Platform Cable USB II Stopped Working

Hi all,
I have successfully been using the Platform Cable USB II to program a Spartan 6 for around 6 month. Today I tried to load a new program and I could not connect to the cable. See below for the message iMPACT gives me. When I came in to use ISE and iMPACT today ISE said my license was no longer valid; I pointed ISE to the license file I had always been using (located in C:\Xilinx) and ISE stopped complaining. AS far as know nothing else in my system has changed since the last time I programmed the Spartan 6. The Platform cable light is green and Windows recognizes the cable just fine. I am using Windows 7 and ISE 13.4 (nt64). I have checked other posts and it seems this is not a new issue, but I was unable to fix the problem by following any of those suggestions. Please help! Thanks,
Aaron
AutoDetecting cable. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_emb.sys found.
Driver version: src=1029, dest=1029.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Invalid device driver license.
Cable connection failed.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
Driver windrvr6.sys version = 11.6.0.0. WinDriver v11.6.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Jun 9 2014 x86_64 64bit SYS 10:03:05, version = 1160.
Cable connection failed.
PROGRESS_END - End Operation.
Elapsed time = 32 sec.
Cable autodetection failed.
WARNING:iMPACT:923 - Can not find cable, check cable setup !

Thanks for the help. Very useful! I've done the uninstall -> install again. Unfortunately, it doesn't solve my problem. Cable is plugged in. Green light is on. Jungo windows driver appears in devices. But still error code 923. Grrr. Annoying!
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: no JTAG device was found.
AutoDetecting cable. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_xp2.sys found.
Driver version: src=2301, dest=2301.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Invalid device driver license.
Cable connection failed.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
Driver windrvr6.sys version = 11.7.0.0. WinDriver v11.7.0 Jungo Connectivity (c) 1997 - 2014 Build Date: Oct 26 2014 x86_64 64bit SYS 09:16:51, version = 1170.
Cable connection failed.
PROGRESS_END - End Operation.
Elapsed time = 2 sec.
Cable autodetection failed.
WARNING:iMPACT:923 - Can not find cable, check cable setup !

Similar Messages

1 of 2 USB ports stopped working after 10.7.2 upgrade

I have the newest Macbook Pro. I upgraded to 10.7.2 today and immediately after, 1 of my 2 usb ports stopped working.   Thought it may be the cable, so I switched cables. Tried plugging in my iPhone, my portable drive and nothing.   Both work on the other port though.   Both ports worked fine before the update.
I've rebooted 4x.
Suggestions?

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
If this does not help, contact Apple.
Genius Bar reservation
http://www.apple.com/retail/geniusbar/
Best.

Macbook pro USB ports stopped working

After downloading the new OS (and the updates), my USB ports have stopped working. I've tried a variety of resets (resetting the PRAM, GMC reset, resetting the computer, etc.). One of the USB ports would read the usb for a wireless mouse (and only that wireless mouse, no flash drives or ipod cables), but that stopped working as well.
What else is there to do? The system is only a year old. I've never had a problem concerning usb ports on other computers, especially after a software upgrade.
Any ideas?
Thanks

I have had a similar problem since upgrading to Lion 10.7.3. I have a MacPro and all was going well. However, now I have huge problems with my USB ports. Some are recognized some of the time if I unplug then replug, but not in a reliable manner. This applies to USB ports at both the front and back of my computer. My printer won't work or my mouse won't work (but at times I can get one or the other), but any external USB drives (including camera's) and my iPhone are not recognized. Obviously very frustrating. Other issues that seem to have occured are recognition of Outlook for Mac, so have reverted to MacMail (not as good, but working).
Looking through a variety of threads, this issue isn't that new going back to at least July of 2011 (http://www.mac-forums.com/forums/os-x-operating-system/245665-os-x-lion-will-not -read-external-hard-drives-usb-flash-drives.html).
I am also involved in long-running saga with "upgrade" from MobileMe to iCloud that has led to many individuals (including myself) losing "push" email capability despite 9 months and 35 pages worth of problems on the Apple Support site (https://discussions.apple.com/message/18033340?ac_cid=142432#18033340).
Having been an Apple user since 1988 it is ironic that as it becomes more popular it becomes increasingly less reliable.
Does anyone have any solutions for the USB problem that are reliable?

