Playback/Previewing Problems

The playback/preview button is not working on my Premiere Elements 7. I have tried hitting the button, the space bar and the full screen preview, but to no avail. What should I do?
Thanks

OK, you have Imported VOB, which mostly contain MPEG-2 AV files in the VOB container. Are all of your source files VOB's? Are these from a miniDVD camera? Which one, make/model? What is your Project Preset, and how did you Import the VOB's? Very likely something in there.
This ARTICLE will give you a bit more background on VOB's, and what they can contain.
Good luck, and thanks for the screen-cap, as it showed a lot.
Hunt

Similar Messages

RAM Preview Problems in After Effects CC

AE CS 6 RAM Previews work, but two problems to report with AE CC on the same computer. Possibly two faces of the same problem.
1. Having QuickTime Player open while doing a RAM preview makes the RAM preview stutter. I quit the player, and now the RAM preview plays back without dropping a frame, though Info palate shows "fps: 24 (realtime)", but the RAM preview playback is slow: ie, a tenor sounds like a baritone.
2. A RAM preview that looked and sounded fine last night, is now playing back slowly (tenor sounds like a baritone), though Info Palate shows "fps: 24 (realtime)". I have no other applications open. The only thing that changed is that I quit AE, slept the computer, slept a little myself, and then launched AE. Trashing the cache files (manually), rebooting, relaunching and re-RAM-previewing creates a functional RAM preview, so I assume there is some problem with the cached files or the retrieval of them.
Is anyone else getting either of these? If so, what is your system configuration?
Also, I posted on another thread that Quicktime import/render works with AE CS6 on this computer, but AE CC can not import, play, or render QT reliably (without throwing error messages). Perhaps all of this is part of the same problem.
Thoughts?
Cheers,
Benjamin
CS 6 CC | Mac OS 10.8.4 | MacPro5,1 | 96 GB Ram | PROJECT & MEDIA drive: Mercury Accelsior > 500 MB/s read/write | CACHE drive: Mercury Accelsior > 500 MB/s read/write | Nvidia Quadro 4000 Mac | CUDA Driver: latest update | Wacom Intuos 5

96 GB RAM is accessible in 10.8.4 on my machine according to OWC. I'm working on a stereoscopic 4K project with large files and hundreds of layers. I regurlarly render with AE MP while working with huge files in PS, and am glad to see the % of RAM AE uses displayed in my render cue between 3 and 60%.
I have 12 processors (24 with hyperthreading)
I have reserved 10 for other applications leaving 14 for After Effects
4 GB per x 14 = 56 GB for AE. leaving 40 GB for everything else
I've played with what and how much I have allocated being sure to keep the CPU counts even, but this does not fix the RAM preview problems described above. Any other suggestions?
Thanks,
Benjamin

CS4 Premiere Pro General file format & preview problems

I was redirected here after posting my complaint on Twitter, so please excuse my forum manner.
I've been using Adobe Premiere Pro (CS4) for about a year now, and I've been editing videos along with other packages with no problem. (Only problem being my slow processor). Up until last week Premiere Pro has been completely fine. But seeing I have a project deadline next month, I thought I would spend a day trying to kick-start the video editing.
My source videos were originally photograph-frames animated in Flash CS4 into .MOV, decided to use the H.264 output codec. As I have finished exporting my needed videos, I imported them into Premiere Pro as usual, as I have in the past. But then I encountered the common problem that I have seen quite a few have also encountered with .MOV, or jsut general "no-preview" problem when the source video is fine.
I then took a day to research online about Premiere Pro's compatability with .MOV, among other container and formats. Upon using softwares such as MediaInfo and GSpot, I found that there might have been a problem with missing Codecs within my Adobe package. I then tried to convert the .MOV into .MPG (mpeg2), hoping such standard codec would work with Premiere Pro as they they in the past. No result avail.
I then turned to the uninstall route (retaining user info) and re-installing. The problem has NOT been fixed, what's more is that it crashes almost instantly after I try rendering the workplace. (Even post-rendering does not show the preview, but the files in the Adobe folder, does). Here's a screencap to my latest workplace, if it helps:
[IMG]http://i86.photobucket.com/albums/k83/neo0031/AdobePreProcap.jpg[/IMG]
Before the re-install, I believe I was running Premiere Pro CS4's latest update (4.2.x) something, now it is back to 4.0.0. But I don't think that is where the main problem is? I recently changed my locale from a certain language to Japanese to run a certain program. Would that be causing the problem(s)?
Does anyone know a way that I can FIX this? Any help is appreciated and I thank you all in advance.
I am using a Sony Vaio NS series laptop,
a 2.0 GHz Intel Pentium Dual Core processor
3GB RAM,
intergrated graphics Intel Chipset Family Series 4( I think).
Windows Vista Home Premium 32bit.
I tried moving the Scratch disks from an external portable hard drive to the local hard drive, to no result.
Again, any help is appreciated. I would appreciate direct advice rather than links. Thanks again.
Neo.

