install svc flash:/webvpn/anyconnect-win-3.1.02040-k9.pkg sequence 1
webvpn context VPN_CONTEXT
title "<title>"
ssl authenticate verify all
login-message "<message>"
policy group VPNPOLICY
functions svc-required
svc address-pool "VPN_POOL"
svc keep-client-installed
svc rekey method new-tunnel
svc split include 192.168.1.0 255.255.255.0
default-group-policy VPNPOLICY
aaa authentication list default
gateway VPN_GATEWAY
max-users 10
inservice
I have not figured out yet, why mobility client works when launched from the web and why it does not work directly. Any input or hints would be much appreciatedHi Giorgi,
This could be related to CSCti89976.
AnyConnect 3.0 doesn't work with existing IOS.
Symptoms:
Standalone AnyConnect 3.0 client does not work with an existing IOS headend.
Conditions:
AnyConnect 3.0 with an IOS Router as the headend.
Workaround:
Use AnyConnect 2.5 or use weblaunch.
Upgrade IOS
Would it be possible to upgrade the IOS version?
HTH.
Portu. -
I am trying to make VoIP call with sip between two IOS router running 12.2(15)T H.323 plus feature. When I try to make call through the SIP proxy server, it fail. The problem is how can I register the prefix my router user agent responsible for to the SIP proxy server. There seem no such command to do so in the IOS document.
When the sip voip call is between the two router directly, it work.Here is a helpful url with an overview of VoIP and SIPs:
http://www.cisco.com/univercd/cc/td/doc/product/voice/sipsols/biggulp/bgsipsol.htm -
DHCP issue on Cisco IOS router
Hi experts,
I recently got complaints that some clients can't get IP address through the DHCP server configured on a Cisco IOS router. I turned on debugging on DHCP events and packets and I see the following logs.
Mar 22 15:33:41: DHCPD: DHCPREQUEST received from client 0100.1b63.f246.8c.
Mar 22 15:33:41: DHCPD: Finding a relay for client 0100.1b63.f246.8c on interface FastEthernet1/0.10.
Mar 22 15:33:41: DHCPD: Seeing if there is an internally specified pool class:
Mar 22 15:33:41: DHCPD: htype 1 chaddr 001b.63f2.468c
Mar 22 15:33:41: DHCPD: remote id 020a0000cf6050011000000a
Mar 22 15:33:41: DHCPD: circuit id 00000000
Mar 22 15:34:02: DHCPD: DHCPREQUEST received from client 0100.1b63.f246.8c.
Mar 22 15:34:02: DHCPD: Finding a relay for client 0100.1b63.f246.8c on interface FastEthernet1/0.10.
Mar 22 15:34:02: DHCPD: Seeing if there is an internally specified pool class:
Mar 22 15:34:02: DHCPD: htype 1 chaddr 001b.63f2.468c
Mar 22 15:34:02: DHCPD: remote id 020a0000cf6050011000000a
Mar 22 15:34:02: DHCPD: circuit id 00000000
Then it will repeat and repeat for this MAC. Any reason why the router is not assigning an IP to it? It actually happens to some other MACs as well... They are from different vendors and located on different switches... I can't really find a pattern for this problem... The DHCP pool hasn't run out and it still has available IPs in it.
ThanksHi Alain, thanks for quick reply. The followings contain the output that you required. I hided the prefix of the IP with a.b.c. Thanks!
