Pl. help me install a PCI card in a solaris 2.6 system

Hello,
I am working on a cpci chassis with Sun CP1400 processor card running Solaris 2.6. I am trying to install a voip card from AudioCodes. After installing the driver, and the card, the software doesn't seem to recognize the board.
I ran "show-devs" from the ok prompt. It doesn't list the card. Also, there is no entry for the driver in /etc/driver_aliases. I am not sure if the board is faulty, or the driver is not properly installed.
The driver.conf indicates its a pseudo driver (I dont know if this makes any difference). When I run pci_scan that came with the driver it listed a device on the bus with vendor id = 0x10b5. I think this is the plx chip on the card. But I don't see any AudioCodes vendor, and device ids in the list.
Thanks for your time.
Sridhar
[email protected]

It is possible that this card may not be compatible with this Solaris
system.
You may want to check these sites out for driver related information:
http://soldc.sun.com/developer/support/driver/
http://soldc.sun.com/developer/support/driver/IO_kit/PCI.html
Thx
Tushar Patel.

Similar Messages

How to install a PCI card in my HP 110-335t expansion slot?

The HP 110-335t desktop comes with one expansion slot, per the product spec. Right? How do I open up the box and install a PCI card?
This question was solved.
View Solution.

Hi,
Review this HP posted information.
You can use the PCI-E mini-slot for a wireless LAN card. Contct HP Support or Sales and get a recommendation. You will still need to configure an antenna.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Broken sound card, Can i install a pci card and get sound

I fried my internal sound card plugging up my mixer through my headphone jack. I have a mirror door, dual 1 ghz prossesors. Can i just install a m-audio pci card and get my sound back. i hope so. thanks.

The answer is yes, though there seems to be very few Mac compatible sound cards. This is probably because Macs always came with sound built in. The exceptions are the Xserve which have no sound section. I have a dual 1.33GHz G4 Xserve that I have fitted with a M-Audio Audiophile 192 PCI card. This works well but is expensive new (I got mine used). My only complaint (as a general purpose sound card) you have to use the M-Audio app to change the volume - the normal volume controls don't work.
MUCH cheaper is the USB sound card option. I also have a Griffin iMic on my work Mac and this is plugged into my keyboard usb slot. That means I can conveniently plug my headphones in with just a short cord. Works great, sounds great, and works with the standard volume controls.

Help with installing new graphics card

Hi I have a 3 year old hpe575a (hp pavillion)
Intel i7 2600, 8gb ram
Orginally had a ati hd radeon 2gb (not sure what model)
in it
after 2 years the radeon finally melted ( always had overheating problems in the australian summer )
so I bought a nvidia gtx630m which had the same connections and power requirements and connections as the radeon
I csnt seem to get it working, despite the card powering up, and loading the splash screen it doesnt go any further, I can get to the network boot screen or the hp splash screen but no further, and I cant find any bios updates for my mptherboard (pegatron) so do I need a new motherboard? The computer works 100% fine without the new graphics card
Should I get a new motherboard. Or graphics card? which would be cheaper? or is there someway to get the current system to work with the new graphics card? thanks -zac

Hi,
The existing card is an "AMD Radeon HD6570 (2 GB)". I don't know how you can fit a Nvidia GTX630M to your machine because this card is for laptop:
     http://www.geforce.com/hardware/notebook-gpus/geforce-gt-630m/specifications
Probably you are talking about the following card:
    http://www.geforce.com/hardware/desktop-gpus/geforce-gt-630/specifications
The card should be able to use 300W PSU on your machine (no need new PSU). My suggestion:
(a) Update BIOS to the latest one, please check, should be "Version7.15 Rev. A" the motherboard is Cleveland
     http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=cp-101150-1&cc=us&dlc=en&lc=en...
(b) Install driver for new card
Hope this helps.
Note: Autumn now but still hot isn't it ?
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Tusgsten E2 help with installing SDHC 4gb Card. I cant seam to format

null
Post relates to: Tungsten E2

Hello Bean-46 and welcome to the Palm forums.
The Tungsten E2, out of the box, is not compatible with SDHC cards. If you are willing to try a third-party add on, PowerSDHC should provide you with the driver you need to access the newer, larger capactiy cards. I strongly suggest that if you go this route, you download and install the trial first.
Alan G
Post relates to: Treo 755p (Sprint)

Upgraded to USB 2.0 with pci card...works 1 out of 10 times????