I have updated my CS4, Ppro to 4.2.1. The problem still remains. Would it have anything to do with my project setting? I don't have much knowledge to setting one up. The difference between the AVC projects and etc?
EDIT : I took the problem to my lecturer, and he didn't do anything out of the ordinary, but his "magic touch" click on the preview panel (Main composition) has made the video show up! But even after render, it won't play. But scrubbing along frames is now fixed. Any idea what's causing the no-preview-playback?

Imovie HD skipping during playback/preview

HELP! I'm editing a 32 GB movie in iMovie HD, During simple Playbacks / previews the movie is skipping and becomes impossible to view, (unless I scroll the timeline)
I'm working w/ a brand new G4 ibook w/ 512 and 60GB HD totally dedicated to this project.(this problem has beome progressively worse as the file gets bigger) Is it HD space I'm lacking or Power or memory? I'm prepared to turn in my laptop for a desktop just to finish this movie, will the imac 1.9 G5 w/ 160 HD solve my problem?

Hi Anna - welcome to the forum!
1. The HD may be 60 GB, but how much AVAILABLE space do you have?
2. For the size of your project, 512mb RAM is probably minimum - I think you should increase that to at least 750.
3. The iBook is OK for iMovie projects generally (I sometimes use one also), but your project is extremely large - much larger than would be considered usual.
4. I also use a large capacity external HD and that may be an option for you - maybe 200GB (formatted for Mac - (Mac OS Extended).
4. Remember that if you intend making a DVD, that iDVD has a maximum size of 120 minutes, and yours is well over that.
Obviously a more powerful computer is better, but I would try adding RAM to your iBook before spending mega-dollars. Even on my desktop computer, a project as long as yours would begin to display similar problems to the one you are experiencing.
Does this help?

ProRes to Blu-Ray H.264, then Preview problems in Encore CS5

Hello all,
I've been taking 90 minute or so ProRes 422 QuickTimes (29.97 interlaced) into Media Encoder CS 5 and creating H.264 Blu-Ray files for use in Encore CS5. I'm using the 1080i maximum quality setting and adjusting it so that target bitrate is 25mbps and max is 30. Also doing 2-pass VBR.
The issue I'm having is when I import these files into Encore CS5 and then preview them in a timeline they are artifacting all over the place. They look like my cable signal when it breaks up, except through the entire program. I've re-transcoded in the Media Encoder and am having the same issue. I've also tried transcoding within Encore (which is really the same thing), and still it persists. I haven't made a BD-R yet to check that and I know the preview in Encore CS 5 is very buggy. But I'm wondering -- has anyone run into this? Is this just a preview problem, or is there something actually wrong with the transcodes?
Also, if anyone has a tip for where I can open the *.m4v files coming out of Media Encoder so that I can check them somewhere other than in Encore that would be awesome. VLC player doesn't work, neither does QuickTime. Thanks everyone!
Best,
JD

Jeff,
Thanks for the response. Here are the answers to your questions:
Some obvious but necessary checks:
Are you authoring in a Blu-ray project and not a DVD project? YES, it is a 1080i 29.97 Blu-Ray project.
Are you checking the transcode status column for Blu-ray and not DVD? Definitely looking at the transcode status for Blu-Ray, and not DVD.
If all is OK with those checks, then please check the audio:
Are the files multiplexed? If so, try elementary streams.
Are you using elementary streams? If so, try multiplexed.
On these notes -- what is a good way for me to know if the transcoded files are multiplexed or elementary? The interesting thing is that when I bring in the M4V and WAV files into Encore from what AME creates, the WAV file does NOT require transcoding, but the video file (M4V) does.
Regarding the preview issue I was having it's worth noting that when I checked back in preferences the playback quality was still set to DRAFT, as if when I switched it to HIGH it just didn't take (and I tried this more than once). I put it to HIGH again today and this time it seems it took, as preview playback quality is good again. Just seems strange to me that Encore has a mind of it's own sometimes with certain things.
I'm really more concerned with the transcoding at this point. I did a project a couple weeks back where I just bit the bullet and transcoded the M4V again in Encore to author the ISO file, and several chapters of the program came out stuttering on the disc. The original Quicktime source is fine and the preview playback on it was fine during those chapters. I can't seem to find a throughline for these problems -- just seems to happen every now and then and can't control it.
I authored a 53 minute 1080p 23.98 disc in early January that worked beautifully. Everything was great - no problems.