USB ethernet stopped working on 10.7.4.

After I upgraded to 10.7.4, the usb ethernet stopped working. When I plugin the usb ethernet port, it still shows "Cable Unplugged". Any suggestions? Thanks.

FIxed my problem!
After years the problem was solved somply!
Go to System preferences
Go to Ethernet
Go to Advance
Go to Hardware
The just make the changes like in the pictures below

Xilinx Platform Cable USB II Status Light Always Off

I have been using the Xilinx Platform Cable USB II with ISE WebPACK 10.1 on Windows XP for a couple of years now.
Last week I bought a second Xilinx Platform cable, but I have not been able to get it to work. I have followed the instructions in the installation guide (ug344), and the Windows Found New Hardware Wizard runs twice when the cable is plugged in to a USB port, as expected. The wizard indicates that the installation of the firmware loader and the cable are successful. However, the status light on the cable never turns on. Also, the Cable Auto Connect operation in iMPACT fails:
Welcome to iMPACT
iMPACT Version: 10.1.03
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
GUI --- Auto connect to cable...
// *** BATCH CMD : setCable -port auto
AutoDetecting cable. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
LPT base address = 0378h.
ECP base address = FFFFFFFFh.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable connection failed.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusb_xp2.sys found.
Driver version: src=2301, dest=2301.
Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
Cable PID = 0008.
Max current requested during enumeration is 300 mA.
Type = 0x0005.
write (count, cmdBuffer, dataBuffer) failed C0000004.
Cable Type = 3, Revision = 0.
Setting cable speed to 6 MHz.
Cable connection established.
Firmware version = 2301.
File version of C:/Xilinx/10.1/ISE/data/xusb_xp2.hex = 2401.
Firmware hex file version = 2401.
Downloading C:/Xilinx/10.1/ISE/data/xusb_xp2.hex.
Downloaded firmware version = 2401.
Done pin is low. Cable will be updated.
Done pin is low. Current retry count = 0.
Updating the cable fpga firmware...
PROGRESS_START - Starting Operation.
ERROR:iMPACT:2358 - Firmware update failed.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Done pin is low. Current retry count = 1.
Updating the cable fpga firmware...
PROGRESS_START - Starting Operation.
ERROR:iMPACT:2358 - Firmware update failed.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Done pin is low. Current retry count = 2.
Updating the cable fpga firmware...
PROGRESS_START - Starting Operation.
ERROR:iMPACT:2358 - Firmware update failed.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
Done pin is low. Current retry count = 3.
Error updating cable firmware.
I have tried using the cable with the latest version of ISE WepPACK on a computer running Windows 7, and I have followed instructions to uninstall and reinstall the cable drivers using a DOS command prompt. The cable behaves as described above.
Is there anything else I can try, or is the state of the status light an indication that there is hardware problem?
Thanks.

Correct. Even though iMPACT reports it is attempting to install firmware, the light is never on. I have not seen it on in any color since I bought the cable.
I have tried the latest version. I have a newer machine running Windows 7 with ISE WebPACK 14.7. Again, the drivers seem to install witouth a problem, but the light remains off. Here is the log when I attempt to connect to the cable:
Welcome to iMPACT
iMPACT Version: 14.7
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
GUI --- Auto connect to cable...
// *** BATCH CMD : setCable -port auto
INFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: no JTAG device was found.
AutoDetecting cable. Please wait.
*** WARNING ***: When port is set to auto detect mode, cable speed is set to default 6 MHz regardless of explicit arguments supplied for setting the baud rates
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Driver file xusbdfwu.sys found.
Driver version: src=1027, dest=1027.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable PID = 0008.
Max current requested during enumeration is 300 mA.
Type = 0x0005.
write (count, cmdBuffer, dataBuffer) failed C0000004.
Cable Type = 3, Revision = 0.
Setting cable speed to 6 MHz.
write cmdbuffer failed 20000015.
Error reading reference voltage level.
Cable connection failed.
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable connection failed.
Connecting to cable (Parallel Port - LPT2).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
Cable connection failed.
PROGRESS_END - End Operation.
Elapsed time = 4 sec.
Cable autodetection failed.
Thanks.