Hi,
Anyone having this problem? I installed a pci card with usb 2.0
The high-speed bus is recognized in my "about this mac". However, if I hook up my ipod or any device for that matter, it doesn't recognize it. Do I just need to wait longer? When I first installed the car I did have it connect a few times. But it's very inconsistent. I'm running 10.3.9 and I'm about to upgrade to 10.4. Might this help?
Thanks in advance
Pete

What brand/model card did you install. Not all USB 2.0 PCI cards work in a Mac. Your best bet is any card with a NEC PD720100 or PD720101 chipset (xlr8yourmac results recommend the same). Read this for more feedback: http://www.xlr8yourmac.com/firewire/fwusb_card_deepsleep.html
Stick with the NEC chip, and try NOT to use drivers, OS X doesn't need the drivers.
All of these Cards are NEC chipset based
Adaptec 3100LP
BAFO BF-460
Belkin F5U220
GWC UC-160
IOGear GIC250U & GIC251U
Keyspan U2PCI-5
O'toLink U2-C2A, U2-C2B, U2-P20N & U2-P50
Ratoc PCIU5
USBWholesale UII-PCIP
I recently installed an IOGear GIC251U. Was plug & play.
If you plug your mouse imto the card, does the mouse work?
 Cheers, Tom

Pcie card compatability with mac pro

I started getting regular Kernel Panics after installing a PCIe card (in slot 3) to connect my 750gb seagate pro drive to my mac pro via eSATA (the specs for the PCIe card are below).
http://www.avlab.com.tw/sata/10060109000bx.htm
I have uninstalled the drivers and my mac has stopped crashing. My problem is that since the silgate 3132 driver is (im told) pretty much universal for running this kind of pcie card, how can I be sure that if I purchase another card it won't start causing kernel panics again?
Any help much appreciated,
Henry

I know im being stupid (sorry) but what do you mean by using up all four of the drive slots in the mp?
I inserted a pcie card in pcie slot 3 because there are no external esata ports on my macpro and i needed one to connect an esata drive.
with regards to the pcie card itself i've pretty much given up on making it work as from looking at their site whilst they claim mac compatability it seems to have been something of an afterthought.
my problem is that im worried any pcie esata card i buy will conflict with my mac because i've been told that they mostly use the same generic si3132 drivers which caused the kernel panic.
Message was edited by: Henners2000

PCI card Hyper-v

I am using Hyper-v on a Windows server 2008 machine, with a linux machine running as a Hyper-v guest. I want to install a PCI card into this linux machine. How do I do it? Please help asap.
pf

I am using Hyper-v on a Windows server 2008 machine, with a linux machine running as a Hyper-v guest. I want to install a PCI card into this linux machine. How do I do it? Please help asap.
pf
If your PCI card is actually a PCIe card and it's a) network and b) does support SR-IOV (Single Root I/O Virtualization) you can do this. See:
Overview of Single Root I/O Virtualization (SR-IOV)
http://msdn.microsoft.com/en-us/library/windows/hardware/hh440148(v=vs.85).aspx
Everything you wanted to know
about SR-IOV in Hyper-V
http://blogs.technet.com/b/jhoward/archive/2012/03/12/everything-you-wanted-to-know-about-sr-iov-in-hyper-v-part-1.aspx
Windows
Server 2012 Hyper-V and SR-IOV
http://blogs.technet.com/b/matthts/archive/2012/10/13/windows-server-2012-hyper-v-and-sr-iov.aspx
Hope this helped a bit :)
StarWind VSAN [Virtual SAN] clusters Hyper-V without SAS, Fibre Channel, SMB 3.0 or iSCSI, uses Ethernet to mirror internally mounted SATA disks between hosts.

