Place call to meet-me number fails

Hi All,
I'm hitting a weird issue with trying to place a call from uccx to a meet-me number.
Uccx will place the call and you do hear the party entrance tone but it never plays the prompt. After the timeout on the place call step it goes to the unsuccessful branch and fails.
Same happens with a consult transfer.
I've checked codecs and CSS/partitions so I'm 99% sure it's not that.
Looking in the logs the reason is the call state is active.
Uccx version 9.0.2
Cucm version 9.1.2
Has anyone seem this before and got it working?
Thanks Gus.

Hi Gus-
I have been working with TAC on a similar issue since September. This worked with CUCM 8.5.1.14900-5 / UCCX 9.0.2.10000-71 and stopped working when CUCM was upgraded to 9.1.2.10000-28.
If you use the same script and send the call to a DN on a phone is the call successful?
Have you tried using a Call Redirect step and sending the call to the MeetMe number? (this is my current workaround)
Could you pull the MIVR logs from your 7.x cluster and see if the Destination message (bolded and underlined below) shows as Unknown or if it is something different?
From TAC:
UCCX Engine logs:
//CallCtlConnEstablishedEv is fired:
19893: Sep 27 15:40:46.458 CDT %MIVR-SS_TEL-7-UNK:CallID:9 MediaId:34141/1
Task:27000000014, Local CallCtlConnEstablishedEv [1785:allinternal:1/(P1-jtapiuser_1)
GCID=(1,34141)->ACTIVE]->ESTABLISHED
//The Destination for the connection is unknown:null
19901: Sep 27 15:40:46.464 CDT %MIVR-SS_TEL-7-UNK:snum = 1785, addr.getName = Unknown
19909: Sep 27 15:40:46.483 CDT %MIVR-SS_TEL-7-UNK:CallID:9 MediaId:34141/1
Task:27000000014, Connection to new destination CREATED, new dest: Unknown
//UCCX tries to reach the destination but is not able to as the destination is unknown/null:
19967: Sep 27 15:40:56.453 CDT %MIVR-SS_TEL-7-UNK:CallID:9 MediaId:34141/1
Task:27000000014 did not get destination CONN_ESTABLISHED nor CONN_FAILED event
19968: Sep 27 15:40:56.454 CDT
%MIVR-SS_TEL-7-UNK:Call.rejecting(RESOURCE_NOT_ACKNOWLEDGING)
JTAPICallContact[id=9,type=Cisco JTAPI
Call,implId=34141/1,active=true,state=CALL_INITIATED,inbound=false,handled=false,locale=en
_US,aborting=false,app=App[name=meetMe,type=Cisco Script
Application,id=2,desc=meetMe,enabled=true,max=10,valid=true,cfg=[ApplicationConfig[schema=
ApplicationConfig,time=2013-09-27
14:36:45.0,recordId=57,desc=meetMe,name=meetMe,type=Cisco Script
Application,id=2,enabled=true,sessions=10,script=SCRIPT[meetMeAuthentication-Rev01-test.ae
f],defaultScript=,vars=[],defaultVars=null]]],task=27000000014,session=Session[id=001-0x95
02f9009,parent=null,active=true,state=SESSION_IN_USE,time=1380314446448],seqNum=0,time=138
0314446446,cn=2019,dn=null,cgn=1785,ani=null,dnis=null,clid=null,atype=OUTBOUND,lrd=null,o
cn=2019,odn=null,uui=null,aniii=null,ced=null,OrigProtocolCallRef=null,DestProtocolCallRef
=000000000000855D020F50CF00000000,route=RP[num=0000],port=TP[type=Cisco CTI
Port,id=3,implId=1785,active=true,state=IN_USE],aborting=false,transferring=false,disconne
cting=false]
//Hence, the call is dropped
19969: Sep 27 15:40:56.454 CDT %MIVR-SS_TEL-7-UNK:CallID:9 MediaId:34141/1, dropping the
call, ciscoCall state is ACTIVE
Thanks,
DJ

Similar Messages

We have a 5s active on our account. After turning on a previously active 4s (it had the same number) The 5s can no longer place call and when you call it from another phone the 4s rings, but will not pick up. Texting over the cell networks works fine.