Preview problems, Premiere CS5 Windows

Hi!
I´ve been using Premiere for 10 years, so I should know it pretty well, but this is my case:
I start Premiere, choose "New project", tried different sequence settings, but the DVCPro HD 25 (PAL) is the most relevant. Inside Premiere, I import a clip, and drag it onto the timeline. So far, everything´s normal. The problems starts when I press the space button for preview. The only thing´s happening is the play symbol changes to a stop symbol in the composition window. No timecode´s running, no moving marker, and only a still image in the composition window. I can jog it frame by frame, and I can move the marker, and everything is fine, but also no playback. The play button in comp window does not make a change.
My next problem is to get this version to work with my Black Magic Decklink Extreme. I have an output signal, but no picture.
My system:
Pentium i7
12GB RAM
Win 7
Anybody?
Erik
Norway

Thanks, but I´ve found a problem with my Decklink Extreme PCI card. The Premiere preview problem happens only when I´m using any Black Magic presets. Is Decklink Extreme PCI/windows 7/Adobe CS5 a bad combination? I´m not able to get any picture on my monitor from the decklink what so ever (composite/component), but there´s a signal there (black video). Worked fine in XP (with CS3), kind of worked in win7 with my old configuration (4GB RAM, single core AMD-processor), and absolutely no response now.

Preview Problem: PDF file:Adobe livecycle designer ES 10.0

Hallo.
How do I fix preview problem of a .pdf file that was created with Adobe livecycle designer es 10.0. version 1.7 ( show on the properties of the file). The file opens normally. No preview in explorer preview pane and change to printing problem too. Need to preview the file before uploading it onto the internet. All updates done: Windows 7, Explorer 11, Java (Javascript enable) Adobe reader XI. and Adobe Reader XI Pro.(Trail version). When in Explorer and using open with:Default program: select software already in stalled on computer: Browse Adobe reader XI (Acrord32.exe: properties show version 11.0.06.70) This will show as Adobe reader 9.4 on the list of programs.

If you purchased a prior license of Acrobat and have purchased an upgrade to Acrobat XI Pro then you are eligible for free LiveCycle Designer upgrade.
See more information on: http://www.adobe.com/products/acrobatpro/faq.edu.html
Visit the http://www.adobe.com/go/learn_acr_livecycle_upgrade_en to request an upgrade.

I got render and RAM preview problems. help?

i got render and RAM preview problems with after effects! please help me
when i started on a project earlier today the RAM preview was failing and it stoped making a preview after about a second, when i hit the RAM preview buttom again it continued to load and stoped again after a half second, and it continued to do that till it wasn't loading at all, just playing the same thing up even doe it haden't loaded the whole composition! BUT if i moved the (thing you see where you are on the timeline in need of a better name) it started loading a little more and then it stoped again.. so after alot of problems and moving i managed to make a RAM preview of the whole composition..
now the real problem: when i was done with my project and i was going to reender i did like this: i added my composition to the render queue, chosed my render settings and started to render, after exactly 37 frames it stoped and no window or anything poped up, the only thing that was telling me something was wrong was the render status, and it said: ''failed at 0;00;00;37'' that's not even a second! and BTW when i render after effects only uses 12% of my 6GB RAM memory.. i dont know what to do! i've tried other render settings but the same thing happens! can anyone help me?
BTW i'm swedish and only 14 so i might misspelled something..

Start here and make sure that you understand how RAM preview is supposed to work first:
http://forums.adobe.com/thread/424030
What version of After Effects? Have you installed the recent updates? What operating system? What kind(s) of source footage? Has this ever worked before? What other software are you running? Do you have any third-party effects or codecs installed? Are you rendering with OpenGL?
What are your Memory & Multiprocessing settings? Are you using Render Multiple Frames Simultaneously multiprocessing?

Repair/verify disk permissions and Preview problem.