I can't find my PCI card using Measurement and Automation Explorer

I've installed the PCI card.. It's a PCI-DAS08. The PC I'm running is quite slow, took like an hour to install Labview. The Measurement and Automation Explorer can't seem to find the card even though it's shown in the Device Manager. I don't know how to solve this problem. Any help or tips appreciated. THANKS

Is tha device made by NI?
MAX only supports NI DAQ devices.
You will need the drivers and support software from the equipment manufactuer.
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Using a PCI card INTERNAL USB port

Hello to anyone reading this !
I've just installed a PCI card in my G5 in order to add more USB ports. When I started searching for one, i was surprised to see most had an internal port, I couldn't really see the use of that. A friend told me it can be used on PCs to plug an extension towards a free port in front of the main unit.
Considering i can't do this on my G5, I was wondering how to take advantage of this internal port and I'd like to know if I can plug my USB Bluetooth adapter, as it doens't need to be visible and it would free one of my external ports. The question is, are there some security restrictions regarding what you put INSIDE the unit? Isn't it too hot inside to leave the bluetooth key or anything else that is not designed to be inside?
Does anyone have any advice?
Thanks in advance
iVince

With all the airflow in a G5, I don't think heat will be a problem, but a Bluetooth unit probably will not be useful inside a shielded metal case. The Apple Bluetooth card connects to an antenna wire that goes outside the shielded section, but I don't think there is any way to connect that wire to the USB Bluetooth module.

Mezzanine cards vs pci card

hi all
what are the differences between mezzanine card and pci card
in mean of speed, arcitecture, features supported etc
thanking you in advance

You wouldn't see any difference in speed. Installing a PCI card would just be duplicating the built-in ethernet and isn't necessary unless your networking setup needs two installed NIC's.

Motu pcie card

Installed the pci card into my mac but it doesnt seem to be recognised any suggestions?
Ive put it in slot 1 and 4
There is a pci bridge showing up on slot 4
Thxs

Try the following
Applications>Utilities> Audio Midi Setup

D-link ethernet PCI card and "broken" driver

Hello!
I found a D-link DFE-530+ ethernet PCI adapter card at a local target on clearance for under $10 - so I figured that despite the "Windows" requirement, I'd give it a try on my 400mhz, "Sawtooth" AGP graphics G4. The D-link website for the card says that the card is compatible with Mac OS 10.2+, and has a driver for download. I downloaed the driver and installed it, then installed the PCI card. No luck, Tiger (running on the G4) complains that the "extension" is bad and that I need to uninstall it or download a newer version of the driver - that doesn't exist.
What can I do to make it work, and does a third-party driver exist?
Thanks,
-Dan

I didn't try it before installing the D-link drivers, no, but the card isn't even recognized when the D-Link drivers don't load. I'll uninstall the driver and see what happens - I suppose it couldn't hurt!
Thanks,
-Dan

Problem about D-link card installation on Solaris 8 intel

hello,
I don't know how to install my ethernet card on the Solaris 8 intel.
It's a D-link DFE-530TX model on PCI bus.
Could you send my the methode to install it.
Thank you very much.

Hi,
refer this URL http://sun.drydog.com/faq/s86faq.html.
(Note: question - 6.7)
revert back.
Thanks.
regards,
senthilkumar
SUN - DTS

How to install oracle 9i report server on sun sparc 280 system

hello to all
may i get any help to install report server on the sun sparc 280 R system which is running oracle 9i database,forms and reports
thanks in adv.
Mohan

hello,
what kind of information are you looing for abve and beyond whats documented in the install guide for the particular platforms.
thanks,
ph.

Pl. help me install a PCI card in a solaris 2.6 system

Similar Messages

Maybe you are looking for