We have a 5s active on our account. After turning on a previously active 4s (it had the same number) The 5s can no longer place call and when you call it from another phone the 4s rings, but will not pick up. Texting over the cell networks works fine. Any suggestions??

hens0861,
Hmm, let's ensure this is working as it should be! So what phone should be active on your account? Did you switch the devices online or how to did you activate the 5s? Please share details.
KarenC_VZW
Follow us on Twitter @VZWSupport

Place Call to Internal Number

Hello,
I am a relatively new user of IPCC Express. I am working on a script using the CRS Editor that, when a call comes in, the system will place a call to an internal number and play a prompt to the called number. It currently comes up as unsuccessful when I test it. The script is very small right now as I am just trying to make it complete the call before I add the intricacies.
I have attached both the script and a screen shot of the script.
Thank you in advance,
Matt

Just as you said, I removed the Accept step and ran the debugger. It doesn't return any exceptions, it runs right through. When I run the reactive debug (with the Accept step reinserted), it hits unsuccessful when it tries to place the call.

I have lost facetime on my macbook pro. Calls ring but message says fail

I have lost facetime on my macbook pro. I place the call, it rings then says 'failed'. Has been working very well until now. Any ideas anyone? Thanks.

Hello lindseynicola,
Thanks for using Apple Support Communities.
I understand that you're having issues with making calls using FaceTime on your Mac. I'd like you to take a look at the following troubleshooting information, in order to get this issue resolved:
Troubleshooting FaceTime for Mac
You can make FaceTime calls using the FaceTime app. You can call FaceTime users whose contact information is in Contacts. You can add contacts and edit contact information in either FaceTime or Contacts. To place a video call, you may use a phone number or email address.
If you encounter issues making or receiving FaceTime calls, try the following:
Verify that FaceTime is enabled in FaceTime > Preferences.If the issue persists, or if you see the message "Waiting for Activation", try toggling FaceTime off and then on.
Verify that the Date, Time, and Time Zone are set correctly:From the Apple () menu, choose System Preferences > Date & Time > Date & Time.
Enable "Set Automatically".
Click the Time Zone tab and confirm the closest city is correct.
Verify that both parties are connected to an active broadband Internet connection.
See Mac OS X: Troubleshooting a cable modem, DSL, or LAN Internet connection.
Consult Using FaceTime behind a firewall for necessary ports to open in firewalls, security software and routers.
If you encounter issues using a Wi-Fi network, use standard Wi-Fi network troubleshooting to resolve interference and other issues.
Verify the phone number or email address being used is the correct one activated for FaceTime.You can verify that you are using a valid Apple ID at appleid.apple.com. You can also create an Apple ID or reset your password from this website.
Verify that both parties have installed the latest software updates for their Mac and/or device. See:
Mac OS X: Updating your software
iOS: How to update your iPhone, iPad, or iPod touch
FaceTime for Mac: Troubleshooting FaceTime
http://support.apple.com/kb/TS4185
Take care,
Alex H.

Script,Place call

Hi,when i use the place the call step in the script editor,and the collected string matches an internal number,the place call step rings the destination but as soon as i answer the call,the call does not get really connected and the reactive debug shows that the call goes to the end and i hear an auto generated error message.
lets say phone 2001 call to uccx and then he dialed the extension 2002,the place call step sends the call to 2002,but i see on the phone screens From CTI port 1700 and on the other phone to CTI port 1701,i don't see from 2001 to 2002.
If i use the call redirect step,then i see from 2001 to 2002 and the call works normally.I just can't use the call redirect cause there is no (no answer option) under it .So if the called number didn't answer within 10 sec ,with the call redirect i can't take an action but with the place the call step,i can.
Help will be so appreciated.
Thanks in advance.

As always excpected,you are very helpful.
Thanks man.call consult transfer works,but i have two questions:
1-why did the call fail when i use the place call step ?
2- In the consult transfer step,what are the "output digits" field for?
i used a string variable just to fill the fields,but i didn't see any digits in it when i used the debug !
Thanks in advance.