HP Pavilion dv6 All 4 USB ports stopped working

Hello,
I recently bought a Pavilion dv6-6c11sa laptop. Windows 7 Home Premium 64-bit
Everything was working fine for about a week, and then yesterday all of the USB ports stopped working. I have 4 USB ports in total, two 2.0 and two 3.0. No matter what peripheral device I plug in, mouse or flash drive etc, they're not recognized by the laptop. The lights don't even light up on the devices, regardless of the port. I've tried uninstalling and reinstalling the drivers in device manager, taking out the battery and rebooting, installing the chipset drivers (AMD), nothing works. No programs had been installed 3 days prior to the occurence, although I had rebooted several times in that time frame. I simply booted up the laptop yesterday, and nothing worked.
Could anyone offer a solution or suggestion, please?

Hello,
I recently bought a Pavilion dv6-6c11sa laptop. Windows 7 Home Premium 64-bit
Everything was working fine for about a week, and then yesterday all of the USB ports stopped working. I have 4 USB ports in total, two 2.0 and two 3.0. No matter what peripheral device I plug in, mouse or flash drive etc, they're not recognized by the laptop. The lights don't even light up on the devices, regardless of the port. I've tried uninstalling and reinstalling the drivers in device manager, taking out the battery and rebooting, installing the chipset drivers (AMD), nothing works. No programs had been installed 3 days prior to the occurence, although I had rebooted several times in that time frame. I simply booted up the laptop yesterday, and nothing worked.

Can't install netbeans 8 on windows 7 ultimate 32 bit (Java Platform SE binary has stopped working), problem event name : BEX

I can't install netbeans 8 on my windows 7 ultimate 32 bit. Please help me.. This is the error message :
Java Platform SE binary has stopped working
Problem signature:
Problem Event Name:   BEX
Application Name:   java.exe
Application Version:   8.0.5.13
Application Timestamp:   53280287
Fault Module Name:   StackHash_2264
Fault Module Version:   0.0.0.0
Fault Module Timestamp:   00000000
Exception Offset:   00000040
Exception Code:   c0000005
Exception Data:   00000008
OS Version:   6.1.7600.2.0.0.256.1
Locale ID:   1033
Additional Information 1:   2264
Additional Information 2:   2264db07e74365624c50317d7b856ae9
Additional Information 3:   875f
Additional Information 4:   875fa2ef9d2bdca96466e8af55d1ae6e
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt

1. I had similar problem and upgrade of BIOS has helped.
2. Try Oracle support forum if 1 does not help.
Rgds
Milos

USB Ethernet stop working after 10.7.5 update

After updated to 10.7.5, my usb ethernet stop working, and always shows it doesn't connect.
Reinstall 10.7.5 make no difference.
How do I solve it?
Thanks!
Yu-Hsuan

Or download it directly from ASIX Electronics instead of driversworld.us.
Product family: USB 2.0 to fast Ethernet
Product name: AX88772
URL: http://www.asix.com.tw/download.php?sub=downloadsearch&PSNoID=101
I installed it and my AppleUSBEthernet started to work.
The error i had (sudo dmesg):
AppleUSBEthernet::monitorLinkStatus - Link down, Device b470200
0 0 AppleUSBEthernet: monitorLinkStatus - Link partner register is bad, re-trying...
0 0 AppleUSBEthernet: monitorLinkStatus - Link partner register is bad, trying to reset...

A barcode scanner that was connected directly to the Mac's USB port stopped working as the "USB had too much power drawn", even though it has worked for over a year in that port. WHen we plugged it into the port on the keyboard, the device works. Why?

A barcode scanner that was connected directly to the Mac's USB port stopped working as the "USB had too much power drawn", even though it has worked for over a year in that port. When we plugged it into the port on the keyboard, the device works. Why? Obviously the device is operational. Could the USB port have burned out from having too much power drawn? If so, is it reparable?

It can't draw "too much" power, it can only draw as much as the USB port is able to provide and no more. IIRC, the keyboard port has a lower power output than the iMac's port.
That being said, yea, it's possible that the port has failed and it can be replaced or if another port works you can use that one. Although if it is still under warranty or covered by Apple Care, then I would take it to an Apple Store or service provider to get the port repaired.