interface FastEthernet1/0.10
description : DHCP for EXHIBITION VLAN
encapsulation dot1Q 10
ip address a.b.c.1 255.255.255.128
no ip redirects
no ip unreachables
no ip proxy-arp
end
r#sh ip dhcp pool
Pool EXHIBIT :
Utilization mark (high/low) : 100 / 0
Subnet size (first/next) : 0 / 0
Total addresses : 126
Leased addresses : 47
Pending event : none
1 subnet is currently in the pool :
Current index IP address range Leased addresses
a.b.c.118 a.b.c.1 - a.b.c.126 47
#sh run | in/be dhcp
no ip dhcp use vrf connected
ip dhcp excluded-address a.b.c.1 a.b.c.11
ip dhcp excluded-address a.b.c.126
ip dhcp excluded-address a.b.c.100 a.b.c.101
ip dhcp excluded-address a.b.c.51
ip dhcp pool EXHIBIT
network a.b.c.0 255.255.255.128
default-router a.b.c.1
dns-server 207.172.3.8 207.172.3.9
domain-name xyz.com
#sh ip dhcp binding
Bindings from all pools not associated with VRF:
IP address Client-ID/ Lease expiration Type
Hardware address/
User name
a.b.c.19 0168.7f74.6260.9b Mar 23 2011 01:56 PM Automatic
a.b.c.52 0100.4854.897d.17 Mar 23 2011 12:53 PM Automatic
a.b.c.56 0100.4063.e7b5.b2 Mar 23 2011 03:33 PM Automatic
a.b.c.57 0100.1b63.f246.8c Mar 23 2011 03:34 PM Automatic
a.b.c.68 015c.5948.0b97.d6 Mar 22 2011 05:59 PM Automatic
a.b.c.69 0168.7f74.626d.67 Mar 23 2011 07:07 AM Automatic
a.b.c.70 0198.fc11.5027.1d Mar 22 2011 07:04 PM Automatic
a.b.c.71 01dc.2b61.04ba.af Mar 22 2011 10:26 PM Automatic
a.b.c.72 017c.c537.58e6.64 Mar 22 2011 08:37 PM Automatic
a.b.c.73 017c.6d62.3303.57 Mar 23 2011 03:54 AM Automatic
a.b.c.74 0124.ab81.cda4.68 Mar 23 2011 05:01 AM Automatic
a.b.c.75 0100.1e52.8f11.a5 Mar 23 2011 02:47 PM Automatic
a.b.c.76 0100.264a.5fc8.e3 Mar 23 2011 07:13 AM Automatic
a.b.c.77 017c.6d62.38cd.40 Mar 23 2011 02:06 PM Automatic
a.b.c.78 0100.1d4f.f647.79 Mar 23 2011 02:37 PM Automatic
a.b.c.79 0100.26b0.8637.3d Mar 23 2011 01:16 PM Automatic
a.b.c.81 0130.694b.e9de.82 Mar 23 2011 03:19 PM Automatic
a.b.c.82 0100.21e9.6864.80 Mar 23 2011 12:04 PM Automatic
a.b.c.83 0124.ab81.63e6.b5 Mar 23 2011 09:38 AM Automatic
a.b.c.84 0100.16b6.0455.c2 Mar 23 2011 09:42 AM Automatic
a.b.c.85 0100.1302.4c96.9e Mar 23 2011 09:49 AM Automatic
a.b.c.86 0140.a6d9.741c.e0 Mar 23 2011 12:12 PM Automatic
a.b.c.87 0100.264a.b8e9.50 Mar 23 2011 10:16 AM Automatic
a.b.c.88 0140.a6d9.4911.67 Mar 23 2011 03:19 PM Automatic
a.b.c.89 013c.7437.1e32.96 Mar 23 2011 10:27 AM Automatic
a.b.c.90 01d8.3062.689c.4b Mar 23 2011 11:55 AM Automatic
a.b.c.91 0158.946b.4df8.bc Mar 23 2011 10:49 AM Automatic
a.b.c.92 0100.2215.7368.26 Mar 23 2011 10:23 AM Automatic
a.b.c.93 0100.23df.76ea.90 Mar 23 2011 02:33 PM Automatic
a.b.c.94 0124.ab81.708d.83 Mar 23 2011 03:58 PM Automatic
a.b.c.95 0100.1cb3.163d.5a Mar 23 2011 03:13 PM Automatic
a.b.c.96 01cc.08e0.2aeb.96 Mar 23 2011 01:27 PM Automatic
a.b.c.97 0188.c663.d0d0.55 Mar 23 2011 01:57 PM Automatic
a.b.c.98 0100.1b77.08bb.89 Mar 23 2011 01:15 PM Automatic
a.b.c.99 0100.1ec2.47d7.19 Mar 23 2011 12:43 PM Automatic
a.b.c.102 0100.1310.8e74.78 Mar 23 2011 12:41 PM Automatic
a.b.c.103 0100.24d6.58b0.82 Mar 23 2011 01:44 PM Automatic
a.b.c.104 0100.2608.7df2.68 Mar 23 2011 03:23 PM Automatic
a.b.c.106 01c8.bcc8.1a86.41 Mar 23 2011 03:56 PM Automatic
a.b.c.107 01a4.6706.1e54.94 Mar 23 2011 04:08 PM Automatic
a.b.c.108 017c.c537.46ac.0e Mar 23 2011 02:41 PM Automatic
a.b.c.111 0100.037f.0ea2.19 Mar 23 2011 02:47 PM Automatic
a.b.c.112 01d8.3062.75c5.9c Mar 23 2011 03:33 PM Automatic
a.b.c.113 0021.9116.449e Mar 23 2011 03:36 PM Automatic
a.b.c.114 0100.1ff3.46d9.a9 Mar 23 2011 03:40 PM Automatic
a.b.c.116 0104.1e64.4a0d.a3 Mar 23 2011 04:21 PM Automatic
a.b.c.117 0190.27e4.4ae8.94 Mar 23 2011 04:24 PM Automatic
Thanks! -
VPN between ASA and IOS router
We have established a VPN tunnel between IOS router and ASA, however it i working only from the latter. What are the common dissimilarities whcih occur between these two devices when setting up VPN?