Place Call and continue with remaining script steps - is it possible?

We recently picked up IPCelerate which has the ability to send a Text display or Text-to-Speech message to a group of phones simply by dialing a configured directory number. We would like to text our call center agents with this application when a caller has been waiting for X number of loops.
Attempting to use 'Place Call' to initiate this text page works, however, the script terminates immediately after the call is placed and we would like to continue on with the remainder of our script. In this case, on Success go back to the top of the loop.
I have also tried to use Call Subflow instead, thinking an executed sub-routine placing the call would return to the original script and continue on, but it didn't. In both cases, the system comes back and states " I'm sorry, we're currently experiencing system problems and are unable to process your call. Please try again later."
If there's a way to get this to work via Place Call or another process to accomplish the same result, that would be fantastic. I appreciate any feedback.
We're using UCCx Express 5.0 (2.064) with premium type licensing.

Hello,
I did get to an answer similar to what r.stockton did to solve the issue, but I left Exception (ContactInactiveException) Goto in ours to isolate exceptions because we have multiple contacts within our script. Turns out that this particular exception was thrown by the PlaceCall step ending abruptly by our paging system answering and hanging up the call quickly. MIVR logs showed that it didn't bomb as immediately as when the debugs showed it crashing - it actually went into a loop over and over with the Trigger contact before failing.
We had some help from TAC on this, but below is what we did to keep some error checking and notification we use available to us. We are running a check to make sure the Call Trigger (original call) is still active.
placecallContact = Place Call (to Number)
on Exception (ContactInactiveException) Goto
label:
CallActive = Get Contact Info (--Trigering Contact--, Active)
If (CallActive) Then
- True branch continues with script
- False Branch terminates call
If this takes the false branch, it means the trigger contact is not active, and has abandoned the call or been transferred elsewhere. Placed an End step here to prevent any loops.
If this takes the true branch, it means the triggering contact is actually still active. In our scenario, CallActive (boolean variable) is verified true and continues with the script without going into the loop of death.
I hope this helps!

My Phone Cannot Place Calls or Receive them

This is the Second Time this Problem has Happened. Each Time followed a Plane Trip from Detroit to Kansas City MO. The Phone Was Turned OFF while on the plane both times. I can Text and Receive DATA ONLY! Any call Place results with a message "The Number is Not in Service". I received a Text that when someone Calls My Phone they hear "All Circuits are Busy".
I DEPEND on This PHONE for My Business! I DO NOT HAVE TIME FOR THIS ISSUE TO KEEP HAPPENING!!!! The Verizon Techs CANNOT FIGURE IT OUT. They All want to Change the SIM Card. That was done the First Time (3 Weeks Ago) and Again When i Returned Home. At That Point I Could Place Calls, But No One Could HEAR ME! Come to find out, the phone had Switched to 4GLTE Only. If i had Less than That Coverage, My Phone Could Not Transmit My Voice!
I am at the End of my Patience With this PHONE. I had a Droid 4 and it was Fine (I Still Have It and am about to put it Back Into Service). I was talked Into this Piece of JUNK by a Pushy Verizon Twit in Toledo that would not Respond to me When I had Issues with the Turbo Set Up. I called her number when I had an issue and she Never Responded. I had to figure it out on my own and waste a bunch of time in doing so.
I Need RESULTS NOW, And What About this LOLIPOP 5.1 UPDATE I Keep Hearing About. Will That actually FIX This Thing or is it Just Another Verizon Buffer??!!
Back to the Original Issue; Is there a Problem with these phones Going Though X-RAY Machines At Airports?

Hello DanEvans442! I'm terribly sorry over any issues you've had with your Turbo. You and I have the same model. I love mine! One of the best devices have had in 10 years. I want that to be the same for you! You've mentioned that you've had issues after deboarding the plane. One of the things you'll want to be sure of is that the device isn't inadvertently in Airplane Mode. Please go to Settings> Airplane Mode. If it is set to "On", please turn it off and try your device again. If it was already set to off, then we can move to other possible contributors. Can you describe what happens when you try to use the service? DionM_VZW Follow us on Twitter www.twitter.com/vzwsupport

Script Outbound. How introduce multiple numbers in a "Place call"?