The preview problem is yet to be solved + is outlined here:
http://discussions.apple.com/thread.jspa?threadID=298858&tstart=0
Also:
I decided to open up disk utility and verify disk permissions, this went fine. I then went on to 'verify disk' and it told me:
Volume Header needs minor repair
The volume Macintosh HD needs to be repaired.
Error: The underlying task reported failure on exit
1 HFS volume checked
Volume needs repair
What's the solution? start up from OSX install disc? is this hard to do?

I am also having trouble with "verify disk permissions".
I have had frequent crashes recenlty and as a result upgraded to Tiger. The system crashes sometime when recovering from sleep (twice yesterday) and was crashing ferquently in Panther OS when hitting the odd key here and there.
Since upgrading to Tiger, I have apparrently successfully "repaired the disc permissions" on the start up volume, but then when I come to check them again, there are still the same problems, even though the "disk utility" has been run successfully. Have run disc warrior and "Verify disk" and still not convinced.
I also notice that the machine seems to be much slower running Tiger than before.
I avoided a complete install of the new OS because of all the aggro that involves, but it may be my only option if no one can help.
All thoughts appreciated.
Thanks
Powerbook 12 Mac OS X (10.4.5)

Any Help For Yet Another HDCP For Playback/Netflix Problem?

I have a very complex set-up and had no problem streaming until the other night and I have tried every single solution I can find online under the sun so that is why I am posting here.
I have a Pioneer Receiver that I used a Terk Smart HDMI 3 x 1 Selector with and was able to stream Netflix with no problem.
This is how everything used to be set up:
Pioneer Receiver
Blu-ray IN
HDMI OUT Terk
DVD IN
Panasonic DVD Recorder OUT
OUT
Panasonic LCD TV HDMI 1
Terk HDMI 3 x 1 Selector
OUT
Pioneer Receiver Bluray IN
Panasonic Bluray Player
Input 1
AppleTV (3rd Gen.)
Input 2
Mac Mini (2010)
Input 3
Now here's the rub: I also have a PS3. I used to unplug either the ATV or Mini whenever I wanted to use it and I got tired of switching out so I bought a Monoprice 8 x 1 HDMI Selector. The logic here being that I would have more than enough HDMI inputs to plug in everything.
When I first hooked up the Monoprice, I hooked the OUT from it into the Bluray IN on the Pioneer and then hooked all of the HDMI cables from all of the various electronics into the INputs on it. Tested all of them to see that it autoselected whatever I had chosen and even was able to stream on NF.
This is how I have everything hooked up now:
Monoprice 8 x 1
OUT
Pioneer Receiver Bluray IN
ATV
Input 1
Panasonic Bluray Player
Input 2
PS3
Input 3
Mac Mini
Input 4
Panasonic DVD Recorder*
Input 5
*Bluray IN and OUT are the only HDMI slots in use on the Pioneer Receiver using this hookup.
Now all of a sudden yesterday I went to stream NF via the ATV and I got that "This content requires HDCP for playback" error.
I did everything I could think of and also tried all of the suggestions I could find on the web. I had already switched out the HDMI cables as I had bought new ones when I got the Monoprice. So I hooked the Terk back up thinking it would "fix" things. No dice. I put the old HDMI cables back on. No dice. I have it hooked up now with the old HDMI cables and still no dice. I unplugged everything and let it sit thinking I could force a new HDMI handshake. NF started streaming for 5 seconds and froze -- and then the error message.
I also have a Scientific Atlanta DVR that the ATV is plugged into that the HDMI 2 of the Panasonic TV is connected via HDMI. The Panasonic TV isn't "old" as I think I got it in late 2009 or late 2010, as it has more than enough HDMI inputs, component, and also a PC connection -- in case someone wanted to suggest the TV wasn't capable of handling the hookups. The ATV is running the latest version of the software.
This is really frustrating since it worked with no problem from the day I got the ATV and now after upgrading the switcher to get more HDMI inputs, everything went kaput.
And I just don't know what to do.
I'm not sure if having everything being dependent upon the Panasonic TV being powered on is affecting things, but it never affected things when I was using the 3 x 1 HDMI switch. When I wanted to use the ATV, I'd press the Bluray input on the Pioneer receiver, hit the ATV remote and it would come on. Click into NF and voila: streaming with no problems.
Currently, I still do the same thing -- and I can listen to the radio, stream in iTunes Match on the ATV. It's just the NF issue that's really beyond me. The only thing I can think of to try is to maybe put the DVR in the surge protector slot so that it has to be powered on so that everything else will power up instead of the TV?
I'm hoping someone has a suggestion that involves something other than restarting/restoring the ATV, or unplugging things for 30 seconds because I have tried everything I've come across. I just don't know what to do but I really would like to be able to use NF on the ATV because I like the fact that it plays in Dolby, and I really don't want to have to go back to the PS3 to utilize that feature.
In the meantime, I guess I will switch the DVR on the surge protector with the TV and see what happens if I change the way things power up in the chain.