LiveCycle Workbench ES2 - "Java(TM) Platform SE binary has stopped working" Error

Hi,
I am getting this error when I try to create a new process o open an existing process.
"Java(TM) Platform SE binary has stopped working"
The only option is to click on a "Close" button and end the LC Workbench ES2 program.
Also, when I try to open an existing form, it displays 'garbage' - a screenfull of control unrecognizable characters - instead of the form itself.
When this error comes up, I also get a pop-up window with a list of log entries / errors (please see attached: Java Platform SE binary has stopped working.jpg)
Environment:
Windows Vista Ultimate running on HP Desktop (e9107c Intel CORE 2 Quad Processor withy 8 GB RAM, 750GB HDD)
Downloaded and installed the Trial Version of LiveCycle ES2 package (Windows JBoss version)
The LiveCycle ES2 server is installed properly and is working with the following services. Are there any missing services?
LiveCycle Output ES2, LiveCycle Rights Management ES2, LiveCycle PDF Generator ES2 Evaluation, LiveCycle Process Management ES2, LiveCycle Workspace ES2, Applications and Services, LiveCycle ContentServices ES2, LiveCycle Forms ES2
I already had Adobe Acrobat Pro Extended 9.2 and the associated LiveCycle Designer instaleld prior to installing the Trial of LC ES2.
Basesd on the installation insttructions, I deleted the Designer ES from my Acrobat Pro Extended and instaleld the LC Workbench ES2.
Now I don't see a seprate entry for the LC Designer ES2 anymore on my Start >> Programs.
And th newly installed LC Workbench is not working
Any help in making the workbench 'work' is greatly appreciated.
Are there any tests we can do to troubleshoot this?
Thanks.

Here is some additional information that may be helpful in identifying the cause for this problem.
Here is the Exact ERROR :
Java (TM) Platform SE binary has stopped working
A problem caused the program to stop working correctly.
Windows will close the program and notify you if a solution is available.
Button: "Close Program".
On clicking that button, the error window goes away; the main LC WB ES2 program also closes; but a long error window appears. The full screenshot was attached in my original message. The top few lines are reproduced below.
JVMterminated. Exit code=255
C:\Program Files (x86)\Adobe\AdobeLiveCycleWorkbench ES2\workbench\jre\javaw.exe
-Xms128m
-Xmx512m
-XX:PermSize=256m
-XX:MinHeapFreeRatio=40
========Here is teh cutrrent status ===================
Adobe LiveCycle Designer ES2 is working properly: Good
Adobe LiveCycle Workbench ES2 has ONE problem
1. Program Starts properly
2. I am able to login to the LCES2 server
3. I am able to Browse and select sample projects
4. I am ble to create an Application, a folder, and a Form
5. I am able to invoke the LC Designer ES2 from within Workbench (while creating a form)
6. I am able to "invoke" an existinmg sample process in a web browser (not within workbench environment)
The main problem is...
I am NOT able to create a new process or open existing process using workbench.
Since it gives Java Platform SE error, I checked the versions of various Java Run Time Environments on my pc.
Properties of javaw.exe in different folders:
1. My Computer's JRE (common to all apps)
Folder: Program Files\Java\jre6\bin\
File Name: javaw.exe: Java Platform SE Binary
Version: 6.0.170.4
2. Adobe LiveCycleWorkbench ES2
Folder: Program Files (x86)\Adobe\Adobe LiveCycleWorkbench ES2\jre\bin\
File Name: javaw.exe: Java Platform SE Binary
Version: 6.0.20.6
2.1 Adobe LiveCycleDesigner ES2
Folder: Program Files (x86)\Adobe\Adobe LiveCycleWorkbench ES2\LiveCycleDesigner ES2\jre\bin\
File Name: javaw.exe: Java Platform SE Binary
Version: 6.0.140.6
2.2 workbench
Folder: Program Files (x86)\Adobe\Adobe LiveCycleWorkbench ES2\workbench\jre\bin\
File Name: javaw.exe: Java Platform SE Binary
Version: 6.0.70.6
I tried to use the same versions of JRE in all these folders; that didn't work..
I hope someone can throw more light on this and find the real cause.
Thanks a lot in advance!