Do a search for the following on cisco.com- "Most Common L2L and Remote Access IPSec VPN Troubleshooting Solutions"
It should help fix any problems.
HTH and please rate. -
The following topic describes how to do L2TP/IPSec on Windows 8.
https://supportforums.cisco.com/document/9878401/l2tp-over-ipsec-cisco-ios-router-using-windows-8
However, I am trying to use the same template for Chrome OS clients and it does not work. Has it ever been set up successfully? Any ideas would be greatly appreciated.
Thank you,
Aram.Randy, I understand now!
What I would do in this case is couple of things, but this still needs some minor configuration on the router, it depends on the router managed provider but.. you should be able to ask the provider know that you want to get syslog traps from the router to your syslog server, and they should be able to provide this to you and they should provide that, after all, you are paying for services even though is a managed router by provider.
On the router thye would configure a secondary logging server.
e.i
say your syslog server is 20.20.20.20
router(config)#logging 20.20.20.20
router(config)#logging trap informational
the above informational is facility #6 out of the 7 levels of facility, 0 being emergencies 1 alerts 2 critical and so on..I believe with this facility# you will see tunnel info on the syslog.
additionally, on the access-lists pertaining to the L2L Ipsec tunnel add the keyword log at the end of each of its access-list, with the keywork log the router will send traps pertaining to the access-list to your syslog thus providing you that the connection is stablihed or not.
Rgds
-Jorge -
SSLVPN with iPhone Anyconnect and Cisco IOS Router, Certificate Authentication failed
Hello,
i have a problem regarding the authentication with a certificate from the iPhone Anyconnect 2.5 Client to a 1802 Cisco Router.
Cisco 1802 Router:
Cisco IOS Software, C180X Software (C180X-ADVENTERPRISEK9-M), Version 15.1(1)T, RELEASE SOFTWARE (fc1)
First i configured SSLVPN with username and password, in this configuration the Anyconnect Client of my iPhone works.
then i enrolled a certificate from my Windows 2008 R2 CA to the Router with the Attributes: Server Authentication and IPSEC
and i enrolled a certificate for my iPhone with Client Authentication and IPSEC
after a bunch of time ( i realy could not find a really good documentation on how to do this) i got it done, in the webvpn context configuration i made this changes here:
no aaa authentication list default
authentication certificate
ca trustpoint CA
as the "SSL VPN Configuration Guide, Cisco IOS Release 15.1M&T" says: if i want only certificate authentication i had to user the "authentication certificate" command and thats it.
as i look into the debugs it seems to me that the Router accepts the certificate of the iPhone, but then i receive a window on the iphone that wants an additional username and password authentication, and no matter what i enter there's always the same dialog coming back..
any ideas what the problem could be???