Hi,
i'm trying to implement a script to make multiple outbound calls in a UCCX system but i don't know how can introduce several phones. The idea is simple but this step is critical:
1-take the first phone number and make the call.
2-take the secornd phone number and make the call.
3-.........
Thanks for help.
Regards

Antonio,
You can do this by taking the phone numbers from an XML document or from a database query (if you have premium license). You will need the place call step and make a loop around it, so when the first number is succesfully dialed, the script take the next number and so on. When using a XML you need to create one, for example:
<?xml version="1.0" encoding="ISO-8859-1"?>
088909220
088909221
Save it as Customer.xml (for example) and upload it to the UCCX repository (Documents in this case).
Creating the script:
Example variables (name, type, value)
xmlDoc, Document, DOC[Customer.xml]
suffixInt, int, 0
suffixString, String, ""
numberToCall, String, ""
Customer, String, ""
calledContact, Contact, null
The script should be something like this:
Gabriel

Problem with Place call in a script with HTTP trigger

Hi!
I'm trying to develop a sample script, associated to an application that has an HTTP trigger. I'm working with UCCX Premium 8.5.1
The trigger is working OK, but the place call output is allways "unsuccessful". The number to call and the redirect number are extensions of the same IPT platform.
Below you will find print-screen of the script. Besides, I'm attaching the .aef file.
Any help would be appreciated. Thanks in advance.
Roy.

The value in your "Call Control Group" must match the "Group ID" in your CM Telephony Call Control Group Configuration
This is from my lab system so the "AgentsLoggedIn" variable would need to contain 1 or 3. You are telling the script which CTI port group to make the call with. You have a 0 in your AgentsLoggedIn so do you have a Group ID of 0?
Your CTI group must be able to make the call so must have the correct partition/Calling Search Space
Graham

Supress Place call popup in CIC0

Hi all,
In Tcode CIC0,After selecting the Business partner ,after that click on place call,it will show a pop up with telephone no.s
I want to supress the Pop up when Business partner has more than one phone number.
Is there any BADI or Exits available to achieve this functionality.
Thanks

Hi Ashish,
that´s strange - because in our system it worked that way.
Since some months we do not use the transaction launcher for SAP GUI transactions at all.
We installed a consulting solution from innovate which allows to launch the real SAP GUI in the CRM webclient UI and to pass easily all parameters which are needed.
This has the advantages:
- much better performance as a launch transaction
- real SAP GUI is known by our users - the transaction launcher looks different (e.g. buttons)
- for some transactions there was missing functionality in the launch transaction which is there in SAP GUI
- No trouble with ZTransactions in SAP GUI
It was only one day efford to install this Add-on from innovate and to get the knowledge how to use it.
If you want to have more information i will give you the contact person at innovate gmbh.
Best regards
Manfred

Cannot place calls after 2.2 update

Today I downloaded and installed the iTunes update, then did the iPhone 2.2 update. Now I cannot place calls with my phone. I can receive calls and all other functions work ok.
I powered off and restarted the phone. No luck.
I reset the phone. No luck.
I went to AT&T and had my SIM card replaced. No luck.
I restored the phone to factory settings. No luck.
I restored the phone from my last backup. No luck.
Any suggestions?
Thanks!

3G
When I press the green Call button it immediately says the call failed.
AT&T verified that my account was in good standing and had no billing/administrative issues. They then replaced my SIM card. Honestly, I didn't trust the AT&T store to do tech-support on the iPhone. Since there was an Apple store about 100 yards away, I went there next.
At the Genius Bar, the man said that there had been some "voltage issues" from updating via a laptop. He said that I should restore it to factory settings, then try again, but this time from a desktop. I tried that, but still, no luck.
It seems odd that I can receive calls, but not place them.

Hello, I have been unable to activate my new iphone 6. When I call the activation phone number it just says terms and conditions have been accepted on this account. Please help.