I am at a loss. I thought I had a micro USB cord but since I didn't, I wasn't able to downgrade the software.
I did a complete restore for kicks.
This is the current setup
ATV HDMI
Panasonic TV HMDI 2
ATV optical output
Pioneer Receiver
Again, all of the other devices run through the 8 x 1 switch box which is NOT powered on to use the ATV.
I get the HDCP error whenever I try to access the following:
Netflix
Trailers
Vimeo
WSJ Live
HHL and the other sports channels
These work fine:
Radio
iTunes Match
Podcasts
Flickr
TV Shows and Movies because I tested both watching previews and they streamed perfectly
I've changed the settings on the ATV until I'm blue in the face and this is what they are currently:
Dolby - Auto
Audio Output - Auto
HDMI Output - Auto
TV Resolution - 1080p HD - 60Hz -- and yes I've had it set on both "Auto" and 720p HD - 60Hz and neither stopped the error once it started happening
All of the equipment is HDCP compliant as I checked
The cable between the TV and ATV
The 8 x 1 switch box
Panasonic TV specs -- it is HDCP compliant as I said in my 3rd post (according to the manual)
The Pioneer Receiver (for good measure)
I have no idea of what to do other than to hope that Apple does something with the next update to restore everything, as this HDCP issue is really beyond annoying and it's clear 5.2 broke something. In the meantime, I really am open to suggestions to try something else other than smashing the ATV with a hammer

Adjustments affecting playback preview quality?

Hi,
I'm probably doing soemthing wrong again.
My video preview plays fine until I add any kind of adjustments to a clip, even as simple a vibrancy adjustmment. After I render then the preview gets very degraded and blocky.
i just undid all of my adjustments to my movie and re-rendred and instead of it being a green line through every clip, half have no line. The ones with no line playpback fine, but the ones with green lines playback bad quality.
Of course if I ad an adjustment to the clips that look fine,adn render, they get bad again.
I know this only afects the preview (atleast i think it is, the output looks ok) but its abit diffcult working with video and trying to make proper adjustments when its difficult to see what you are doing because the quality turns to mush.
Still learning PE11, and i need to get this little project done in the next 2 weeks or so.
I tried searching about this bit can't seem to find an answer
Thanks
Jim

Yes its still doing it with a photo
I loaded this into the same AVCHD 60 project...
(photo shot with Canon 5D Mark III)
Added vibrancy and some brightness, rendered and it changes it to this...
There is a MUCH bigger drop off in quality however with the video than this...... but as you can see its still doing it.
And my computer should have no problems handling this video..... Quad 3.5GHz i7, 16GB, nVidia 670, PE11 running off SSD on Mac
I also just tested it on a 1080i 30 created project and it was much worse than the exmaple above.
EDIT:
Something else I think i should mention, I didn't think of this until now, but I'm not sure this should matter, but my mac is a hackintosh I build myself in December. I've had absolutely zero isues with it or any conflicts with any other programs or software. Unless there is some conflict with the video card and this software, but from my knowlsege that shouldn't happen.
I have Win7 running on a seperate SSD drive, i'm going to try and get some video editing software on there, maybe a PE11 trial, and see what happens.Just to rule that out.

Video preview problem

Hi. I have a problem with video playback in my premiere cc. In project window I have video file imported, video is on timeline, but I can't see this video preview in program and source windows. I haven't worked a lot in premiere and I don't know where the problem is. I have already reinstalled program, but it didn't solve the problem. Can someone help me? Additionally, when I render this video, everything is fine,...problem is that, I can't see what I render