USB Video stopped working with 3.1.8 update

I have been using iChat video with my USB camera for a while with the help of iChatUSBCam. The new update of iChat (3.1.8) included support for USB cameras and once installed my USB camera stopped working with iChat. It just reports the camera is in use by another application. I've been browsing for answers for a while and have tried many things:
- Restart in various combinations of unplugging and plugging in the camera
- Reinstalled the Macam driver
- Reinstalled Quicktime
- Uninstalled iChatUSBCam (since iChat is supposed to work without it now - I think...)
- Reinstalled iChatUSBCam (v 2.2.1 - current)
It's a Logitech Quickcam for Notebooks Deluxe. It continues to work fine with Skype and the the Macam camera tool. I'm using Skype for now (on tour for 6 weeks and use it to video call home) but the quality is crap compared to what iChat used to do.
Thanks for any help you can give.
Stranded in the UK with no decent video chat
Matthew
Powerbook 12" 1GHz - 1.25G RAM Mac OS X (10.4.9) Logitech Quickcam for Notebooks Deluxe

Some people have reported that Updating iChatUSBCam
and deleting the Macam drivers and then the
com.apple.ichat.plist is the way to go.
Thanks for your help!! I tried these things before, but tried them again in the order you suggested with no success. I'm pretty sure it is not a UVC compliant camera. It's not on Logitech's list of UVC cameras.
M/N: V-UBG35
P/N: 861228-0000
PID: CE6420A
If I try it without the Macam drivers it doesn't show up as a camera is connected at all.
It's so frustrating because it was working great with iChatUSBCam until the recent update. It still works in Skype with no problems, but I'd rather be using iChat if I can - much better video quality.
Thanks for any suggestions!
Matthew

Java Platform SE binary has stopped working

I have a strange problem with my system. If I have a jar or an applet running, then try to launch a second jar or applet, I get an error stating:
Java Platform SE binary has stopped working
Details:
Event: APPCRASH
Application: javaw.exe (or java.exe)
version: 6.0.260.3
timestamp: 4dc1160c
Fault Module: java.dll
Fault Version: 6.0.260.3
Fault TimeStamp: 4dc14bf1
Exception Code: c0000005
offset: 00004e2f
OS version: 6.1.7600.2.0.0.256.48
Locale ID: 1033
Additional 1: 1ec0
Additional 2: 1ec0fd70d07d06e5bfcf53c69ad1739
Additional 3: 2c48
Additional 4: 2c48940de5e7d1cb2e131ad6a0ca2feb
My system is a MACbook Pro running Windows 7 64-bit via bootcamp (yes, I'm booting into Windows). I have both java 32-bit and java 64-bit installed on my system. The executables are located in all the correct paths (I think) C:\Program Files, C:\Program Files (x86), and C:\Windows\System32. I've uninstalled and reinstalled all java versions multiple times and have tried executing the installer as the Admin (I have full admin rights). I also tried disabling the Symantec Endpoint protection during installation. A few other users in my company are also using the exact same system set up as I am; however, they are not having this problem. We are releasing a Netbeans based development tool to our customers very soon (it's out in Beta form now), so I really need to get this issue resolved. Does anyone have an idea on how to fix this?
Thank you!!

I have the same problem. I have un installed and installed java jre n jdk 6 and 7 versions multiple times. I am also runing win 7 64bit OS on macbook. I am getting this problem at the time of installation and running of both oracle OBIEE and jasper BI suits. Because of this error I tried installation of these products even after formatting my pc several times with brand new installation of BI products.

My USB webcam stopped working after I upgraded to OS X 10.6.8

When I installed the upgrade to OS X 10.6.8 my USB webcam stopped working.
Any idea how to get it back.

Upgraded from what to 10.6.8?
Did it work before?
What camera?

One usb port stopped working today

One of my USB ports stopped working today. I think it may be related to Itunes update today. Has anyone else seen this recently? I restarted my computer - but that didn't help. I have a MacBook Pro - running Lion 10.7.5
Any suggestions? I saw one USB Hub when I went to Apple --> About this Mac, but couldn't tell if both were there.

http://www.ehow.com/how_7351075_reset-usb-ports-mac-laptops.html

Brand new Macbook pro one USB port stopped working

Brand new Macbook Pro 15 with Retina display. One of the USB ports stopped working after 24hours.

Serial Port Configuration and Port definition is reset by
NVRAM http://support.apple.com/kb/ht1379
If no good I would return the machine ASAP:
Genius reservation http://www.apple.com/retail/geniusbar/
check warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

Platform Cable USB II Stopped Working

Similar Messages

Maybe you are looking for