here is the configuration:
webvpn gateway WEBVPN_GW_OFFICE2
ip interface Dialer0 port 1444
ssl trustpoint CA
inservice
webvpn install svc flash:/webvpn/sslclient-win-1.1.4.179.pkg sequence 1
webvpn install svc flash:/webvpn/anyconnect-win-3.0.4235-k9.pkg sequence 2
webvpn install svc flash:/webvpn/anyconnect-dart-win-2.5.3055-k9.pkg sequence 3
webvpn context WEBVPN_CONTEXT2
secondary-color white
title-color #669999
text-color black
ssl authenticate verify all
policy group WEBVPN_POLICY2
functions svc-enabled
mask-urls
svc address-pool "SSLVPN_OFFICE1"
svc default-domain "domain.internal"
svc keep-client-installed
svc split include 192.168.0.0 255.255.0.0
svc dns-server primary 192.168.53.33
svc dns-server secondary 192.168.53.35
virtual-template 3
default-group-policy WEBVPN_POLICY2
gateway WEBVPN_GW_OFFICE2
authentication certificate
ca trustpoint CA
inservice
here is the debug:
OfficeRouter1# PASSING appctx is [0x89FAFFCC]
Nov 19 22:39:53.507: WV: sslvpn process rcvd context queue event
Nov 19 22:39:53.507: WV: sslvpn process rcvd context queue event
Nov 19 22:39:53.607: WV: sslvpn process rcvd context queue event
Nov 19 22:39:53.607: WV: Entering APPL with Context: 0x86529380,
Data buffer(buffer: 0x86543A40, data: 0x15A07AB8, len: 469,
offset: 0, domain: 0)
Nov 19 22:39:53.607: WV: http request: / with no cookie
Nov 19 22:39:53.607: WV: validated_tp : CA cert_username : matched_ctx :
Nov 19 22:39:53.607: WV: Received appinfo
validated_tp : CA, matched_ctx : ,cert_username :
Nov 19 22:39:53.607: WV: Trustpoint match successful
Nov 19 22:39:53.607: WV: Extracted username: pass: ?
Nov 19 22:39:53.607: WV: Client side Chunk data written..
buffer=0x86543640 total_len=661 bytes=661 tcb=0x8811FE60
Nov 19 22:39:53.607: WV: Appl. processing Failed : 2
Nov 19 22:39:53.607: WV: sslvpn process rcvd context queue event
BueroRouter1# PASSING appctx is [0x89FAEEC4]
Nov 19 22:40:24.028: WV: sslvpn process rcvd context queue event
Nov 19 22:40:24.032: WV: sslvpn process rcvd context queue event
Nov 19 22:40:24.132: WV: sslvpn process rcvd context queue event
Nov 19 22:40:24.132: WV: Entering APPL with Context: 0x86529380,
Data buffer(buffer: 0x86543A40, data: 0x160C4038, len: 469,
offset: 0, domain: 0)
Nov 19 22:40:24.132: WV: http request: / with no cookie
Nov 19 22:40:24.132: WV: validated_tp : CA cert_username : matched_ctx :
Nov 19 22:40:24.132: WV: Received appinfo
validated_tp : CA, matched_ctx : ,cert_username :
Nov 19 22:40:24.132: WV: Trustpoint match successful
Nov 19 22:40:24.132: WV: Extracted username: pass: ?
Nov 19 22:40:24.132: WV: Client side Chunk data written..
buffer=0x86543640 total_len=661 bytes=661 tcb=0x88D11EEC
Nov 19 22:40:24.136: WV: Appl. processing Failed : 2
Nov 19 22:40:24.136: WV: sslvpn process rcvd context queue event
Nov 19 22:40:39.764: WV: sslvpn process rcvd context queue event
Nov 19 22:40:39.880: WV: sslvpn process rcvd context queue event
Nov 19 22:40:39.892: WV: sslvpn process rcvd context queue event
Nov 19 22:40:39.892: WV: Entering APPL with Context: 0x86529380,
Data buffer(buffer: 0x86543A40, data: 0x1616FD38, len: 610,
offset: 0, domain: 0)
Nov 19 22:40:39.892: WV: http request: /webvpn.html with domain cookie
Nov 19 22:40:39.892: WV: validated_tp : cert_username : matched_ctx :
Nov 19 22:40:39.892: WV: Received appinfo
validated_tp : CA, matched_ctx : ,cert_username :
Nov 19 22:40:39.892: WV: Trustpoint match successful
Nov 19 22:40:39.892: WV: Client side Chunk data written..