More information needed for someone to help... please click below and provide the requested information
-Premiere Pro Video Editing Information FAQ http://forums.adobe.com/message/4200840
•What is your exact brand/model graphics adapter (ATI or nVidia or ???)
•What is your exact graphics adapter driver version?
•Have you gone to the vendor web site to check for a newer driver?
•For Windows, do NOT rely on Windows Update to have current driver information
•-you need to go direct to the vendor web site and check updates for yourself
•nVidia Driver Downloads http://www.nvidia.com/Download/index.aspx?lang=en-us
•ATI Driver Autodetect http://support.amd.com/en-us/download/auto-detect-tool
Exactly what is INSIDE the video you are editing?
Codec & Format information, with 2 links inside for you to read http://forums.adobe.com/thread/1270588
Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
https://forums.adobe.com/thread/1070933 for screen shot instructions
Free programs to get file information for PC/Mac http://mediaarea.net/en/MediaInfo/Download

Previewing problem

Two questions here that I hope someone can help me out with, I'm getting there slowly but surely and having a heck of a lot of fun with iMovie...
1) One problem with iMovie 9.0.2 -- I'm using a number of picture in picture (PIP) movie clips which have alpha channels for transparency. After inserting these clips, when I preview the movie by hitting the space bar, sometimes I see the whole movie just as it should look with the PIP working and sometimes, the movie continues on but the PIP is missing or the sequence "holds" on one frame until the PIP finishes and then the movie continues on as normal until the next PIP starts. Is this a not-enough-memory problem or some sort of glitch? A cache problem, maybe? I've got 8 GB of RAM and I'm using the internal 7200 RPM drive in my iMac 2.66GHz Intel Core i5 for the application and media files.
2) When I run two PIP's side by side, one after another, is it possible to blend them together somehow? For example, I have an explosion in one PIP over top of some footage and I've used a second PIP of smoke. Looks kind of amateurish having just the explosion and then the smoke follow right afterwards. I'd like the smoke to start about 1 second before the explosion ends so that the smoke becomes part of the explosion. Not sure if this is possible? When I try to slide them into place, I can't get one PIP to fade into the other. Hope this makes sense.
Thanks so much to everyone who has helped me out so much in this forum.

The level of what you're trying to accomplish I think may be very nearly the limit of what iMovie can show you live previews of while editing. With other video editing programs, you can tell them to 'render' the effects if you are getting bad playback performance. iMovie doesn't render anything until you do the final step of exporting out under the Share Menu. This sometimes is necessary for people who want to have a video 'watermark' placed on their video clips. In those cases what they do is create the whole video as they intended without the watermark, then export to the desktop. Re-import that final version of the video back into iMovie then use PIP to add the transparent watermark on top of the existing video. This gets around many limitations of the PIP effect (like not working with transitions properly). So the best answer I can give is if it's not previewing properly, try doing a test by exporting what you have made so far to a single exported video clip and see how it looks there.
Transitions between PIP is going to be impossible as the second video 'channel' in iMovie doesn't allow for transitions between those overlaid clips. You would need to move up to a more expensive video editing program to get that capability.

Video Preview problems

When browsing iTunes store I am unable to preview videos - just get a blank screen.
Checked on all computers in the house and the same occurs. Tried from work with no problems!
Anyone got any ideas?
Tried turning off AV/AS and some firewall rules with no joy

There is a slightly newer 10.1.1 version of drivers available from Blackmagic:
http://www.blackmagicdesign.com/support
Thanks for posting the screenshot. This shows that After Effects does not see the Mercury Transmit plug-in for Blackmagic. You should verify whether the plug-in is present:
os drive/Library/Application Support/Adobe/Common/Plug-ins/7.0/MediaCore/
The file will be named DeckLinkTransmit.bundle, or something similar.
If the file is present, try uninstalling and reinstalling the (latest version of) Blackmagic drivers.
If After Effects still does not recognize the Blackmagic Mercury Transmit plug-in, open Premiere Pro CC 2014 and check Preferences > Playback, and whether or not video preview works there.

Crystal Report Preview Problem

Dear All,
I have done a crystal report for Sales Quote and imported using Administration-->Setup-->General-->Reports and Layouts.
It shows that the report is imported successfully but when i go and give print preview, it shows an error as "LogOn Failed Please Try Again".
I dont know why this error occurs.
But the other reports are working well.
Help me solving this issue.
Regards,
Janani

hi
Janani..
Actually i never Seen This Type of problem..
I have one Doubt May be u have Developed in ur system n then import it to the client server..
before importing have u change the login credentials....
After i search i got below link just have a look on below post If it's not use ful just ignore the mail....
System asks for SA Password when printing with Crystal Reports

Playback/Previewing Problems

Similar Messages

Maybe you are looking for