I have been unable to activate my new iphone 6. When I call the activation phone number it just says terms and conditions have been accepted on this account. Please help.

Same thing here. I love how they include this nice and easy to follow guide in the box and the KEY step for activation (the phone call) is a total fail. To verizon: the automated just says Terms and Conditions have been accepted for this number. Press 1 to enter another phone number in the order. Well, I HAD NO other phone number in my order. The message gives no other options. She repeats the same line 3 more times and after the 3rd time, it says please hold while we transfer you, call may be monitored etc. Guess what, its 2 am ET and customer service is closed?
Do you guys expect thousands of iphone customers to speak to a CSR just to activate? Why not just let us do it online? I have activated plenty of phones even LTE phones, online. Now I'm going to have to compete with the other 30,000 people who ran into this same problem overnight tomorrow on the phone....

When running labview's test executive I recieve runtime error: Call to step "PRE-RUN" failed. Could someone explain this error?

I have a set of vi's that work when run under labview. However, when calling these vi's from labview's test executive I recieve runtime error: Call to step "PRE-RUN" failed. in Assign Connector Pane.vi->Call Test.vi->Execute Pre-Run.vi->Test Executive. Could someone explain this error to me? (or ideally tell me how to fix it?) Thanks.

Hello,
There are any number of possible causes to this problem. Which version of Test Executive are you using? Have you upgraded your Test Executive recently? The latest version is 5.1.1. If you have changed anything about Test Executive on your computer recently, I recommend you perform a mass compile of all your VI libraries, as having different versions of the VIs on your system could often result in the "Call to Step XYZ Failed" errors. Also, are you using any DAQ or Analysis VIs in your steps? We have seen problems where the use of DAQ or Analysis VIs in the sequence can cause intermittent "Call to Step...Failed" errors. There are some KnowledgeBase entries on our website that discuss this problem. Are you using the Test Executive in the VI environment, or
as an executable? Again, there are some problems with using Test Executive as an executable that result in these errors, and there are also KnowledgeBase entries that discuss these problems.
If you have a pared-down application that demonstrates the problem, feel free to send me your VIs and your .seq file and I will try to reproduce the problem.
Alternatively, I would suggest you visit www.ni.com/teststand to learn about TestStand, our state-of-the-art Test Sequencing software that completely outperforms Test Executive. It is very easy to use and much more powerful, and we have a top-notch support team available dedicated exclusively to supporting TestStand. As you are probably aware, we are no longer developing Test Executive, and instead are concentrating our efforts on making TestStand the penultimate solution for all our customers' test sequencing needs.
I appreciate your patience on this issue. Please let me know if I can offer further assistance.
Have a pleasant weeken
d.
Sincerely,
Darren Nattinger
Applications Engineer
National Instruments
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

CUPC not able to place call

Hi!
I've a CUCM 8.5.1 and CUPS 8.0.2. I'm a newbie to this thing. I did the configurations with reference from the book. The only problem I have right now is that I'm unable to make a phone call through the CUPC. CUPC is using 7.1. Is this a compatibility issue or something?
Regards,
Nita
Nita

Arni,
The reason the "Place Call" button is not available can be for a few reasons.
1) The number for User1 does not exist in Active Directory. This is where CUPC pulls numbers from for users on the buddy list.
2) As Rahul has suggested it would be wise to look further into your desk phone or soft phone control. I cant see behind the menu to determine which mode you are in, but there's a good chance that the soft phone or desk phone is not connected properly. You can click on the phone icon in the upper right hand corner of the screen and determine what is selected (either desk oh soft phone (phone on computer). Specifically you can check under Help -> Show server health and ensure there is not ! marks on desk phone or soft phone.
If you can provide further information we can troubleshoot further.
Regards,
Jason

Not able to call on any mobile number even credit ...

not able to call on any mobile number even credit is there in account

Hi,
Please check your usage call history on your Skype web account page to learn why the calls failed: www.skype.com/go/myaccount
Follow the latest Skype Community News
↓ Did my reply answer your question? Accept it as a solution to help others, Thanks. ↓

Place call to meet-me number fails

Similar Messages

Maybe you are looking for