buffer=0x86543640 total_len=607 bytes=607 tcb=0x88D11EEC
Nov 19 22:40:39.892: WV: Appl. processing Failed : 2
Nov 19 22:40:39.892: WV: sslvpn process rcvd context queue eventhttp://www.cisco.com/en/US/products/ps8411/products_qanda_item09186a00809aec31.shtml
HI,
Refer to
AnyConnect VPN Client FAQ
Q. Is it possible to connect the iPad, iPod, or iPhone AnyConnect VPN Client to a Cisco IOS router?
A. No. It is not possible to connect the iPad, iPod, or iPhone AnyConnect VPN Client to a Cisco IOS router. AnyConnect on iPad/iPhone can connect only to an ASA that runs version 8.0(3).1 or later. Cisco IOS is not supported by the AnyConnect VPN Client for Apple iOS. For more information, refer to the Security Appliances and Software Supported section of the Release Notes for Cisco AnyConnect Secure Mobility Client 2.4, Apple iOS 4.2 and 4.3. -
IPhone 2.1 now supports Cisco VPN Client to IOS router
Just tested it. The Cisco VPN Client in iPhone 2.1 now connects to my IOS router. Excellent.
I have a Cisco 1812 with 12.4(20)T. I know that 12.4(6)T and some other versions have an issue with the negotiation of IPSec policies which basically means that only the first proposal is considered. If the first proposal matches you have a connection. If it does not match, the connection is refused even though other proposals would be O.K.
The relevant isakmp/ipsec config should be:
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group myvpn
key mysecretkey
dns 10.0.0.2 10.0.0.3
wins 10.0.0.2
domain mydomain.example.com
pool ippool
acl 150
split-dns mydomain.example.com
netmask 255.255.255.0
crypto isakmp profile ike-myvpn-profile
match identity group myvpn
client authentication list userauthen
isakmp authorization list groupauthor
client configuration address respond
virtual-template 2
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec profile myvpn
set transform-set ESP-3DES-SHA
set isakmp-profile ike-myvpn-profile
interface Virtual-Template2 type tunnel
ip unnumbered FastEthernet1
ip nat inside
ip virtual-reassembly
tunnel mode ipsec ipv4
tunnel protection ipsec profile myvpn
See also http://www.cisco.com/en/US/docs/ios/security/configuration/guide/secipsec_virt_tunnl_ps6441_TSD_Products_Configuration_GuideChapter.html
If you have IOS 12.4(6)T or similar which has the bug I have mentioned you have to use aes instead of 3des for the transform set. The first proposal of the iPhone is aes. Be sure to check the "debug crypto ipsec" and "debug crypto isakmp" output for troubleshooting. -
Question about RPS2300 and 'redundancy" config on IOS router
We have a 2951 router connected to an RPS2300 remote power supply. On the router there are two commands applied in global config mode, "redundancy inter-device" and "redundancy". The engineer who set up the router originally states that these commands are necessary for the RPS2300 to work properly with the 2951, but the documentation for the "redundancy inter-device" and "redundancy" commands do not seem to be related to the RPS at all. Can anyone tell me if either of these commands are required for RPS, or if there is any other config that must be added to the 2951 for the RPS2300 to function properly?
An excerpt from the 2951 config:
vtp mode transparent
username <detail removed>
username <detail removed>
redundancy inter-device
redundancy
controller T1 0/0/0
As you can see, there is no additional configuration under either of the "redundancy" commands.
Thanks
-MatTo clarify, the 2951 router has an RPS-ADPTR-2921-51 module installed which connects to the RPS2300 unit.
-Mat -
Router redundancy for Channelised E1s?
Well I have two 7606 routers and around 40 channelised E1s, I have two STM - 1 mux and four STM - 4 mux at my premises, I need to design a topology such that the two 7606 routers should be redundant i.e. in case of failure another 7606 router should switch over and provide connectivity from my LAN to the MUX.
While searching I found Automatic Protection Switching as one solution where I would have to use sonet card on 7606 routers and this sonet card would connect to an Add/Drop multiplexer.
I need to know whether STM-4 mux can be connected to STM-1 card.
Also, If I use STM - 4 card then can I have 1000 interfaces for channelised E1s on one single STM-4 card?
PA-MC-STM-1 card seems to support only 256 interfaces.
http://www.cisco.com/en/US/docs/interfaces_modules/port_adapters/install_upgrade/multichannel_serial/multichannel-stm-1_install_config/2746ovr.html
Suppose if I use multiple STM-1 cards and configure APS for redundancy, and only one SONET card fails, so will the switchover be for all the cards or just the for the card which has failed?I need to design a topology such that the two 7606 routers should be redundant i.e. in case of failure another 7606 router should switch over and provide connectivity from my LAN to the MUX.
Automatic PRotection Switching (APS) is solution for STM1 card failure.Suppose if your 7606 is working but your STM 1 card fails then other card will be used by APS. But if you need redundancy for your 7606 router then i think you have to use HSRP,VRRP,GLBP whichever suits for the traffic pattern.
I need to know whether STM-4 mux can be connected to STM-1 card.
You cannot connect STM 4 card to a STM 1 card but you CAN connect STM 1 card on your STM 4 mux to STM 1 card in router.
if I use multiple STM-1 cards and configure APS for redundancy, and only one SONET card fails, so will the switchover be for all the cards or just the for the card which has failed?
APS is 1+1 kind of protection so 1 card is protecetd by 1 different card and can be used only for you have defined. So if you have 2 STM card/port in your router and want to use protect both of them then you need 2 more card/port in your router -
Amazon S3 Backup with Cisco PIX 501 Router - slowww
We are in the process of setting up an Amazon S3 network backup of the NAS server we have in our office. We are using a Synology NAS to backup to Amazon s3, and we use a Cisco PIX 501 to secure our network. The backup from the NAS to Amazon is going painfully slow, so I contacted Synology to resolve the issue. After they examined everything, they think the router is filtering outbound traffic, and this is causing the upload to slow down. I was told the upload should happen over HTTP and HTTPS, and I made sure these ports where open through the Access Rules. There are no rules defined in the Filter Settings.
I looked at the settings with the PDM, and I can't find where the filtering would be. Does someone have any insight to what could be happening? I'm not too familiar with the PIX or all the network settings involved.
Thanks!Thank you for your question. This community is for Cisco Small Business products and your question is in reference to a Cisco Elite/Classic product. Please post your question in the Cisco NetPro forums located here:
- Wireless ----> Wireless - Mobility http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748.SJ3A?page=Wireless_-_Mobility_discussion
This forum has subject matter experts on Cisco Elite/Classic products that may be able to answer your question.
THANKS -
All,
I have a friend trying to configure an existing PIX. They needed to change IP addresses due to ISP switch. Config was very basic but whenever he puts in the route outside command the PIX seems to take it but then he is saying it is disappearing when he checks the config. Does anyone have any ideas what this could be? He only changed outside IP address, a static translation
All replies rated. Thanks in advance!Hi Angel,
My assumption is that you have a speed issue between the outside interface of the PIX and the new ISP equipment.
You have statically set the outside interface "interface ethernet0 10baset"
Please post :
show int e0
PS : nice software version 6.2
Regards
Dan
Maybe you are looking for
-
Can only see some videos that are on camera's SD card
I would like to be able to directly import videos from my camera's SD card into iPhoto, but when I put the card in my Mac, only some of the videos show up. If I look in Finder, I can see all the clips, open them in Quicktime, export them to the compu
-
Tricky query needing clever SQL...
A table called alt_websearch_log records the time it takes to complete each search performed on a website. I am therefore able to write something like this: select to_char(search_date,'DD/MON/YYYY'), count(*), avg(searchtime_secs), max(searchtime_sec
-
I have recently installed Windows 7 Home Premium and Adobe Reader 9.4.0. Whilst in Adobe Reader I attempt the attach to Email and receive this error message "Acrobat is unable to connect to your email program". Any Ideas how I overcome this problem.
-
ITunes generated errors???
early this weekend i moved several iTunes applications to a different drive. now iTunes wont work. when i try and open it it says that "iTunes.exe has generated errors, and will be closed by windows. you will need to restart the program." also when i
-
How to calculate period between date/time?
All, I have not been able to find any function module that does this. I have a create date/time from a table (VBAK). I need to calculate the difference in days/hours/minutes (seconds not needed) between the date in this table and the current date/tim